Test Report

FCC ID: SFB-HR135

Test Report

Download: PDF
FCCID_1920130

Shenzhen Certification Technology Service Co., Ltd 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2nd Road, Bao'an District, Shenzhen 518126, P.R. China. TEST REPORT FCC ID: SFB-HR135 Applicant : MILO ENTERPRISES INC. Address : 603-7281 CAMBIE STREET, VANCOUVER, B. C. V6P 3H4 CANADA Equipment under Test (EUT): Name : Electronic Pest Repeller Model : HR135, HR132, HR136 Standards : FCC PART 15, SUBPART C : 2012 (Section 15.231) Report No. : STI130123026 Date of Test : March 05-12, 2013 Date of Issue : March 12, 2013 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above Authorized Signature (Mark Zhu) General Manager The manufacture should ensure that all the products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of Shenzhen Certification Technology Service Co., Ltd. Or test done by Shenzhen Certification Technology Service Co., Ltd. Approvals in connection with, distribution or use of the product described in this report must be approved by Shenzhen Certification Technology Service Co., Ltd. Approvals in writing. FCC ID: SFB-HR135 Page 1 of 29

Report No.: STI130123026 TABLE OF CONTENT Description Page 1 General Information------------------------------------------------------------------------------------ 3 1.1 Description of Device (EUT) --------------------------------------------------------------------- 3 1.2 Description of Test Facility ----------------------------------------------------------------------- 3 2 EMC Equipment List ----------------------------------------------------------------------------------- 4 3 Test Procedure ------------------------------------------------------------------------------------------ 5 4 Summary of Measurement--------------------------------------------------------------------------- 6 4.1 Summary of test result ----------------------------------------------------------------------------- 6 4.2 Block Diagram -------------------------------------------------------------------------------------- 6 4.3 Assistant equipment used for test ---------------------------------------------------------------- 6 4.4 Test Conditions ------------------------------------------------------------------------------------- 7 4.5 Measurement Uncertainty (95% confidence levels, k=2)------------------------------------- 7 5 Radiation Emission ------------------------------------------------------------------------------------ 8 5.1 Radiation Emission Limits(15.209&231)------------------------------------------------------- 8 5.2 Test Setup-------------------------------------------------------------------------------------------- 8 5.3 Test Procedure -------------------------------------------------------------------------------------10 5.4 Test Equipment Setting For emission test.-----------------------------------------------------11 5.5 Test Condition -------------------------------------------------------------------------------------11 5.6 Test Result ------------------------------------------------------------------------------------------11 6 POWER LINE CONDUCTED EMISSION ------------------------------------------------------- 17 6.1 Conducted Emission Limits(15.209) -----------------------------------------------------------17 6.2 Test Setup-------------------------------------------------------------------------------------------17 6.3 Test Procedure -------------------------------------------------------------------------------------18 6.4 Test Results-----------------------------------------------------------------------------------------18 7 Occupied bandwidth--------------------------------------------------------------------------------- 19 7.1 Test limit --------------------------------------------------------------------------------------------19 7.2 Method of measurement --------------------------------------------------------------------------19 7.3 Test Setup-------------------------------------------------------------------------------------------19 7.4 Test Results-----------------------------------------------------------------------------------------19 8 Transmission time------------------------------------------------------------------------------------ 21 8.1 Test limit --------------------------------------------------------------------------------------------21 8.2 Method of measurement --------------------------------------------------------------------------21 8.3 Test Setup-------------------------------------------------------------------------------------------21 8.4 Test Results-----------------------------------------------------------------------------------------21 9 Band Edge Check------------------------------------------------------------------------------------- 23 9.1 Test limit --------------------------------------------------------------------------------------------23 9.2 Test Procedure -------------------------------------------------------------------------------------23 9.3 Test Setup-------------------------------------------------------------------------------------------23 9.4 Test Result ------------------------------------------------------------------------------------------23 10 Antenna Requirement ------------------------------------------------------------------------------- 24 10.1 Standard Requirement ----------------------------------------------------------------------------24 10.2 Antenna Connected Construction ---------------------------------------------------------------24 10.3 Result------------------------------------------------------------------------------------------------24 11 Photographs of Test Setup ------------------------------------------------------------------------ 25 12 Photographs of EUT --------------------------------------------------------------------------------- 26 FCC ID: SFB-HR135 Page 2 of 29

Report No.: STI130123026 1 General Information 1.1 Description of Device (EUT) Trade Name : N/A EUT : Electronic Pest Repeller Model No. : HR135, HR132, HR136 Only different in Model No., the other the same. DIFF. : The test model: HR135. Type of Antenna : PCB antenna, Max Gain 0dBi. Operation Frequency : 433.92 MHz Channel number : 1 Modulation type : OOK Power Supply : DC 12V Supply by battery Rated PF output Power 61.67 dBuV (Peak detector) Applicant : MILO ENTERPRISES INC. Address : 603-7281 CAMBIE STREET, VANCOUVER, B. C. V6P 3H4 CANADA Manufacturer : HANDLE TECH ELECTRONICS(SZ) CO., LTD Address : A4-3A Niu Jiao Long Industrial Zone, Zhang Keng Jing Village, Guan Lan, Long-Hua New District, Shenzhen City, 518110 China 1.2 Description of Test Facility Shenzhen Certification Technology Service Co., Ltd. 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2nd Road, Bao'an District, Shenzhen 518126, P.R. China FCC Registered No.:197647 FCC ID: SFB-HR135 Page 3 of 29

Report No.: STI130123026 2 EMC Equipment List Equipment Manufacture Model No. Serial No. Last cal. Cal Interval 3m Semi-Anechoic ETS-LINDGREN N/A SEL0017 Nov. 16, 12 1Year Spectrum analyzer Agilent E4407B MY49510055 Oct. 31, 12 1Year Receiver R&S ESCI 101165 Oct. 31, 12 1Year Receiver R&S ESCI 101202 Oct. 31, 12 1Year Bilog Antenna SCHWARZBECK VULB 9168 9168-438 Feb.20, 13 1Year Horn Antenna SCHWARZBECK BBHA 9120 D BBHA 9120 Feb.20, 13 1Year D(1201) Horn Antenna SCHWARZBECK BBHA 9170 BBHA 9170 Feb.20, 13 1Year D(1432) Active Loop Beijing Daze ZN30900A SEL0097 Feb.20, 13 1Year Antenna L.I.S.N. SCHWARZBECK NSLK8126 8126466 Oct. 31, 12 1Year Cable Resenberger N/A No.1 Oct. 31, 12 1Year Cable SCHWARZBECK N/A No.2 Oct. 31, 12 1Year Cable SCHWARZBECK N/A No.3 Oct. 31, 12 1Year Pre-amplifier SCHWARZBECK BBV9743 9743-019 Oct. 31, 12 1Year Pre-amplifier Quietek AP-180C CHM-0602012 Oct. 31, 12 1Year FCC ID: SFB-HR135 Page 4 of 29

Report No.: STI130123026 3 Test Procedure POWER LINE CONDUCTED INTERFERENCE: The test procedure used was ANSI Standard C63.4-2003 using a 50ｕH LISN. Both Lines were observed. The bandwidth of the receiver was 10kHz with an appropriate sweep speed. The ambient temperature of the EUT was 25℃ with a humidity of 58%. RADIATION INTERFERENCE: The test procedure used was ANSI Standard C63.4-2003 using a ANRITSU spectrum analyzer with a pre-selector. The analyzer was calibrated in dB above a micro volt at the output of the antenna. The resolution bandwidth was 100kHz and the video bandwidth was 300 kHz up to 1 GHz and 1 MHz with a video BW of 3MHz above 1 GHz. The ambient temperature of the EUT was 25℃ with a humidity of 58%. FORMULA OF CONVERSION FACTORS: The Field Strength at 3m was established by adding the meter reading of the spectrum analyzer (which is set to read in units of dBuV) to the antenna correction factor supplied by the antenna manufacturer and cable loss. The antenna correction factors and cable loss are stated in terms of dB. The gain of the Pre-selector was accounted for in the Spectrum Analyzer Meter Reading. Example: Freq (MHz) METER READING + ACF + CABLE = FS 33.20 dBuV + 10.36 dB + 0.9 dB= 44.46 dBuV/m @ 3m ANSI STANDARD C63.4-2003 10.1.7 MEASUREMENT PROCEDURES: The EUT was placed on a table 80 cm high and with dimensions of 1m by 1.5m. The EUT was placed in the center of the table (1.5m side). The table used for radiated measurements is capable of continuous rotation. When an emission was found, the table was rotated to produce the maximum signal strength. At this point, the antenna was raised and lowered from 1m to 4m. The antenna was placed in both the horizontal and vertical planes. The situation was similar for the conducted measurement except that the table did not rotate. The EUT was setup as described in ANSI Standard C63.4-2003 10.1.7 with the EUT 40 cm from the vertical ground wall. FCC ID: SFB-HR135 Page 5 of 29

Report No.: STI130123026 4 Summary of Measurement 4.1 Summary of test result Test Item Test Requirement Stanadard Paragraph Result Spurious Emission FCC PART 15: 2012 Section 15.231&15.209 Compliance Conduction Emission FCC PART 15: 2012 Section 15.207 Not applicable Occupied bandwidth FCC PART 15: 2012 Section 15.231 Compliance Transmission time FCC PART 15: 2012 Section 15.231 Compliance Band Edge FCC PART 15: 2012 Section 15.231 Not applicable Antenna Requirement FCC PART 15 : 2012 Section 15.203 Compliance Note: All buttons of the EUT have been tested and only worst case reported. The EUT has been tested as an independent unit. And Continual Transmitting in maximum power (The new battery be used during Test) 4.2 Block Diagram EUT 4.3 Assistant equipment used for test Description : N/A Manufacturer : N/A Model No. : N/A FCC ID: SFB-HR135 Page 6 of 29

Report No.: STI130123026 4.4 Test Conditions Temperature range 21-25℃ Humidity range 40-75% Pressure range 86-106kPa 4.5 Measurement Uncertainty (95% confidence levels, k=2) Item MU Remark Uncertainty for Power point Conducted Emissions 2.50dB Test Uncertainty for Radiation Emission test in 3m 3.04dB Polarize: V chamber (30MHz to 1GHz) 3.02dB Polarize: H Uncertainty for Radiation Emission test in 3m 3.84dB Polarize: H chamber (1GHz to 25GHz) 3.56dB Polarize: V Uncertainty for radio frequency 1×10-9 Uncertainty for temperature 0.2℃ Uncertainty for humidity 3% Uncertainty for DC and low frequency voltages 0.06% FCC ID: SFB-HR135 Page 7 of 29

Report No.: STI130123026 5 Radiation Emission 5.1 Radiation Emission Limits(15.209&231) Frequency Field Strength (MHz) Limits at 3 metres (watts, e.i.r.p.) uV/m dB uV/m Measurement distance(m) 0.009-0.490 2400/F(kHz) XX 300 0.490-1.705 24000/F(kHz) XX 30 1.705-30 30 29.5 30 30~88 100(3nW) 40 3 88~216 150(6.8nW) 43.5 3 216~960 200(12nW) 46 3 Above960 500(75nW) 54 3 Carrier 80.8(AV) 3 frequency Carrier 100.8(PK) 3 frequency NOTE: a) The tighter limit applies at the band edges. b) Emission Level(dB uV/m)=20log Emission Level(Uv/m) 5.2 Test Setup See the next page. FCC ID: SFB-HR135 Page 8 of 29

Report No.: STI130123026 Below 30MHz Test Setup Above 30MHz Test Setup FCC ID: SFB-HR135 Page 9 of 29

Report No.: STI130123026 Above 1GHz Test Setup 5.3 Test Procedure a) The measureing distance of 3m shall be used for measurements at frequency up to 1GHz and above 1GHz, The EUT was placed on a rotating 0.8 m high above ground,The table was rotated 360 degrees to determine the position of the highest radiation b) The Test antenna shall vary between 1m and 4m,Both Horizontal and Vertical antenna are set ot make measurement. c) The initial step in collecting conducted emission data is a spectrum analyzer Peak detector mode pre-scanning the measurement frequency range. Significent Peaks are then marked. and then Qusia Peak Detector mode remeasured d) If Peak value comply with QP limit Below 1GHz.The EUT deemed to comply with QP limit. But the Peak value and average value both need to comply with applicable limit above 1GHz. e) For the actual test configuration, please see the test setup photo. FCC ID: SFB-HR135 Page 10 of 29

Report No.: STI130123026 5.4 Test Equipment Setting For emission test. 9KHz~150KHz RBW 200Hz VBW1KHz 150KHz~30MHz RBW 9KHz VBW 30KHz 30MHz~1GHz RBW 120KHz VBW 300KHz Above 1GHz RBW 1MHz VBW 3MHz 5.5 Test Condition Continual Transmitting in maximum power(The new battery be used during Test) 5.6 Test Result We have scanned the 10th harmonic from 9KHz to the EUT. Detailed information please see the following page. From 9KHz to 30MHz: Conclusion: PASS Note: The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. FCC ID: SFB-HR135 Page 11 of 29

\\ I ,/ Shenzhen Catifcation TechnologySenice Co Ltd N 2 2F, Eulding B, East Area ofNanchang Second Industral Zone 2XC Gushu 2nd Road. Bacan Distict, Shenzhen 519126 PR Chin cC—ss To aoosraston hk sdsc esnsrecasr rommomaiverad Webste: hitp lnim cessz com Email Senice@cessz com ts1 rie. pctest ontadpthtmio.«s3ussems (0 ,Level0Bu¥im) Dste:20130305 Tme:torear o o 1 rcomat 188 so «o | 30 20 f 10 5o ton. z00. son. 400. s00..— son. om. son. son.— tove Frequency (ii) snn

\\ I ,/ Shenzhen CetifcationTechnologySenice Co Ltd N 2 2. Bulding ©, East Area of Nanchang Second Industral Zone 2NC Gushu 2nd Road. Beoan Distict Shenzhen 519126 PR Chira CS Car aoosres 100 rAx. «onresnsracasr CPTationTecinetons Webste:hitp vincessz com Email Senice@cessz com Do2 rie.oitest oatada@bitstinto—assussems (0 ,Level0Bu¥im) Dste:2013.05—12 Time: tozzso o 1 o matise so «o 30 20 10 5o ton. 200. aon. ao0. Son. sn yom. 200. son. tovo Frequency (iit)

\\ I ,/ Shenzhen CetifcationTechnologySenice Co Ltd N 2 2. Bulding ©, East Area of Nanchang Second Industral Zone 2NC Gushu 2nd Road. Beoan Distict Shenzhen 519126 PR Chira CS Car aoosres 100 rAx. «onresnsracasr CPTationTecinetons Webste:hitp vincessz com Email Senice@cessz com ts1 rie:oitest ontaghtittmLo«s3aBove 1szie (@) .LeveldBu¥im) Dste:2013.03.05 Time: touess ree pht 1s105 peax o o reo part 1s1eave so 5 «o s0 20 10 Tooo zooo soon 4000 soon sovo Frequency (iit)

\\ I ,/ Shenzhen CetifcationTechnologySenice Co Ltd N 2 2. Bulding ©, East Area of Nanchang Second Industral Zone 2NC Gushu 2nd Road. Beoan Distict Shenzhen 519126 PR Chira CS Car aoosres 100 rAx. «onresnsracasr CPTationTecinetons Webste:hitp vincessz com Email Senice@cessz com Do2 rie:oitest ontaghtittmLo«s3aBove 1szie (@) ,LeveldBu¥im) Dste:2013.03.05 Time: 135222 ree pht 1s105 peax o o reo part 1s1eave so > 10 f «o 30 20 10 Tooo zooo 5ooo 4ovo sooo sote Frequency (iit)

Report No.: STI130123026 Radiated Emissions Result of Inside band (433.92MHz) EUT car remote control Model Name K01 Temperature 25oC Relative Humidity 56% Pressure 960hPa Test voltage DC 3V Supply by battery Test Mode TX Antenna polarization Horizontal/Vertical Channel (433.92MHz) Fre. Plority Reading Antenna Cable Amplifier Correct Measure Limit Margin dBuV Factor Loss Gain Factor Result dBuV/m dB MHz H/V dB dB dB dB dBuV/m 433.92 H 72.89（PK） 15.58 0.67 27.47 -11.22 61.67 100.8（PK） -39.13 433.92 H / / / / / 61.67 80.8（AV） -19.13 -- H -- -- -- -- -- -- -- -- 433.92 V 65.24（PK） 15.58 0.67 27.47 -11.22 54.02 100.8（PK） -46.78 433.92 V / / / / / 54.02 80.8（AV） -26.78 -- V -- -- -- -- -- -- -- -- Note: Peak result is under the AV limit already, the AV measurement is not required Notes: 1 --Means other frequency and mode comply with standard requirements and at least have 20dB margin. Correct Factor=Cable Loss+Antenna Factor-Amplifier Gain Measurement Result=Reading + Correct Factor Margin=Measurement Result-Limit 2 –Spectrum setting: a. Peak setting 30MHz-1GHz, RBW=120KHz,VBW=300KHz. b. AV setting 30MHz-1GHz, RBW=1MHz,VBW=10Hz. FCC ID: SFB-HR135 Page 16 of 29

Report No.: STI130123026 6 POWER LINE CONDUCTED EMISSION 6.1 Conducted Emission Limits(15.209) Frequency Limits dB(µV) MHz Quasi-peak Level Average Level 0.15 -0.50 66 -56* 56 - 46* 0.50 -5.00 56 46 5.00 -30.00 60 50 Notes: 1. *Decreasing linearly with logarithm of frequency. 2. The lower limit shall apply at the transition frequencies. 3.The limit decreases in line with the logarithm of the frequency in the rang of 0.15 to 0.50 MHz. 6.2 Test Setup FCC ID: SFB-HR135 Page 17 of 29

Report No.: STI130123026 6.3 Test Procedure The EUT is put on the plane 0.8m high above the ground by insulating support and is connected to the power mains through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm coupling impedance for the EUT system. Please refer the block diagram of the test setup and photographs. Both sides of AC lines are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to ANSI C63.4-2003 on Conducted Emission Measurement. The bandwidth of test receiver (R & S ESCS30) is set at 9 kHz. 6.4 Test Results EUT power supply by battery, so the test not applicable. FCC ID: SFB-HR135 Page 18 of 29

Report No.: STI130123026 7 Occupied bandwidth 7.1 Test limit Please refer section15.231 According to§15.231(C), The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70MHz and below 900MHz. 7.2 Method of measurement a)The bandwidth is measured at an amplitude level reduced 20dB from the reference level. The reference level is the level of the highest amplitude signal observed from the transmitter at the fundamental frequency. Once the reference level is established, the equipment is conditioned with typical modulating signal to produce the worst-case (i.e. the widest) bandwidth. b)The test receiver RBW set 30KHZ,VBW set 30KHZ,Sweep time set auto. 7.3 Test Setup Spectrum EUT Analyzer 7.4 Test Results PASS. Detailed information please see the following page. Frequency Test Limit Result Result 433.92MHz 125KHz <1.08MHz Pass FCC ID: SFB-HR135 Page 19 of 29

Report No.: STI130123026 FCC ID: SFB-HR135 Page 20 of 29

Report No.: STI130123026 8 Transmission time 8.1 Test limit Please refer section15.231 According to §15.231(a)(1), A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. According to §15.231(a)(2), A transmitter sctivated automatically shall cease transmission within 5 seconds after activation. 8.2 Method of measurement 7.2.1. Place the EUT on the table and set it in transmitting mode. 7.2.2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 7.2.3. Set spectrum analyzer Center=433.9MHz, Span = 0MHz, Sweep = 200ms. 7.2.4. Set the spectrum analyzer as RBW, VBW=1MHz, 7.2.5. Max hold, view and count how many channel in the band. 8.3 Test Setup Spectrum EUT Analyzer 8.4 Test Results PASS. Detailed information please see the following page. Frequency Test Limit Result Result 433.92MHz 1.113s < 5s Pass After Release the button, EUT emission Continue 1.113 seconds FCC ID: SFB-HR135 Page 21 of 29

Report No.: STI130123026 FCC ID: SFB-HR135 Page 22 of 29

Report No.: STI130123026 9 Band Edge Check 9.1 Test limit Please refer section15.231 and section 15.205. Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. 9.2 Test Procedure 11.2.1 Put the EUT on a 0.8m high table, power on the EUT. Emissions were scanned and measured rotating the EUT to 360 degrees, Find the maximum Emission 11.2.2 Turning to Low and High frequency, then reduced 50dB from the reference level. The reference level is the level of the highest amplitude signal observed from the transmitter at the fundamental frequency. 11.2.3 Check the spurious emissions out of band. 11.2.4 RBW, VBW Setting, please see the following test plot. 9.3 Test Setup Same to 5.2 9.4 Test Result The Restricted bands is 399.9-410MHz and 608-614MHz, The EUT operation frequency is 433.92MHz, The test is not applicable. FCC ID: SFB-HR135 Page 23 of 29

Report No.: STI130123026 10 Antenna Requirement 10.1 Standard Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 10.2 Antenna Connected Construction The directional gains of antenna used for transmitting is 0 dBi, and the antenna connector is de- signed with permanent attachment and no consideration of replacement. Please see EUT photo for details. 10.3 Result The EUT antenna is PCB antenna a. It comply with the standard requirement. FCC ID: SFB-HR135 Page 24 of 29

Report No.: STI130123026 11 Photographs of Test Setup Photographs-Radiated Emission Test Setup in Chamber FCC ID: SFB-HR135 Page 25 of 29

Report No.: STI130123026 12 Photographs of EUT FCC ID: SFB-HR135 Page 26 of 29

Report No.: STI130123026 FCC ID: SFB-HR135 Page 27 of 29

Report No.: STI130123026 FCC ID: SFB-HR135 Page 28 of 29

Report No.: STI130123026 -------END OF THE REPORT------- FCC ID: SFB-HR135 Page 29 of 29


Document Created: 2013-03-18 16:45:37
Document Modified: 2013-03-18 16:45:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC