Test Report

FCC ID: SF4-ATI5726

Test Report

Download: PDF
FCCID_1289678

ATI Electronics (ShenZhen) Co., LTD Model: 5726 FCC Part 15C Measurement and Test Report For ATI Electronics (ShenZhen) Co., Ltd 2/F, A Tower, Tangyanshan Industrial Park Tangkeng Village, Shiyan Town Shenzhen, China FCC ID: SF4-ATI5726 Report Concerns: Equipment Type: Original Report Wiimote Model: 5726 Report No.: STR10058101I Test Date: 2010-05-17 to 2010-05-31 Issue Date: 2010-06-01 Test Engineer: Seven Song Reviewed By: Lahm Peng Approved & Authorized By: Jandy so/PSQ Manager Prepared By: SEM.Test Compliance Service Co., Ltd 3/F, Jinbao Commerce Building, Xin'an Fanshen Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by SEM.Test Compliance Service Co., Ltd. REPORT NO.: STR10058101I PAGE 1 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 TABLE OF CONTENTS 1. GENERAL INFORMATION...................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)...............................................................................3 1.2 TEST STANDARDS...................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S) .......................................................................................................................3 1.4 TEST METHODOLOGY .............................................................................................................................................4 1.5 TEST FACILITY .......................................................................................................................................................4 1.6 EUT EXERCISE SOFTWARE ....................................................................................................................................4 1.7 ACCESSORIES EQUIPMENT LIST AND DETAILS .......................................................................................................4 1.8 EUT CABLE LIST AND DETAILS .............................................................................................................................4 2. SUMMARY OF TEST RESULTS ...........................................................................................................................5 3. §15.203 - ANTENNA REQUIREMENT..................................................................................................................6 3.1 STANDARD APPLICABLE.........................................................................................................................................6 3.2 TEST RESULT..........................................................................................................................................................6 4. NUMBER OF HOPPING CHANNELS AND CHANNEL SPACING .................................................................7 4.1 STANDARD APPLICABLE.........................................................................................................................................7 4.2 TEST EQUIPMENT LIST AND DETAILS .....................................................................................................................7 4.3 TEST PROCEDURE ...................................................................................................................................................7 4.4 ENVIRONMENTAL CONDITIONS ..............................................................................................................................7 4.5 SUMMARY OF TEST RESULTS/PLOTS ......................................................................................................................8 5. DWELL TIME OF A HOPPING CHANNEL ......................................................................................................10 5.1 STANDARD APPLICABLE.......................................................................................................................................10 5.2 TEST EQUIPMENT LIST AND DETAILS ...................................................................................................................10 5.3 TEST PROCEDURE .................................................................................................................................................10 5.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................10 5.5 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................11 6. 20-DB BANDWIDTH..............................................................................................................................................13 6.1 STANDARD APPLICABLE.......................................................................................................................................13 6.2 TEST EQUIPMENT LIST AND DETAILS ...................................................................................................................13 6.3 TEST PROCEDURE .................................................................................................................................................13 6.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................13 6.5 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................13 7. POWER OUTPUT...................................................................................................................................................16 7.1 STANDARD APPLICABLE.......................................................................................................................................16 7.2 TEST EQUIPMENT LIST AND DETAILS ...................................................................................................................16 7.3 TEST PROCEDURE .................................................................................................................................................16 7.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................16 7.5 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................16 8. FIELD STRENGTH OF SPURIOUS EMISSIONS .............................................................................................17 8.1 MEASUREMENT UNCERTAINTY ............................................................................................................................17 8.2 STANDARD APPLICABLE.......................................................................................................................................17 8.3 TEST EQUIPMENT LIST AND DETAILS ...................................................................................................................18 8.4 TEST PROCEDURE .................................................................................................................................................18 8.5 CORRECTED AMPLITUDE & MARGIN CALCULATION ............................................................................................19 8.6 ENVIRONMENTAL CONDITIONS ............................................................................................................................19 8.7 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................19 9. OUT OF BAND EMISSIONS.................................................................................................................................27 9.1 STANDARD APPLICABLE.......................................................................................................................................27 9.2 TEST EQUIPMENT LIST AND DETAILS ...................................................................................................................27 9.3 TEST PROCEDURE .................................................................................................................................................27 9.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................27 9.5 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................28 REPORT NO.: STR10058101I PAGE 2 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Client Information Applicant: ATI Electronics (ShenZhen) Co., LTD Address of applicant: 2/F, A Tower, Tangyanshan Industrial Park Tangkeng Village, Shiyan Town Shenzhen, China Manufacturer: ATI Electronics (ShenZhen) Co., LTD Address of manufacturer: 2/F, A Tower, Tangyanshan Industrial Park Tangkeng Village, Shiyan Town Shenzhen, China General Description of E.U.T Items Description EUT Description: Wiimote Trade Name: / Model No.: 5726 Rated Voltage: Battery 3V Max. Output Power -6~4 dBm Frequency range: 2402-2480MHz Number of channels: 79 Channel Separation: 1MHz Type of Antenna: Integral Antenna Size: 14.8x3.2x3.6cm Note: The test data is gathered from a production sample, provided by the manufacturer. 1.2 Test Standards The following report is prepared on behalf of the ATI Electronics (ShenZhen) Co., LTD in accordance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.207, 15.209 and 15.247 of the Federal Communication Commissions rules. The objective is to determine compliance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.207, 15.209 and 15.247 of the Federal Communication Commissions rules. Maintenance of compliance is the responsibility of the manufacturer. Any modification of the product, which result in lowering the emission, should be checked to ensure compliance has been maintained. 1.3 Related Submittal(s)/Grant(s) No Related Submittal(s). REPORT NO.: STR10058101I PAGE 3 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 1.4 Test Methodology All measurements contained in this report were conducted with ANSI C63.4-2003, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. The equipment under test (EUT) was configured to measure its highest possible emission level. The test modes were adapted with Low Channel, Middle Channel and High Channel, accordingly in reference to the Operating Instructions. 1.5 Test Facility • FCC – Registration No.: 994117 SEM.Test Compliance Services Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files and the Registration is 994117. • Industry Canada (IC) Registration No.: 7673A The 3m Semi-anechoic chamber of SEM.Test Compliance Services Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 7673A. 1.6 EUT Exercise Software The EUT exercise program used during the testing was designed to exercise the system components. 1.7 Accessories Equipment List and Details Manufacturer Description Model Serial Number Notebook ASUS XR55 / 1.8 EUT Cable List and Details Cable Description Length (M) Shielded/Unshielded With Core/Without Core / / / / REPORT NO.: STR10058101I PAGE 4 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 2. SUMMARY OF TEST RESULTS FCC RULES DESCRIPTION OF TEST RESULT §15.203;§15.247(b)(4)(i) Antenna Requirement Compliant §15.247(a)(1)(iii) Quantity of Hopping Channel Compliant §15.247(a)(1) Channel Separation Compliant §15.247(a)(1)(iii) Time of Occupancy (Dwell time) Compliant §15.247(a) 20dB Bandwidth Compliant §15.247(b)(1) Power Output Compliant §15.209(a)(f) Radiated Emission Compliant §15.247(c) Band edge Compliant REPORT NO.: STR10058101I PAGE 5 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 3. §15.203 - ANTENNA REQUIREMENT 3.1 Standard Applicable According to FCC 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. 3.2 Test Result This product has a permanent antenna, fulfill the requirement of this section. REPORT NO.: STR10058101I PAGE 6 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 4. NUMBER OF HOPPING CHANNELS AND CHANNEL SPACING 4.1 Standard Applicable According to FCC 15.247(a)(1), frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 kHz or two-thirds of the 20 dB bandwidth of the hopping channel, and frequency hopping systems in the 2400-2483.5 MHz band shall use at least 15 channels. 4.2 Test Equipment List and Details Manufacturer Description Model Serial Number Cal. Date Due. Date Aglient Spectrum Analyzer E4402B-ESA US41192821 2009-08-12 2010-08-11 Trilog Broadband SCHWARZBECK VULB9163 9163-333 2009-07-21 2010-07-20 Antenna Statement of Traceability: All calibrations have been performed per the NVLAP requirements traceable to the NIST. 4.3 Test Procedure Set the Lowest channel to the Highest Channel, observed the band of 2400MHz to 2438.5MHz, than count it out the number of channels for comparing with the FCC rules. Adjust channel spacing can be read by adjusting the Analyzer SPAN. 4.4 Environmental Conditions Temperature: 25 °C Relative Humidity: 54% ATM Pressure: 1011 mbar REPORT NO.: STR10058101I PAGE 7 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 4.5 Summary of Test Results/Plots No. of Channel=79 Channel Spacing (Low CH=1MHz) REPORT NO.: STR10058101I PAGE 8 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 Channel Spacing (Middle CH=1MHz) Channel Spacing (High CH=1MHz) REPORT NO.: STR10058101I PAGE 9 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 5. DWELL TIME OF A HOPPING CHANNEL 5.1 Standard Applicable According to 15.247(a)(1)(iii), Frequency hopping systems in the 2400–2483.5 MHz band shall use at least 15 channels. The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. 5.2 Test Equipment List and Details Manufacturer Description Model Serial Number Cal. Date Due. Date Aglient Spectrum Analyzer E4402B-ESA US41192821 2009-08-12 2010-08-11 Trilog Broadband SCHWARZBECK VULB9163 9163-333 2009-07-21 2010-07-20 Antenna Statement of Traceability: All calibrations have been performed per the NVLAP requirements traceable to the NIST. 5.3 Test Procedure 1. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 2. Set center frequency of spectrum analyzer = operating frequency. 3. Set the spectrum analyzer as RBW, VBW=100KHz, Span = 0Hz. 4. Repeat above procedures until all frequency measured was complete. 5.4 Environmental Conditions Temperature: 26 °C Relative Humidity: 54% ATM Pressure: 1011 mbar REPORT NO.: STR10058101I PAGE 10 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 5.5 Summary of Test Results/Plots The dwell time within a 31.6 second period in data mode is independent from the packet type (packet length). The calculation for a 31.6 second period is a follows: Dwell time = time slot length * hop rate / number of hopping channels *31.6s Test data is corrected with the worse case, which the packet length is DH1. CH Low: DH1 time slot = 0.390(ms) * (1600/(79)) * 31.6 = 249.6 (ms) < 400 (ms) REPORT NO.: STR10058101I PAGE 11 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 CH Mid: DH1 time slot = 0.400 (ms) * (1600/(79)) * 31.6 = 256.0 (ms) < 400 (ms) CH High: DH1 time slot = 0.390(ms) * (1600/(79)) * 31.6 = 249.6 (ms) < 400 (ms) REPORT NO.: STR10058101I PAGE 12 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 6. 20-dB BANDWIDTH 6.1 Standard Applicable According to 15.247(a)(1)(iii). For frequency hopping systems operating in the 2400MHz-2483.5 MHz no limit for 20dB bandwidth. 6.2 Test Equipment List and Details Manufacturer Description Model Serial Number Cal. Date Due. Date Aglient Spectrum Analyzer E4402B-ESA US41192821 2009-08-12 2010-08-11 Trilog Broadband SCHWARZBECK VULB9163 9163-333 2009-07-21 2010-07-20 Antenna Statement of Traceability: All calibrations have been performed per the NVLAP requirements traceable to the NIST. 6.3 Test Procedure 1. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 2. Set center frequency of spectrum analyzer = operating frequency. 3. The spectrum analyzer as RBW=10KHz (1 % of Bandwidth.), Sweep=auto 4. Mark the peak frequency and –20dB (upper and lower) frequency. 6.4 Environmental Conditions Temperature: 25 °C Relative Humidity: 53% ATM Pressure: 1018 mbar 6.5 Summary of Test Results/Plots Frequency 20 dB Bandwidth Limit MHz kHz dB 2402 369.1 / 2441 364.1 / 2480 359.1 / REPORT NO.: STR10058101I PAGE 13 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 Channel Bandwidth (CH Low): Channel Bandwidth (CH Mid): REPORT NO.: STR10058101I PAGE 14 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 Channel Bandwidth (CH High): REPORT NO.: STR10058101I PAGE 15 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 7. POWER OUTPUT 7.1 Standard Applicable According to 15.247(b)(1). For frequency hopping systems operating in the 2400–2483.5 MHz band employing at least 75 non-overlapping hopping channels, and all frequency hopping systems in the 5725–5850 MHz band: 1 watt. For all other frequency hopping systems in the 2400–2483.5 MHz band: 0.125 watts. 7.2 Test Equipment List and Details Serial Description Manufacturer Model Cal. Date Due. Date Number Spectrum ROHDE&SCHWARZ FSEA20 DE25181 2009-08-12 2010-08-11 Analyzer Positioning C&C CC-C-1F N/A 2009-08-12 2010-08-11 Controller Trilog Broadband SCHWARZBECK VULB9163 9163-333 2009-07-21 2010-07-20 Antenna Horn Antenna SCHWARZBECK BBHX 9120 9120-426 2009-07-21 2010-07-20 RF Switch EM EMSW18 SW060023 2009-08-12 2010-08-11 Amplifier Agilent 8447F 3113A06717 2009-08-12 2010-08-11 Coaxial Cable SCHWARZBECK AK9513 9513-10 2009-08-12 2010-08-11 EMI Test ROHDE&SCHWARZ ESPI 25498514 2009-08-12 2010-08-11 Receiver Statement of Traceability: All calibrations have been performed per the NVLAP requirements traceable to the NIST. 7.3 Test Procedure The device under test has an integral antenna and the power was measured on a radiated basis. 7.4 Environmental Conditions Temperature: 24 °C Relative Humidity: 55% ATM Pressure: 1011 mbar 7.5 Summary of Test Results/Plots 2402 MHz 1.6596 mW EIRP 2441 MHz 1.6218 mW EIRP 2480 MHz 1.5849 mW EIRP Note: The Antenna Gain is under considering. REPORT NO.: STR10058101I PAGE 16 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 8. FIELD STRENGTH OF SPURIOUS EMISSIONS 8.1 Measurement Uncertainty Based on NIS 81, The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of a radiation emissions measurement is +5.1 dB. 8.2 Standard Applicable According to §15.247(c), 15.205 15.209(b) &15.35 (b), the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Section 15.209: 30 - 88 MHz 40 dBuV/m @3M 88 -216 MHz 43.5 dBuV/m @3M 216 -960 MHz 46 dBuV/m @3M Above 960 MHz 54dBuV/m @3M The emission limit in this paragraph is based on measurement instrumentation employing an average detector. The provisions in §15.35 for limiting peak emissions apply. EMISSIONS RADIATED OUTSIDE OF THE SPECIFIED FREQUENCY BANDS, EXCEPT FOR HARMONICS, SHALL BE ATTENUATED BY AT LEAST 20 dB BELOW THE LEVEL OF THE FUNDAMENTAL OR TO THE GENERAL RADIATED EMISSION LIMITS IN 15.209,WHICHEVER IS THE LESSER ATTENUATION. Emissions that fall in the restricted bands (15.205) must be less than 54dBuV/m otherwise the spurious and harmonics must be attenuated by at least 20dB. REPORT NO.: STR10058101I PAGE 17 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 8.3 Test Equipment List and Details Serial Description Manufacturer Model Cal. Date Due. Date Number Spectrum ROHDE&SCHWARZ FSEA20 DE25181 2009-08-12 2010-08-11 Analyzer Positioning C&C CC-C-1F N/A 2009-08-12 2010-08-11 Controller Trilog Broadband SCHWARZBECK VULB9163 9163-333 2009-07-21 2010-07-20 Antenna Horn Antenna SCHWARZBECK BBHX 9120 9120-426 2009-07-21 2010-07-20 RF Switch EM EMSW18 SW060023 2009-08-12 2010-08-11 Amplifier Agilent 8447F 3113A06717 2009-08-12 2010-08-11 Coaxial Cable SCHWARZBECK AK9513 9513-10 2009-08-12 2010-08-11 EMI Test ROHDE&SCHWARZ ESPI 25498514 2009-08-12 2010-08-11 Receiver Statement of Traceability: All calibrations have been performed per the NVLAP requirements traceable to the NIST. 8.4 Test Procedure The setup of EUT is according with per ANSI C63.4-2003 measurement procedure. The specification used was with the FCC Part 15.205 15.247(a) and FCC Part 15.209 Limit. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. Antenna Tower 1m-4m 3m EUT 0.8m Turntable Table To EMI Receiver Ground Plane REPORT NO.: STR10058101I PAGE 18 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 8.5 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and the Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading + Ant. Factor + Cable Loss – Ampl. Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -6dBμV means the emission is 6dBμV below the maximum limit for Class B. The equation for margin calculation is as follows: Margin = Corr. Ampl. – FCC Part 15 Limit 8.6 Environmental Conditions Temperature: 25 °C Relative Humidity: 52% ATM Pressure: 1012 mbar 8.7 Summary of Test Results/Plots According to the data below, the FCC Part 15.205, 15.209 and 15.247 standards, and had the worst margin of: -1.3 dBμV at 675.2079 MHz in the Vertical polarization for Middle Channel, 30 MHz to 25 GHz, 3 Meters REPORT NO.: STR10058101I PAGE 19 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 Meter Antenna Correction Frequency Direction Polar Cable loss Amplifier Limit Margin Detector Reading Loss Amplitude MHz Degree H/V dB dB dBuV/m dB dBuV dB dBuV/m Low Channel (1G to 25GHz) 4804.0 AV 42.2 57 H 34.1 5.2 33.0 48.5 54 -5.5 4804.0 AV 41.0 35 V 34.1 5.2 33.0 47.3 54 -6.7 7206.0 AV 34.1 60 H 37.4 6.1 33.5 44.1 54 -9.9 7206.0 AV 29.9 79 V 37.4 6.1 33.5 39.9 54 -14.1 4804.0 PK 48.3 65 H 37.4 6.1 33.5 58.3 74 -15.7 4804.0 PK 45.8 98 V 34.1 5.2 33.0 52.1 74 -21.9 7206.0 PK 45.6 256 H 34.1 5.2 33.0 51.9 74 -22.1 7206.0 PK 38.5 185 V 37.4 6.1 33.5 48.5 74 -25.5 Middle Channel (1G to 25GHz) 4882.0 AV 43.0 21 H 34.1 5.2 33.0 49.3 54 -4.7 4882.0 AV 41.3 34 V 34.1 5.2 33.0 47.6 54 -6.4 7323.0 AV 34.4 342 H 37.4 6.1 33.5 44.4 54 -9.6 7323.0 AV 33.9 30 V 37.4 6.1 33.5 43.9 54 -10.1 4882.0 PK 48.5 237 H 37.4 6.1 33.5 58.5 74 -15.5 4882.0 PK 44.7 354 V 37.4 6.1 33.5 54.7 74 -19.3 7323.0 PK 45.1 264 H 34.1 5.2 33.0 51.4 74 -22.6 7323.0 PK 42.9 187 V 34.1 5.2 33.0 49.2 74 -24.8 High Channel (1G to 25GHz) 4960.0 AV 40.2 17 H 37.4 6.1 33.5 50.2 54 -3.8 4960.0 AV 38.7 13 V 37.4 6.1 33.5 48.7 54 -5.3 7440.0 AV 39.3 355 H 34.1 5.2 33.0 45.6 54 -8.4 7440.0 AV 35.2 66 V 34.1 5.2 33.0 41.5 54 -12.5 4960.0 PK 52.2 50 H 34.1 5.2 33.0 58.5 74 -15.5 4960.0 PK 48.5 59 V 34.1 5.2 33.0 54.8 74 -19.2 7440.0 PK 40.3 269 H 37.4 6.1 33.5 50.3 74 -23.7 7440.0 PK 37.4 64 V 37.4 6.1 33.5 47.4 74 -26.6 Note: Testing is carried out with frequency rang 30MHz to the tenth harmonics, which above 5th Harmonics is close to the noise base even antenna close up to 1meter distance according the measurement of ANSI C63.4. REPORT NO.: STR10058101I PAGE 20 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 From 30 MHz to 1 GHz (Low Channel) Horizontal No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) ( ·) (cm) 1 289.0021 32.18 8.54 40.72 46.00 -5.28 132 100 QP 2 337.2155 34.24 9.18 43.42 46.00 -2.58 224 100 QP 3 361.7139 33.77 9.67 43.44 46.00 -2.56 176 110 QP 4 385.2805 31.87 9.96 41.83 46.00 -4.17 98 105 QP REPORT NO.: STR10058101I PAGE 21 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 Vertical No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) ( ·) (cm) 1 192.4186 30.53 5.66 36.19 43.50 -7.31 328 100 QP 2 554.8254 27.13 13.61 40.74 46.00 -5.26 165 110 QP 3 651.9417 29.26 14.35 43.61 46.00 -2.39 82 117 QP 4 675.2080 27.79 14.42 42.21 46.00 -3.79 197 100 QP REPORT NO.: STR10058101I PAGE 22 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 From 30 MHz to 1 GHz (Middle Channel) Horizontal No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) ( ·) (cm) 1 192.4185 33.48 5.66 39.14 43.50 -4.36 134 100 QP 2 337.2155 35.24 9.18 44.42 46.00 -1.58 187 120 QP 3 385.2805 33.37 9.96 43.33 46.00 -2.67 245 100 QP REPORT NO.: STR10058101I PAGE 23 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 Vertical No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) ( ·) (cm) 1 192.4185 28.89 5.66 34.55 40.00 -5.45 267 100 QP 2 675.2079 31.28 14.42 45.70 47.00 -1.30 165 100 QP 3 724.2611 28.88 14.74 43.62 47.00 -3.38 321 122 QP REPORT NO.: STR10058101I PAGE 24 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 From 30 MHz to 1 GHz (High Channel) Horizontal No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) ( ·) (cm) 1 289.0020 35.18 8.54 43.72 46.00 -2.28 137 100 QP 2 337.2155 33.74 9.18 42.92 46.00 -3.08 224 115 QP 3 361.7139 34.77 9.67 44.44 46.00 -1.56 67 107 QP 4 385.2805 34.37 9.96 44.33 46.00 -1.67 80 100 QP REPORT NO.: STR10058101I PAGE 25 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 Vertical No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) ( ·) (cm) 1 361.7139 31.39 9.67 41.06 47.00 -5.94 137 100 QP 2 651.9416 30.95 14.35 45.30 47.00 -1.70 274 100 QP 3 675.2079 30.28 14.42 44.70 47.00 -2.30 133 109 QP REPORT NO.: STR10058101I PAGE 26 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 9. OUT OF BAND EMISSIONS 9.1 Standard Applicable According to §15.247 (d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. 9.2 Test Equipment List and Details Serial Description Manufacturer Model Cal. Date Due. Date Number Spectrum ROHDE&SCHWARZ FSEA20 DE25181 2009-08-12 2010-08-11 Analyzer Positioning C&C CC-C-1F N/A 2009-08-12 2010-08-11 Controller Trilog Broadband SCHWARZBECK VULB9163 9163-333 2009-07-21 2010-07-20 Antenna Horn Antenna SCHWARZBECK BBHX 9120 9120-426 2009-07-21 2010-07-20 RF Switch EM EMSW18 SW060023 2009-08-12 2010-08-11 Amplifier Agilent 8447F 3113A06717 2009-08-12 2010-08-11 Coaxial Cable SCHWARZBECK AK9513 9513-10 2009-08-12 2010-08-11 EMI Test ROHDE&SCHWARZ ESPI 25498514 2009-08-12 2010-08-11 Receiver Statement of Traceability: All calibrations have been performed per the NVLAP requirements traceable to the NIST. 9.3 Test Procedure 1. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 2. Set the spectrum analyzer as RBW, VBW=100KHz, Span=100MHz, Sweep = auto 3. Set the Lowest and Highest Transmitting Channel, observed the outside band of 2400MHz to 2438.5MHz, then mark the higher-level emission for comparing with the FCC rules. 9.4 Environmental Conditions Temperature: 23°C Relative Humidity: 54% ATM Pressure: 1011 mbar REPORT NO.: STR10058101I PAGE 27 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 9.5 Summary of Test Results/Plots Frequency Limit Test mode Result MHz dBuV /dB 2390.00 <54dBuv Pass Lowest 2400.00 >20dB Pass Highest 2483.50 <54dBuv Pass The edge emissions are below the FCC 15.209 Limits. Please refer to the test plots below. Lowest Bandedge No. Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV/m) Factor(dB) (dBuV/m) (dBuV/m) (dB) 1 2390.000 12.17 35.59 47.76 54.00 -6.24 Average Detector 2390.000 20.65 35.59 56.24 74.00 -17.76 Peak Detector 2 2400.000 22.23 35.68 57.91 / / Average Detector 3 2402.000 47.47 35.69 83.16 / / Average Detector REPORT NO.: STR10058101I PAGE 28 OF 29 FCC PART 15.247

ATI Electronics (ShenZhen) Co., LTD Model: 5726 Highest Bandedge No. Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV/m) Factor(dB) (dBuV/m) (dBuV/m) (dB) 1 2483.500 13.68 35.97 49.65 54.00 -4.35 Average Detector 2483.500 27.54 35.97 63.51 74.00 -10.49 Peak Detector ***** END OF REPORT ***** REPORT NO.: STR10058101I PAGE 29 OF 29 FCC PART 15.247


Document Created: 2010-06-01 17:03:45
Document Modified: 2010-06-01 17:03:45
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC