Declaration Letter

FCC ID: S96SMART

Cover Letter(s)

Download: PDF

  Modular Approval Request FCC (Per DA 00-1407)                           FCC ID: S96SMART

  Items to be covered                                                                            Answer From
                                                                                                 Applicant

  1. The modular transmitter must have its own RF shielding.                                     Yes

  2. The modular transmitter must have buffered modulation/data inputs (if such inputs are       Yes
  provided) to ensure that the module will comply with Part 15 requirements under
  conditions of excessive data rates or over-modulation.
  3. The modular transmitter must have its own power supply regulation.                          Yes

  4. The modular transmitter must comply with the antenna requirements of Section 15.203         Yes
  and 15.204(c). The antenna must either be permanently attached or employ a "unique"
  antenna coupler (at all connections between the module and the antenna, including the
  cable).
  5. The modular transmitter must be tested in a stand-alone configuration, i.e., the            Yes
  module must not be inside another device during testing. This is intended to demonstrate
  that the module is capable of complying with Part 15 emission limits regardless of the
  device into which it is eventually installed.
  6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID      Yes
  is not visible when the module is installed inside another device, then the outside of
  the device into which the module is installed must also display a label referring to the
  enclosed module. This exterior label can use wording such as the following: "Contains
  Transmitter Module FCC ID: XYZMODEL1" or "Contains FCC ID: XYZMODEL1." Any similar
  wording that expresses the same meaning may be used. The Grantee may either provide such
  a label, an example of which must be included in the application for equipment
  authorization, or, must provide adequate instructions along with the module which explain
  this requirement. In the latter case, a copy of these instructions must be included in
  the application for equipment authorization.



  7. The modular transmitter must comply with any specific rule or operating requirements        Yes
  applicable to the transmitter and the manufacturer must provide adequate instructions
  along with the module to explain any such requirements. A copy of these instructions must
  be included in the application for equipment authorization. For example, there are very
  strict operational and timing requirements that must be met before a transmitter is
  authorized for operation under Section 15.231. For instance, data transmission is
  prohibited, except for operation under Section 15.231(e), in which case there are
  separate field strength level and timing requirements. Compliance with these
  requirements must be assured.

  8. The modular transmitter must comply with any applicable RF exposure requirements. For       Yes
  example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15,including
  15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and
  millimeter wave devices perform routine environmental evaluation for RF Exposure to
  demonstrate compliance. In addition, spread spectrum transmitters operating under
  Section 15.247 are required to address RF Exposure compliance in accordance with Section
  15.247(b)(4). Modular transmitters approved under other Sections of Part 15,when
  necessary, may also need to address certain RF Exposure concerns, typically by providing
  specific installation and operating instructions for users, installers and other
  interested parties to ensure compliance.
Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be
possible to obtain a “Limited Modular Approval” (LMA).



___________________________

Company Name: Xiamen Intretech Inc.
Contact Name: Frank Jiang
Title of Person: QA section Manager
Address: No.588.Jiahe Road,Xiamen,Fujian,China 361006



Document Created: 2019-04-01 10:06:56
Document Modified: 2019-04-01 10:06:56

© 2019 FCC.report
This site is not affiliated with or endorsed by the FCC