TEST REPORT

FCC ID: S7APARANIESD200

Test Report

Download: PDF
FCCID_707063

Ref. No.: LR500110608T 243 Jubug-Ri,Yangji-Myeon, Yongin-Si, Gyeonggi-Do, Korea 449-822 Tel: +82-31-323-6008 Fax: +82-31-323-6010 http://www.ltalab.com Dates of Tests: August 11 ~ 17, 2006 Test Report S/N: LR500110608T Test Site : LTA CO., LTD. CERTIFICATIO OF COMPLIANCE FCC ID. S7APARANIESD200 APPLICANT Sena Technologies, Inc. FCC Classification : FHSS Sequence Spread Spectrum (FHSS) Manufacturing Description : Bluetooth Serial Adaptor Manufacturer : Sena Technologies, Inc. Model name : Parani-ESD200 Test Device Serial No.: : Identification Rule Part(s) : FCC Part 15.247 Subpart C; ANSI C-63.4-2003 Frequency Range : 2402 ~ 2480MHz RF power : 4.35dBm - Conducted Data of issue : August 18, 2006 This test report is issued under the authority of: The test was supervised by: Dong –Min JUNG, Technical Manager Kyung-Taek LEE, Test Engineer This test result only responds to the tested sample. It is not allowed to copy this report even partly without the allowance of the test laboratory. This report must not be used by the applicant to claim product endorsement by any agency. NVLAP LAB Code.: 200723-0 Copyright ○ c 2006, LTA Co., Ltd. Page 1 of 28

Ref. No.: LR500110608T TABLE OF CONTENTS 1. GENERAL INFORMATION’S -------------------------------------------------------------------------- 3 2. INFORMATION’S ABOUT TEST ITEM ------------------------------------------------------------- 4 3. TEST REPORT --------------------------------------------------------------------------------------------- 5 3.1 SUMMARY OF TESTS ------------------------------------------------------------------------------ 5 3.2 TECHNICAL CHARACTERISTICS TEST ------------------------------------------------------- 6 3.2.1 CARRIER FREQUENCY SEPARATION ---------------------------------------------------- 6 3.2.2 NUMBER OF HOPPING FREQUENCIES -------------------------------------------------- 8 3.2.3 20 dB BANDWIDTH ---------------------------------------------------------------------------- 11 3.2.4 TIME OF OCCUPANCY (Dwell Time) ------------------------------------------------------- 13 3.2.5 TTANSMITTER OUTPUT POWER ---------------------------------------------------------- 15 3.2.6 BAND - EDGE ----------------------------------------------------------------------------------- 17 3.2.7 FIELD STRENGTH OF HARMONICS ------------------------------------------------------ 26 APPENDIX APPENDIX TEST EQUIPMENT USED FOR TESTS -------------------------------------------- 27 Copyright ○ c 2006, LTA Co., Ltd. Page 2 of 28

Ref. No.: LR500110608T 1. General information’s 1-1 Test Performed Company name : LTA Co., Ltd. Address : 243, Jubug-ri,Yangji-Myeon,Youngin-Si, Kyunggi-Do, Korea. 449-822 Web site : http://www.ltalab.com E-mail : chahn@ltalab.com Telephone : +82-31-323-6008 Facsimile +82-31-323-6010 Quality control in the testing laboratory is implemented as per ISO/IEC 17025 which is the “General requirements for the competents of calibration and testing laboratory”. 1-2 Accredited agencies LTA Co., Ltd. is approved to perform EMC testing by the following agencies: Agency Country Accreditation No. Validity Reference NVLAP U.S.A 200723-0 2006-09-30 ECT accredited Lab. RRL KOREA KR0049 2007-07-13 EMC accredited Lab. FCC U.S.A 610755 2008-03-28 FCC filing VCCI JAPAN R2133, C2307 2008-06-22 VCCI registration IC CANADA IC5799 2008-04-23 IC filing Copyright ○ c 2006, LTA Co., Ltd. Page 3 of 28

Ref. No.: LR500110608T 2. Information’s about test item 2-1 Client & Manufacturer Company name : Sena Technologies, Inc. Address : 210 Yangjae-dong Seocho-gu Seoul 137-130 Korea TEL / FAX : +82-2-571-8283/ +82-2-573-7710 2-2 Equipment Under Test (EUT) Trade name : Bluetooth Serial Adaptor FCC ID : S7APARANIESD200 Model name : Parani-ESD200 Serial number : Identification Date of receipt : August 11, 2006 EUT condition : Pre-production, not damaged Antenna type : Chip antenna Max Gain 3.95dBi Frequency Range : 2402 ~ 2480MHz RF output power : 4.35dBm (Class 2) - Conducted Number of channels : 79 Channel spacing : 1MHz Channel Access Protocol : Frequency Hopping Type of Modulation : GFSK Power Source : 3.3V 2-3 Tested frequency LOW MID HIGH Frequency (MHz) 2402 2441 2480 2-4 Ancillary Equipment Equipment Model No. Serial No. Manufacturer Mouse MO56UO 510022473 DELL Notebook Latitude D505 8N29F1S DELL Bluetooth Jig N/A N/A SENA Copyright ○ c 2006, LTA Co., Ltd. Page 4 of 28

Ref. No.: LR500110608T 3. Test Report 3.1 Summary of tests FCC Part Test Status Parameter Limit Section(s) Condition (note 1) 15.247(a) Carrier Frequency Separation > 25 kHz C 15.247(a) Number of Hopping Frequencies > 75 hops C 15.247(a) 20 dB Bandwidth < 1 MHz C 15.247 Dwell Time < 0.4 seconds Conducted C 15.247(b) Transmitter Output Power < 1Watt C 15.247(d) Conducted Spurious emission > 20 dBc C 15.247(d) Band Edge > 20 dBc C < 54 dBuV 15.249 / 15.209 Field Strength of Harmonics Radiated C (at 3m) 15.207 /15.107 AC Conducted Emissions EN 55022 Line Conducted NA Note 1: C=Complies NC=Not Complies NT=Not Tested NA=Not Applicable Note 2: The data in this test report are traceable to the national or international standards. The sample was tested according to the following specification: FCC Parts 15.247; ANSI C-63.4-2003 Copyright ○ c 2006, LTA Co., Ltd. Page 5 of 28

Ref. No.: LR500110608T 3.2 Transmitter requirements 3.2.1 Carrier Frequency Separation Procedure: The carrier frequency separation was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function enabled. After the trace being stable, the reading value between the peaks of the adjacent channels using the marker-delta function was recorded as the measurement results. The spectrum analyzer is set to: Span = 3 MHz (wide enough to capture the peaks of two adjacent channels) RBW = 30 kHz (1% of the span or more) Sweep = auto VBW = 30 kHz Detector function = peak Trace = max hold Measurement Data: Test Results Carrier Frequency Separation (MHz) Result 1.005 Complies - See next pages for actual measured spectrum plots. Minimum Standard: The EUT shall have hopping channel carrier frequencies separated by a minimum of 25kHz or the 20dB bandwidth of the hopping channel, whichever is greater. Measurement Setup EUT Spectrum Analyzer Coax cable Figure 1: Measurement setup for the carrier frequency separation Copyright ○ c 2006, LTA Co., Ltd. Page 6 of 28

ar ferrorsr—csozce n i x uo5 ie NWV oo at 2e se "he"d rerw vee 1 M oren + ds un se S1rl cora cenmee z:zzze00 ons seur ahes"dd to un vou ao ane She sugee 2000 mz Vise ®

Ref. No.: LR500110608T 3.2.2 Number of Hopping Frequencies Procedure: The number of hopping frequencies was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function enabled. To get higher resolution, four frequency ranges within the 2400 ~ 2483.5 MHz FH band were examined. The spectrum analyzer is set to: Frequency range 1: Start = 2389.5MHz, Stop = 2414.5 MHz 2: Start = 2414.5MHz, Stop = 2439.5 MHz 3: Start = 2439.5MHz, Stop = 2464.5 MHz 4: Start = 2464.5MHz, Stop = 2489.5 MHz RBW = 300 kHz (1% of the span or more) Sweep = auto VBW = 300 kHz (VBW ≥ RBW) Detector function = peak Trace = max hold Span = 25MHz Measurement Data: Complies Total number of Hopping Channels 79 - See next pages for actual measured spectrum plots. Minimum Standard: At least 75 hopes Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2006, LTA Co., Ltd. Page 8 of 28

Ref. No.: LR500110608T Number of Hopping Frequencies Copyright ○ c 2006, LTA Co., Ltd. Page 9 of 28

Ref. No.: LR500110608T Number of Hopping Frequencies Copyright ○ c 2006, LTA Co., Ltd. Page 10 of 28

Ref. No.: LR500110608T 3.2.3 20 dB Bandwidth Procedure: The bandwidth at 20 dB below the highest inband spectral density was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function disabled at the highest, middle and the lowest available channels.. After the trace being stable, Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 20dB down one side of the emission. Reset the marker-delta function, and move the marker to the other side of the emission, until it is ( as close as possible to ) even with the reference marker level. The marker-delta reading at this point is the 20 dB bandwidth of the emission. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest channels Span = 2 MHz (approximately 2 or 3 times of the 20 dB bandwidth) RBW = 30 kHz Sweep = auto VBW = 30 kHz (VBW ≥ RBW) Detector function = peak Trace = max hold Measurement Data: Frequency Test Results Channel No. (MHz) Measured Bandwidth (MHz) Result 2441 39 0.950 Complies - See next pages for actual measured spectrum plots. Minimum Standard: The transmitter shall have a maximum 20dB bandwidth of 1 MHz. Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2006, LTA Co., Ltd. Page 11 of 28

Ref. No.: LR500110608T 20 dB Bandwidth Copyright ○ c 2006, LTA Co., Ltd. Page 12 of 28

Ref. No.: LR500110608T 3.2.4 Time of Occupancy (Dwell Time) Procedure: The dwell time was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function enabled. The spectrum analyzer is set to: Center frequency = 2441 MHz Span = zero RBW = 1 MHz VBW = 1 MHz (VBW ≥ RBW) Trace = max hold Detector function = peak Measurement Data: Channel Test Results Channel Frequency Packet Type Number (MHz) Dwell Time (ms) Result DH 1 135.21 Complies 39 2441 DH 3 266.11 Complies DH 5 310.78 Complies - See next pages for actual measured spectrum plots. Minimum Standard: 0.4 seconds within a 30 second period per any frequency Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2006, LTA Co., Ltd. Page 13 of 28

Ref. No.: LR500110608T DH 1 DH 3 DH 5 Copyright ○ c 2006, LTA Co., Ltd. Page 14 of 28

Ref. No.: LR500110608T 3.2.5 Transmitter Output Power Procedure: The peak output power was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function disabled at the highest, middle and the lowest available channels.. After the trace being stable, Use the marker-to-peak function to set the marker to the peak of the emission. The indicated level is the peak output power. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest channels Span = 5 MHz (approximately 5 times of the 20 dB bandwidth) RBW = 1 MHz (greater than the 20dB bandwidth of the emission being measured) VBW = 1 MHz (VBW ≥ RBW) Detector function = peak Trace = max hold Sweep = auto Measurement Data: Frequency Test Results Ch. (MHz) dBm mW Result 2402 0 4.35 2.723 Complies 2441 39 4.28 2.679 Complies 2480 78 2.82 1.914 Complies - See next pages for actual measured spectrum plots. Minimum Standard: < 1W Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2006, LTA Co., Ltd. Page 15 of 28

Ref. No.: LR500110608T Peak Output Power Copyright ○ c 2006, LTA Co., Ltd. Page 16 of 28

Ref. No.: LR500110608T 3.2.6 Band - edge Procedure: The bandwidth at 20dB down from the highest inband spectral density is measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function disabled at the highest, middle and the lowest available channels. After the trace being stable, Use the marker-to-peak function to measure 20 dB down both sides of the intentional emission. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest channels RBW = 100 kHz VBW = 100 kHz Span = 10 MHz Detector function = peak Trace = max hold Sweep = auto Measurement Data: Complies - All conducted emission in any 100kHz bandwidth outside of the spread spectrum band was at least 20dB lower than the highest inband spectral density. Therefore the applying equipment meets the requirement. - See next pages for actual measured spectrum plots. Minimum Standard: > 20 dBc Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2006, LTA Co., Ltd. Page 17 of 28

Ref. No.: LR500110608T Band - edge (with Hopping) Copyright ○ c 2006, LTA Co., Ltd. Page 18 of 28

Ref. No.: LR500110608T Band - edge (without Hopping) Copyright ○ c 2006, LTA Co., Ltd. Page 19 of 28

Ref. No.: LR500110608T Band - edge (at 20 dB blow) – Low channel Frequency Range = 30 MHz ~ 10th harmonic. Copyright ○ c 2006, LTA Co., Ltd. Page 20 of 28

Ref. No.: LR500110608T Band - edge (at 20 dB blow) – Low channel Frequency Range = 30 MHz ~ 10th harmonics. - Continues Copyright ○ c 2006, LTA Co., Ltd. Page 21 of 28

Ref. No.: LR500110608T Band - edge (at 20 dB blow) – Mid channel Frequency Range = 30 MHz ~ 10th harmonic. Copyright ○ c 2006, LTA Co., Ltd. Page 22 of 28

Ref. No.: LR500110608T Band - edge (at 20 dB blow) – Mid channel Frequency Range = 30 MHz ~ 10th harmonics. - Continues Copyright ○ c 2006, LTA Co., Ltd. Page 23 of 28

Ref. No.: LR500110608T Band - edge (at 20 dB blow) – High channel Frequency Range = 30 MHz ~ 10th harmonic. Copyright ○ c 2006, LTA Co., Ltd. Page 24 of 28

Ref. No.: LR500110608T Band - edge (at 20 dB blow) – High channel Frequency Range = 30 MHz ~ 10th harmonics. - Continues Copyright ○ c 2006, LTA Co., Ltd. Page 25 of 28

Ref. No.: LR500110608T 3.2.7 Field Strength of Harmonics Procedure: The EUT was placed on a 0.8m high wooden table inside a shielded enclosure. An antenna was placed near the EUT and measurements of frequencies and amplitudes of field strengths were recorded for reference during final measurements. For final radiated testing, measurements were performed in OATS. Measurements were performed with the EUT oriented in 3 orthogonal axis and rotated 360 degrees to determine worst-case orientation for maximum emissions. The spectrum analyzer is set to: Center frequency = the worst channel Frequency Range = 30 MHz ~ 10th harmonic. RBW = 100 kHz ( 30MHz ~ 1 GHz) VBW ≥ RBW th = 1 MHz (1 GHz ~ 10 harmonic ) Span = 100 MHz Detector function = peak Trace = max hold Sweep = auto Measurement Data: Complies Low channel Mid channel High channel Frequency Level Frequency Level Frequency Level (MHz) (dBuV) (MHz) (dBuV) (MHz) (dBuV) - - - - - - No emissions were detected at a level greater than 10dB below limit. - - - - - - Measurement uncertainty ± 6 dB Minimum Standard: FCC Part 15.209(a) Frequency (MHz) Limit (uV/m) @ 3m 30 ~ 88 100 ** 88 ~ 216 150 ** 216 ~ 960 200 ** Above 960 500 ** Except as provided in 15.209(g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88MHz, 174-216MHz or 470-806MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g. 15.231 and 15.241. Copyright ○ c 2006, LTA Co., Ltd. Page 26 of 28

Ref. No.: LR500110608T APPENDIX TEST EQUIPMENT USED FOR TESTS Copyright ○ c 2006, LTA Co., Ltd. Page 27 of 28

Ref. No.: LR500110608T Description Model No. Serial No. Manufacturer Next Cal. Date 1 Spectrum Analyzer 8594E 3649A03649 HP Dec-06 2 Signal Generator 8657A 3430U02049 HP Dec-06 3 Attenuator (3dB) 8491A 37822 HP Dec-06 4 Attenuator (3dB) 8491A 28881 HP Dec-06 5 EMI Test Receiver ESVD 843748/001 R&S Dec-06 6 Spectrum Analyzer 8591E 3649A05888 HP Jan-07 7 Spectrum Analyzer 8563E 3425A02505 HP Jan-07 8 RF Amplifier 8447D 2949A02670 HP Jan-07 9 RF Amplifier 8447D 2439A09058 HP Jan-07 10 RF Amplifier 8449B 3008A02126 HP Jun-07 11 TRILOG Antenna VULB 9160 9160-3172 SCHWARZBECK Feb-07 12 Log.-Per. Antenna VULP 9118 9118 A 401 SCHWARZBECK Feb-07 13 Biconical Antenna BBA 9106 VHA 9103-2315 SCHWARZBECK Feb-07 14 Horn Antenna 3115 00055005 ETS LINDGREN Jun-07 15 Horn Antenna BBHA 9120D 0499 Schwarzbeck Jun-07 16 Hygro-Thermograph THB-36 0041557-01 ISUZU Feb-07 17 Splitter (BNC) ZFM-150 15542 Mini-Circuits - 18 Splitter (SMA) ZFSC-2-2500 SF617800326 Mini-Circuits - 19 Power Divider 11636A 6243 HP Apr-07 20 DC Power Supply 6622A 3448A03079 HP Apr-07 21 Attenuator (30dB) 8498A 1801A06689 HP Apr-07 22 Attenuator (10dB) 8491A 63196 HP Apr-07 23 Power Meter EPM-441A GB32481702 HP Apr-07 24 Power Sensor 8481A 2702A64048 HP Apr-07 25 Audio Analyzer 8903B 3729A18901 HP May-07 26 Modulation Analyzer 8901B 3749A05878 HP May-07 27 Dipole Antenna VHA9103 2116 Schwarzbeck Oct-06 28 Dipole Antenna VHA9103 2117 Schwarzbeck Oct-06 29 Dipole Antenna UHA9105 2261 Schwarzbeck Oct-06 30 Dipole Antenna UHA9105 2262 Schwarzbeck Oct-06 31 Digital Multimeter 34401A US36062141 HP Apr-07 32 LISN KNW-407 8-1430-1 Kyoritsu Jan-07 33 Two-Line V-Network ESH3-Z5 893045/017 R&S Jan-07 34 Test Receiver ESHS10 828404009 R&S Jan-07 35 TEMP & HUMIDITY Chamber YJ-500 L05022 JinYoung Tech - Copyright ○ c 2006, LTA Co., Ltd. Page 28 of 28


Document Created: 2006-09-08 11:12:24
Document Modified: 2006-09-08 11:12:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC