Manual

FCC ID: S5751454941

Users Manual

Download: PDF
FCCID_3961118

SmartLine Wireless Pressure Transmitter ST 700 Gauge Pressure Models Specification 34-SW-03-xx, June 2018 Models: STGW740 0 to 500 psi 0 to 35,000 mbar STGW770 0 to 3,000 psi 0 to 210,000 mbar STGW73L 0 to 50 psi 0 to 3,500 mbar STGW74L 0 to 500 psi 0 to 35,000 mbar STGW77L 0 to 3,000 psi 0 to 210,000 mbar STGW78L 0 to 6,000 psi 0 to 420,000 mbar STGW79L 0 to 10,000 psi 0 to 690,000 mbar Introduction SmartLine Wireless Pressure continues the evolution of Honeywell’s wireless transmitter product offering and provides the latest critical advancements to support industrial automation users’ desire to expand wireless use for monitoring and control. With over 14 years of industrial wireless experience, Figure 1 — SmartLine Wireless Differential Pressure the SmartLine Wireless Pressure builds upon and is Transmitters compatible with the current XYR 6000 product porfotlio. Similar to the XYR 6000 wireless transmitter, the and operational in minutes, quickly providing information SmartLine Wireless product line is part of the back to your system. Honeywell OneWireless™ system and is ISA100 - The previous generation transmitters primarily were applied ready. to monitoring applicaions but experienced users know that Honeywell’s wireless products are as reliable, secure, and SmartLine Wireless Pressure transmitters also safe as their wired counterparts. With this knowledge, users leverage SmartLine technology in the incorporaton of are now looking for wireless transmiiters for use in specific the enhanced SmartLine Pressure meter body. By control applications. utilizing the same meter body as in the non-wireless pressure product offering, you get best-in-class SmartLine Wireless introduces a step change in performance, reduction in spares inventory, and a performance and most notably, performance suitable for lessening of the maintenance learning curve. control. SmartLine Wireless performance is improved in these ways: The SmartLine Wireless Pressure transmitter enables customers to obtain data and create information from  Fast ½ second publication rate remote and hazardous measurement locations without  Built-in additional noise reduction the need to run wires, where running wire is cost prohibitive and/or the measurement is in a hazardous  More powerful 4dBi integral antenna location. Without wires, transmitters can be installed  Good battery life performance even at ½ second publication rate.

SmartLine Wireless Pressure retains the following Span & Range Limits: desirable features from the XYR 6000 product offering:  Mesh or non-mesh configuration within each Model URL / Max LRL Min Span psi transmitter Span psi (bar) (bar)  Generic, off-the-shelf lithium ion battery. psi (bar) STGW740 500 (35) -14.7 (-1.0) 5 (.35)  Two “D” size batteries for longer life. STGW770 3000 (210) -14.7 (-1.0) 30 (2.1)  Choice of over-the-air or local provisioning Model psi (bar) psi (bar) psi (bar) (network security join key) STGW73L 50 (3.5) -14.7 (-1.0) 0.5 (.035)  Over-the-air firmware upgrade capability STGW74L 500 (35) -14.7 (-1.0) 5 (.35)  Unique, encrypted provisionng key delivered STGW77L 3000 (210) -14.7 (-1.0) 30 (2.1) from the factory STGW78L 6000 (420) -14.7 (-1.0) 60 (4.2)  Remote and integral antenna options STGW79L 10000 (690) -14.7 (-1.0) 100 )6.9)  24 VDC power option  Publication rates of 1, 5, 10, or 30 seconds, plus new selections for ½ sec, and 1, 15, 30, 60 minutes  Transmitter range (integral antenna) of 1150’ (350 m) under ideal conditions. The STGW700 dual head and inline gauge pressure series are suitable for monitoring, control and data acquisition. STGW700 dual head products feature piezoresistive sensor technology combining pressure sensing with on-chip temperature compensation capabilities providing high accuracy, stability and performance over a wide range of application pressures and temperatures Best in Class Features: o Accuracy up to 0.065 % of calibrated span o Stability up to 0.025% of URL per year for five years o Automatic temperature compensation o Rangeability up to 100:1 o Intuitive external zero & span capability o Integral dual seal design for safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0

Smart Line Wireless Features Mesh and non-mesh capability. All SmartLine Wireless Local and over-the-air provisioning capability. All transmitters can be configured to operate in either a mesh Honeywell wireless devices feature a secure method network or a star (non-mesh) network. The configuration to join the local wireless network, also known as is specific to each wireless transmitter and thus the provisioning. SmartLine Wireless transmitters feature network can consist of a mixture of meshing and non- two methods to provision a transmitter onto the meshing devices. Non-meshing is desirable for network which are either by using a handheld device deterministic communications which is preferred for to locally communicate through the IR interface or control. remotely using the over-the-air function. The over- Transmission power setting. To comply with local and the-air function is managed by the OneWireless regional requirements, SmartLine Wireless transmitters are gateway, Wireless Device Manager (WDM). set at the factory to the maximum transmission power In either method, the communication of secure, setting allowed for the country of use. unique provisioning keys is one of the main factors to Non-proprietary battery. Sourcing lithium thionyl chloride prevent against unintended access. Honeywell’s batteries is much simpler since SmartLine Wireless utilizes security keys are unique for each device from the commercial off-the-shelf batteries. Please see the list of factory, never made visible, always encrypted, and approved battery manufacturers later in this specification. uniquely generated from the gateway that manages Batteries are housed in an IS-approved battery the deployed network. compartment making battery changes safe and easy. Over-the-air firmware updates. Once joined as a Backward compatibility. SmartLine Wireless transmitters member of your OneWireless network, the WDM can can join existing OneWireless networks and interoperate download new transmitter firmware releases to each with existing XYR 6000 wireless transmitters or other SmartLine Wireless transmitter over the wireless ISA100 Wireless compliant transmitters or networks. network. Locating and accessing the transmitter locally is not required thus saving time and keeping your personnel in safe environments.

OneWireless Network Features The core of the Honeywell wireless solution is the OneWireless Network which consists a gateway, access point(s), and field routers. The Wireless Device Manager (WDM) serves as the gateway function and in this role, manages the communication from the wireless field devices to the process control application. Typically, the WDM connects logically to the process control network (Level 2 or wireless DMZ). As the wireless network manager, the WDM provides easy access to the entire wireless network through a browser-based user interface. The Honeywell WDM can manage devices communicating over the ISA100 Wireless protocol and the WirelessHART protocol. The ability to deploy redundant WDMs improves the reliability ensuring no loss of process data which is a requirement for control applications. The Field Device Access Point (FDAP) serves in two roles in the OneWireless network infrastructure, which are: 1) access point, and 2) field router. As an access point, the FDAP directly connects to the WDM via Ethernet LAN cable. More than one access point is permitted and, when more than one is present, it ensures dual path for communications into the WDM from the field devices. As a field router, the FDAP located in the field would communicate to the FDAP acting as an access point. Using the FDAP as a router is more efficient than using field devices as routers since FDAPs are line powered devices whereas field devices are typically battery powered, and the FDAP offers greater range. The meshing capability of FDAPs allows flexibility in the setup of the wireless network to fit the requirements for wireless network performance, in terms of reliable communications, performance, and future growth. The choice of non-meshing network may be desirable for decreased communication latency which a FDAP serving as a field router helps ensures. Wireless Specifications Parameter Description Wireless 2,400 to 2,483.5 MHz (2.4 GHz) Industrial, Scientific and Medical (ISM) band Communication DSSS - Direct Sequential Spread Spectrum per FCC 15.247 / IEEE 802.15.4 2006 Every data packet transmitted in either direction is verified (CRC check) and acknowledged by the receiving device. USA – FCC Certified Canada – IC Certified European Union – Radio Equipment Directive compliant DSSS RF Transmitter NA Selection –100 mW (20.0 dBm) maximum EIRP including antenna for USA and Canadian Power locations. EU Selection – 63 mW (18 dBm) maximum EIRP including antenna per RTTE/ETSI for EU locations. Compliant to ETSI EN 300 328 wireless standard Data PV Publish Cycle Time: Configurable as 0.5, 1, 5, 10, 30 seconds, plus 1, 15, 30, 60 minutes Rate: 250 Kbps Antennas Integral – 4 dBi omnidirectional monopole (default selection) Remote – 8 dBi omnidirectional monopole with up to 20 m cable and lightning surge arrester Remote – 14 dBi directional parabolic with up to 20 m cable and lightning surge arrester. Signal Range Nominal 350 m (1150 feet) between Field Transmitter and Infrastructure Unit (FDAP) when using 4 dBi Integral antenna with a clear line of sight* *Actual range will vary depending on antennas, cables and site topography.

Specifications Operating Conditions – All Models Parameter Reference Rated Condition Operative Limits Transportation Condition and Storage (at zero static) °C °F °C °F °C °F °C °F Ambient Temperature** 25 ±1 77 ±2 -40 to 85* -40 to 185* -40 to 85* -40 to 185* -55 to 120 -67 to 248 Ambient Temperature 25 ±1 77 ±2 -40 to 85°C -40 to 185°F LCD Display visible range Meter Body Temperature 25 ±1 77 ±2 -40 to 110 -40 to 230 -40 to 125 -40 to 257 -55 to 120 -67 to 248 Humidity %RH 10 to 55 0 to 100 0 to 100 0 to 100 Vacuum Region - Minimum Pressure All Models mmHg absolute Atmospheric 25 2 (short term1) in H2O absolute Atmospheric 13 1 (short term1) Maximum Allowable Working Standard: Pressure (MAWP) 2,3 STGW740: 500 psi (35 bar) STGW770: 3000 psi (210 bar) (ST700 products are rated to STGW73L: 50 psi (3.5 bar) Maximum Allowable Working STGW74L: 500 psi (35 bar) Pressure. MAWP depends on STGW78L: 6000 psi (420 bar) Approval Agency and transmitter STGW79L: 10000 psi (690 bar) materials of construction.) Vibration Maximum of 4g over 15 to 200Hz. Shock Maximum of 40g. Commercially available, non-proprietary 3.6V Lithium thionyl chloride (LiSOCl2) batteries, non-rechargeable, size D. Battery pack-only option is available. Approved list of the manufacturer models: 1. Xeno Energy XL-205F Power 2. Eagle Picher PT-2300H 3. Tadiran TL-5930/s 24 VDC power option.4 For Non I.S. application: 16 to 28 VDC Input range, max input current 100mA. For I.S. application: Barrier in accordance with the control drawing required, Entity parameters 30V, 120mA, 0.9W 1Short term equals 2 hours at 70°C (158°F) 2 Units can withstand overpressure of 1.5x MAWP without damage. 3 Consult factory for MAWP of SmartLine Wireless transmitters with CRN approval. 4 24V power option rated 80°C (176°F) ** The Ambient Limits shown are for Ordinary Non-Hazardous locations only. Refer to the appropriate Control Drawing, FM/CSA, ATEX, or IECEx for the Ambient Limits when installed in Hazardous Locations.

Remote Antenna Cables Remote Antennas 8 dBi Omnidirectional Antenna 14 dBi Directional Antenna

Performance Specifications Reference Accuracy (conformance to +/-3 Sigma) Table 1 Model URL LRL Min Span Maximum Stability Reference psi (bar) psi (bar) psi (bar) Turndown (% URL/ Yr Accuracy1,2 Ratio for ten years) (% Span) STGW740 500 (35) -14.7 (-1.0) 5 (0.35) 100:1 0.025 0.0650% STGW770 3000 (210) -14.7 (-1.0) 30 (2.1) 100:1 0.025 0.0650% STGW73L 50 (3.5) -14.7 (-1.0) 0.5 (0.035) 100:1 0.025 0.0650% STGW74L 500 (35) -14.7 (-1.0) 5 (0.35) 100:1 0.025 0.0650% STGW78L 6000 (420) -14.7 (-1.0) 60 (4.2) 100:1 0.025 0.0650% STGW79L 10000 (690) -14.7 (-1.0) 100 (6.9) 100:1 0.025 0.0650% Zero and span may be set anywhere within the listed (URL/LRL) range limits Accuracy at Specified Span, Temperature and Static Pressure Effects: (conformance to +/-3) Table to be provided Total Performance (% of Span): Total Performance Calculation: = +/- √ (Accuracy)2 + (Temperature Effect)2 Total Performance Examples (for comparison): @ 5:1 Turndown, +/-50oF (28oC) shift Table to be provided Typical Calibration Frequency: Calibration verification is recommended every two (2) years Notes: 1.Terminal Based Accuracy - Includes combined effects of linearity, hysteresis, and repeatability. Analog output adds 0 .006% of span. 2.For zero based spans and reference conditions of: 25 oC (77 oF) for LRV > = 0 psia, 10 to 55% RH, and 316 Stainless Steel barrier diaphragm.

Performance Under Rated Conditions – All Models Parameter Description Vibration Effect Less than +/- 0.1% of URL w/o damping Per IEC60770-1 field or pipeline, high vibration level (10-2000Hz: 0.21 displacement / 3g max acceleration) Electromagnetic Compatibility IEC 61326-3-1 Lightning Protection Option Leakage Current: 10uA max @ 42.4VDC 93C Impulse rating: 8/20uS 5000A (>10 strikes) 10000A (1 strike min.) 10/1000uS 200A (> 300 strikes) Lightning Surge Arrester Frequency range: 0 – 3 GHz, 50 Ohms, VSWR = 1:1.3 Max, Insertion Loss = 0.4 dB (Remote antenna only) Connectors Type N Female, Max, Gas Tube Element: 90 V ± 20%, Impulse Breakdown Voltage = 1,000 V ± 20%, Maximum Withstand Current = 5 KA. CE Conformity These transmitters are in conformity with the Radio Equipment Directive, ETSI EN 300 328 V2.1.1 including EMC standard EN61326-1 2013

Physical Specifications Parameter Description Mounting Bracket Carbon Steel (zinc-plated) or Stainless Steel angle bracket or flat bracket available. Electronic Housing Meets NEMA 4X (hosedown and corrosion resistant), IP 66/67 (hosedown and submersible to 1m). Epoxy-Polyester hybrid paint. Low Copper-Aluminum with 1/2” NPT or M20 Conduit Connections. Stainless Steel Housing (option) 316 SS Electronics Housing - with M20 Conduit Connections 316 SS Housing with 1/2" NPT Conduit Connection 316 SS or Grade CF8M, the casting equivalent of 316 SS with M20 or 1/2" NPT Conduit Connection. If ordered with the Remote Antenna options, the antenna parts are not SS or Marine type cables; the integral antenna uses SS parts. Process Connections 1/4-inch NPT; 1/2-inch NPT with adapter. Process heads meet DIN 19213 requirements. Mounting Can be mounted in virtually any position using the standard mounting bracket. Mounting should result in the antenna being vertically oriented. Bracket is designed to mount on 2- inch (50 mm) vertical or horizontal pipe. See Figure 2. Dimensions See Error! Reference source not found., Figure 4 and Figure 5 Net Weight Approximately 11 pounds (5 Kg) for STGW7X0, and 7 pounds (3.2 kg) for STGW7XL Materials Specifications (see model selection guide for availability/restrictions with various models) Parameter Description Barrier Diaphragms Material STG700 Dual Head: 316L SS, Hastelloy® C-2762 STG700 Inline: 316L SS, Hastelloy® C-2762 Process Head Material STG700 Dual Head: 316 SS3 STG700 Inline: 316L SS Vent/Drain Valves & Plugs 1 STG700 Dual Head:316 SS3 STG700 Inline: N/A Head Gaskets STG700 Dual Head: Glass-filled PTFE standard. STG700 Inline: N/A STG700 Dual Head: Carbon Steel (Zinc plated) standard. Options include 316 SS, Meter Body Bolting NACE A286 SS bolts and nuts. STG700 Inline: N/A Fill Fluid Silicone DC 200 oil, NEOBEE M-20, or CTFE (Chlorotrifluoroethylene) 1 ® Vent/Drains are sealed with Teflon 2 Hastelloy C-276 or UNS N10276 3 Supplied as 316 SS or as Grade CF8M, the casting equivalent of 316 SS.

Dual Head Gauge In-Line Gauge Figure 2 — Examples of typical mounting positions (antenna omitted)

millimeters Reference Dimensions: inches Dual Head Gauge

In-Line Gauge Figure 3 – Informational and dimensional drawing

Dual Head Gauge In-Line Gauge Figure 4 — Typical mounting dimensions for STDW740, STDW770, STDW7(3,4,7,8,9)L (rear view)

Dual Head Gauge

In-Line Gauge Figure 5 — Typical mounting dimensions for STDW740, STDW770, STDW7(3,4,7,8,9)L (rear view)

Hazardous Locations Approvals Refer to control drawing 50136123, in the User’s manual #34-SW-25-01, for intrinsically safe installation details AGENCY TYPE OF PROTECTION Ambient Temperature Intrinsically Safe: Class I; Division 1; Groups A, B, C, D; Class II, Division 1, Groups E, F, G; -40 o C to +85 o C Class III, Division 1; T4 Class I, Zone 0 Ex ia IIC T4 Class I, Zone 0 AEx ia IIC T4 Nonincendive: Class I; Division 2; Groups A, B, C, D; -40 o C to +85 o C : T5 Class II, Division 2, Groups E, F, G; -40 o C to +70 o C : T6 CSA Class III, Division 2, T6..T5 Class I, Zone 0/2 ec [ia] IIC, T6..T5 (USA and Class I, Zone 0/2 AEx ec [ia] IIC, T6..T5 Canada) Explosion-Proof/ Flameproof/Dust Proof: Class I, Division 1; Groups A, B, C, D; -40 o C to +85 o C : T5, T95C Class II, Division 1, Groups E, F, G; -40 o C to +70 o C : T6 Class III, Division 1; T6..T5 Class I, Zone 0/1 Ex d [ia] IIC T6..T5 Class I, Zone 0/1 AEx d [ia] IIC, T6..T5 DIP A21/II, III/1/EFG/Ex tb IIIC T95C Enclosure: Type 4X/ IP66/ IP67 AGENCY TYPE OF PROTECTION Ambient Temperature Intrinsically Safe: IS Class I, II, III; Division 1; Groups ABCDEFG; T4 -40 °C to +85 °C Class I, Zone 0 AEx ia IIC Ga T4 Class I, Zone 2[0] AEx ic [ia Ga] IIC Gc T4 Nonincendive: NI-AIS Class I; DIV 2; Groups ABCD; T5..T6 -40 °C to +85 °C : T5 FM Class I, Zone 2[0] AEx nA [ia Ga] IIC Gc, T5..T6 -40 °C to +70 °C : T6 ApprovalsTM (USA) Dust Proof: -40 °C to +85 °C : T5, T95°C DIP-AIS Class II, III DIV 1, Groups EFG; T5..T6 -40 °C to +70 °C : T6 Zone 21[20] AEx tb [ia Da] IIIC T95°C Db Enclosure: Type 4X/ IP66/ IP67

AGENCY TYPE OF PROTECTION Ambient Temperature Intrinsically Safe: -40 o C to +85 o C II 1 G Ex ia IIC T4 Ga II 3 G Ex ic IIC T4 Gc Flameproof / Dust Proof: -40 o C to +85 o C : T5, T95C ATEX II 2[1] G Ex d [ia] IIC T6..T5 Gb[Ga] -40 o C to +70 o C : T6 II 2[1] D Ex tb [ia] IIIC T95C Db[Da] Nonincendive: -40 o C to +85 o C : T5 II 3[1] G Ex ec [ia] IIC T6..T5 Gc[Ga] -40 o C to +70 o C : T6 Enclosure: IP66/ IP67 AGENCY TYPE OF PROTECTION Ambient Temperature Intrinsically Safe: -40 o C to +85 oC Ex ia IIC T4 Ga Ex ic IIC T4 Gc Flameproof / Dust Proof: -40 o C to +85 o C : T5, T95C Ex db [ia] IIC T6..T5 Gb[Ga] -40 o C to +70 o C : T6 IECEx Ex tb [ia] IIIC Db[Da] T95C Nonincendive: -40 o C to +85 o C : T5 Ex ec [ia] IIC T6..T5 -40 o C to +70 o C : T6 Enclosure: IP66/ IP67 Transmitter Options (indicated selection code is shown) ISA100 Wireless Release Selections (A or B) OneWireless R2xx represents the previous releases whereas R3xx is the current release. A OneWireless system with R3xx firmware can host R2xx and R3xx devices. Please select the option to match the targeted OneWireless system. Remote Antenna and Cables (M or D) The user can select one of the optional remote antennas listed. The selection of the antenna option automatically includes the remote antenna adapter. To complete the option selection, one of the remote antenna cables (1, 2, or 3) must also be selected. Lightning (Surge) Diverter and Cables (1, 2, or 3) The lightning surge diverter options includes the surge diverter and cable. The diverter features Type N connections (female) on both ends. The remote antenna adapter is not included. Remote Antenna Adapter (A) This option provides an adapter to be inserted into the opening where the integral antenna normally connects. The adapter is designed to connect to a remote antenna that the user supplies. It features a female Type N connection. Standard Diagnostics plus Anti-Alias Filter (3) This option enables the Anti-Alias filter option which attenuates the higher frequencies and helps to prevent aliasing components from being sampled.

Destination Country (CA, EU, or US) This selection sets the transmission power at the factory to comply with the installation country location. Custom Configuration (C) Customer specified configuration parameters are programmed into the transmitter at the factory. Configuration information needs to be communicated to Honeywell Order Management at time of order entry. Additionally, the Honeywell OneWireless user interface is accessible through any browser and thus all configurable parameters are visible and can be edited. Custom Calibration (B) Custom calibration would input customer specified LRV and URV values, and check linearity. LRV and URV information needs to be communicated to Honeywell Order Management at time of order entry. Mounting Brackets (1, 3, 5, or 7) The angle mounting bracket is available in either zinc-plated carbon steel or 316 stainless steel and is suitable for horizontal or vertical mounting on a two-inch (50 millimeter) pipe, as well as wall mounting. An additional flat mounting bracket is also available in carbon steel and 316 stainless steel for two-inch (50 millimeter) pipe mounting. Tagging (Option 1 or 2) The choice of 1 or 2 stainless steel wired-on tags is available. Each tag can accommodate additional data of up to 4 lines of 28 characters. The number of characters includes spaces. Note that the standard nameplate on the meter body contains the serial number and body-related data.

Sales and Service For application assistance, current specifications, ordering, pricing, and name of the nearest Authorized Distributor, contact one of the offices below. ASIA PACIFIC EMEA AMERICAS Honeywell Process Solutions, Honeywell Process Solutions, Honeywell Process Solutions, Phone: + 800 12026455 or Phone: + 800 12026455 or Phone: (TAC) (800) 423-9883 +44 (0) 1202645583 +44 (0) 1202645583 or (215) 641-3610 (TAC) hfs-tac- (Sales) 1-800-343-0228 support@honeywell.com Email: (Sales) Email: (Sales) Australia FP-Sales-Apps@Honeywell.com FP-Sales-Apps@Honeywell.com Honeywell Limited Phone: +(61) 7-3846 1255 or or FAX: +(61) 7-3840 6481 (TAC) (TAC) Toll Free 1300-36-39-36 hfs-tac-support@honeywell.com hfs-tac-support@honeywell.com Toll Free Fax: 1300-36-04-70 China – PRC - Shanghai Honeywell China Inc. Phone: (86-21) 5257-4568 Fax: (86-21) 6237-2826 Singapore Honeywell Pte Ltd. Phone: +(65) 6580 3278 Fax: +(65) 6445-3033 South Korea Honeywell Korea Co Ltd Phone: +(822) 799 6114 Fax: +(822) 792 9015 For more information To learn more about SmartLine Transmitters, visit www.honeywellprocess.com Or contact your Honeywell Account Manager Process Solutions Honeywell 1250 W Sam Houston Pkwy S Houston, USA, TX 77042 Honeywell Control Systems Ltd Honeywell House, Skimped Hill Lane Bracknell, England, RG12 1EB Shanghai City Centre, 100 Jungi Road Shanghai, China 20061 34-SW-03-01 June 2018 2018 Honeywell International Inc. www.honeywellprocess.com


Document Created: 2018-07-05 16:23:01
Document Modified: 2018-07-05 16:23:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC