User Manual Part 2

FCC ID: S29AIBAO

Users Manual

Download: PDF
FCCID_3256812

AIBAQ Quick Start Guide 11.0 Ready for flight Place the alrcraft In a wide open space, with the rear facing you. (This position is known as "TAIL IN") 11.1 Starting the aircraft (3) insert the battery. 2 Power on the remote controller and the aircraft. @ Put the alroraft in a horlzontal position, blue LED lights flashes slowly untl bright,indicating that IMU preheating is complete. @ Openthe Mobile Wi—Fi device, wait for 30 seconds, when at the same time appear"Albao—Ground—**"" and *Albac—Air—**"" , click *Albao—Ground—**"" , input password ©1234567890" to connect and exit settings after a successful connection. 11.2 Connect to APP Software Connect to operating software "Walkera Drone" — amea © Walkare Drone Click the icon Choose the sircraftAIBAO, Click"Connoct . EnterAPP the on mobile device lck" Go To Connect." main Interface. Connect to game software "Aibao GO" Armec0 Abes G0 x= «. Click the icon on moble device Conneciing..... Entor APP the main intertace. Atention: * Two APP cannot be used on the same mobile device at the same time, need to quit an APP to use another APP. a—

AIBAO Quick Start Guide 11.3 GPS indicator lights When the rear red LED light (GPS) begin to flash, you can work GPS function. 11.4 Motor Unlock / Lock Motor Unlock Push the switch to GPS mode or Manual mode or Mation mode, and the move theleft stick and right stick while outward and hold for more than 2 seconds. You will see the Front blue LED light flashes, indlicating that motors are unlocked. Motors will start rotating after unlocked. ‘ Aftention: * When it has GPS signal, you can unlock under the GPS mode (GPS) or Manual mode or Motion made. * Without the GPS signal, you can only unlock motors under Manual Mode. « After unlock the motor, if the flight does not start after 5 seconds, the motor will automatically enter the locked state. Motor Lock There are two methods to lock the motors. Method 1: When the alrcraft has landed, push and hold the throtle stick down. The motors will stop after 5 seconds. Method 2: Move the left and right stick while outward and hold for more than 2 seconds. You will see the front blue LED light always on, indicating that motors are locked. Method 1 Mathod 2



AIBAO Quick Start Guide RETURN TO HOME (Romoto controllor or APP oporation) & Lorg proesi y on (m cliciisiay n e aremotnceriter Ape Hietice en w the alonitnil t aiotlisim rium avtomateaty stematcaly Alrcraft with Home point horlzontal distance > 30m a. i the fight alide is highor than 25m, the airort Helghtonr HP>25n wl keop the currant alitude and retum above the Home Pointthan descand vertaly. “fi' b. Whon the fight attude is lower than 25m,tho ; lrcraft wil slovate automatically to 28m high 2im Hetntonr hP<2in ‘fi’ then fy back above the Home Point and fand Home raint vertcaly. Alroraft with Home point horizontal distance < 30m a. If the fightalitude is higher than 25m,the sirraft ‘fi will keop the current alitide and ratum above the i Home Point then descand verticaly. W 6. Ifthe fightalftude is lower than 26m, the alrratt wl keop the current alttude and retum above the "'M,,.,Hkm"fir Home Point then descend vertcaly. @tome uit Attontion: 1) Meke sure hattherecatvad GES agnal o red LED Ight bins) 2 To antara ky reum, lease don‘t move the tiar dsn and butns. 3) When ho akerstlost harenoto contrller lgnal, h wil autsmatlcaly oter Falsato RTHL 4) When he akcrutbatervotage is low then 7.OV,and akcrut wl Hermepaintherlzontal datance in grosterthan On, ant wl sctomatiolytm beck ithe anet wth the Home pobthorontalltance loss hen Am, snn wl decrsese octoratily fom th curent posttonanland. 5) GPsignalis not nomalor GPS dose net wek, can not achiev thenuto rii, butwl land actomatoaly. 42—

AIBAO Quick Start Guide Waypolnt Fllght (APP operation) Click the icon ((}) to enter the Waypoint Flght inteface. Waypoints Flight {APP operation} Click the Icon @ to entor the Weypolnts Flght Intorace. Video and photo (romoto controller or APP operation) *Remots Controller Operation *APP Operation 1) Choose working mode: photo or video Tou the Photo orvideo ean io take phote orvideo Te photn by 2 aaz proesig the butln of Remota Contrater friime e Comena setings "—— Video by prosang the utton Pheto or video kon of Remoto Contrler «) Working mode (Video or photo)

AIBAO Quick Start Guide 13.0 End Flying @ Manual landing, AUTO Landing or return to home function landing. @ First, Power off the aircraf, then tum off the Remote Controller. @® Finally, remove the battery from the alrerart. 14.0 Additional remarks 14.1 Compass Calibration ‘ Attention: + If there is circles or drif in flying, please callbrate the compass. (the motor must be locked and blue LED light always on) « Please callbration outdoors and far away from strong electromagnetic interference. The compass calibration steps are as follows: @ Do this by moving bath sticks DOWN and to the middle position at the same time about 5 seconds, the aircraft red LED light tum off, blue LED light flash slowiy. (@) Rotrte the aircraft 380 degreas in the horizontal direction untl the red LED light brighting, blue LED light flash slowiy. | @ Rotate the aircraft in the vertical direction (aircraft head down} 1 360 degrees untll both red LED and blue LED light are always bright, which Indicates that the calibration is successful, and then the aircraft is til in the horizontal position. If callbration is not successful, please re calibrate it according Grand 1 % the above mathode.

AIBAO Quick Start Guide 14.2 Remote Controller stick mode switch and stick calibration m * DEVO FBE stick modand stick oallbration has bean sat up before out of factory, if you need to awitch and calibration, please refor to the following methods. + It must be aperated under power off or motors are locked well Stick Mode Switch: Gnbal Onba Long press " Om"" buttom for 3—5 seconds, enter the stick mode change, short pross " @"m buttom, choose mode 1, mode 2, mode 3, mode 4 and then long pross **"”b" * buttorn for 1—2 seconds again, 0a9¢ comfiim and exit the change mode, "The Indloater reaet necording to the stick made mone 1 mobe 2 mones mone« MODE 2 | MODE 4 MODE2 and MODE4 Trrote Elovater Eovator are lefhand throttle Ruddlr+ Mllmn+ MODE 1 mObe 3 MODE1 and MODE3 Elovator Thratto Elevater Trrotie are right—hand throttle . Rudd-r<—1—> Allwon <-$-> Ailnmn4_1_> Ruddlr<_£.> X Cusfomization also supported in APP software. Stick Calibration: Shtairsim Long press * @ * button for 3 to 5 seconds,four lights fash altemataly to enter slck callbration. Operate the stick sevaral times within mechenical tuning range and then back in the middle. Long press the " G‘"‘%”“’“ * button for 3 to 5 seconde agaln, four Indlcatorlights turn on, then ex‘t sick callbration. Attention: * When you ext if vibrate alert, then the callbration fails, please recallbrate. 18.

NWF walkera & Tei: 400—9318—878 User manual is subject to change without prior notice. Pleass go to Walkera offclal website to get the latest version.

FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


Document Created: 2017-01-12 13:46:08
Document Modified: 2017-01-12 13:46:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC