Test Report 15C

FCC ID: RRK2005090049-1

Test Report

Download: PDF
FCCID_783793

FCC TEST REPORT (15.247) REPORT NO.: RF950518H03A MODEL NO.: WMP-D16 RECEIVED: March 16, 2007 TESTED: March 22, 2007 ISSUED: March 26, 2007 APPLICANT: Alpha Networks Inc. ADDRESS: No.8 Li-shing 7th Rd., Science-based Industrial Partk, Hsinchu, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation TEST LOCATION: No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. This test report consists of 28 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. No. 2177-01 Report No.: RF950518H03A 1 Report Format Version 2.0.5 Reference No.:960316H01

Table of Contents 1. CERTIFICATION.......................................................................................... 3 2. SUMMARY OF TEST RESULTS.................................................................. 4 3. GENERAL INFORMATION .......................................................................... 5 3.1 GENERAL DESCRIPTION OF EUT............................................................. 5 3.2 DESCRIPTION OF TEST MODES............................................................... 6 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL:............... 7 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................. 8 3.4 DESCRIPTION OF SUPPORT UNITS......................................................... 9 3.5 CONFIGURATION OF SYSTEM UNDER TEST .......................................... 9 4. TEST TYPES AND RESULTS (802.11a, 5725~5850MHz Band)................ 10 4.1 RADIATED EMISSION MEASUREMENT .................................................. 10 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT ................................ 10 4.1.2 TEST INSTRUMENTS ............................................................................... 11 4.1.3 TEST PROCEDURES................................................................................ 12 4.1.4 DEVIATION FROM TEST STANDARD ...................................................... 12 4.1.5 TEST SETUP............................................................................................. 13 4.1.6 EUT OPERATING CONDITIONS............................................................... 13 4.1.7 TEST RESULTS ........................................................................................ 14 4.2 MAXIMUM PEAK OUTPUT POWER ......................................................... 18 4.2.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT........... 18 4.2.2 INSTRUMENTS......................................................................................... 18 4.2.3 TEST PROCEDURES................................................................................ 19 4.2.4 DEVIATION FROM TEST STANDARD ...................................................... 19 4.2.5 TEST SETUP............................................................................................. 19 4.2.6 EUT OPERATING CONDITIONS............................................................... 19 4.2.7 TEST RESULTS ........................................................................................ 20 4.3 BAND EDGES MEASUREMENT ............................................................... 21 4.3.1 LIMITS OF BAND EDGES MEASUREMENT............................................. 21 4.3.2 TEST INSTRUMENTS ............................................................................... 21 4.3.3 TEST PROCEDURE .................................................................................. 22 4.3.4 DEVIATION FROM TEST STANDARD ...................................................... 22 4.3.5 EUT OPERATING CONDITION ................................................................. 22 4.3.6 TEST RESULTS ........................................................................................ 23 4.4 ANTENNA REQUIREMENT....................................................................... 26 4.4.1 STANDARD APPLICABLE ......................................................................... 26 4.4.2 ANTENNA CONNECTED CONSTRUCTION ............................................. 26 5. INFORMATION ON THE TESTING LABORATORIES ............................... 27 APPENDIX-A ............................................................................................... A-1 Report No.: RF950518H03A 2 Report Format Version 2.0.5 Reference No.:960316H01

1. CERTIFICATION PRODUCT: IEEE802.11a/b/g mini PCI card BRAND NAME: Alpha MODEL NO.: WMP-D16 TEST SAMPLE: ENGINEERING SAMPLE TESTED: March 22, 2007 APPLICANT: Alpha Networks Inc. STANDARDS: FCC Part 15, Subpart C (Section 15.247), ANSI C63.4-2003 The above equipment (Model: WMP-D16) has been tested by Advance Data Technology Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: March 26, 2007 ( Midoli Peng ) TECHNICAL ACCEPTANCE : , DATE: March 26, 2007 Responsible for RF ( Moris Lin ) APPROVED BY : , DATE: March 26, 2007 (Hank Chung, Deputy Manager ) Report No.: RF950518H03A 3 Report Format Version 2.0.5 Reference No.:960316H01

2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: For 802.11a, 5725~5850MHz Band APPLIED STANDARD: FCC Part 15, Subpart C (Section 15.247) Standard Test Type and Limit Result Remark Section Maximum Peak Output Power Meet the requirement 15.247(b) PASS Limit: max. 30dBm of limit. Meet the requirement of limit. Radiated Emissions 15.247(d) PASS Minimum passing Limit: Table 15.209 margin is –6.24dB at 217.38MHz Band Edge Measurement Meet the requirement 15.247(d) Limit: 20dB less than the peak PASS of limit. value of fundamental frequency NOTE: 1. The EUT was operating in 5.150 ~ 5.250GHz and 5.725 ~ 5.850GHz frequencies band. This report was recorded the RF parameters including 5.725 ~ 5.850GHz. For the 5.150 ~ 5.250GHz RF parameters was recorded in another test report. 2. This report is prepared for FCC class II permissive change. Only radiated emission, Maximum Peak Output Power and Band Edge Measurement were presented in this test report. Report No.: RF950518H03A 4 Report Format Version 2.0.5 Reference No.:960316H01

3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT IEEE802.11a/b/g mini PCI card MODEL NO. WMP-D16 FCC ID RRK2005090049-1 POWER SUPPLY DC 3.3V from host equipment MODULATION 64QAM, 16QAM, QPSK, BPSK for OFDM TYPE MODULATION OFDM TECHNOLOGY TRANSFER RATE 802.11a: 54/48/36/24/18/12/9/6Mbps FREQUENCY 802.11a: 5.15 ~ 5.25GHz and 5.725 ~ 5.850GHz RANGE NUMBER OF 802.11a: 9 CHANNEL CHANNEL 802.11a: 20MHz for Normal mode SPACING For FCC15.247: 87.096mW OUTPUT POWER For FCC15.407: 45.604mW ANTENNA TYPE Please see note 1 NOTE: 1. This report is prepared for FCC class II permissive change. The difference compared with the Report No.:RF950518H03 design is as the following: u Cancel Original model of WMP-D18 (with Turbo feature). u Cancel Original frequency: 5250MHz-5350MHz. Report No.: RF950518H03A 5 Report Format Version 2.0.5 Reference No.:960316H01

u Add one antenna for 5GHz. (Only apply 5150MHz-5250MHz & 5725MHz-5850MHz band) Original Report (Report No.:RF950518H03) For 2.4GHz No. Model No. Gain (dBi) Antenna Type Connector 1 WSS001 2 Dipole RP-SMA(M) 2 WPB002-3 4.5 PCB MHF Note: Antenna 1 is connected with Main port of EUT Antenna 2 is connected with AUX port of EUT For 5GHz Cable Loss Net Gain No. Model No. Gain (dBi) Antenna Type Connector (dB) (dB) 1 SAA04-220080 5 1.8 3.2 Dipole RP-N plug Note: Antenna 1 is connected with Main port of EUT Add one new antenna < Only apply 5150MHz-5250MHz & 5725MHz-5850MHz band > Cable Loss Net Gain Antenna Model No. Gain (dBi) Connector RF cable (dB) (dB) Type 3 0.785 2.215 100 mm 3 0.785 2.215 100 mm MAF94192 PIFA I-PEX MHF 3 1.1 1.9 120 mm 3 1.5 1.5 160 mm Note: 1. There will have four conditions for this antenna. 2. The bold type was chose for test. 2. The above EUT information was declared by the manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. 3.2 DESCRIPTION OF TEST MODES Operated in 5725 ~ 5850MHz band: Five channels are provided to this EUT. Channel Frequency 1 5745 MHz 2 5765 MHz 3 5785 MHz 4 5805 MHz 5 5825 MHz Report No.: RF950518H03A 6 Report Format Version 2.0.5 Reference No.:960316H01

3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: EUT Applicable to configure Description mode PLC RE<1G RE≥1G APCM - X √ √ √ NA Where PLC: Power Line Conducted Emission RE<1G RE: Radiated Emission below 1GHz RE≥1G: Radiated Emission above 1GHz APCM: Antenna Port Conducted Measurement Radiated Emission Test (Below 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Available Tested Modulation Modulation Data Rate Mode Channel Channel Technology Type (Mbps) 802.11a 1 to 5 5 OFDM BPSK 6 Radiated Emission Test (Above 1 GHz):  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Data Available Tested Modulation Modulation Mode Rate Channel Channel Technology Type (Mbps) 802.11a 1 to 5 1, 3, 5 OFDM BPSK 6 Bandedge Measurement:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Data Available Tested Modulation Modulation Mode Rate Channel Channel Technology Type (Mbps) 802.11a 1 to 5 1, 5 OFDM BPSK 6 Antenna Port Conducted Measurement:  Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Data Available Tested Modulation Modulation Mode Rate Channel Channel Technology Type (Mbps) 802.11a 1 to 5 1, 3, 5 OFDM BPSK 6 Report No.: RF950518H03A 7 Report Format Version 2.0.5 Reference No.:960316H01

3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is an IEEE802.11a/b/g mini PCI card. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C. (15.247) ANSI C63.4-2003 All test items have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF950518H03A 8 Report Format Version 2.0.5 Reference No.:960316H01

3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. No. Product Brand Model No. Serial No. FCC ID NOTEBOOK WFY93-WQ98K-BH 1 HP HSTNN-S19C DoC COMPUTER 87F-KD366-RB773 2 Extend Card ADT NA NA NA No. Signal cable description 1 NA 2 NA Note: 1. All power cords of the above support units are unshielded (1.8m). 3.5 CONFIGURATION OF SYSTEM UNDER TEST EUT 1. NOTEBOOK COMPUTER Extend Card TEST TABLE NOTE: 1. Please refer to the photos of test configuration. Report No.: RF950518H03A 9 Report Format Version 2.0.5 Reference No.:960316H01

4. TEST TYPES AND RESULTS (802.11a, 5725~5850MHz Band) 4.1 RADIATED EMISSION MEASUREMENT 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following: Frequencies Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF950518H03A 10 Report Format Version 2.0.5 Reference No.:960316H01

4.1.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER UNTIL ADVANTEST Spectrum Analyzer R3271A 85060311 July 03, 2007 HP Pre_Amplifier 8449B 3008A01922 Sep. 18, 2007 ROHDE & SCHWARZ ESCS30 100375 Sep. 20, 2007 Test Receiver CHASE Broadband Antenna VULB 9168 138 July 17, 2007 Schwarzbeck Horn_Antenna BBHA9120 D124 Jan. 01, 2008 Schwarzbeck Horn_Antenna BBHA 9170 BBHA9170153 Jan. 05, 2008 SCHWARZBECK VHBA9123 459 Jun. 08, 2009 Biconical Antenna SCHWARZBECK UPA6108 1148 Jun. 08, 2009 Periodic Antenna RF Switches (ARNITSU) CS-201 1565157 NA RF CABLE (Chaintek) SF102 22054-2 Nov. 14. 2007 9913-30M N-N STCCAB-30M-1 RF Cable(RICHTEC) Jul. 15, 2007 Cable GHz ADT_Radiated_V Software NA NA 5.14 CHANCE MOST AT-100 0203 NA Antenna Tower CHANCE MOST Turn Table TT-100 0203 NA Note: 1. The calibration interval of the above test instruments is 12 months (36 months for Biconical and Periodic Antenna)and the calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna, HP preamplifier (model: 8449B) and Spectrum Analyzer (model: R3271A) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in ADT Open Site No. C. 4. The FCC Site Registration No. is 656396. 5. The VCCI Site Registration No. is R-1626. 6. The CANADA Site Registration No. is IC 4824A-3. 7. The following table is for the measurement uncertainty, which is calculated as per the document CISPR 16-4. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Measurement Value Radiated emissions (30MHz-1GHz) 3.89 dB Radiated emissions (1GHz ~18GHz) 2.21 dB Radiated emissions (18GHz ~40GHz) 1.88 dB Report No.: RF950518H03A 11 Report Format Version 2.0.5 Reference No.:960316H01

4.1.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth is 1MHz and video bandwidth of test receiver/spectrum analyzer is 3MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 10 Hz for Average detection (AV) at frequency above 1GHz. 4.1.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF950518H03A 12 Report Format Version 2.0.5 Reference No.:960316H01

4.1.5 TEST SETUP For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 4.1.6 EUT OPERATING CONDITIONS a. Connect the EUT with the support unit 1 (Notebook computer) which placed on a testing table. b. The support unit 1 (Notebook computer) ran a test program “Art 52 Build 13” to enable EUT under transmission condition continuously. Report No.: RF950518H03A 13 Report Format Version 2.0.5 Reference No.:960316H01

4.1.7 TEST RESULTS Below 1GHz Worst-Case Data MODULATION FREQUENCY BPSK Below 1000MHz TYPE RANGE INPUT POWER 120Vac, 60 Hz TRANSFER RATE 6Mbps (SYSTEM) ENVIRONMENTAL 22deg. C, 60%RH, DETECTOR CONDITIONS 955hPa FUNCTION Quasi-Peak TESTED BY Eric Lee ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 129.52 37.73 QP 43.50 -5.77 1.45 H 20 25.36 12.37 2 193.38 34.96 QP 43.50 -8.54 1.53 H 170 24.07 10.89 3 199.79 33.12 QP 43.50 -10.38 1.25 H 31 21.97 11.15 4 209.88 34.40 QP 43.50 -9.10 1.84 H 231 22.72 11.68 5 217.38 39.76 QP 46.00 -6.24 1.16 H 148 27.69 12.07 6 268.99 30.91 QP 46.00 -15.09 1.26 H 149 15.70 15.21 7 301.00 34.88 QP 46.00 -11.12 1.09 H 344 18.88 16.00 8 368.88 34.48 QP 46.00 -11.52 1.49 H 268 16.92 17.56 9 399.99 29.31 QP 46.00 -16.69 1.58 H 184 10.61 18.70 10 426.88 34.47 QP 46.00 -11.53 1.24 H 0 15.56 18.91 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 114.62 36.81 QP 43.50 -6.69 1.29 V 240 24.73 12.08 2 118.92 34.14 QP 43.50 -9.36 1.52 V 95 21.93 12.21 3 133.49 37.01 QP 43.50 -6.49 1.00 V 4 24.58 12.43 4 199.74 32.19 QP 43.50 -11.31 1.67 V 20 21.05 11.14 5 229.00 34.93 QP 46.00 -11.07 1.36 V 233 22.24 12.69 6 231.38 39.18 QP 46.00 -6.82 1.36 V 178 26.37 12.81 7 267.01 31.19 QP 46.00 -14.81 1.31 V 145 16.06 15.13 8 280.00 35.25 QP 46.00 -10.75 1.37 V 89 19.76 15.49 9 339.30 37.71 QP 46.00 -8.29 1.29 V 253 21.04 16.67 10 420.80 35.48 QP 46.00 -10.52 1.08 V 20 16.61 18.87 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: RF950518H03A 14 Report Format Version 2.0.5 Reference No.:960316H01

802.11a OFDM modulation FREQUENCY CHANNEL Channel 1 1 ~ 40 GHz RANGE MODULATION BPSK TRANSFER RATE 6Mbps TYPE INPUT POWER DETECTOR Peak(PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 22deg. C, 60%RH, TESTED BY Eric Lee CONDITIONS 955hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 #3830.00 46.90 PK 74.00 -27.10 1.43 H 82 12.96 33.94 2 #3830.00 41.90 AV 54.00 -12.10 1.43 H 82 7.96 33.94 3 *5745.00 101.91 PK 1.48 H 242 63.65 38.26 4 *5745.00 92.91 AV 1.48 H 242 54.65 38.26 5 #11490.00 41.25 PK 74.00 -32.75 1.68 H 326 -5.71 46.96 6 #11490.00 30.14 AV 54.00 -23.86 1.68 H 326 -16.82 46.96 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 #3830.00 49.32 PK 74.00 -24.68 1.47 V 245 15.38 33.94 2 #3830.00 42.56 AV 54.00 -11.44 1.47 V 245 8.62 33.94 3 *5745.00 103.56 PK 1.11 V 110 65.30 38.26 4 *5745.00 96.56 AV 1.11 V 110 58.30 38.26 5 #11490.00 43.35 PK 74.00 -30.65 1.02 V 323 -3.61 46.96 6 #11490.00 33.00 AV 54.00 -21.00 1.02 V 323 -13.96 46.96 NOTE: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value 5. “*” : Fundamental frequency 6. “#”The radiated frequency falling in the restricted band. 7. The limit value is defined as per 15.247 Report No.: RF950518H03A 15 Report Format Version 2.0.5 Reference No.:960316H01

FREQUENCY CHANNEL Channel 3 1 ~ 40 GHz RANGE MODULATION BPSK TRANSFER RATE 6Mbps TYPE INPUT POWER DETECTOR Peak(PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 22deg. C, 60%RH, TESTED BY Eric Lee CONDITIONS 955hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 #3856.60 46.58 PK 74.00 -27.42 1.47 H 56 12.55 34.03 2 #3856.60 42.25 AV 54.00 -11.75 1.47 H 56 8.22 34.03 3 *5785.00 101.50 PK 1.51 H 250 63.21 38.30 4 *5785.00 92.53 AV 1.51 H 250 54.24 38.30 5 #11570.00 40.25 PK 74.00 -33.75 1.68 H 9 -6.67 46.92 6 #11570.00 30.65 AV 54.00 -23.35 1.68 H 9 -16.27 46.92 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 #3856.60 49.99 PK 74.00 -24.01 1.20 V 24 18.27 31.72 2 #3856.60 43.23 AV 54.00 -10.77 1.20 V 24 11.51 31.72 3 *5785.00 103.16 PK 1.12 V 130 64.86 38.30 4 *5785.00 95.94 AV 1.12 V 130 57.64 38.30 5 #11570.00 44.23 PK 74.00 -29.77 1.36 V 325 -2.70 46.92 6 #11570.00 33.65 AV 54.00 -20.35 1.36 V 325 -13.27 46.92 NOTE: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value 5. “*” : Fundamental frequency 6. “#”The radiated frequency falling in the restricted band. 7. The limit value is defined as per 15.247 Report No.: RF950518H03A 16 Report Format Version 2.0.5 Reference No.:960316H01

FREQUENCY CHANNEL Channel 5 1 ~ 40 GHz RANGE MODULATION BPSK TRANSFER RATE 6Mbps TYPE INPUT POWER DETECTOR Peak(PK) 120Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 22deg. C, 60%RH, TESTED BY Eric Lee CONDITIONS 955hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 #3883.30 47.42 PK 74.00 -26.58 1.14 H 52 13.30 34.12 2 #3883.30 42.65 AV 54.00 -11.35 1.14 H 52 8.53 34.12 3 *5825.00 101.22 PK 1.50 H 260 62.87 38.35 4 *5825.00 92.22 AV 1.50 H 260 53.87 38.35 5 #11650.00 40.24 PK 74.00 -33.76 1.58 H 224 -6.62 46.86 6 #11650.00 30.35 AV 54.00 -23.65 1.58 H 224 -16.51 46.86 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 #3883.30 50.24 PK 74.00 -23.76 1.69 V 163 16.12 34.12 2 #3883.30 43.23 AV 54.00 -10.77 1.69 V 163 9.11 34.12 3 *5825.00 102.59 PK 1.11 V 110 64.24 38.35 4 *5825.00 95.34 AV 1.11 V 110 56.99 38.35 5 #11650.00 43.36 PK 74.00 -30.64 1.54 V 24 -3.50 46.86 6 #11650.00 33.68 AV 54.00 -20.32 1.54 V 24 -13.18 46.86 NOTE: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value 5. “*” : Fundamental frequency 6. “#”The radiated frequency falling in the restricted band. 7. The limit value is defined as per 15.247 Report No.: RF950518H03A 17 Report Format Version 2.0.5 Reference No.:960316H01

4.2 MAXIMUM PEAK OUTPUT POWER 4.2.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT The Maximum Peak Output Power Measurement is 30dBm. 4.2.2 INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until R&S SPECTRUM ANALYZER FSP40 100037 Aug. 15, 2007 Agilent SIGNAL GENERATOR E8257C MY43321031 July 26, 2007 TEKTRONIX OSCILLOSCOPE TDS380 B016335 Jun. 21, 2007 NARDA DETECTOR 4503A FSCM99899 NA NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF950518H03A 18 Report Format Version 2.0.5 Reference No.:960316H01

4.2.3 TEST PROCEDURES 1. A detector was used on the output port of the EUT. An oscilloscope was used to read the response of the detector. 2. Replaced the EUT by the signal generator. The center frequency of the S.G was adjusted to the center frequency of the measured channel. 3. Adjusted the power to have the same reading on oscilloscope. Record the power level. 4.2.4 DEVIATION FROM TEST STANDARD No deviation 4.2.5 TEST SETUP DETECTOROR OSCILLOSCOPE EUT or S.G 4.2.6 EUT OPERATING CONDITIONS Same as Item 4.1.6 Report No.: RF950518H03A 19 Report Format Version 2.0.5 Reference No.:960316H01

4.2.7 TEST RESULTS 802.11a OFDM modulation MODULATION BPSK TRANSFER RATE 6Mbps TYPE INPUT POWER ENVIRONMENTAL 27deg. C, 53%RH, 120Vac, 60 Hz (SYSTEM) CONDITIONS 955hPa TESTED BY Eric Lee ) Antenna (Gain : 3 dBi) + Antenna Cable (0.785dB loss) CHANNEL PEAK POWER PEAK POWER PEAK POWER CHANNEL FREQUENCY OUTPUT OUTPUT LIMIT PASS/FAIL (MHz) (mW) (dBm) (dBm) 1 5745 85.114 19.3 30 PASS 3 5785 85.114 19.3 30 PASS 5 5825 87.096 19.4 30 PASS Report No.: RF950518H03A 20 Report Format Version 2.0.5 Reference No.:960316H01

4.3 BAND EDGES MEASUREMENT 4.3.1 LIMITS OF BAND EDGES MEASUREMENT Below –20dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth). 4.3.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until R&S SPECTRUM ANALYZER FSP40 100037 Aug. 15, 2007 NOTE: 1.The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. 2.The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF950518H03A 21 Report Format Version 2.0.5 Reference No.:960316H01

4.3.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 MHz bandwidth from band edge. The band edges was measured and recorded. 4.3.4 DEVIATION FROM TEST STANDARD No deviation 4.3.5 EUT OPERATING CONDITION Same as Item 4.1.6 Report No.: RF950518H03A 22 Report Format Version 2.0.5 Reference No.:960316H01

4.3.6 TEST RESULTS The spectrum plots are attached on the following pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(d). Report No.: RF950518H03A 23 Report Format Version 2.0.5 Reference No.:960316H01

802.11a OFDM modulation Report No.: RF950518H03A 24 Report Format Version 2.0.5 Reference No.:960316H01

CH 1 CH 5 Report No.: RF950518H03A 25 Report Format Version 2.0.5 Reference No.:960316H01

4.4 ANTENNA REQUIREMENT 4.4.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247(a), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 4.4.2 ANTENNA CONNECTED CONSTRUCTION The antenna used in this product is as following: Cable Loss Net Gain Antenna Model No. Gain (dBi) Connector (dB) (dB) Type MAF94192 3 0.785 2.215 PIFA I-PEX MHF Report No.: RF950518H03A 26 Report Format Version 2.0.5 Reference No.:960316H01

5. INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025. USA FCC, UL, A2LA Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA , CSA R.O.C. CNLA, BSMI, NCC Netherlands Telefication Singapore PSB , GOST-ASIA(MOU) Russia CERTIS(MOU) Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26052943 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050 Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also Report No.: RF950518H03A 27 Report Format Version 2.0.5 Reference No.:960316H01

APPENDIX-A MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications are made to the EUT by the lab during the test. Report No.: RF950518H03A A-1 Report Format Version 2.0.5 Reference No.:960316H01


Document Created: 2007-04-23 16:09:05
Document Modified: 2007-04-23 16:09:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC