Test Report DTS BT

FCC ID: RQQHLT-FS40401

Test Report

Download: PDF
FCCID_4077777

Model: M L465 FCC C Partt 15C M Measur remen nt and d Test Repoort For Hyund dai Corpo oration 25,, Yulgok-rro 2-Gil, JJongno-gu u, Seoul, South S Koorea FC CC ID: R RQQHL LT-FS404 401 FCC Rulle(s): FCC Part 15.247 7 Productt Descriptio on: 4G Sm mart Phone e Tested M Model: L465 Report N No.: STR1 18108061I-5 5 Sample Receipt Da ate: 2018--10-11 Tested D Date: 2018--10-12 to 20 018-11-02 Issued D Date: 2018--11-02 Tested B By: Jason n Su / Engin neer ed By: Reviewe Silin C Chen / EMC C Manager ed & Autho Approve orized By: Jandyy So / PSQ Manager Prepared By: Shenzhe en SEM Te est Technollogy Co., Ltd. L 1/F, Building A, Hong gwei Industrrial Park, Liuxian 2nd R Road, Bao'an District, Shen nzhen, P.R..C.（518101） Tel.: +86-75 55-33663308 8 Fax.: +86 6-755-336633 309 Websitte: www.sem mtest.com.cn Note: T This test repport is limite ed to the abbove client company c an nd the produuct model only. o It may noot be dupliccated withou ut prior perm mitted by Shhenzhen SE EM Test Tecchnology Co., C Ltd. Report No.: S STR181080611I-5 Page 1 of 34 4 FCC Part P 15.247

Model: L465 TABLE OF CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ...............................................................................3 1.2 TEST STANDARDS...................................................................................................................................................4 1.3 TEST METHODOLOGY .............................................................................................................................................4 1.4 TEST FACILITY .......................................................................................................................................................4 1.5 EUT SETUP AND TEST MODE .................................................................................................................................5 1.6 MEASUREMENT UNCERTAINTY ..............................................................................................................................5 1.7 TEST EQUIPMENT LIST AND DETAILS .....................................................................................................................6 2. SUMMARY OF TEST RESULTS ...........................................................................................................................7 3. RF EXPOSURE .........................................................................................................................................................8 3.1 STANDARD APPLICABLE.........................................................................................................................................8 3.2 TEST RESULT..........................................................................................................................................................8 4. ANTENNA REQUIREMENT ..................................................................................................................................9 4.1 STANDARD APPLICABLE.........................................................................................................................................9 4.2 EVALUATION INFORMATION ..................................................................................................................................9 5. POWER SPECTRAL DENSITY ...........................................................................................................................10 5.1 STANDARD APPLICABLE.......................................................................................................................................10 5.2 TEST PROCEDURE .................................................................................................................................................10 5.3 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................10 6. DTS BANDWIDTH .................................................................................................................................................12 6.1 STANDARD APPLICABLE.......................................................................................................................................12 6.2 TEST PROCEDURE .................................................................................................................................................12 6.3 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................12 7. RF OUTPUT POWER ............................................................................................................................................14 7.1 STANDARD APPLICABLE.......................................................................................................................................14 7.2 TEST PROCEDURE .................................................................................................................................................14 7.3 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................14 8. FIELD STRENGTH OF SPURIOUS EMISSIONS .............................................................................................16 8.1 STANDARD APPLICABLE.......................................................................................................................................16 8.2 TEST PROCEDURE .................................................................................................................................................16 8.3 CORRECTED AMPLITUDE & MARGIN CALCULATION ............................................................................................17 8.4 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................17 9. OUT OF BAND EMISSIONS .................................................................................................................................25 9.1 STANDARD APPLICABLE.......................................................................................................................................25 9.2 TEST PROCEDURE .................................................................................................................................................25 9.3 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................26 10. CONDUCTED EMISSIONS ................................................................................................................................32 10.1 TEST PROCEDURE ...............................................................................................................................................32 10.2 BASIC TEST SETUP BLOCK DIAGRAM .................................................................................................................32 10.3 TEST RECEIVER SETUP .......................................................................................................................................32 10.4 SUMMARY OF TEST RESULTS/PLOTS ..................................................................................................................32 Report No.: STR18108061I-5 Page 2 of 34 FCC Part 15.247

Model: L465 1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Client Information Applicant: Hyundai Corporation Address of applicant: 25, Yulgok-ro 2-Gil, Jongno-gu, Seoul, South Korea Manufacturer: Guizhou Fortuneship Technology Co., Ltd Address of manufacturer: 2nd Floor, Factory Building 4, Hi-Tech Industrial Park, Xinpu Economic Development Zone, Xinpu New District, Zunyi City, Guizhou Province, P. R. China General Description of EUT Product Name: 4G Smart Phone Brand Name: HYUNDAI Model No.: L465 Adding Model(s): L465S Rated Voltage: DC3.7V Battery: 1400mAh HY-C700 Power Adapter: Input:AC100-240V 50/60Hz Output::DC5V 700mA FS272_CF13_DRV_ONLY_MS410_O24574M_ Software Version: 20180920_WVGA_VOLTE__W1245_L234728B_CTP_ UDC_debug_165948 Hardware Version: FS272-M Note: The test data is gathered from a production sample, provided by the manufacturer. The main-test model L465 has two SIM card slots, adding model L465S has only one SIM card slots, but the circuit and the electronic construction do not change, declared by the manufacturer. The two models are test and only the worst case model is showed in the test report. Technical Characteristics of EUT Bluetooth Version: V4.2 (BLE mode) Frequency Range: 2402-2480MHz RF Output Power: -0.614dBm (Conducted) Data Rate: 1Mbps Modulation: GFSK Quantity of Channels: 40 Channel Separation: 2MHz Type of Antenna: Integral Antenna Report No.: STR18108061I-5 Page 3 of 34 FCC Part 15.247

Model: L465 Antenna Gain: 1.4dBi Lowest Internal Frequency of EUT: 32.768KHz 1.2 Test Standards The tests were performed according to following standards: FCC Rules Part 15.247: Frequency Hopping, Direct Spread Spectrum and Hybrid Systems that are in operation within the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz. 558074 D01 15.247 Meas Guidance v05: Guidance For Compliance Measurements On Digital Transmission System, Frequency Hopping Spread Spectrum System, And Hybrid System Devices Operating Under Section 15.247 Of The Fcc Rules ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices. Maintenance of compliance is the responsibility of the manufacturer. Any modification of the product, which result in lowering the emission, should be checked to ensure compliance has been maintained. 1.3 Test Methodology All measurements contained in this report were conducted with ANSI C63.10-2013, KDB 558074 D01 15.247 Meas Guidance v05 The equipment under test (EUT) was configured to measure its highest possible emission level. The test modes were adapted accordingly in reference to the Operating Instructions. 1.4 Test Facility FCC – Registration No.: 125990 Shenzhen SEM Test Technology Co., Ltd. Laboratory has been recognized to perform compliance testing on equipment subject to the Commissions Declaration Of Conformity (DOC). The Designation Number is CN5010, and Test Firm Registration Number is 125990. Industry Canada (IC) Registration No.: 11464A The 3m Semi-anechoic chamber of Shenzhen SEM.Test Technology Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 11464A. Report No.: STR18108061I-5 Page 4 of 34 FCC Part 15.247

Model: L465 1.5 EUT Setup and Test Mode The EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements. All testing shall be performed under maximum output power condition, with a duty cycle equal to 100%, and to measure its highest possible emissions level, more detailed description as follows: Test Mode List Test Mode Description Remark TM1 Low 2402MHz TM2 Middle 2440MHz TM3 High 2480MHz Test Conditions Temperature: 22~25 C Relative humidity 50~55 %. ATM Pressure: 1019 mbar EUT Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite USB Cable 1.2 Unshielded Without Ferrite Earphone Cable 1.2 Unshielded Without Ferrite Special Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite / / / / Auxiliary Equipment List and Details Description Manufacturer Model Serial Number / / / / 1.6 Measurement Uncertainty Measurement uncertainty Parameter Conditions Uncertainty RF Output Power Conducted ±0.42dB Occupied Bandwidth Conducted ±1.5% Power Spectral Density Conducted ±1.8dB Conducted Spurious Emission Conducted ±2.17dB 9-150kHz ±3.74dB Conducted Emissions Conducted 0.15-30MHz ±3.34dB 30-200MHz ±4.52dB 0.2-1GHz ±5.56dB Transmitter Spurious Emissions Radiated 1-6GHz ±3.84dB 6-18GHz ±3.92dB Report No.: STR18108061I-5 Page 5 of 34 FCC Part 15.247

Model: L465 1.7 Test Equipment List and Details No. Description Manufacturer Model Serial No. Cal Date Due Date Spectrum SEMT-1072 Agilent E4407B MY41440400 2018-05-22 2019-05-21 Analyzer Spectrum Rohde & SEMT-1031 FSP30 836079/035 2018-05-22 2019-05-21 Analyzer Schwarz EMI Test Rohde & SEMT-1007 ESVB 825471/005 2018-05-22 2019-05-21 Receiver Schwarz SEMT-1008 Amplifier Agilent 8447F 3113A06717 2018-05-22 2019-05-21 SEMT-1043 Amplifier C&D PAP-1G18 2002 2018-05-22 2019-05-21 Broadband SEMT-1011 Schwarz beck VULB9163 9163-333 2017-06-08 2020-06-07 Antenna SEMT-1042 Horn Antenna ETS 3117 00086197 2017-06-08 2020-06-07 SEMT-1121 Horn Antenna Schwarzbeck BBHA 9170 BBHA9170582 2017-06-08 2020-06-07 SEMT-1069 Loop Antenna Schwarz beck FMZB 1516 9773 2017-06-08 2020-06-07 EMI Test Rohde & SEMT-1001 ESPI 101611 2018-05-22 2019-05-21 Receiver Schwarz SEMT-1003 L.I.S.N Schwarz beck NSLK8126 8126-224 2018-05-22 2019-05-21 Rohde & SEMT-1002 Pulse Limiter ESH3-Z2 100911 2018-05-22 2019-05-21 Schwarz Direction SEMT-1168 Pre-amplifier PAP-0126 14141-12838 2018-05-22 2019-05-21 Systems Inc. Direction SEMT-1169 Pre-amplifier PAP-2640 14145-14153 2018-05-22 2019-05-21 Systems Inc. Spectrum Rohde & SEMT-1163 FSP40 100612 2018-05-22 2019-05-21 Analyzer Schwarz DRG Horn A.H. SEMT-1170 SAS-574 571 2018-03-19 2021-03-18 Antenna SYSTEMS SEMT-1166 Power Limiter Agilent N9356B MY45450376 2018-05-22 2019-05-21 SEMT-1048 RF Limiter ATTEN AT-BSF-2400~2500 / 2018-05-22 2019-05-21 SEMT-1076 RF Switcher Top Precision RCS03-A2 / 2018-05-22 2019-05-21 SEMT-C001 Cable Zheng DI LL142-07-07-10M(A) / 2018-03-19 2019-03-18 SEMT-C002 Cable Zheng DI ZT40-2.92J-2.92J-6M / 2018-03-19 2019-03-18 SEMT-C003 Cable Zheng DI ZT40-2.92J-2.92J-2.5M / 2018-03-19 2019-03-18 SEMT-C004 Cable Zheng DI 2M0RFC / 2018-03-19 2019-03-18 SEMT-C005 Cable Zheng DI 1M0RFC / 2018-03-19 2019-03-18 SEMT-C006 Cable Zheng DI 1M0RFC / 2018-03-19 2019-03-18 Report No.: STR18108061I-5 Page 6 of 34 FCC Part 15.247

Model: L465 2. SUMMARY OF TEST RESULTS FCC Rules Description of Test Item Result § 2.1093 RF Exposure Compliant §15.203;§15.247(b)(4)(i) Antenna Requirement Compliant §15.205 Restricted Band of Operation Compliant §15.207(a) Conducted Emission Compliant §15.247(e) Power Spectral Density Compliant §15.247(a)(2) DTS Bandwidth Compliant §15.247(b)(3) RF Output Power Compliant §15.209(a) Radiated Emission Compliant §15.247(d) Band Edge (Out of Band Emissions) Compliant N/A: not applicable Report No.: STR18108061I-5 Page 7 of 34 FCC Part 15.247

Model: L465 3. RF Exposure 3.1 Standard Applicable According to§1.1307 and §2.1093, the portable transmitter must comply the RF exposure requirements. 3.2 Test Result This product complied with the requirement of the RF exposure, please see the SAR Report. Report No.: STR18108061I-5 Page 8 of 34 FCC Part 15.247

Model: L465 4. Antenna Requirement 4.1 Standard Applicable According to FCC Part 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. 4.2 Evaluation Information This product has a Integral antenna, fulfill the requirement of this section. Report No.: STR18108061I-5 Page 9 of 34 FCC Part 15.247

Model: L465 5. Power Spectral Density 5.1 Standard Applicable According to 15.247(a)(1)(iii), For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. 5.2 Test Procedure According to the KDB 558074 D01 v05 Subclause 8.4 and ANSI C63.10-2013 Subclause 11.10.2, the test method of power spectral density as below: a) Set analyzer center frequency to DTS channel center frequency. b) Set the span to 1.5 times the DTS bandwidth. c) Set the RBW to: 3 kHz ≤ RBW ≤ 100 kHz. d) Set the VBW ≥ 3 × RBW. e) Detector = peak. f) Sweep time = auto couple. g) Trace mode = max hold. h) Allow trace to fully stabilize. i) Use the peak marker function to determine the maximum amplitude level within the RBW. j) If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. 5.3 Summary of Test Results/Plots Power Spectral Density Limit Test Mode Test Channel dBm/3kHz dBm/3kHz Low -17.68 8 GFSK(BLE) Middle -17.29 8 High -15.39 8 Please refer to the following test plots: Report No.: STR18108061I-5 Page 10 of 34 FCC Part 15.247

Model: L465 Low Middle High Report No.: STR18108061I-5 Page 11 of 34 FCC Part 15.247

Model: L465 6. DTS Bandwidth 6.1 Standard Applicable According to 15.247(a)(2). Systems using digital modulation techniques may operate in the 902–928 MHz, 2400– 2483.5 MHz, and 5725–5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 6.2 Test Procedure According to the KDB 558074 D01 v05 Subclause 8.2 and ANSI C63.10-2013 Subclause 11.8.1, the test method of DTS Bandwidth as below: a) Set RBW = 100 kHz. b) Set the video bandwidth (VBW) ≥ 3 × RBW. c) Detector = Peak. d) Trace mode = max hold. e) Sweep = auto couple. f) Allow the trace to stabilize. g) Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. 6.3 Summary of Test Results/Plots 6 dB Bandwidth Limit Test Mode Test Channel kHz kHz Low 713.837 ≥500 GFSK(BLE) Middle 712.136 ≥500 High 701.201 ≥500 Please refer to the following test plots: Report No.: STR18108061I-5 Page 12 of 34 FCC Part 15.247

Model: L465 Low Middle High Report No.: STR18108061I-5 Page 13 of 34 FCC Part 15.247

Model: L465 7. RF Output Power 7.1 Standard Applicable According to 15.247(b)(3). For systems using digital modulation in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz bands: 1 Watt. 7.2 Test Procedure According to the KDB-558074 D01 v05 Subclause 8.3.1.1 and ANSI C63.10-2013 Subclause 11.9.1.1, this procedure shall be used when the measurement instrument has available a resolution bandwidth that is greater than the DTS bandwidth. a) Set the RBW ≥ DTS bandwidth. b) Set VBW ≥ 3 × RBW. c) Set span ≥ 3 x RBW d) Sweep time = auto couple. e) Detector = peak. f) Trace mode = max hold. g) Allow trace to fully stabilize. h) Use peak marker function to determine the peak amplitude level. 7.3 Summary of Test Results/Plots Reading Output Power Limit Test Mode Test Channel dBm mW mW Low -3.102 0.490 1000 GFSK(BLE) Middle -2.704 0.537 1000 High -0.614 0.868 1000 Report No.: STR18108061I-5 Page 14 of 34 FCC Part 15.247

Model: L465 Low Middle High Report No.: STR18108061I-5 Page 15 of 34 FCC Part 15.247

Model: M L465 8. Field S Strength of o Spurio ous Emissiions 8.1 Standaard Applicaable According too §15.247(d)), in any 100 kHz bandwiddth outside th he frequency band in whicch the spread d spectrum orr digitally moodulated intenntional radiato or is operatinng, the radio frequency f powwer that is prroduced by thhe intentionall radiator shalll be at least 20 2 dB below that in the 1000 kHz bandw width within the t band that contains the highest levell of the desirred power, based on eith her an RF coonducted or a radiated measurement, m provided the transmitterr demonstratees compliancee with the peeak conductedd power limiits. If the transmitter com mplies with thhe conductedd power limitss based on thhe use of RMS averaging oover a time in nterval, as peermitted undeer paragraph (b)(3) of thiss section, the attenuation required r undder this paraggraph shall be 30 dB insttead of 20 dB B. Attenuatioon below thee general limiits specified ini §15.209(a)) is not requiired. In addittion, radiated emissions w which fall in the t restrictedd bands, as defined in §15.205(a), must also comply with the radiiated emission n limits speciified in §15.2 209(a). The emission limit in thiss paragraph iss based on m measurement in nstrumentatio on employingg an average detector. d The provisions inn §15.35 for limiting l peak k emissions appply. Spuriou us Radiated Emissions meaasurements sttarting below or at tthe lowest cryystal frequency. 8.2 Test Prrocedure The setup off EUT is according with per p ANSI C663.10-2013 measurement m procedure. p Thhe specificatiion used wass with the FCCC Part 15.2055 15.247(a) an nd FCC Part 15.209 Limitt. The externall I/O cables were w draped along a the test table and forrmed a bundlee 30 to 40 cm m long in the middle. m The spacingg between the peripherals was w 10 cm. Report No.: S STR181080611I-5 Page 16 of 34 3 FCC C Part 15.247

Model: L465 Antenna Tower 1m-4m 3m EUT SYS 1.5m Turntable Table To EMI Receiver Ground Plane Frequency :9kHz-30MHz Frequency :30MHz-1GHz Frequency :Above 1GHz RBW=10KHz, RBW=120KHz, RBW=1MHz, VBW =30KHz VBW=300KHz VBW=3MHz(Peak), 10Hz(AV) Sweep time= Auto Sweep time= Auto Sweep time= Auto Trace = max hold Trace = max hold Trace = max hold Detector function = peak Detector function = peak, QP Detector function = peak, AV 8.3 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and the Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading + Ant. Factor + Cable Loss – Ampl. Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -6dBV means the emission is 6dBV below the maximum limit. The equation for margin calculation is as follows: Margin = Corr. Ampl. – FCC Part 15 Limit 8.4 Summary of Test Results/Plots Note: this EUT was tested in 3 orthogonal positions and the worst case position data was reported. Report No.: STR18108061I-5 Page 17 of 34 FCC Part 15.247

Model: L465  Spurious Emissions Below 1GHz Test Channel Low Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) (  ) (cm) 1 47.8260 36.39 -12.79 23.60 40.00 -16.40 217 100 peak 2 106.3850 34.03 -14.00 20.03 43.50 -23.47 100 100 peak 3 343.1800 31.70 -6.51 25.19 46.00 -20.81 278 100 peak 4 962.1623 30.89 3.14 34.03 54.00 -19.97 118 100 peak Report No.: STR18108061I-5 Page 18 of 34 FCC Part 15.247

Model: L465 Test Channel Low Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) (  ) (cm) 1 49.3594 36.07 -12.88 23.19 40.00 -16.81 342 100 peak 2 105.2718 35.01 -14.03 20.98 43.50 -22.52 96 100 peak 3 381.2487 32.28 -6.60 25.68 46.00 -20.32 338 100 peak 4 993.0114 30.02 3.93 33.95 54.00 -20.05 96 100 peak Report No.: STR18108061I-5 Page 19 of 34 FCC Part 15.247

Model: L465 Test Channel Middle Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) (  ) (cm) 1 48.3318 35.77 -12.79 22.98 40.00 -17.02 292 100 peak 2 97.1148 34.94 -14.90 20.04 43.50 -23.46 268 100 peak 3 419.1081 31.22 -6.12 25.10 46.00 -20.90 71 100 peak 4 1000.0000 29.54 4.04 33.58 54.00 -20.42 175 100 peak Report No.: STR18108061I-5 Page 20 of 34 FCC Part 15.247

Model: L465 Test Channel Middle Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) (  ) (cm) 1 47.6586 36.51 -12.80 23.71 40.00 -16.29 75 100 peak 2 98.8326 34.30 -14.64 19.66 43.50 -23.84 113 100 peak 3 346.8092 31.98 -6.49 25.49 46.00 -20.51 87 100 peak 4 989.5355 29.53 3.88 33.41 54.00 -20.59 102 100 peak Report No.: STR18108061I-5 Page 21 of 34 FCC Part 15.247

Model: L465 Test Channel High Polarity: Horizontal No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) (  ) (cm) 1 46.9948 35.36 -12.84 22.52 40.00 -17.48 175 100 peak 2 115.7256 35.28 -14.89 20.39 43.50 -23.11 113 100 peak 3 336.0352 32.37 -6.62 25.75 46.00 -20.25 134 100 peak 4 975.7529 30.55 3.53 34.08 54.00 -19.92 102 100 peak Report No.: STR18108061I-5 Page 22 of 34 FCC Part 15.247

Model: L465 Test Channel High Polarity: Vertical No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) (  ) (cm) 1 48.6719 35.33 -12.82 22.51 40.00 -17.49 75 100 peak 2 106.7587 34.40 -14.00 20.40 43.50 -23.10 133 100 peak 3 336.0352 31.97 -6.62 25.35 46.00 -20.65 103 100 peak 4 986.0717 30.39 3.82 34.21 54.00 -19.79 118 100 peak Report No.: STR18108061I-5 Page 23 of 34 FCC Part 15.247

Model: L465  Spurious Emissions Below 1GHz Frequency Reading Correct Result Limit Margin Polar Detector (MHz) (dBuV/m) dB (dBuV/m) (dBuV/m) (dB) H/V Low Channel-2402MHz 4804 60.8 -3.59 57.21 74 -16.79 H PK 4804 41.79 -3.59 38.2 54 -15.8 H AV 7206 61.51 -0.52 60.99 74 -13.01 H PK 7206 38.21 -0.52 37.69 54 -16.31 H AV 4804 61.74 -3.59 58.15 74 -15.85 V PK 4804 41.6 -3.59 38.01 54 -15.99 V AV 7206 61.22 -0.52 60.7 74 -13.3 V PK 7206 40.08 -0.52 39.56 54 -14.44 V AV Middle Channel-2440MHz 4880 61.47 -3.49 57.98 74 -16.02 H PK 4880 38.91 -3.49 35.42 54 -18.58 H AV 7320 61.58 -0.47 61.11 74 -12.89 H PK 7320 38.18 -0.47 37.71 54 -16.29 H AV 4880 59.83 -3.49 56.34 74 -17.66 V PK 4880 40.09 -3.49 36.6 54 -17.4 V AV 7320 59.18 -0.47 58.71 74 -15.29 V PK 7320 41.79 -0.47 41.32 54 -12.68 V AV High Channel-2480MHz 4960 59.24 -3.41 55.83 74 -18.17 H PK 4960 38.31 -3.41 34.9 54 -19.1 H AV 7440 60.25 -0.42 59.83 74 -14.17 H PK 7440 40.06 -0.42 39.64 54 -14.36 H AV 4960 60.76 -3.41 57.35 74 -16.65 V PK 4960 41.11 -3.41 37.7 54 -16.3 V AV 7440 58.24 -0.42 57.82 74 -16.18 V PK 7440 40.41 -0.42 39.99 54 -14.01 V AV Note: Testing is carried out with frequency rang 9kHz to the tenth harmonics, other than listed in the table above are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. Report No.: STR18108061I-5 Page 24 of 34 FCC Part 15.247

Model: L465 9. Out of Band Emissions 9.1 Standard Applicable According to §15.247 (d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a). 9.2 Test Procedure According to the KDB 558074D01 v05 Subclause 8.4 and ANSI C63.10-2013 Subclause 11.11, the Emissions in nonrestricted frequency bands test method as follows: a) Set the center frequency and span to encompass frequency range to be measured. b) Set the RBW = 100 kHz. c) Set the VBW ≥ [3 × RBW]. d) Detector = peak. e) Sweep time = auto couple. f) Trace mode = max hold. g) Allow trace to fully stabilize. h) Use the peak marker function to determine the maximum amplitude level. According to the KDB 558074 D01 v05 Subclause 8.5 and ANSI C63.10-2013 Subclause 11.12, the Emissions in restricted frequency bands test method as follows: A. Radiated emission measurements: Set span = wide enough to capture the peak level of the emission operating on the channel closest to the bandedge, as well as any modulation products which fall outside of the authorized band of operation (2310MHz to 2420MHz for low bandedge, 2460MHz to 2500MHz for the high bandedge) RBW = 1MHz, VBW = 1MHz for peak value measured RBW = 1MHz, VBW = 10Hz for average value measured Sweep = auto; Detector function = peak/average; Trace = max hold All the trace to stabilize, set the marker on the emission at the bandedge, or on the highest modulation product outside of the band, if this level is greater than that at the bandedge. Enable the marker-delta function, then use the marker-to-peak function to move the marker to the peak of the in-band emission. Those emission must comply with the 15.209 limit for fall in the restricted bands listed in section 15.205. Note that the method of measurement KDB publication number: 913591 may be used for the radiated bandedge measurements. Report No.: STR18108061I-5 Page 25 of 34 FCC Part 15.247

Model: L465 B. Antenna-port conducted measurements Peak emission levels are measured by setting the instrument as follows: a) RBW = as specified in Table 9/ b) VBW ≥ [3 × RBW]. c) Detector = peak. d) Sweep time = auto. e) Trace mode = max hold. f) Allow sweeps to continue until the trace stabilizes. (Note that the required measurement time may be lengthened for low-duty-cycle applications.) If the peak-detected amplitude can be shown to comply with the average limit, then it is not necessary to perform a separate average measurement. Ensure that the amplitude of all unwanted emissions outside of the authorized frequency band (excluding restricted frequency bands) are attenuated by at least the minimum requirements specified in section 8.1. Report the three highest emissions relative to the limit. 9.3 Summary of Test Results/Plots Report No.: STR18108061I-5 Page 26 of 34 FCC Part 15.247

Model: L465  Radiated test Test Channel Low Polarity: Horizontal (worst case) No. Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV/m) Factor(dB) (dBuV/m) (dBuV/m) (dB) 1 2310.000 42.26 -7.78 34.48 54.00 -19.52 Average Detector 2310.000 54.79 -7.78 47.01 74.00 -26.99 Peak Detector 2 2390.000 41.80 -7.32 34.48 54.00 -19.52 Average Detector 2390.000 54.23 -7.32 46.91 74.00 -27.09 Peak Detector 3 2402.047 91.69 -7.25 84.44 / / Average Detector 2401.640 98.58 -7.25 91.33 / / Peak Detector Report No.: STR18108061I-5 Page 27 of 34 FCC Part 15.247

Model: L465 Test Channel High Polarity: Horizontal (worst case) No. Frequency Reading Correct Result Limit Margin Remark (MHz) (dBuV/m) dB/m (dBuV/m) (dBuV/m) (dB) 1 2480.154 93.31 -6.78 86.53 / / Average Detector 2479.731 101.12 -6.79 94.33 / / Peak Detector 2 2483.500 54.33 -6.77 47.56 54.00 -6.44 Average Detector 2483.500 62.57 -6.77 55.80 74.00 -18.20 Peak Detector 3 2500.000 40.95 -6.67 34.28 54.00 -19.72 Average Detector 2500.000 54.06 -6.67 47.39 74.00 -26.61 Peak Detector Report No.: STR18108061I-5 Page 28 of 34 FCC Part 15.247

Model: L465  Conducted test Low Report No.: STR18108061I-5 Page 29 of 34 FCC Part 15.247

Model: L465 Middle Report No.: STR18108061I-5 Page 30 of 34 FCC Part 15.247

Model: L465 High Report No.: STR18108061I-5 Page 31 of 34 FCC Part 15.247

Model: L465 10. Conducted Emissions 10.1 Test Procedure The setup of EUT is according with per ANSI C63.4-2014 measurement procedure. The specification used was with the FCC Part 15.207 Limit. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. 10.2 Basic Test Setup Block Diagram Adapter EUT LISN 1.0 m 1.5 To Receiver Non-conduction table 80 cm above Ground Plane 1. 5 m 10.3 Test Receiver Setup During the conducted emission test, the test receiver was set with the following configurations: Start Frequency .......................................................................... 150 kHz Stop Frequency .......................................................................... 30 MHz Sweep Speed .............................................................................. Auto IF Bandwidth.............................................................................. 10 kHz Quasi-Peak Adapter Bandwidth ................................................. 9 kHz Quasi-Peak Adapter Mode ......................................................... Normal 10.4 Summary of Test Results/Plots Report No.: STR18108061I-5 Page 32 of 34 FCC Part 15.247

Model: M L465 Test Moode Coommunication n AC1200V 60Hz Polarrity: Neu utral No. Frequency y Readin ng Corrrect Re esult Limit Margin Detector (MHz) (dBuV V) (dB//m) (dBuV) (dBuV) ( (dB) 1 0.1620 38.13 3 10. 10 48 8.23 65.36 -17.13 QP 2 0.1620 20.15 5 10. 10 30 0.25 55.36 -25.11 AVG 3 0.3500 33.84 4 10.2 22 44 4.06 58.96 -14.90 QP 4* 0.3500 24.00 0 10.2 22 34 4.22 48.96 -14.74 AVG 5 0.4460 30.33 3 10.2 27 40 0.60 56.95 -16.35 QP 6 0.4460 17.50 0 10.2 27 27 7.77 46.95 -19.18 AVG Report No.: S STR181080611I-5 Page 33 of 34 3 FCC C Part 15.247

Model: M L465 Test Moode Coommunication n AC1200V 60Hz Polarrity: Liine No. Frequency y Readin ng Corrrect Re esult Limit Margin Detector (MHz) (dBuV V) (dB//m) (dBuV) (dBuV) ( (dB) 1 0.1620 32.84 4 10. 10 42 2.94 65.36 -22.42 QP 2* 0.3540 21.16 6 10.2 22 31.38 48.87 -17.49 AVG 3 0.3900 18.92 2 10.2 25 29 9.17 48.06 -18.89 AVG 4 0.4100 29.41 1 10.2 25 39 9.66 57.65 -17.99 QP 5 0.5820 26.94 4 10. 33 37 7.27 56.00 -18.73 QP 6 0.7380 13.41 1 10.4 41 23 3.82 46.00 -22.18 AVG ***** EN ND OF REPO ORT ***** Report No.: S STR181080611I-5 Page 34 of 34 3 FCC C Part 15.247


Document Created: 2018-11-14 12:20:08
Document Modified: 2018-11-14 12:20:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC