User Manual

FCC ID: RPV-SE5901B-AF

Users Manual

Download: PDF
FCCID_4185189

Inside the package you will find the following items: Front View 3G DB9 Type 4G DB9 Type 3G IO Type 4G IO Type  Industrial 3G/4G Serial Gateway x 1 or  Industrial 3G/4G Modbus Gateway x 1 or 1~4 1~4 1~4 1~4  Industrial 3G/4G Modbus Concentrator x 1 or  Industrial 3G/4G Protocol Gateway x 1  3-Pin 5.08mm Lockable Terminal Block 5 5 6 6 (Already mounted to the device) x 1 Industrial Cellular Serial Device Server  2x7 Pin 3.5mm Lockable Terminal Block (IO version only) x 1 7~10 7~10 Industrial Cellular Modbus Gateway  DIN-Rail Kit (Already mounted to the device) x 1 11 11 11 11 ground the device properly Industrial Cellular Modbus Concentrator  Installation Guide with Warranty Card x 1 12 12 12 12 Industrial Cellular Protocol Gateway Never install or work on electrical or cabling during periods of 13 13 13 13 lightning activity. 14 14 Never connect or disconnect power when hazardous gases are present. SE5901B/MB5901B/PG5901B Series Warning:Hot Surface Do Not Touch. 1. PWR LED 7. Relay2 LED This equipment should be installed indoor and not connect directly 2. RUN LED 8. Relay1 LED Indoor with equipment installed outdoor. 3. COM1 Tx LED 9. DI2 LED 3. Proceed then to fix the antennas to the 4. COM1 Rx LED 10. DI1 LED This device complies with part 15 of the FCC Rules. female RP-SMA connectors deemed to Version V1.2 Operation is subject to the following two conditions: 5. 9-Pin Male D-Sub Connector 11. Default Button (Fig. 3). You can then choose whether (1) This device may not cause harmful interference, and for RS-232/485 12. PWR USB Updated in December, 2018 (2) This device must accept any interference received, including to plug in the I/O ports at this point or do 6. 14-Pin 3.5 mm Terminal Block 13. 10/100/1000 BASE-T(X) Ports interference that maycause undesired operation. for RS-232/485(COM1), it later depending on the actual location 14. SMA Connector for Antenna RS-232(COM2), Relay, and DI of the device or level of comfort for Notice: (D3G version only) 3 Any changes or modifications not expressly approved by the party responsible performing such operation. for compliance could void your authority to operate the equipment. 1 1 NOTE: TOP View Bottom View This equipment has been tested and found to comply with the limits for a 1. Grounding Screw Class B digitaldevice, pursuant to part 15 of the FCC Rules. 4 2. SMA Connector for Antenna These limits are designed to provide reasonable protection against harmful 5 3 (4G version only) interference in a residential installation. 4 3. Frame Ground 2 2 This equipment generates, uses and can radiate radio frequency energy and, 4 5 if not nstalled and used in accordance with the instructions, may cause 4. Terminal for Power 1 harmful interference to radio communications. 5 5. USB2 5. However, there is no guarantee that interference will not occur in a particular 6. PWR Reset 2 6 7 installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off 7. SMA Connector for Antenna and on, the user is encouraged to try to correct the interference by one or (4G version only) more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. The device's The antenna(s) used for this transmitter must not be co-located of operating in conjunction with any other antenna or transmitter. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Ln order to avoid the possibility of exceeding the Fcc radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8inches) during normal operation. 89900500G

Warranty Policy Warranty Conditions Front View Products supplied by Atop Technologies are covered in this warranty for Blinking COM port is transmitting data sub-standard performance or defective workmanship. The warranty is not, COM-TX Green Off COM port is not transmitting data SE/MB/PG5901B SE/MB/PG5901B SE/MB/PG5901B SE/MB/PG5901B however, extended to goods damaged in the following circumstances: -D3G -4G -IO-D3G -IO-4G Blinking COM port is receiving data (a) Excessive forces or impacts COM-RX Green Off COM port is not receiving data (b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake On Ethernet is transmitting at 1Gbps (c) Use of unqualified power supply, connectors, or unauthorized parts/kits (d) Replacement with unauthorized parts Orange Blinking Ethernet is transmitting at 100Mbps (Speed) slowly RMA and Shipping Costs Reimbursement LAN Customers shall always obtain an authorized "RMA" number from Atop before Off Ethernet is transmitting at 10Mbps shipping the goods to be repaired to Atop. When in normal use, a sold product Green Blinking Ethernet data is transmitting shall be replaced with a new one within 3 months after purchase. The shipping (Data) Off Ethernet no data transmit cost from the customer to Atop will be reimbursed by Atop. On Power is being supplied Power Green After 3 months and still within the warranty period, it is up to Atop whether to Off Power is not supplied replace the unit with a new one; normally, as long as a product is under warranty, Blinking AP Firmware is running normally all parts and labor are free of charge to the customers. 9-Pin Male D-Sub Connector for RS-232/485 RUN Green On/Off System is not ready or halt After the warranty period, the customer shall cover the cost for parts and labor.Three months after purchase, the shipping cost from the customer to Atop – will not be reimbursed, but the shipping cost from Atop to the customer will be – paid by Atop. – Limited Liability Top View Bottom View Atop shall not be held responsible for any consequential losses from using Atop’s – product. Warranty Period 32 – Product Categories Warranty Product Categories Warranty – Ethernet Switches DIN-Rail Power Supplies 3 years Wireless 2 x 7-pin Male Terminal Block for RS-232/485(COM 1), Serial Device Servers Power Adaptors RS-232(COM 2) Relay and DI Modbus Gateways 5 Years Assignment Assignment Side View Rear View Protocol Gateways Antennas 1 years 1 DI1 8 Rx1 1 2 3 4 5 6 7 Media Converters 2 DI2 9 CTS 18,5 Other Accessories 3 RY1c 10 Tx1/D+ Embedded Device Servers 4 RY1+ 11 RTS/D- The warranty certification will not be effective until an authorized stamp issued by 5 RY2c 12 SG Atop’s overseas agents. 6 RY2+ 13 Rx2 Purchase Date: / / (yyyy/mm/dd) 8 9 10 11 12 13 14 7 SG 14 Tx2 Serial Number Relay Output with current carrying capacity of 1A@30 VDC (Normal open) Pin Assignments and Connections 121,5 134,6 48,3 107 122,6 10/100/1000BASE-T(X) Ethernet Pinout Atop Customer Services and Supports 1. Please contact your local dealers or Atop Technical Support Center at the following numbers. + 886-3-550-8137 (Atop Taiwan) + 86-21-6495-6232 (Atop China) 10/100Base-T(X) 2. Please report the defected problems via Atop’s Web site or E-mail account Web Site：www.atop.com.tw, e-mail：service@atop.com.tw Web Site：www.atop.com.cn, e-mail：service@atop.com.cn 12,5 90 3. Company Addr: 2F, No. 146, Sec. 1, Tung-Hsing Rd., Jubei, Hsinchu 30261, 1000Base-T(X) 31,5 Taiwan, R.O.C. Manufacturer Addr: 1st FL 30 R&D RD II,SCIENCE-BASED INDUSTRIAL PARK,HSINCHU 300 TAIWAN, R.O.C ─ Any changes to this material will be announced on Atop website. ─


Document Created: 2019-02-27 16:57:24
Document Modified: 2019-02-27 16:57:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC