Test Report

FCC ID: RPNE5KTX10046340

Test Report

Download: PDF
FCCID_391853

Königswinkel 10 32825 Blomberg Germany Phone +49 5235 9500-0 Fax +49 5235 9500-10 Test Report Reference: R30764 TX Edition 3 Equipment under Test: Evolution 5000 Transmitter FCC ID: RPNE5KTX1004634 Applicant: MSA Auer GmbH Manufacturer: VTQ Videotronik GmbH Test Laboratory (CAB) accredited by DATech e.V. in compliance with DIN EN ISO/IEC 17025 under the Reg. No. TTI-P-G071/94-11 and listed by FCC 31040/SIT1300F2

TEST REPORT REFERENCE: R30764 TX Edition 3 Contents: Page 1 IDENTIFICATION..................................................................................................................................... 3 1.1 APPLICANT .................................................................................................................................... 3 1.2 MANUFACTURER.......................................................................................................................... 3 1.3 DATES ............................................................................................................................................ 3 1.4 TEST LABORATORY ..................................................................................................................... 4 1.5 RESERVATION .............................................................................................................................. 4 1.6 NORMATIVE REFERENCES ......................................................................................................... 4 1.7 TEST RESULTS ............................................................................................................................. 4 2 TECHNICAL DATA OF EQUIPMENT...................................................................................................... 5 2.1 DEVICE UNDER TEST................................................................................................................... 5 2.2 PEREPHERY DEVICES ................................................................................................................. 5 2.3 MODIFICATIONS ........................................................................................................................... 5 3 OPERATIONAL STATES AND PHYSICAL BOUNDARIES .................................................................... 6 4 LIST OF MEASUREMENTS .................................................................................................................... 7 RADIATED EMISSIONS (TRANSMITTER).......................................................................................... 8 4.1.1 METHOD OF MEASUREMENT ......................................................................................... 8 4.2 FREQUENCY STABILITY WITH RESPECT TO AMBIENT TEMPERATURE AND SUPPLY VOLTAGE ................. 13 4.2.1 TEST RESULTS (POWER OUTPUT CONDUCTED)........................................................ 14 4.2.2 TEST RESULTS (POWER OUTPUT RADIATED) ............................................................ 16 4.2.3 TEST RESULTS (SPURIOUS EMISSIONS RADIATED) .................................................. 18 4.3 FREQUENCY STABILITY / VOLTAGE VARIATION ...................................................................... 26 4.4 FREQUENCY STABILITY / TEMPERATURE VARIATION............................................................ 27 4.5 OCCUPIED BANDWIDTH .............................................................................................................. 28 5 TEST EQUIPMENT AND ANCILLARIES USED FOR TESTS ................................................................ 29 6 LIST OF ANNEXES ................................................................................................................................. 33 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 2 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 1 IDENTIFICATION 1.1 APPLICANT Name: MSA AUER GmbH Address: Thielemannstraße 1 12059 Berlin Country: Germany Name for contact purposes: - Phone: - Fax: - Mail address: - Applicant represented during - the test by the following person: 1.2 MANUFACTURER Name: VTQ Videotronik GmbH Address: Grüne Straße 2 06268 Querfurt Country: Germany Name for contact purposes: Mr. Richter Phone: +49-(0)34771-5189 Fax: +49-(0)34771-22044 Mail address: h.richter@vtq.de Applicant represented during Mr. Richter the test by the following person: 1.3 DATES Date of receipt of test sample: 24 September 2003 Start of test: 24 September 2003 End of test: 26 September 2003 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 3 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 1.4 TEST LABORATORY The tests were carried out at: PHOENIX TEST-LAB GmbH Königswinkel 10 D-32825 Blomberg Phone: +49 (0) 52 35 / 95 00-0 Germany Fax: +49 (0) 52 35 / 95 00-10 accredited by DATech e.V. in compliance with DIN EN ISO/IEC 17025 under Reg. No. TTI-P-G071/94-11 and listed by FCC 31040/SIT1300F2. Test engineer: Raimund Blask 3 December 2003 name signature date Test report checked: Bernd Steiner 3 December 2003 name signature date stamp 1.5 RESERVATION This test report is only valid in its original form. Any reproduction of its contents without written permission of the accredited test laboratory PHOENIX TEST-LAB GmbH is prohibited. The test results herein refer only to the tested sample. PHOENIX TEST-LAB GmbH is not responsible for any generalisations or conclusions drawn from these test results concerning further samples. Any modification of the tested samples is prohibited and leads to the invalidity of this test report. Each page necessarily contains the PHOENIX TEST-LAB Logo and the TEST REPORT REFERENCE. 1.6 NORMATIVE REFERENCES [1] ANSI C63.4 (1992) American National Standard for Methods of Measuring of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. [2] FCC 47 CFR Part 90 (October 2003), Private Land Mobile Radio Service [3] FCC 47 CFR Part 2 (October 2003) 1.7 TEST RESULTS The requirements of this test document are fulfilled by the equipment under test. The complete test results are presented in the following. Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 4 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 2 TECHNICAL DATA OF EQUIPMENT 2.1 DEVICE UNDER TEST Type of equipment: 2.4 GHz video-transmitter Type designation: Evolution 5000 Transmitter Highest operating frequency 2474 MHz * declared by the applicant The following external I/O cables were used: Cable Length Shielding Connector DC-power-supply 1.5 m no Not specified Video-Signal-Generator 1.5 m yes BNC 2.2 PERIPHERY DEVICES The ancillary equipment mentioned below was in use: The EUT (transmitter) was powered with an external DC-power supply. Acol ourTVpat ter ngener at orTy pe“Phil ipsPM 5418”wasusedt ogener atea“ col ourbar ” (according to CCIR 405, 525 lines NTSC video) to modulate the transmitter. 2.3 MODIFICATIONS No modifications were necessary to fulfil the requirements. Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 5 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 3 OPERATIONAL STATES AND PHYSICAL BOUNDARIES The EUT (transmitter) was powered with an external DC-power supply. Acol ourTVpat terngener atorTy pe“ Phili psPM 5418”wasusedt ogener atea“ col ourbar ” (according to CCIR 405, 525 lines NTSC video) to modulate the transmitter. The modulation signal-amplitude to the EUT was 2 V (peak to peak). The transmitter was tested on the following frequencies: Channel: Transmit frequency: 1 2458 MHz 2 2474 MHz The physical boundaries of the Equipment Under Test are shown below. Physical boundaries of the EUT EUT Video- signal- generator Power- Supply Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 6 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 4 LIST OF MEASUREMENTS No. Test: Procedure: Subpart of test report: Result: 1 RF power output Conducted at the antenna 4.2.1 Passed connector (unmodulated) 2 RF-power output Radiated (modulated with 4.2.2 Passed normal modulation) 3 Spurious emission Radiated (modulated with 4.2.3 Passed normal modulation) 4 Spurious emission Radiated (modulated with - - normal modulation) 5 Frequency stability Voltage variation 4.3 Passed (unmodulated) 6 Frequency stability Temperature variation 4.4 Passed (unmodulated) 7 Occupied bandwidth Radiated (Coupling unit) 4.5 Passed (modulated with NTSC- colour-bar-signal) Remark: The conducted spurious emission measurement was not applicable because of an integral antenna without commercial connector. Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 7 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 RADIATED EMISSIONS (TRANSMITTER) 4.1.1 METHOD OF MEASUREMENT The radiated emission measurement is subdivided in two stages. Preliminary measurement: In the first stage a preliminary measurement will be performed in a fully anechoic chamber with a measuring distance of 3 meter. Tabletop devices will set up on a non-conducting support with a size of 1 m by 1.5 m and a height of 80 cm. Floor-standing devices will be placed directly on the turntable/ground plane. The set up of the Equipment under test will be in accordance to ANSI C63.4-1992 [1]. The frequency range 30 MHz to 1 GHz will be measured with an EMI Receiver set to MAX Hold mode and a resolution bandwidth of 120 kHz. The frequency range 1 GHz to 26 GHz will be measured with an EMI Receiver set to MAX Hold mode and a resolution bandwidth of 1 GHz. The measurement will be performed in horizontal and vertical polarisation of the measuring antenna and while rotating the EUT in its vertical axis in the range of 0° to 360° and three orthogonal axis. The resolution bandwidth of the EMI Receiver will be set to the following values: Frequency range Resolution bandwidth 30 MHz to 230 MHz 100 kHz 230 MHz to 1 GHz 100 kHz 1 GHz to 26 GHz 1 MHz 3m EUT 1.5 m 0.8 m EMI- Receiver Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 8 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Procedure of preliminary measurement: Prescans were performed in the frequency range 30 MHz to 200 MHz, 200 MHz to 1 GHz, 1 GHz to 4 GHz, 4 GHz to 12 GHz, 12 GHz to 18 GHz and 18 GHz to 26 GHz. The following procedure will be used: 1) Monitor the frequency range at horizontal polarisation and a EUT azimuth of 0° 2) Manipulate the system cables within the range to produce the maximum level of emission 3) Rotate the EUT by 360° to maximize the detected signals. 4) Make a hardcopy of the spectrum 5) Measure the frequency of 3 highest detected emissions with a lower span and resolution bandwidth to increase the accuracy and note the frequency value. 6) Repeat steps 1) to 4) with the other orthogonal axes 7) Repeat steps 1) to 5) with the vertical polarisation of the measuring antenna. Final Measurement (30 MHz to 1 GHz): In the second stage a final measurement will be performed on selected frequencies found in the preliminary measurement. The final measurement in the frequency range 30 MHz to 1 GHz was done on an open area test site during this test the EUT will be rotated in three orthogonal axis in the range of 0° to 360°, the measuring antenna will be set to horizontal and vertical polarisation and raised and lowered in the range from 1 m to 4 m to find the maximum level of emissions. The final measurement in the frequency range 1 GHz to 26 GHz was done in the fully anechoic chamber. During this test the EUT will be rotated in three orthogonal axis in the range of 0° to 360°, the measuring antenna will be set to horizontal and vertical polarisation to find the maximum level of emissions. The resolution bandwidth of the EMI Receiver will be set to the following values: Frequency range Resolution bandwidth 30 MHz to 1 GHz 120 kHz 1 GHz to 26 GHz 1 MHz Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 9 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Measuring distance 1 m to 4 m EUT 0.8 m Ground plane EMI- Receiver Procedure of final measurement: The following procedure will be used: 1) Measure on the selected frequencies at an antenna height of 1 m and a EUT azimuth of 23° 2) Move the antenna from 1 m to 4 m and note the maximum value at each frequency. 3) Rotate the EUT by 45° and repeat 2) until an azimuth of 337° is reached. 4) Repeat 1) to 3) for the other orthogonal antenna polarization. 5) Move the antenna and the turntable to the position where the maximum value is detected. 6) Measure while moving the antenna slowly +/- 1 m 7) Set the antenna to the position where the maximum value is found 8) Measure while moving the turntable +/- 45° 9) Set the turntable to the azimuth where the maximum value is found 10) Measure with Final detector (QP or AV) and note the value 11) Repeat 5) to 10) for each frequency 12) Repeat 1) to 11) for each orthogonal axes of the EUT Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 10 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Final measurement (1 GHz to 26 GHz) This measurement will be performed in a fully anechoic chamber with a measuring distance of 3 meter. Tabletop devices will set up on a non-conducting support with a size of 1 m by 1.5 m and a height of 80 cm. Floor-standing devices will be placed directly on the turntable/ground plane. The set up of the Equipment under test will be in accordance to ANSI C63.4-1992 [1]. The frequency range will be divided into different sub ranges depending of the frequency range of the used horn antenna. The EMI Receiver set to MAX Hold mode and a resolution bandwidth of 1 MHz. The measurement will be performed in horizontal and vertical polarisation of the measuring antenna and while rotating the EUT in its vertical axis in the range of 0 ° to 360 °. If the EUT is larger than the antenna beamwidth, the antenna will be moved to various positions, to cover the whole surface of the EUT. It might be possible to shorter the measuring distance to higher the measurement sensitivity. The resolution bandwidth of the EMI Receiver will be set to the following values: Frequency range Resolution bandwidth 1 GHz to 26 GHz 1 MHz Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 11 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 measuring distance preamp EUT antenna hight 0,8 m EMI receiver Procedure of measurement: The measurements were performed in the frequency range 1 GHz to 26 GHz. The following procedure will be used: 1) Monitor the frequency range at horizontal polarisation and a EUT azimuth of 0 °. 2) Rotate the EUT by 360 ° to maximize the detected signals. 3) Change the antenna polarisation. 4) Rotate the EUT by 360 ° to maximize the detected signals. 5) Make a hardcopy of the spectrum. 6) Measure the frequency of the detected emissions with a lower span and resolution bandwidth to increase the accuracy and note the frequency value. 7) Measure the level of the detected frequency with the correct resolution bandwidth, with the antenna polarisation and azimuth and the peak and average detector, which causes the maximum emission. 8) Repeat steps 1) to 7) with the other orthogonal axes of the EUT if handheld equipment. 9) Repeat steps 1) to 8) for the next antenna spot if the EUT is larger than the antenna beamwidth. Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 12 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 4.2 FREQUENCY STABILITY WITH RESPECT TO AMBIENT TEMPERATURE AND SUPPLY VOLTAGE Climatic chamber EUT 0.2 m 0.3 m Power Spectrum supply analyser The following procedure will be used: 1) Place the EUT in the climatic chamber 2) Switch on the EUT and check the correct function and the settings of the spectrum analyser 3) Switch off the EUT and tune the climatic chamber to a temperature of 20 °C. Wait until the thermal balance is obtained 4) Switch the EUT on and record the frequency at start-up and 2, 5 and 10 minutes after powering on. 5) Repeat 4) with 85 % and 115 % of the nominal supply voltage (AC only) 6) Switch off the EUT and tune the climatic chamber to a temperature of 50 °C. Wait until the thermal balance is obtained 7) Switch the EUT on and record the frequencies at start-up and 2, 5 and 10 minutes after powering on. 8) Repeat 7) with 85 % and 115 % of the nominal supply voltage (AC only) 9) Switch off the EUT and tune the climatic chamber to a temperature of -20 °C. Wait until the thermal balance is obtained 10) Switch the EUT on and record the frequencies at start-up and 2, 5 and 10 minutes after powering on. 11) Repeat 10) with 85 % and 115 % of the nominal supply voltage (AC only) Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 13 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 4.2.1 POWER OUTPUT CONDUCTED Ambient temperature 20 °C Relative humidity 55 % Test record: The test was carried out in transmit mode of the EUT. All results are shown in the following. Supply voltage: During all measurements the EUT was supplied with 6 V DC. A coaxial cable was connected to the rf-output of the transmitter instead of the integral antenna. The output power was measured without modulation. Power measurement (conducted): Channel: Frequency: Analyser Cable loss: Output power: reading: 1 2458 MHz +25.4 dBm 1.0 dB +26.4 dBm 2 2474 MHz +25.3 dBm 1.0 dB +26.3 dBm Calculation: Output power = Analyser reading + Cable loss TEST EQUIPMENT USED FOR THE TEST: 31, 54, 55 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 14 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 15 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 4.2.2 POWER OUTPUT RADIATED Ambient temperature 20 °C Relative humidity 55 % Position of EUT: The EUT was set-up on a wooden table of a height of 0.8 m. The distance between EUT and antenna was 3 m. Cable guide: No cable run necessary. Test record: The test was carried out in transmit mode of the EUT. All results are shown in the following. Supply voltage: During the measurements the EUT was supplied with the integral rechargeable battery. Power measurement (radiated): 30764Ch1_3.wmf: 1 GHz to 4 GHz, transmit, channel 1 Marker 1 [T1] RBW 1 MHz RF Att 0 dB Ref Lvl 87.63 dBµV VBW 1 MHz 90 dBµV 2.45800000 GHz SWT 7.5 ms Unit dBµV 90 1 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 1 GHz 300 MHz/ Stop 4 GHz Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 16 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 30764Ch2_3.wmf: 1 GHz to 4 GHz, , transmit, channel 2 Marker 1 [T1] RBW 1 MHz RF Att 10 dB Ref Lvl 87.97 dBµV VBW 1 MHz 90 dBµV 2.47400000 GHz SWT 7.5 ms Unit dBµV 90 1 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 1 GHz 300 MHz/ Stop 4 GHz Measurement results: Channel: Frequency: Analyser Cable loss: Antenna Field reading: factor: strength: MHz dBµV dB dB/m dBµV/m 1 2458 MHz 87.63 4.15 29.3 121.1 2 2474 MHz 87.97 4.35 28.7 121.0 Calculation: Field strength = Analyser reading + Cable loss + Antenna factor TEST EQUIPMENT USED FOR THE TEST: 29, 31-34, 36, 43, 44, 54 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 17 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 4.2.3 SPURIOUS EMISSIONS RADIATED Ambient temperature 20 °C Relative humidity 55 % Position of EUT: The EUT was set-up on a wooden table of a height of 0.8 m. The distance between EUT and antenna was 3 m. Cable guide: No cable run necessary. Test record: The test was carried out in transmit mode of the EUT. All results are shown in the following. Supply voltage: During the measurements the EUT was supplied with the integral rechargeable battery. Measurement results (radiated): Channel 1: RBW 100 kHz RF Att 0 dB Ref Lvl VBW 100 kHz 90 dBµV SWT 43 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 30 MHz 17 MHz/ Stop 200 MHz 30764Ch1_1.wmf: 30 MHz to 200 MHz, transmit, channel 1 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 18 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 RBW 100 kHz RF Att 0 dB Ref Lvl VBW 100 kHz 90 dBµV SWT 200 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 200 MHz 80 MHz/ Stop 1 GHz 30764Ch1_2.wmf: 200 MHz to 1000 MHz, transmit, channel 1 Marker 1 [T1] RBW 1 MHz RF Att 0 dB Ref Lvl 87.63 dBµV VBW 1 MHz 90 dBµV 2.45800000 GHz SWT 7.5 ms Unit dBµV 90 1 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 1 GHz 300 MHz/ Stop 4 GHz 30764Ch1_3.wmf: 1 GHz to 4 GHz, transmit mode, channel 1 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 19 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Marker 1 [T1] RBW 1 MHz RF Att 0 dB Ref Lvl 26.20 dBµV VBW 1 MHz 90 dBµV 4.00000000 GHz SWT 80 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 1 20 10 0 -10 Start 4 GHz 800 MHz/ Stop 12 GHz 30764Ch1_4.wmf: 4 GHz to 12 GHz, transmit, channel 1 RBW 1 MHz RF Att 0 dB Ref Lvl VBW 1 MHz 90 dBµV SWT 60 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 12 GHz 600 MHz/ Stop 18 GHz 30764Ch1_5.wmf: 12 GHz to 18 GHz, transmit, channel 1 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 20 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 RBW 1 MHz RF Att 0 dB Ref Lvl VBW 1 MHz 90 dBµV SWT 80 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 18 GHz 800 MHz/ Stop 26 GHz 30764Ch1_6.wmf: 18 GHz to 26 GHz, transmit, channel 1 Limit of the spurious emission: Limit = 43 + 10 x log P, P (conducted) = 26.4 dBm = 437 mW Limit = 39.4 dBc Frequency: Spectrum Signal Cable Antenna Corrected Limit: Margin: Result: analyser Generator loss: gain: Generator level: level: level MHz dBµV dBm dB dB dBc dBc dB 649.995 24.5 -54 0.5 6.4 74.6 39.4 35.2 Passed No other spurious emission found. Continued next page: Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 21 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Channel 2: RBW 100 kHz RF Att 0 dB Ref Lvl VBW 100 kHz 90 dBµV SWT 43 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 30 MHz 17 MHz/ Stop 200 MHz 30764Ch2_1.wmf: 30 MHz to 200 MHz, transmit, channel 2 RBW 100 kHz RF Att 0 dB Ref Lvl VBW 100 kHz 90 dBµV SWT 200 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 200 MHz 80 MHz/ Stop 1 GHz 30764Ch2_2.wmf: 200 MHz to 1000 MHz, transmit, channel 2 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 22 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Marker 1 [T1] RBW 1 MHz RF Att 10 dB Ref Lvl 87.97 dBµV VBW 1 MHz 90 dBµV 2.47400000 GHz SWT 7.5 ms Unit dBµV 90 1 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 1 GHz 300 MHz/ Stop 4 GHz 30764Ch2_3.wmf: 1 GHz to 4 GHz, transmit, channel 2 Marker 1 [T1] RBW 1 MHz RF Att 0 dB Ref Lvl 27.20 dBµV VBW 1 MHz 90 dBµV 4.00000000 GHz SWT 80 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 301 PRN 20 10 0 -10 Start 4 GHz 800 MHz/ Stop 12 GHz 30764Ch2_4.wmf: 4 GHz to 12 GHz, transmit, channel 2 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 23 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 RBW 1 MHz RF Att 0 dB Ref Lvl VBW 1 MHz 90 dBµV SWT 60 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 12 GHz 600 MHz/ Stop 18 GHz 30764Ch2_5.wmf: 12 GHz to 18 GHz, transmit, channel 2 RBW 1 MHz RF Att 0 dB Ref Lvl VBW 1 MHz 90 dBµV SWT 80 ms Unit dBµV 90 A 80 70 60 IN1 1MAX 1MA 50 40 30 20 10 0 -10 Start 18 GHz 800 MHz/ Stop 26 GHz 30764Ch2_6.wmf: 18 GHz to 26 GHz, transmit, channel 2 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 24 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Limit of the spurious emission: Limit = 43 + 10 x log P, P (conducted) = 26.3 dBm = 427 mW Limit = 39.3 dBc Frequency: Spectrum Signal Cable Antenna Corrected Limit: Margin: Result: analyser Generator loss: gain: Generator level: level: level MHz dBµV dBm dB dB dBc dBc dB 649.995 24.5 -54 0.5 6.4 74.6 39.3 35.3 Passed No other spurious emission found Test: Passed TEST EQUIPMENT USED FOR THE TEST: 29, 31-34, 36, 43, 44, 54 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 25 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 4.3 FREQUENCY STABILITY / VOLTAGE VARIATION Ambient temperature 20 °C Relative humidity 50 % Test record: The test was carried out in normal operation mode (without modulation). All results are shown in the following. Measuring results: Channel 1 Temperature: Voltage: Measured Relative error: frequency: 6.8 V DC 2458.000125 MHz +0.020 ppm +20° C 7.0 V DC 2458.000129 MHz +0.021 ppm 7.2 V DC 2458.000120 MHz +0.017 ppm 7.4 V DC 2458.000120 MHz +0.017 ppm 7.6 V DC 2458.000078 MHz Reference 7.8 V DC 2458.000082 MHz +0.002 ppm 8.0 V DC 2458.000085 MHz +0.003 ppm 8.2 V DC 2457.000087 MHz +0.004 ppm 8.4 V DC 2457.000085 MHz +0.003 ppm Measuring results: Channel 2 Temperature: Voltage: Measured Relative error: frequency: 6.8 V DC 2474.000129 MHz +0.017 ppm +20° C 7.0 V DC 2474.000128 MHz +0.026 ppm 7.2 V DC 2474.000125 MHz +0.015 ppm 7.4 V DC 2474.000118 MHz +0.013 ppm 7.6 V DC 2474.000086 MHz Reference 7.8 V DC 2474.000081 MHz -0.002 ppm 8.0 V DC 2474.000080 MHz -0.002 ppm 8.2 V DC 2474.000078 MHz -0.003 ppm 8.4 V DC 2474.000075 MHz -0.004 ppm TEST EQUIPMENT USED FOR THE TEST: 31, 54, 55, 56, 57 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 26 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 4.4 FREQUENCY STABILITY / TEMPERATURE VARIATION Ambient temperature 20 °C Relative humidity 50 % Test record: The test was carried out in normal operation mode (without modulation). All results are shown in the following. Measuring results: Channel 1 Temperature: Voltage: Measured Relative error: frequency: +20° C 2458.000 MHz Reference -30° C 2458.595 MHz +242 ppm -20° C 2458.585 MHz +237 ppm -10° C 7.6 V DC 2458.125 MHz +50 ppm 0° C 2458.013 MHz +5.3 ppm +10° C 2458.002 MHz +0.8 ppm +20° C 2458.000 MHz +0.0 ppm +30° C 2457.998 MHz -0.2 ppm +40° C 2457.995 MHz -0.4 ppm +50° C 2457.990 MHz -0.6 ppm Measuring results: Channel 2 Temperature: Voltage: Measured Relative error: frequency: +20° C 2474.000 MHz Reference -30° C 2474.706 MHz +285 ppm -20° C 2474.655 MHz +264 ppm -10° C 7.6 V DC 2474.165 MHz +66 ppm 0° C 2474.075 MHz +30 ppm +10° C 2474.002 MHz +0.8 ppm +20° C 2474.000 MHz +0.0 ppm +30° C 2473.997 MHz -0.3 ppm +40° C 2473.995 MHz -0.4 ppm +50° C 2473.990 MHz -0.6 ppm TEST EQUIPMENT USED FOR THE TEST: 31, 54, 55, 56, 57 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 27 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 4.5 OCCUPIED BANDWIDTH Ambient temperature 20 °C Relative humidity 50 % Test record: The test was carried out in normal operation mode (modulated with NTSC-colour bar). All results are shown in the following. Measuring results: RBW 300 kHz RF Att 0 dB Ref Lvl VBW 300 kHz -10 dBm SWT 5 ms Unit dBm -10 A -20 -30 -40 IN1 1MAX 1MA -50 -60 VTQ-Part -70 -80 -90 -100 -110 Center 2.458 GHz 10 MHz/ Span 100 MHz 30764FCC_OBW.wmf: Occupied bandwidth Calculation: Max modulation M: M = 4.25 MHz (525 lines NTSC video according CCIR 405) Max. deviation D: D = 4 MHz Bandwidth B: B = 2 x ( M + D ) = 16.5 MHz Emission designator: 16M5F3E Measurement: 99.75 % (Occupied Bandwidth) Bandwidth: B = 13.1 MHz Band designator: 13M1F3E Test: Passed TEST EQUIPMENT USED FOR THE TEST: 31, 54, 55, 57 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 28 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 5 TEST EQUIPMENT AND ANCILLARIES USED FOR TESTS Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 29 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Emission measurement at AC mains and DC in / out ports at M4 No. Test equipment Type Manufacturer Serial No. PM-No 1 Shielded chamber M4 - Siemens B83117S1-X158 480088 2 Measuring receiver ESAI Rohde & Schwarz 831953/001 480025 833181/018 480026 3 LISN NSLK8128 Schwarzbeck 8128155 480058 4 DC-filter B84266-A21- Siemens 940164525 480099 E13 5 AC-filter B84299-D87- Siemens 930262292 480097 E3 6 EMI-Software ES-K1 Rohde & Schwarz - 480111 Radiated emission measurement at M5 No. Test equipment Type Manufacturer Serial No. PM-No 7 Fully anechoic chamber M5 - Siemens B83177-S1-X156 480073 8 Measuring receiver ESVS30 Rohde & Schwarz 829673/012 480024 9 Controller HD100 Deisel 100/324 480067 10 Antenna support MA240 Deisel 228/314 480069 11 Turntable DS412 Deisel 412/317 480070 12 Antenna CBL6112C Chase 2689 480327 13 EMI Software ES-K1 Rohde & Schwarz - 480111 Radiated emission measurement at M6 No. Test equipment Type Manufacturer Serial No. PM-No 14 Open area test site - Phoenix Test-Lab - 480085 15 Measuring receiver ESVS30 Rohde & Schwarz 829673/012 480024 16 Controller HD100 Deisel 100/670 480139 17 Turntable DS420HE Deisel 420/620/80 480087 18 Antenna support AS615P Deisel 615/310 480086 19 Antenna CBL6111 A Chase 1643 480147 20 EMI Software ES-K1 Rohde & Schwarz - 480111 Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 30 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 Radiated emission measurement at M8 No. Test equipment Type Manufacturer Serial No. PM-No 21 Fully anechoic chamber M8 - Siemens B83117-E7019- 480190 T231 22 Measuring receiver ESMI Rohde & Schwarz 843977/001 480179 843530/018 480180 23 Measuring receiver ESCS 30 Rohde & Schwarz 828985/014 480270 24 Controller HD100 Deisel 100/427 480181 25 Turntable DS420 Deisel 420/435/97 480186 26 Antenna support AS615P Deisel 615/310 480187 27 Antenna CBL6112 A Chase 2034 480185 28 EMI Software ES-K1 Rohde & Schwarz - 480111 Radiated emission measurement at M20 No. Test equipment Type Manufacturer Serial No. PM-No 29 Fully anechoic chamber M20 - Albatross Projects B83107-E2439- 480303 T232 30 Measuring receiver ESMI Rohde & Schwarz 843977/001 480179 843530/018 480180 31 Measuring receiver ESI 40 Rohde & Schwarz 100064 480355 32 Controller HD100 Deisel 100/670 480326 33 Turntable DS420HE Deisel 420/620/80 480315 34 Antenna support AS615P Deisel 615/310 480187 35 Antenna CBL6112 B Chase 2688 480328 36 Antenna 3115 A EMCO 9609-4918 480183 37 Standard Gain Horn 18240-20 Flann Microwave 483 480294 11.9GHz –18GHZ 38 Standard Gain Horn 18240-20 Flann Microwave 482 480295 11.9GHz –18GHZ 39 Standard Gain Horn 20240-20 Flann Microwave 411 480297 17.9GHz –26.7GHZ 40 Standard Gain Horn 20240-20 Flann Microwave 410 480296 17.9GHz –26.7GHZ 41 Standard Gain Horn 22240-20 Flann Microwave 469 480299 26.4GHz –40.1GHZ Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 31 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 No. Test equipment Type Manufacturer Serial No. PM-No 42 Standard Gain Horn 22240-20 Flann Microwave 468 480298 26.4GHz –40.1GHZ 43 RF-cable No. 30 RTK 081 Rosenberger - 410141 44 RF-cable No. 31 RTK 081 Rosenberger - 410142 45 RF-cable 1m KPS-1533- Insulated Wire - 480300 400-KPS 46 RF-cable 1m KPS-1533- Insulated Wire - 480301 400-KPS 47 RF-cable 2m KPS-1533- Insulated Wire - 480302 400-KPS 48 RF-cable No. 5 RTK 081 Rosenberger 410097 49 Preamplifier JS3- Miteq 681851 480337 00101200- 23-5A 50 Preamplifier JS3- Miteq 571667 480343 12001800- 16-5A 51 Preamplifier JS3- Miteq 658697 480342 18002600- 20-5A 52 Preamplifier JS3- Miteq 563593 480344 26004000- 25-5A 53 EMI Software ES-K1 Rohde & Schwarz - 480111 Ancillary equipment used for testing No. Test equipment Type Manufacturer Serial No. PM-No 54 Power supply TOE 8752 Toellner 31566 480010 55 RF-cable No. 5 RTK 081 Rosenberger - 410097 56 Climatic chamber GTS500.40 GTS 1660 490073 57 Test fixture - Phoenix Test-Lab - 410160 All used measurement equipment was calibrated (if necessary). The calibration intervals and the calibration history will be given out on request. Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 32 of 33

TEST REPORT REFERENCE: R30764 TX Edition 3 6 LIST OF ANNEXES ANNEX A INTERNAL PHOTOGRAPHS OF THE TEST SAMPLE: 3 pages EUT (transmitter) internal view 30445tx01.jpg PCB (transmitter) top view 30445tx03.jpg PCB (transmitter) rear view 30445tx04.jpg ANNEX B EXTERNAL PHOTOGRAPHS OF THE TEST SAMPLE: 3 pages EUT (transmitter) front view 30445tx1.jpg EUT (transmitter) rear view 30445tx2.jpg EUT (transmitter) external power supply 30445tx4.jpg ANNEX C PHOTOGRAPHS OF THE TEST SET-UP: 2 pages Test set-up radiated emission (anechoic chamber) 30445emi_tx.jpg Test set-up radiated emission (open area test-site) 30445emi_tx_ff2.jpg Examiner: Raimund BLASK Date of issue: 2 December 2003 Page 33 of 33


Document Created: 2004-01-22 14:13:20
Document Modified: 2004-01-22 14:13:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC