Modular Approval Letter

FCC ID: RI7UC864G

Cover Letter(s)

Download: PDF

FCCID_1246523

Applicant/Grantee Telit Communications S.p.A.
FCC ID: RI7UC864G
IC ID: 5131A-UC864G
Section 15.212 Modular Transmitters
Request for Modular Approval Request for Limited Modular Approval
Requirements EUT Conditions Comply (Y/N)
Single Modular Approval Requirements
1 The radio elements of the modular The radio elements are fully shielded to Y
transmitter must have their own prevent interference between the
shielding. The physical crystal and crystal/tuning capacitor and the radio
tuning capacitors may be located elements.
external to the shielded radio elements.
2 The modular transmitter must have The modular transmitter has buffered Y
buffered modulation/data inputs (if such modulation/data inputs.
inputs are provided) to ensure that the
module will comply with Part 15
requirements under conditions of
excessive data rates or over-modulation.
3 The modular transmitter must have its The module has its own power supply Y
own power supply regulation. regulation through the PMIC chip.
4 The modular transmitter must comply The module has unique antenna Y
with the antenna and transmission connectors. Antenna gain information is
system requirements of Sections 15.203, listed in the Antenna spec.
15.204(b) and 15.204(c). The antenna
must either be permanently attached or
employ a “unique” antenna coupler (at
all connections between the module and
the antenna, including the cable). The
“professional installation” provision of
Section 15.203 is not applicable to
modules but can apply to limited
modular approvals under paragraph (b)
of this section.
5 The modular transmitter must be tested All tests reported in this application were Y
in a stand-alone configuration, i.e., the performed on a stand-alone basis.
module must not be inside another
device during testing for compliance
with Part 15 requirements. Unless the
transmitter module will be battery
powered, it must comply with the AC
line conducted requirements found in
Section 15.207. AC or DC power lines
and data input/output lines connected to
the module must not contain ferrites,
unless they will be marketed with the
module (see Section 15.27(a)). The
length of these lines shall be the length
typical of actual use or, if that length is
unknown, at least 10 centimeters to
insure that there is no coupling between

the case of the module and supporting
equipment. Any accessories, peripherals,
or support equipment connected to the
module during testing shall be
unmodified and commercially available
(see Section 15.31(i)).
6 The modular transmitter must be Please refer to the FCC ID information Y
equipped with either a permanently in Label Info.
affixed label or must be capable of
electronically displaying its FCC
identification number.
(A) If using a permanently affixed label, the
modular transmitter must be labeled with its own
FCC identification number, and, if the FCC
identification number is not visible when the
module is installed inside another device, then
the outside of the device into which the module is
installed must also display a label referring to
the enclosed module. This exterior label can use
wording such as the following: “Contains
Transmitter Module
FCC ID: XYZMODEL1” or “Contains FCC ID:
XYZMODEL1.” Any similar wording
that expresses the same meaning may be used.
The Grantee may either provide such a label, an
example of which must be included in the
application for equipment
authorization, or, must provide adequate
instructions along with the module which explain
this requirement. In the latter case, a copy of
these instructions must be included in the
application for equipment authorization.
(B) If the modular transmitter uses an electronic
display of the FCC identification number, the
information must be readily accessible and
visible on the modular transmitter or on the
device in which it is installed. If the module is
installed inside another device, then the outside
of the device into which the module is installed
must display a label referring to the enclosed
module. This exterior label can use wording such
as the following:
“Contains FCC certified transmitter module(s).”
Any similar wording that expresses the same
meaning may be used. The user manual must
include instructions on how to access the
electronic display. A copy of these instructions
must be included in the application for
equipment authorization.
7 The modular transmitter must comply This module complies with all of Y
with any specific rules or operating relevant FCC requirements and the
requirements that adequate instructions to keep the
ordinarily apply to a complete compliance have been provided in the
transmitter and the manufacturer must User’s Guide.
provide adequate instructions along with
the module to explain any such
requirements. A copy of these
instructions must be included in the

application for equipment authorization.
8 The modular transmitter must comply This module will be used only for Y
with any applicable RF exposure mobile and fixed application. The
requirements in its final configuration. antenna(s) used for this transmitter will
be installed to provide a separation
distance of at least 20 cm from all
persons and will not be co-located or
operating in conjunction with any other
antenna or transmitter. See the MPE
report.
A limited modular approval may be granted for single or split modular transmitters that do not comply with
all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or
power supply regulation, if the manufacturer can demonstrate by alternative means in the application for
equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the
operating conditions in which the transmitter will be used. Limited modular approval also may be granted in
those instances where compliance with RF exposure rules is demonstrated only for particular product
configurations. The applicant for certification must state how control of the end product into which the module
will be installed will be maintained such that full compliance of the end product is always ensured.

Document Created: 2010-02-11 17:50:49
Document Modified: 2010-02-11 17:50:49

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC