RF Exposure Information

FCC ID: RI7GE864

RF Exposure Info

Download: PDF
FCCID_680630

Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention: Reviewing Engineer RE: RF exposure information for the equipment GE864-QUAD and GE864-PY (FCC ID: RI7GE864) RF exposure information The device RI7GE864 is designed as module to be installed in other devices. This device is to be used only for fixed and mobile applications. If the final product after integration is intended for portable use, a new application and FCC is required. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all the persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The table below is excerpted from Table 1B of 47 CFR 1.1310 titled Limits for Maximum Permissible Exposure (MPE), Limits for General Population/Uncontrolled Exposure: The equipment RI7GE864 transmits in the following frequency ranges so that the applicable limits are: Frequency range Limit 2 1850.2 - 1909.8 MHz 1 mW/cm 2 824.2 - 848.8 MHz 0.54 mW/cm The equipment is a GPRS Class 10, so the maximum duty cicle is 2/8 = 1/4 Under conditions stated above MPE limits can be guaranteed as the calculation below shows: 850 MHz frequency band Maximum conducted output power: 2.06 W Duty cicle: 1/4 Equivalente conducted output power = Maximum conducted output power x Duty cicle = 2.06 W x 1/4 = 0.515 W = 515 mW Maximum antenna gain (as stated in the User’s guide) = 3 dBi (numerical gain) Using the eqution: 2 S = P·G/4·pi·R Where, 2 S = power density in mW/cm P = power input to the antenna in mW G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the centre of radiation of the antenna in cm (20 cm Prediction distance) 2 2 2 S = 515 mW·2 / 4·pi·(20 cm) = 0.21 mW/cm < 0.54 mW/cm (limit)

1900 MHz frequency band Maximum conducted output power: 0.90 W Duty cicle: 1/4 Equivalente conducted output power = Maximum conducted output power x Duty cicle = 0.90 W x 1/4 = 0.225 W = 225 mW Maximum antenna gain (as stated in the User’s guide) = 3 dBi (numerical gain) Using the eqution: 2 S = P·G/4·pi·R Where, 2 S = power density in mW/cm P = power input to the antenna in mW G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the centre of radiation of the antenna in cm (20 cm Prediction distance) 2 2 2 S = 225 mW·2 / 4·pi·(20 cm) = 0.089 mW/cm < 1 mW/cm (limit) These predictions demonstrate that: The power density levels at a distance of 20 cm with typical antennas of a gain of less than 3 dBi are below the maximum levels allowed by the FCC rules. Conclusion: The equipment RI7GE864 complies with the MPE limits if used with antennas with a gain of less than 3 dBi and this antenna is installed to provide a separation distance of at least 20 cm from all the persons. Warning: To ensure the compliance with the MPE limits the antenna gain has been limited in page 18 of the user’s guide and a warning statement has been included in page 57. Signed on behalf of Telit Communications S.p.A. by P.A. Mr. Sandro Spanghero Technical Director Telit Communications S.p.A. Viale Stazione di Prosecco 5/B, I-34010 Trieste, Italy Phone: +39 040 4192111 E-mail: sandro.spanghero@telit.net Date: 2006-06-30


Document Created: 2006-06-30 19:10:44
Document Modified: 2006-06-30 19:10:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC