18_CTR35 RFExp Teil 2 von 2

FCC ID: RFD-CTR35

RF Exposure Info

Download: PDF
FCCID_2997905

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Eurofins Certificate No: DAE3—522_Sep15 |CALIBRATION CERTIFICATE | Object DAE3 — SD 000 D03 AA — SN: 522 Calibration procedure(s) QA CAL—06.v29 Calibration procedure for the data acquisition electronics (DAE) Calibration date: September 24, 2015 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Keithley Multimeter Type 2001 SN: 0810278 09—Sep—15 (No:17153) Sep—16 Secondary Standards ID # Check Date (in house) Scheduled Check Auto DAE Calibration Unit SE UWS 053 AA 1001 O6—Jan—15 (in house check) In house check: Jan—16 Calibrator Box V2.1 SE UMS 006 AA 1002 O6—Jan—15 (in house check) In house check: Jan—16 Name Function Signature Calibrated by: Eric Hainfeld Technician y — = Approved by: Fin Bomholt Deputy Technical Manager + \) ’g Lu p wV . f LU/\/ Issued: September 24, 2015 This calibration certificate shall not be reproduced except in full without written approvalof the laboratory. Certificate No: DAE3—522_Sep15 Page 1 of 5 mg— c en >

Calibration A Laboratory of wl 97 S/Z Schweizerischer Kalibrierdienst Schmid & Partner ilf:\\_4'53: Service suisse d‘étalonnage Engineering AG Lm Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland "4,///\\\\\\‘\ Swiss Calibration Service rhitabs Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters e DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. e Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. e The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. e DC Voltage Measurement Linearity: Verification of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. e Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. e Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. e AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage e Input Offset Measurement. Output voltage and statistical results over a large number of zero voltage measurements. e Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. e Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. e Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. + Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE3—522_Sep15 Page 2 of 5

DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1LSB= 6.AuV , full range = —100...+300 mV Low Range: 1LSB= 61nV , full ranges 1....... +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y Z High Range 404.198 + 0.02% (k=2) 403.863 £ 0.02%(k=2) 404.698 £ 0.02% (k=2) Low Range 3.96451 + 1.50% (k=2) 3.95745 £1.50% (k=2) 8.97398 £ 1.50% (k=2) Connector Angle Connector Angle to be used in DASY system 56.0 °+1 ° Certificate No: DAE3—522_Sep15 Page 3 of 5 mg— n c >

Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltage Linearity High Range Reading (uV) Difference (1uV) Error (%) Channel X + Input 200037.86 0.08 0.00 Channel X + Input 20006.75 247 0.01 Channel X — Input 2000115 4.82 0.02 Channel Y + Input 200036.95 —0.67 —0.00 Channel Y + Input 20005.40 0.94 0.00 Channel Y — Input —20001.70 4.95 —0.02 Channel Z + Input 200038.78 0.88 0.00 Channel Z + Input 20003.12 ~1.20 —0.01 Channel Z2 — Input 2000489 1.37 —0.01 Low Range Reading (V) Difference (1uV) Error (%) Channel X + Input 2000.75 0.01 0.00 Channel X + Input 200.67 9.11 —0.05 Channel X — Input —198.63 0.60 —0.30 Channel Y + Input 2000.71 0.04 0.00 Channel Y + Input 199.25 ~1.30 —0.65 Channel Y — Input —200.06 —0.69 0.35 Channel Z + Input 2000.53 —0.08 —0.00 Channel Z + Input 199.47 —1.09 —0.54 Channel Z — Input 200.51 ~1.14 0.57 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (uV) Average Reading (uV) Channel X 200 —3.92 5.97 —200 6.71 5.09 Channel Y 200 —0.54 —0.66 —200 —0.21 —0.52 Channel Z 200 16.77 15.63 —200 —17.68 —18.50 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input Voltage (mV) Channel X (uV) Channel Y (uV) Channel Z (uV) Channel X 200 — —2.21 —2.23 Channel Y 200 8.59 — —0.90 Channel Z 200 5.35 5.42 — Certificate No: DAE3—522_Sep15 Page 4 of 5 w

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 15743 17021 Channel Y 15716 14963 Channel Z 16065 17384 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MQ Average (1V) min. Offset (uV) max. Offset (uV) Sid: ?:‘)l;ation Channel X 0.97 —0.75 2.41 0.58 Channel Y 0.24 ~1.21 1.47 0.58 Channel Z 0.16 ~1.04 1.85 0.56 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channel X 200 200 Channel Y 200 200 Channel Z 200 200 Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vec) +7.9 Supply (— Vee) —7.6 9. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ Vee) +0.01 +6 +14 Supply (— Vec) —0.01 —8 9 Certificate No: DAE3—522_Sep15 Page 5 of 5

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Eurofins Certificate No: D2450V2—722_Sep15 [CALIBRATION CERTIFICATE Object D2450V2 — SN: 722 Calibration procedure(s) QA CAL—05.v9 Calibration procedure for dipole validation kits above 700 MHz Calibration date: September 28, 2015 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 07—Oct—14 (No. 217—02020) Oct—15 Power sensor HP 8481A US37292783 07—Oct—14 (No. 217—02020) Oct—15 Power sensor HP 8481A MY41092317 07—Oct—14 (No. 217—02021) Oct—15 Reference 20 dB Attenuator SN: 5058 (20k) O01—Apr—15 (No. 217—02131) Mar—16 Type—N mismatch combination SN: 5047.2 / 06327 01—Apr—15 (No. 217—02134) Mar—16 Reference Probe EXSDV4 SN: 7349 30—Dec—14 (No. EX3—7349_Dec14) Dec—15 DAE4 SN: 601 17—Aug—15 (No. DAE4—601_Aug15) Aug—16 Secondary Standards ID # Check Date (in house) Scheduled Check RF generator R&S SMT—06 100972 15—Jun—15 (in house check Jun—15) In house check: Jun—18 Network Analyzer HP 8753E US37390585 $4206 18—Oct—01 (in house check Oct—14) In house check: Oct—15 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technician ( &/’ ce tgm.. —L. Approved by: KatJa Pokovic Technical Manager as Issued: September 28, 2015 This calibration certificate shall not be reproduced except in full without written approvalof the laboratory. Certificate No: D2450V2—722_Sep15 Page 1 of 8 mge— c— oo >

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—722_Sep15 Page 2 of 8 ruge y n ve c >

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.8.8 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 £0.2) °C 39.2 +6 % 1.86 mho/m + 6 % Head TSL temperature change during test <0.5 °C «s«% sute SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 12.7 Wikg SAR for nominal Head TSL parameters normalized to 1W 50.0 W/kg + 17.0 %(k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 5.90 W/kg SAR for nominal Head TSL parameters normalized to 1W 23.4 Wikg x 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 £0.2) °C 53.2 +6 % 2.00 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 12.5 W/kg SAR for nominal Body TSL parameters normalized to 1W 49.5 Wikg * 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 5.88 W/kg SAR for nominal Body TSL parameters normalized to 1W 23.4 Wikg + 16.5 % (k=2) Certificate No: D2450V2—722_Sep15 Page 3 of 8 Iugy ve vely

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 51.7 Q + 9.2 jQ Return Loss ~20.8 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 46.3 Q + 8.6 jQ Return Loss —20.2 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.152 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on October 16, 2002 Certificate No: D2450V2—722_Sep15 Page 4 of 8 ruge ve veke

DASY5 Validation Report for Head TSL Date: 28.09.2015 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz ; Type: D2450V2; Serial: D2450V2 — SN: 722 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.86 S/m; &, = 39.2; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.67, 7.67, 7.67); Calibrated: 30.12.2014; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 17.08.2015 & Phantom: Flat Phantom 5.0 (front); Type: QDOOOP5OAA; Serial: 1001 * DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 111.4 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 26.1 W/kg SAR(1 g) = 12.7 W/kg; SAR(10 g) = 5.9 W/kg Maximum value of SAR (measured) =21.1 W/kg ~4.00 —8.00 —12.00 —16.00 —20.00 0 dB = 21.1 W/kg = 13.24 dBW/kg Certificate No: D2450V2—722_Sep15 Page 5 of 8 Pauge vivile

Impedance Measurement Plot for Head TSL 28 Sep 2015 12:29:139 (CHI] sii 1 U FS 4i 51.721 8 .1563 a 594.80 pH 2 450.000 000 MHz De 1 Ca fAVg 16 HLd CH2 Ca Av 16° H1d START 2 250.000 000 MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—722_Sep15 Page 6 of 8 | uge vevere

DASY5 Validation Report for Body TSL Date: 28.09.2015 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz ; Type: D2450V2; Serial: D2450V2 — SN: 722 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 2 S/m; &, = 53.2; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.53, 7.53, 7.53); Calibrated: 30.12.2014; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 17.08.2015 e Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 e DASY32 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 105.8 V/m; Power Drift =—0.01 dB Peak SAR (extrapolated) = 24.7 W/kg SAR(I g) = 12.5 W/kg; SAR(10 g) = 5.88 W/kg Maximum value of SAR (measured) = 20.5 W/kg ~4.00 —8.00 —12.00 +16.00 —20.00 0 dB = 20.5 W/kg = 13.12 dBW/kg Certificate No: D2450V2—722_Sep15 Page 7 of 8 mg— c— oo >

Impedance Measurement Plot for Body TSL 28 Sep 2015 12:29:11 CHI) sii 1 U OFS 4:146.293 n ©.6325 a 560.90 pH 2450.000 000 MHz : canieazzgeans Del Ca fvgq 16 H1d CH2 Ca Ay 36° H1d START 2 250.000 000 MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—722_Sep15 Page 8 of 8

ANNEX B System Validation Reports Test Report No.: G0M-1601-5313-TFC093SR-V02 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 71 of 75

Date/Time: 3/22/2016 7:54:05 AM Test Laboratory: Eurofins Product Service GmbH System Performance Check - SAM Phantom - EX3DV6 - MSL - 2450 MHz 22_03_2016 DUT: Dipole 2450 MHz; Type: D2450V2; Serial: 722 Communication System: UID 0 - n/a, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: Muscle 2450 MHz Medium parameters used (interpolated): f = 2450 MHz; σ = 2.005 S/m; εr = 50.474; ρ = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY5.2 Configuration: Probe: EX3DV4 - SN3893 (add ConvF); ConvF(7.6, 7.6, 7.6); Calibrated: 10/22/2015; Sensor-Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE3 Sn522; Calibrated: 9/24/2015 Phantom: SAM 12; Type: TP-1217; Serial: QD000P40CA Measurement SW: DASY52, Version 52.8 (6); SEMCAD X Version 14.6.9 (7117) System Performance Check at Frequencies above 1 GHz/d=10mm, Pin=250 mW, dist=1.4mm (EX-Probe)/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 25.5 W/kg System Performance Check at Frequencies above 1 GHz/d=10mm, Pin=250 mW, dist=1.4mm (EX-Probe)/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 105.0 V/m; Power Drift = -0.09 dB Peak SAR (extrapolated) = 29.8 W/kg SAR(1 g) = 13.70 W/kg; SAR(10 g) = 6.45 W/kg Maximum value of SAR (measured) = 23.7 W/kg Page 72 of 75

ANNEX C SAR Measurement Reports Test Report No.: G0M-1601-5313-TFC093SR-V02 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 73 of 75

Date/Time: 3/22/2016 8:27:28 AM Test Laboratory: Eurofins Product Service GmbH Bluetooth DH5 - 2480MHz 0mm SAM FLAT FRONT DUT: LR-BT Class 1 Bluetooth Device; Type: CTR35 ; Serial: - Communication System: UID 0 - n/a, BT 2.4GHz DH5; Frequency: 2480 MHz;Duty Cycle: 1:1.38388 Medium: Muscle 2450 MHz Medium parameters used: f = 2480 MHz; σ = 2.049 S/m; εr = 50.343; ρ = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY5.2 Configuration: Probe: EX3DV4 - SN3893 (add ConvF); ConvF(7.6, 7.6, 7.6); Calibrated: 10/22/2015; Sensor-Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE3 Sn522; Calibrated: 9/24/2015 Phantom: SAM 12; Type: TP-1217; Serial: QD000P40CA Measurement SW: DASY52, Version 52.8 (6); SEMCAD X Version 14.6.9 (7117) Configuration/Flat Front 0mm/Area Scan (61x121x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 0.590 W/kg Configuration/Flat Front 0mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 5.054 V/m; Power Drift = 0.15 dB Peak SAR (extrapolated) = 0.715 W/kg SAR(1 g) = 0.238 W/kg; SAR(10 g) = 0.086 W/kg Maximum value of SAR (measured) = 0.455 W/kg Page 74 of 75

Date/Time: 3/22/2016 11:05:41 AM Test Laboratory: Eurofins Product Service GmbH Bluetooth DH5 - 2480MHz 0mm SAM FLAT BACK + Tablet DUT: LR-BT Class 1 Bluetooth Device; Type: CTR35 ; Serial: - Communication System: UID 0 - n/a, BT 2.4GHz DH5; Frequency: 2480 MHz;Duty Cycle: 1:1.38388 Medium: Muscle 2450 MHz Medium parameters used: f = 2480 MHz; σ = 2.049 S/m; εr = 50.343; ρ = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19-2007) DASY5.2 Configuration: Probe: EX3DV4 - SN3893 (add ConvF); ConvF(7.6, 7.6, 7.6); Calibrated: 10/22/2015; Sensor-Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE3 Sn522; Calibrated: 9/24/2015 Phantom: SAM 12; Type: TP-1217; Serial: QD000P40CA Measurement SW: DASY52, Version 52.8 (6); SEMCAD X Version 14.6.9 (7117) Configuration/Flat Back 0mm/Area Scan (61x141x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 0.0723 W/kg Configuration/Flat Back 0mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 3.939 V/m; Power Drift = 0.08 dB Peak SAR (extrapolated) = 0.0970 W/kg SAR(1 g) = 0.040 W/kg; SAR(10 g) = 0.017 W/kg Maximum value of SAR (measured) = 0.0715 W/kg Page 75 of 75


Document Created: 2017-12-06 04:25:57
Document Modified: 2017-12-06 04:25:57
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC