14a_CTR35 TestRep 15B

FCC ID: RFD-CTR35

Test Report

Download: PDF
FCCID_2997900

EMC TEST REPORT FCC 47 CFR Part 15B Industry Canada ICES-003 Electromagnetic compatibility - Unintentional radiators Report Reference No. .................... : G0M-1601-5313-EF0115B-V01 Testing Laboratory ........................ : Eurofins Product Service GmbH Address ............................................ : Storkower Str. 38c 15526 Reichenwalde Germany Accreditation .................................... : A2LA Accredited Testing Laboratory, Certificate No.: 1983.01 FCC Filed Test Laboratory, Reg.-No.: 96970 IC OATS Filing assigned code: 3470A Applicant’s name ........................... : Leica Geosystems AG Address ............................................ : Heinrich Wild Strasse 9435 Heerbrugg SWITZERLAND Test specification: Standard ........................................... : 47 CFR Part 15 Subpart B ICES-003, Issue 5:2012 ANSI C63.4:2014 Equipment under test (EUT): Product description LR-BT Class 1 Bluetooth Device Model No. CTR35 Additional Models None Hardware version Not specified Firmware / Software version 5.3.1 IDs FCC-ID: RFD-CTR35 IC: 3177A-CTR35 Test result Passed Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 1 of 24

«* eurofins | [ Product Service Possible test case verdicts: — nOt applicabl@ t0 t@St ObJ@Ct ..................c..cssmmmelt NA — test object does meet the requirement.......................:. P (Pass) — test object does not meet the requirement.................: F (Fail) Testing: Date of receipt of test item .. 2016—03—07 Date (s) of performance of tests ........................... 2016—03—18 — 2016—03—21 COMPiI@U BY ......... .ccscc : Alexander Meili Tested by (+ signature).................... : Jens Marquardt gzz;o;zfi;g/ (+ signature) ............... ; yssm men DaIG Of IBBU@ mm mmmmemmmmemmnsmme : 2016—04—18 Total number of pages..................... i0 24 General remarks: The test results presented in this report relate only to the objecttested. The results contained in this report reflect the results for this particular model and serial number. It is the responsibility of the manufacturer to ensure that all production models meet the intent of the requirements detailed within this report. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. Additional comments: Test Report No.: GOM—1601—5313—EF0115B—V01 Eurofins Product Service GmbH Storkower Str. 38c, D—15526 Reichenwalde, Germany Page 2 of 24

Version History Version Issue Date Remarks Revised by V01 2016-04-19 Initial Release Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 3 of 24

REPORT INDEX 1 EQUIPMENT (TEST ITEM) DESCRIPTION 5 1.1 Photos – Equipment external 6 1.2 Photos – Equipment internal 8 1.3 Photos – Test setup 9 1.4 Supporting Equipment Used During Testing 10 1.5 Input / Output Ports 10 1.6 Operating Modes and Configurations 11 1.7 Test Equipment Used During Testing 12 1.8 Sample emission level calculation 13 2 RESULT SUMMARY 14 3 TEST CONDITIONS AND RESULTS 15 3.1 Test Conditions and Results – Radiated emissions 15 3.2 Test Conditions and Results – AC power line conducted emissions 21 Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 4 of 24

1 Equipment (Test item) Description Description LR-BT Class 1 Bluetooth Device Model CTR35 Additional Models None Serial number Not specified Hardware version Not specified Software / Firmware version 5.3.1 FCC-ID RFD-CTR35 IC 3177A-CTR35 Power supply 5 VDC Type Bluetooth Classic Model OBS421i Manufacturer Ublox AG Radio module SW Version 5.3.1 FCC-ID PVH0946 IC 5325A-0946 Leica Geosystems AG Heinrich Wild Strasse Manufacturer 9435 Heerbrugg SWITZERLAND Highest emission frequency 108 MHz - 500 MHz (up to 2 GHz) Device classification Class B Equipment type Tabletop Number of tested samples 1 Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 5 of 24

1.4 Supporting Equipment Used During Testing Product Device Manufacturer Model No. Comments (e.g. serial no.) Type* AE Total Station Leica RH17 SN: 3100016 AE Tablet Panasonic FZ-G1FAA1LE3 SN: 5GTCA86628 AE AC/DC Adapter Panasonic CF-AA64B3C M1 Adapter for Tablet *Note: Use the following abbreviations: AE : Auxiliary/Associated Equipment, or SIM : Simulator (Not Subjected to Test) CABL : Connecting cables 1.5 Input / Output Ports Max. Cable Cable Port # Name Type* Comments (e.g. Cat. of Cable) Length Shielded 1 USB I/O n/a no Standard USB Type A Male *Note: Use the following abbreviations: AC : AC power port DC : DC power port N/E : Non electrical I/O : Signal input or output port TP : Telecommunication port Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 10 of 24

1.6 Operating Modes and Configurations Mode # Description 1 Measuring and video Configuration # EUT Configuration Device is attached to Panasonic tablet and connected to total station. Total station is 1 measuring a fix distance. Video transfer is active. Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 11 of 24

1.7 Test Equipment Used During Testing Measurement Software Description Manufacturer Name Version EMC Test Software Dare Instruments Radimation 2014.1.15 Conducted emissions Description Manufacturer Model Identifier Cal. Date Cal. Due LISN Schwarzbeck NSLK 8128 EF00975 2015-12 2016-12 EMI Test Receiver R&S ESU26 EF00887 2016-01 2017-01 Pulse Limiter R&S ESH3-Z2 EF01063 2015-05 2016-05 Radiated emissions Description Manufacturer Model Identifier Cal. Date Cal. Due TRILOG Broadband Schwarzbeck VULB 9162 EF00978 2015-10 2016-10 Antenna EMI Test Receiver R&S ESU26 EF00887 2016-01 2017-01 Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 12 of 24

1.8 Sample emission level calculation The following is a description of terms and a sample calculation, as appears in the radiated emissions data table. The numbers used in the calculation are for example only. There is no direct correlation to the specific data taken for the product described in this document: Reading: This is the reading obtained on the spectrum analyzer in dBµV. Any external preamplifiers used are taken into account through internal analyzer settings. A.F.: This is the antenna factor for the receiving antenna. It is a conversion factor, which converts electric fields strengths to voltages, which can be measured directly on the spectrum analyzer. It is treated as a loss in dB. Cable losses have been included with the A.F. to simplify the calculations. The antenna factor is used in calculations as follows: Reading on Analyzer (dBµV) + A.F. (dB) = Net field strength (dBµV/m) Net: This is the net field strength measurement (as shown above). Limit: This is the FCC Class B radiated emission limit (in units of dBµV/m). The FCC limits are given in units of µV/m. The following formula is used to convert the units of µV/m to dBµV/m: Limit (dBµV/m) = 20*log (µV/m) Margin: This is the margin of compliance below the FCC limit. The units are given in dB. A negative margin indicates the emission was below the limit. A positive margin indicates that the emission exceeds the limit. Example only: Reading + AF = Net Reading : Net reading - FCC limit = Margin 21.5 dBµV + 26 dB = 47.5 dBµV/m : 47.5 dBµV/m - 57.0 dBµV/m = -9.5 dB Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 13 of 24

2 Result Summary FCC 47 CFR Part 15B, Industry Canada ICES-003 Product Specific Reference Requirement – Test Result Remarks Standard Method 47 CFR 15.109 Radiated emissions ANSI C 63.4 PASS ICES-003 Item 6.2 47 CFR 15.107 AC power line conducted emissions ANSI C63.4 PASS ICES-003 Item 6.1 Remarks: Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 14 of 24

3 Test Conditions and Results 3.1 Test Conditions and Results – Radiated emissions Radiated emissions acc. FCC 47 CFR 15.109 / ICES-003 Verdict: PASS Laboratory Parameters: Required prior to the test During the test Ambient Temperature 15 to 35 °C 22 °C Relative Humidity 30 to 60 % 33 % Test according referenced Reference Method standards ANSI C63.4 Sample is tested with respect to the Equipment class requirements of the equipment class Class B Test frequency range determined from Highest emission frequency highest emission frequency <500 MHz Fully configured sample scanned over Frequency range the following frequency range 30 MHz to 2 GHz Operating mode 1 Configuration 1 Limits and results Class B Frequency [MHz] Quasi-Peak [dBµV/m] Result Average [dBµV/m] Result Peak [dBµV/m] Result 30 – 88 40 PASS - - - 88 – 216 43.5 PASS - - - 216 – 960 46 PASS - - - 960 – 1000 54 PASS - - - > 1000 - - 54 PASS 74 PASS Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 15 of 24

Test Procedure: The test site is in accordance with ANSI C63-4:2014 requirements and is listed by FCC. The measurement procedure is as follows: Exploratory measurement:  The EUT was placed on a non-conductive table at a height of 0.8m.  The EUT and support equipment, if needed, were set up to simulate typical usage.  Cables, of type and length specified by the manufacturer, were connected to at least one port of each type and were terminated by a device or simulating load of actual usage.  The antenna was placed at a distance of 3 or 10 m.  The received signal was monitored at the measurement receiver. o Cables not bundled were manipulated within the range of likely arrangements to produce the highest emission amplitude o To maximize the suspected emissions the EUT is rotated 360 degrees. If the signal exceeds the previous amplitude, go back to the corresponding azimuth and manipulate the cables again for maximizing the emissions if possible. o Move the antenna from 1 to 4m to maximize the suspected highest amplitude signal.  This procedure has to be performed in both antenna polarizations, horizontal and vertical.  The arrangement of the equipment with the maximum emission level is shown on the setup picture at item 1.3. Final measurement:  The EUT was placed on a 0.8 m non-conductive table at a 3 m distance from the receive antenna. The antenna output was connected to the measurement receiver  A biconical antenna was used for the frequency range 30 – 200 MHz, a logarithmic periodical antenna was used for the frequency range from 200 – 1000 MHz. Above one 1 GHz a Double Ridged Broadband Horn antenna was used. The antenna was placed on an adjustable height antenna mast  The EUT and cable arrangement were based on the exploratory measurement results  Emissions were maximized at each frequency by rotating the EUT and adjusting the receive antenna height and polarization. The maximum values were recorded.  The test data of the worst-case conditions were recorded and shown on the next pages. Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 16 of 24

Spurious emissions under normal conditions according to FCC 47 CFR 15.107 / ICES-003 Project number: G0M-1601-5313 Applicant: Leica Geosystems EUT Name: LR-BT Class1 Bluetooth Device Model: CTR35 Test Site: Eurofins Product Service GmbH Operator: Mr. Meili Test Conditions: Tnom: 22°C, Unom: 5VDC USB Antenna: Schwarzbeck VULB 9162, Horizontal Measurement distance: 3m Mode: Connected, measuring Test Date: 2016-03-18 Note: Index 5 FCC §15.109 Class B QP RBW: 120 kHz, Horizontal Max Peak 60 50 40 Electrical Field (dBµV/m) 30 20 10 0 -10 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 17 of 24

Spurious emissions under normal conditions according to FCC 47 CFR 15.107 / ICES-003 Project number: G0M-1601-5313 Applicant: Leica Geosystems EUT Name: LR-BT Class1 Bluetooth Device Model: CTR35 Test Site: Eurofins Product Service GmbH Operator: Mr. Meili Test Conditions: Tnom: 22°C, Unom: 5VDC USB Antenna: Schwarzbeck VULB 9162, Vertical Measurement distance: 3m Mode: Connected, measuring Test Date: 2016-03-18 Note: Index 6 FCC §15.109 Class B QP RBW: 120 kHz, Vertical Max Peak 60 50 40 Electrical Field (dBµV/m) 30 20 10 0 -10 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 18 of 24

Spurious emissions under normal conditions according to FCC 47 CFR 15.107 / ICES-003 Project number: G0M-1601-5313 Applicant: Leica Geosystems EUT Name: LR-BT Class1 Bluetooth Device Model: CTR35 Test Site: Eurofins Product Service GmbH Operator: Mr. Meili Test Conditions: Tnom: 22°C, Unom: 5VDC USB Antenna: Schwarzbeck VULB 9162, Vertical Measurement distance: 3m Mode: Connected, measuring Test Date: 2016-03-18 Note: Index 7 FCC §15.109 Class B AV FCC §15.109 Class B PK RBW: 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 80 70 60 Electrical Field (dBµV/m) 50 40 30 20 10 1G 1.2 G 1.4 G 1.6 G 1.8 G 2G Frequency (Hz) Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 19 of 24

Spurious emissions under normal conditions according to FCC 47 CFR 15.107 / ICES-003 Project number: G0M-1601-5313 Applicant: Leica Geosystems EUT Name: LR-BT Class1 Bluetooth Device Model: CTR35 Test Site: Eurofins Product Service GmbH Operator: Mr. Meili Test Conditions: Tnom: 22°C, Unom: 5VDC USB Antenna: Schwarzbeck VULB 9162, Horizontal Measurement distance: 3m Mode: Connected, measuring Test Date: 2016-03-18 Note: Index 8 FCC §15.109 Class B AV FCC §15.109 Class B PK RBW: 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 80 70 60 Electrical Field (dBµV/m) 50 40 30 20 10 1G 1.2 G 1.4 G 1.6 G 1.8 G 2G Frequency (Hz) Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 20 of 24

3.2 Test Conditions and Results – AC power line conducted emissions Conducted emissions acc. FCC 47 CFR 15.107 / ICES-003 Verdict: PASS Laboratory Parameters: Required prior to the test During the test Ambient Temperature 15 to 35 °C 22 °C Relative Humidity 30 to 60 % 33 % Test according referenced Reference Method standards ANSI C63.4 Fully configured sample scanned over Frequency range the following frequency range 0.15 MHz to 30 MHz Sample is tested with respect to the Equipment class requirements of the equipment class Class B Points of Application Application Interface AC Mains LISN Operating mode 1 Configuration 1 Limits and results Class B Frequency [MHz] Quasi-Peak [dBµV] Result Average [dBµV] Result 0.15 to 5 66 to 56* PASS 56 to 46* PASS 0.5 to 5 56 PASS 46 PASS 5 to 30 60 PASS 50 PASS Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 21 of 24

Test Procedure: The test site is in accordance with ANSI C63-4:2014 requirements and is listed by FCC. The measurement procedure is as follows: Exploratory measurement:  The EUT was placed on a non conductive table 0.8 m above the reference ground plane and 0.4 m away from the vertical conducting plane (ANSI C63.4: 2014 item 7.3.1)  The power cord that is normally supplied or recommended by the manufacturer was connected to the LISN.  The distance between the outer edge of the EUT and the LISN shall be set to 0.8 m. A longer power cord shall be bundled to this length (bundling shall not exceed 40 cm in length).  The LISN measurement port was connected to a measurement receiver  I/O cables were bundled not longer than 0.4 m  Measurement was performed in the frequency range 0.15 – 30MHz on each current-carrying conductor  To maximize the emissions the cable positions were manipulated  The worst configuration of EUT and cables is shown on a test setup picture at item 1.3 Test Procedure: Final measurement:  The EUT was placed on a non conductive table 0.8 m above the reference ground plane and 0.4 m away from the vertical conducting plane (ANSI C63.4: 2014 item 7.3.1)  The power cord that is normally supplied or recommended by the manufacturer was connected to the LISN.  The distance between the outer edge of the EUT and the LISN shall be set to 0.8 m. A longer power cord shall be bundled to this length (bundling shall not exceed 40 cm in length).  The LISN measurement port was connected to a measurement receiver  The EUT and cable arrangement were based on the exploratory measurement results  The test data of the worst-case conditions were recorded and shown on the next pages. Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 22 of 24

EMI voltage test in the ac-mains according to FCC 47 CFR 15.107 / ICES-003 Project number: G0M-1601-5313 Applicant: Leica Geosystems EUT Name: LR-BT Class1 Bluetooth Device Model: CTR35 Test Site: Eurofins Product Service GmbH Operator: Mr. Meili Test Conditions: Tnom: 22°C, Unom: 5VDC USB via AC/DC-Adapter from Tablet LISN: Schwarzbeck NSLK 8128 (N) Mode: Connected, measuring, charging Test Date: 2016-03-21 Note: Index 9 FCC §15.107 Class B AV FCC §15.107 Class B QP RBW: 9 kHz, Neutral Max Average RBW: 9 kHz, Neutral Max Peak 80 70 60 50 Voltage (dBµV) 40 30 20 10 0 -10 150 k 300 k 500 k600 k 1M 2M 3M 5M 10 M 20 M 30 M Frequency (Hz) Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 23 of 24

EMI voltage test in the ac-mains according to FCC 47 CFR 15.107 / ICES-003 Project number: G0M-1601-5313 Applicant: Leica Geosystems EUT Name: LR-BT Class1 Bluetooth Device Model: CTR35 Test Site: Eurofins Product Service GmbH Operator: Mr. Meili Test Conditions: Tnom: 22°C, Unom: 5VDC USB via AC/DC-Adapter from Tablet LISN: Schwarzbeck NSLK 8128 (L) Mode: Connected, measuring, charging Test Date: 2016-03-21 Note: Index 10 FCC §15.107 Class B AV FCC §15.107 Class B QP RBW: 9 kHz, Line 1 Max Average RBW: 9 kHz, Line 1 Max Peak 80 70 60 50 Voltage (dBµV) 40 30 20 10 0 -10 150 k 300 k 500 k600 k 1M 2M 3M 5M 10 M 20 M 30 M Frequency (Hz) Test Report No.: G0M-1601-5313-EF0115B-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 24 of 24


Document Created: 2017-12-06 04:22:19
Document Modified: 2017-12-06 04:22:19
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC