Test Report 3

FCC ID: RAX7904WBRA-N

Test Report

Download: PDF
FCCID_869660

4.6.4 DEVIATION FROM TEST STANDARD No deviation 4.6.5 EUT OPERATING CONDITION Same as Item 4.3.6 4.6.6 TEST RESULTS The spectrum plots are attached on the following 12 images. D1 line indicates the highest level, and D2 line indicates the 20dB offset below D1. It shows compliance with the requirement in part 15.247(d). Report No.: RF960726H09 91 Report Format Version 2.0.6

802.11b DSSS MODULATION: CH1 CH11 Report No.: RF960726H09 92 Report Format Version 2.0.6

CH1 CH11 Report No.: RF960726H09 93 Report Format Version 2.0.6

802.11g OFDM MODULATION: CH 1 CH11 Report No.: RF960726H09 94 Report Format Version 2.0.6

CH1 CH11 Report No.: RF960726H09 95 Report Format Version 2.0.6

DRAFT 802.11n (20MHz) OFDM MODULATION: For Chain (0):CH1 CH11 Report No.: RF960726H09 96 Report Format Version 2.0.6

CH1 CH11 Report No.: RF960726H09 97 Report Format Version 2.0.6

For Chain (1):CH1 CH11 Report No.: RF960726H09 98 Report Format Version 2.0.6

CH1 CH11 Report No.: RF960726H09 99 Report Format Version 2.0.6

DRAFT 802.11n (40MHz) OFDM MODULATION: For Chain (0):CH1 CH7 Report No.: RF960726H09 100 Report Format Version 2.0.6

CH1 CH7 Report No.: RF960726H09 101 Report Format Version 2.0.6

For Chain (1):CH1 CH7 Report No.: RF960726H09 102 Report Format Version 2.0.6

CH1 CH7 Report No.: RF960726H09 103 Report Format Version 2.0.6

4.7 ANTENNA REQUIREMENT 4.7.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 4.7.2 ANTENNA CONNECTED CONSTRUCTION There are three antennas provided to this EUT, please refer to the following table: No. Antenna Type Antenna Connector Gain(dBi) 1 Dipole NA 3.5 2 PIFA NA 2 3 Dipole NA 3.5 Report No.: RF960726H09 104 Report Format Version 2.0.6

5. INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025. USA FCC, UL, A2LA Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA , CSA R.O.C. TAF, BSMI, NCC Netherlands Telefication Singapore GOST-ASIA(MOU) Russia CERTIS(MOU) Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26052943 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050 Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also Report No.: RF960726H09 105 Report Format Version 2.0.6

6.APPENDIX-A- MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications are made to the EUT by the lab during the test. Report No.: RF960726H09 106 Report Format Version 2.0.6


Document Created: 2007-11-13 14:41:32
Document Modified: 2007-11-13 14:41:32
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC