2013SAR00065_Rev02_part3

FCC ID: RAD330

RF Exposure Info

Download: PDF
FCCID_1995678

TME Impedance Measurement Plot for Body TSL 9 May 2012 12:80i94 CB] si 1 U re 1t46.815 6 ~783400 24.330 pF 835.000 000 Mz Cha Markers ne 1 2 86745 6 tor 27.27? 208.060 Mzo h 158 Hd on2 CH2 Mankens Cor 2e41.953 4e 200.000 Mitz By 18° HId Certificate No: DB5V2—443_May12 Page 8 of 8

TME e Calibration Laboratory of Schwelzerischer Kalibrierdenst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zoughausstrasse 43, 8004 Zurich, Switzerland Swiss Callbration Service Accredited by the Swiss Accreditation Service (GAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of thesignatories to the EA Multifateral Agreement forthe recognition of calibration cartificates Client (TMC Beijfing CertificateNo: D1750V2—1003_May12 [CALIBRATION CERTIFICATE Object D1750V2 — SN: 1003 Celibration procedure(s) Ga cat—osve Calibration procedure for dipole validation kits above 700 MHz Calibration date: May 08, 2012 This calibration centficate documents the traceabilty to national standards, which realize the physical units of measurements (1) The measurements and the uncertainties with confidence probabilty are given on the following pages and are part of the certificate. All callbrations have bean conducted in the closed laboratory facility: environment temparature (22 > 3}°C and humidity < 70%. Calibration Equipment used (MBTE critical for calibration} Primary Standards 10 & Cal Date (Cerificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 06—Oct—11 (No. 217—01451) Oct—12 Power sensor HP 8481A usar2027es O5—Oct—11 (No. 217—01451) Oct—12 Reterence 20 dB Attenuator SN: 5058 (20k) 27—Mat—12 (No. 217—01830) Aprid Type—N mismatch combination SN: 5047.2 / 06827 27—Mar—12 (No. 217—01533) Aprd Relerence Probe ES3DVS SN: 8205 0—Dec—11 (No. ES3—8205_Dect1) Dec—12 DaAE4 SN: 601 04—Jul—11 (No. DAE4—601_Jult1) Jul—12 Secondary Standards 10 Check Date (in house) Scheduled Check Power sensor HP 8481A MY41092317 18—Oct—02 (in house checkOct—11) in house check: Oct—13 RF generator RAS SMT—06 100006 04—Aug—29 (in house chack Oct—11) In house check: Oct—13 Network Analyzer HP 8763E USg7390505 $4206 18—Oct—01 (In house chack Oct—11) In house checic: Oct—12 Name Function Signature Callbrated by: Dimce lliew Lammmy Technician Approved by: Katja Pokovic Technical Manager Issuad: May 8, 2012 This callbration certificate shall not be reproduced except in full without written approval of the laboratory Certificate No: D1750V2—1008_May12 Page 1 of 8

TMCE Calibration Laboratory of . Schwelzerischer Kalibrierdienst Schmid & Partner c Service sulsse d‘stalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multifateral Agreement for the recognition of callbration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®", December 2003 b) 12C 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) Federal Communications Commission Office of Engineering & Technology (FCC OET}, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. + SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D1750V2—1003_May12 Page 2 of 8

TME« e Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V62.8.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 1750 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0°C 40.1 1.37 mho/m Measured Head TSL parameters (22.0 2 0.2) °C 40.5 2 6 % 1.34 mho/m x 6 % Head TSL temperature change during test <0.5°C «o «o SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 8.91 mW /g SAR for nominal Head TSL paramaters normalized to 1W 36.2 mW /g x 17.0 % (k=2) SAR averaged over 10 em* (10 g) of Head TSL condition SAR measured 250 mW input power 4.77 mW / q SAR for nomina! Head TSL parameters normalized to 1W 19.3 mW /g + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.4 1.49 mho/m Measured Body TSL parameters (22.0 x 0.2) °C §2.0 16 % 1.46 mho/m £ 6 % Body TSL temperature change during test <0.5°C se ssm SAR result with Body TSL SAR averaged over 1 cm° (1 g) of Body TSL Condition SAR measured 250 mW input power 9.26 mW / g SAR for nominal Body TSL parameters normalized to 1W 37.4 mW / g « 17.0 % (k=2) SAR averaged over 10 em* (10 g) of Body TSL condition SAR measured 250 mW input power 5.00 mW /g SAR for nominal Body TSL parameters normalized to 1W 20.1 mW / g x 16.5 % (k=2) Cortificate No: D1750V2—1003_May12 Page 3 of 8

TMLI Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 50.3 0 + 1.3 jQ Return Loss —87.5 d8 Antenna Parameters with Body TSL Impedance, transformed to feed point 45.7 2 +1.2 j0 Return Loss ~26.6 4B General Antenna Parameters and Design | Electrical Delay (one direction) 1.215 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxia!l cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—cirouited for DC—signals. On some of the dipales, small end caps are added to the dipole armsin order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessiveforce must be applied to the dipole arms, because they might bend or the soldered connections nearthe feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on July 30, 2008 Corlificate No: D1750V2—1003_May12 Page 4 of 8

TMCE h DASYS Validation Report for Head TSL Date: 08.05.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1750 MHz; Type: D1750V2; Serial: D1750V2 — SN: 1003 Communication System: CW; Frequency: 1750 MHz Medium parameters used: £ = 1750 MHz: 0 = 1.34 mho/m; £, =40.5; p = 1000 kgfm‘ Phantom section; Flat Section Measurement Standard: DASY3 (IEEE/IEC/ANSI €63.19—2007) DASY52 Configuration: + Probe: ES3DYV3 — SN3205; ConvF(5.22, 5.22, 5.22); Calibrated: 30.12.2011; + Sensor—Surface: 3mm (Mechanical Surface Detection) + Electronics: DAE4 Sn601; Calibrated: 04.07.201 1 + Phantom: Flat Phantom 5.0 (front); Type: QDOOOP30AA; Serial: 1001 + DASY52 52.8.1(838); SEMCAD X 14.6.5(6469) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid; dx=5mm.,dy=5mm, dz=3mm Reference Value = 93.753 V/m; PowerDrift = 0.04 dB Peak SAR (extrapolated) = 15.720 mW/g SAR(I g) = 8.91 mW/g; SAR(IO g) = 4.77 mW/g Maximum value of SAR (measured) = 11.0 mW/g zeo snn aaan 0 dB = 11.0 mW/g= 20.83 dB mW/g Certificate No: D1750V2—1008_May12 Page 5 of 8

TME« e Impedance Measurement Plot for Head TSL 8 May 2012 10:09107 CH]) sit i U FS 1: 50.250 a 1.3184 6 419.90 pH 1 750,000 000 MHz Ay 165 Hid CH2 Cor B 159 HId Certificate No: D1750V2—1003_May12 Page 6 of 8

TMCE DASY5 Validation Report for Body TSL Date: 08.05.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1750 MHz; Type: D1750V2; Serial: D1750V2 — SN: 1003 Communication System: CW; Frequency: 1750 MHz Medium parameters used: f= 1750 MHz; 0 = 1.46 mho/m; &, = 52.9; p = 1000 kg/m" Phantomsection: Flat Section Measurement Standard: DASYS (IEEEAIEC/ANSI €63.19—2007) DASY52 Configuration: + Probe: ES3DV3 — SN3205; ConyF(4.85, 4.85, 4.85); Calibrated: 30.12.2011; «+ Sensor—Surface: 3mm (Mechanical Surface Detection) + Electronics: DAE4 Sn601; Calibrated: 04.07.201 1 + Phantom: Flat Phantom 5.0 (back); Type: QDOOOPSOAA; Serial: 1002 + DASY52 52.8.1(838); SEMCAD X 14.6.5(6469) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 93.095 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 15.760 mW/g SAR(I g) = 9.26 mW/g; SAR(1O g) = 5 mW/g Maximum value of SAR (measured) = 11.6 mW/g ve.0 1600 0 dB = 11.6 mW/g= 21.29 dB mW/g Cartificate No: D1750V2—1008_May12 Page 7 of 8

TME« e Impedance Measurement Plot for Body TSL 8 May 2012 1gi87ii0 s1t 1 uo Fe 11456908 14075 a 108.00 pH 1 750.000 008 MHz fvg 16 Hid CH2 ty 16° Hid st 1 $50.a00 thiz StoP 2 iz Certificate No: D1750V2—1003_May12 Page 8 of 8

TME e Calibration Laboratory of wul, g SchweizerischerKalibrierdienst . i Schmid & Partner w\_/& c Service suissed‘étalonnage Engineering AG en Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ns itant, Swiss Callbration Service ltb Aceredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of callbration certificates client (TMC Beijing Certificate No: D1900V2—541_May12 CALIBRATION CERTIFICATE Object D1900V2 — SN: 541 Calibration procedure(s) QA CAL—05.v8 Calibrationprocedurefor dipole validation kitsabove 700 MHz Calibration date: May 09, 2012 This callbration certificate documents the traceabilty to national standards, which realize the physical units of measurements (S1). The measurements and the uncartaintios with confidence probabilty are given on the following pages and are part of the cartificato. All calibrations have bean condusted in the closed laboratory facilty: environment temperature (22 « 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Gortiicate No.) Schedulad Calibration Power meter EPM—442A GB37480704 05—Oct—11 (No. 217—01451) Oct12 Power sensorHP 8481A usarzor7es 05—O0ct—11 (No. 217—01451) Oct12 Raference 20 dB Attenuator N: sose (20k) 27—Mar12 (No. 217—01590) Apris Type—N mismatch combination SN: 5047.2 / 0esa7 27—Mar12 (No. 217—01599) Apr18 Raference Probe ESBDV3 SN: 9205 0—Dec—11 (No. ES3—8205_Dect1) Dec—12 Dag4 SN: co1 04—Jul—11 (No. DAE4—601_Jul11) dul—t2 Secondary Standards ID # Check Date (in house) Schedulad Check Power sensor HP 8481A MY41002317 18—Oct—02 (in house check Oct—11) In house chack: Oct—13 RF gensrator R&S SMT—06 100005 04—Aug—98 (in house check Oct—11) In house chack: Oct—18 Network Analyzer HP 8753E Usereanses $4206 18—Oct—01 (inhouseccheck Oct—11) in house chack: Oct—12 Name Function Signature Callbrated by: IsraeE—Naouq Laboratory Tevh_nibim Approved by: Katja Pokovie Technical Manager _fi“??4_ Issued: May 9, 2012 This callbration cortificate shall not be repreduced excapt in full without written approval of the laboratory. Certificate No: D1900V2—541_May12 Page 1 of 8

TMCE i 4 soltn, Calibration Laboratory of plssoh G Schweizerischer Kalibrierdienst Schmid & Partner ;ila‘\\e?//mfié c Service suisse d‘étalonnage Engineering AG T * =g Servizlo svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland “,,,,fi\‘g S swiss Calibration Service "ulal® Accredited by the Siwiss Accreditation Service (5AS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of thesignatories to the EA Multilateral Agreementfor the recognitionof calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) 1EC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) Federal Communications Commission Office of Engineering & Technology (FCC OET}, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions‘, Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. «_ Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. «_ Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. «_ Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D1900V2—641_May12 Page 2 of 8

TMLI Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DaASYS V52.8.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 1900 MHz a 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0°C 40.0 1.40 mho/m Measured Head TSL parameters (22.0 2 0.2) °C 40.5 x 6 % 1.37 mho/m 2 6 Head TSL temperature change during test <0.5°C «—— ——— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 9.62 mW / g SAR for nominal Head TSL parameters normalized to 1W 39.1 mW /g + 17.0 % (k=2) SAR averaged over 10 em* (10 g) of Head TSL condition SAR measured 250 mW input power 5.11 mW /g SAR for nominal Head TSL parameters normalized to 1W 20.6 mW /g = 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.62 mho/m Measured Body TSL parameters (22.0 0.2) °C §2.9 £ 6 % 1.52 mho/m a 6 % Body TSL temperature change during test <0.5°C m mss SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 10.0 mW /g SAR for nominal Body TSL parameters normalized to 1W 39.9 mW / g a 17.0 % (k=2) SAR averaged over 10 em> (10 g) of Body TSL condition SAR measured 250 mW input power 5.33 mW /g SAR for nominal Bady TSL parameters normalized to 1W 21.3 mW / g « 16.5 % (k=2) Cartificate No: D1900V2—541_May12 Page 3 of 8

TMLI Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point §2.6 0 + 6.2 jQ Return Loss —23.7 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 48.6 0 + 6.9 jQ Return Loss —23.0 dB General Antenna Parameters and Design { Electrical Delay (one direction) ] 1.197 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions® paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipols arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manulactured by SPEAG Manulactured on July 26, 2001 Certificate No: D1900V2—541_May12 Page 4 of 8

TME L DASY5 Validation Report for Head TSL Date: 09.05.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN: 541 Communication System: CW; Frequency: 1900 MHz Medium parameters used: f = 1900 MHz; a= 1.37 mho/m; &, = 40.5; p = 1000 kg m‘ Phantom section: Flat Section Measurement Standard: DASYS (IEEE/TEC/ANSI C63.19—2007) DASY32 Configuration: s Probe: ES3DV3 — SN3205; ConvF(5.01, 5.01, 5.01); Calibrated: 30.12.2011; « Sensor—Surface: 3mm (Mechanical Surface Detection) « Electronics: DAE4 Sn601; Calibrated: 04.07.201 1 + Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50AA; Serial: 1001 + DASY52 52.8.1(838); SEMCAD X 14.6.5(6469) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 96.763 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 17.071 mW/g SAR(I g) = 9.62 mW/g; SAR(10 g) = 5.11 mWi/g Maximum value of SAR (measured) = 12.0 mW/g —3.60 —1.20 10.80 "14.40 18.00 0 dB = 12.0 mW/g =21.58 dB mW/g Certificate No: D1900V2—541_May12 Page 5 of 8

TME e Impedance Measurement Plot for Head TSL 9 May 2012 ©9i¢4:17 C sar 4 uce 11525920 61095 518.46 pH 1 900.000 000 Mz dvi ts° Hig Certificate No: D1900V2—541_May12 Page 6 of 8

TMLI DASYS Validation Report for Body TSL Date: 04.05.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN: 541 Communication System: CW; Frequency: 1900 MHz Medium parameters used: f = 1900 MHz; a= 1.52 mho/m:; & = 52.9; p = 1000 kgfm\ Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2007) DASY32 Configuration: Probe: ES3DV3 — SN3205; ConvF(4.62, 4.62, 4.62); Calibrated: 30.12.2011; Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAE4 Sn601; Calibrated: 04.07.201 1 Phantom: Flat Phantom5.0 (back); Type: QDOOOP3OAA; Serial: 1002 DASY52 52.8.1(838); SEMCAD X 14.6.5(6469) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value =95.165 V/m; Power Drift = —0.01 dB Peak SAR (extrapolated) = 17.442 mW/g SAR(I g) = 10 mW/g; SAR(10 g) = 5.33 mW/g Maximum value of SAR (measured) = 12.7 mW/g dB 0 —3.60 —7.20 10.80 —14.40 18.00 0 dB = 12.7 mW/g = 22.08 dB mW/g Cartificate No: D1900V2—541_May12 Page 7 of 8

TME« e Impedance Measurement Plot for Body TSL 4 May 2012. irri4nd1 CBI sn i ue 1149.5720 699720 575.24 pH 1 $60.000 000 MHz Dei Cor fv is° Hid cH2 Cor hy lEs H1d Cartificate No: D1900V2—541_May12 Page 8 of 8

TME 2 Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service sulsse d‘étalonnage Engineering AG Servizio svizzero di taratura Zoughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of callbration certificates Ciient TMC Beijing Certificate No: D2450V2—853_May12 CALIBRATION CERTIFICATE § Object D2450V2 — SN: a53 Callbration procedure(s) QA CAL—05.v8 Calibration procedure for dipole validation kitsabove 700 MHz Callbration date: May 02, 2012 This callbration certificate documents the traceabilty to national standards, which reelize the physical units of measurements (81). The measurements and the uncertainties with confidenceprobabiity are given on the following pages and are part of the cortiicate. All eallbrations have been conducted in the closed laboratory facility; environment temperature (22 # 3)°C and humidity < 70%. Callbration Equipment used (METE critical for caltbration) Primary Standards ID # Cal Date (Certificate No.) Schadulad Calibration Power mater EPM—442A GB37480704 05—Oct—11 (No. 217—01451) Oct—12 Power sensor HP 8481A US97202703 05—Oct—11 (No. 217—01451) Oct—12 Reference 20 0B Attenuator SN: 5058 (20k) 27—Mar—12 (No. 217—01530) Apr18 Type—N mismatch combination SN: 50472 / 06327 27—Mar—12 (No. 217—01533) Apr18 Reference Probe ES3DV3 SN: 8205 80:Dec—11 (No. ESS—8205_Dect1) Dec—12 Daga SN: s01 O4—jul—11 (No. DAE4—601_Jul11) Jubt2 Secondary Standards iD # Check Date (in house) Schadulad Check Power sensor HP 8481A MVA1092317 18—Oct—02 (in house check Oct—11} in house check: Oct—13 AF generator R&S SMT—06 100005 04—Aug—99 (in housecheck Oct—11) in house cheok: Oct—13 Network Analyzer HP 8753E US87390585 4206 18—Oct—01 (in house check Oot—11) in house cheok; Oct—12 Name Function Signature Calibrated by: Israe E—Naouq Laboratory Technician . (.L‘".- ‘Cta L 'u‘\ Approved by: Katja Pokovie Technical Minager ”% Issued: May 2, 2012 This callbration certificate shall not be reproduced except in full without witten approval of the laboratory. Crtificate No: D2450V2—853_May12 ° Page 1 of 8

TME« ue Calibration Laboratory of Schweizerischer Kallbrierdienst Schmid & Partner Service suisse u'élalormage Engineering AG Servizio svizzero d taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Callbration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Serviceis one of the signatories to the EA Muftilatera! Agreement for the recognition of callbration certiticates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 c) Federal Communications Commission Office of Engineering & Technology (FCC OET), "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields; Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions", Supplement C (Edition 01—01) to Bulletin 65 Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—853_May12 Page 2 of 8

TME« e Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASYS V52.8.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 2450 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 £0.2) °C 39.6 26 % 1.81 mho/m « 6 % Head TSL temperature change during test <0.5°C hss s« SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 13.1 mW /g SAR for nominal Head TSL parameters normalized to 1 W 52.4 mW /g £ 17.0 % (k=2) SAR averaged over 10 cm* {10 g) of Head TSL condition SAR measured 250 mW input power 6.09 mW /g SAR for nominal Head TSL parameters normalized to 1W 24.4 mW /g + 16.5 % (k=2) Body TSL parameters Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 £0.2) °C 52.4 + 6 % 1.98 mho/m + 6 % Body TSL temperature change during test <0.5°C m SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 12.7 mW /g SAR for nominal Body TSL parameters normalized to 1W 50.4 mW / g x 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 250 mW input power 5.92 mW /g SAR for nominal Body TSL parameters normalized to 1W 23.6 mW / g + 16.5 % (k=2) Cartificate No: D2450V2—053_May12 Page 3 of 8

TME« e Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 53.7 0 +3.2 0 Return Loss ~26.4 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 49.9 Q + 4.8 Jn Return Loss —26.4 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.1693 ns After long term use with 100W radiated power, only a stight warming of the dipole near thefeedpoint can be measured. The dipole is made of standard semirigid coaxia! cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in arder to improve matching when loaded according to the position as explained in the *Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on November 10, 2009 Certificate No: D2450V2—053_May12 Page 4 of 5

TME« L DASY5 Validation Report for Head TSL Date: 02,05.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 853 Communication System: CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz: 0 = 1.81 mho/m: &, = 39.6; p= 1000 kgf‘mj Phantom section: Flat Section Measurement Standard: DASY3 (IEEE/AIEC/ANSI C63.19—2007) DASY32 Configuration: «_ Probe: ES3DV3 — $SN3205; ConvF(4.45, 4.45, 4.45); Calibrated: 30.12.2011; « Sensor—Surface: 3mm (Mechanical Surface Detection) + Electronics: DAE4 Sn601; Calibrated: 04.07.2011 «_ Phantom: Flat Phantom 5.0 (front); Type: QDOOOP5OAA; Serial: 1001 «_ DASY32 52.8.1(838); SEMCAD X 14.6.5(6469) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 100.0 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 26.785 mW/g SAR(I g) = 13.1 mW/g; SAR(10 g) = 6.09 mW/g Maximum value of SAR (measured) = 16.7 mW/g 5.20 10.40 ~15.60 —20.80 —26.00 0 dB = 16.7 mW/g =24.45 dB mWi/g Certificate No: D2450V2—853_May12 Page 5 of 8

TME« e Impedance Measurement Plot for Head TSL 2 May 2012 18110128 CHM s1 i U Fs i8a736a 3,.2309e 210.36 pH 2 450,000 008 MHz Del Ca & 16 H1d cha Avi 16° Hd st 250.000 600 MHz SToP 2 650.000 900 Mz Cartificate No: D2450V2—855_May12 Page 6 of 8

TME« e DASYS Validation Report for Body TSL Date: 02.05.2012 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial; D2450V2 — SN: 853 Communication System: CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz: a= 1.98 mho/m; s, = 52.4; p= 1000 kgfl'lfl‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY52 Configuration: «+ Probe: ES3DV3 — SN3205; ConvF(4.26, 4.26, 4.26); Calibrated: 30.12.2011; « Sensor—Surface: 3mm (Mechanical Surface Detection) + Electronics: DAE4 Sn601; Calibrated: 04.07.201 1 Phantom: Flat Phantom 5.0 (back); Type: QDOOOPSOAA; Serial: 1002 «— DASY52 52.8.1(838); SEMCAD X 14.6.5(6469) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 95.306 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 26.029 mW/g SAR(I g) = 12.7 mW/g; SAR(10 g) = 5.92 mW/g Maximum value of SAR (measured) = 16.8 mW/g ~4.80 —9.60 —14.40 "19.20 ~24.00 0 dB = 16.8 mW/g = 24.51 dB mW/g Cartificate No: D2450V2—853_May12 Page 7 of 8

TMEI h Impedance Measurement Plot for Body TSL 2 May 2o12 aszooist CHD sin a ues 1:49.896 6 4.8027 8. 11.99 pH 2 4se.000 ooo mHz Ded Ca ie 16 ma CHa2 By 159 Hia SthRt 2 250.000 000 Mz STuP 2 650.000 00 Miz Cartificate No: D2450V2—853_May12 Page 8 of 8

No. 2013SAR00065 Page 151 of 151 ANNEX I DIPOLE QUALIFICATION FOR THE EXTENDED 3-YEAR CALIBRATION INTERVAL I1 Dipole 1900 The information and documentation below are provided to qualify the extended 3-year calibration interval of dipole. I1.1 List of Equipment No. Name Type Serial Number 01 Network analyzer E5071C MY46110673 02 Power meter NRVD 102083 03 Power sensor NRV-Z5 100542 04 Signal Generator E4438C MY49070393 05 Amplifier 60S1G4 0331848 06 E-field Probe SPEAG EX3DV4 3846 07 DAE SPEAG DAE4 771 08 Dipole Validation Kit SPEAG D1900V2 541 I1.2 Results of Impedance, Return-loss and System validation Dipole 1900 - Head Year Deviation Limit 2012 2013 Real (Ω) 52.6 50.7 -1.9Ω Deviation < 5Ω Impedance Imaginary (Ω) 6.2 2.5 -3.7Ω Deviation < 5Ω Return-loss (dB) -23.7 -23.5 0.2dB Deviate < 0.2dB System 10g 5.11 5.07 -0.78% Deviation < 10% validation 1g 9.62 9.61 -0.10% Deviation < 10% Dipole 1900 - Body Year Deviation Limit 2012 2013 Real (Ω) 48.6 47.1 -1.5Ω Deviation < 5Ω Impedance Imaginary (Ω) 6.9 3.3 -3.6Ω Deviation < 5Ω Return-loss (dB) -23.0 -23.1 -0.1dB Deviate < 0.2dB System 10g 5.33 5.46 2.44% Deviation < 10% validation 1g 10 10.3 3.00% Deviation < 10% According to the above tables, it is not necessary to recalibration the dipoles in 2013.


Document Created: 2013-06-19 08:38:38
Document Modified: 2013-06-19 08:38:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC