Test Report

FCC ID: R9C-X909

Test Report

Download: PDF
FCCID_1894311

Report No.:§Z12120080E02 377y ORLAB: FCC TEST REPORT Issuedto GUANGDONG OPPO MOBILE TELECOMMUNICATIONS CORP., LTD. For WCDMA Digital Mobile Phone Model Name OPPO Xx909 Trade Name OPPO Brand Name OPPO FCC ID R9C—x909 Standard 47 CFR Part 15 Subpart C Test date December 20, 2012 — January 15, 2013 Issue date January 28, 2013 By Tested by XK?G.Q xrflj App io Xiong Huang Pulong (Test Engineer) (EMC Manager) Date 7_0,*5' IJ}/ Date Date ’U’; {"Lr Authorized san cone ssoerssaco L@OJaRY es GC E* 1 ©@Bluetooth; FCC es ctca Ond IEEE 1725 oTA ;E% s sincotreets taw BaTF 695796 The report efers onls to the sample tested and does not applyto the bulk: This report is issued in confidence to the elient and it will be strietly traated as such by the Shenien MORLAB Commuication Technology Co.. Ltd. It may not be reprodiiced rather in ts entiety or in part and it may not be usedfor adverting. The client to whom the report is issied may, howeser showor send ar a certfied eopythere ofprepared by the Shenzhen MORLAB Telecommunication Co., Lid to Ais eustomer Supplier orothers persons directlyconcemed. Shenzhen MORLAR Telecommunication Co. Ltd will nt, withont the consent of the client enter into unydiscussion of earrespondence with anythind party cancerning the contents ofthe report Inthe event ofthe improper use ofthe report, Shenzhen MORLAB Telecommunication Co.. Ltdreserves the rightsto withdraw it nd to adapt anyother remedies which maybe appropriate Shenzhen MORLAB Communication Technology Co., Ltd Tol +86 755 366 F. 3, Building A, Fei¥ang Scrence Pask, No# LongChing Road. lock 67, BaoAn District, ShonZhen. Guing

Report No.: SZ12120080E02 TABLE OF CONTENTS 1. GENERAL INFORMATION ....................................................................................................4 1.1 EUT Description .........................................................................................................................4 1.2 Test Standards and Results ........................................................................................................5 1.3 Facilities and Accreditations ......................................................................................................6 1.3.1 Facilities ....................................................................................................................................6 1.3.2 Test Environment Conditions ....................................................................................................6 1.3.3 Measurement Uncertainty .........................................................................................................6 2. 47 CFR PART 15C REQUIREMENTS ....................................................................................7 2.1 Antenna requirement .................................................................................................................7 2.1.1 Applicable Standard ..................................................................................................................7 2.2 Conducted Emission ...................................................................................................................8 2.2.1 Test Requirement ......................................................................................................................8 2.2.2 Test Equipment..........................................................................................................................8 2.2.3 Test Setup ..................................................................................................................................9 2.2.4 Test Result .................................................................................................................................9 2.3 Radiated Emission .................................................................................................................... 11 2.3.1 Test Requirement .................................................................................................................... 11 2.3.2 Test Equipment........................................................................................................................12 2.3.3 Test Setup ................................................................................................................................12 2.3.4 Test Result ...............................................................................................................................14 2.4 Frequency Tolerance ................................................................................................................17 2.4.1 Test Requirement ....................................................................................................................17 2.4.2 Test Equipment........................................................................................................................17 2.4.3 Test Setup ................................................................................................................................17 2.4.4 Test Result ...............................................................................................................................17 2.5 20dB Bandwidth .......................................................................................................................19 2.5.1 Test Requirement ....................................................................................................................19 2.5.2 Test Equipment........................................................................................................................19 2.5.3 Test Setup ................................................................................................................................19 2.5.4 Test Result ...............................................................................................................................19 Page 2 of 20

Report No.: SZ12120080E02 Change History Issue Date Reason for change 1.0 January 15, 2013 First edition 2.0 January 28, 2013 Second edition Page 3 of 20

Report No.: SZ12120080E02 1. GENERAL INFORMATION 1.1 EUT Description EUT Type ............................ WCDMA Digital Mobile Phone Serial No. ............................. (n.a, marked #1 by test site) Hardware Version ................ 212025 Software Version ................. N/A Applicant ............................. GUANGDONG OPPO MOBILE TELECOMMUNICATIONS CORP., LTD NO.18 HAIBIN ROAND, WUSHA, CHANG'AN, DONGGUAN, GUANGDONG, CHINA Manufacturer ....................... GUANGDONG OPPO MOBILE TELECOMMUNICATIONS CORP., LTD NO.18 HAIBIN ROAND, WUSHA, CHANG'AN, DONGGUAN, GUANGDONG, CHINA Frequency Band ................... 13.553MHz~13.567MHz Frequency ............................ 13.56MHz Channel Number.................. 1 Modulation Type.................. ASK Antenna Type ....................... Patch Antenna Antenna Gain ....................... 0 Power Supply ...................... Battery Brand Name: OPPO Model No.: SONY US465573H2 Serial No.: (n.a. marked #1 by test site) Capacitance: 2500mAh Rated Voltage: 3.7V Charge Limit: 4.35V Ancillary Equipment 1 ........ AC Adapter (Charger for Battery) Model Name: Slaconp (Shenzhen) Co., Ltd. Brand Name: SC0600PPA Serial No.: (n.a. marked #1 by test site) Rated Input: 100-240V, 200mA, 50/60Hz Rated Output: 5V, 1000mA Note 1: The EUT supports 13.56MHz NFC which was tested in this report. Note 2: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Page 4 of 20

Report No.: SZ12120080E02 1.2 Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart C: No. Identity Document Title 1 47 CFR Part 15 Radio Frequency Devices Test detailed items/section required by FCC rules and results are as below: No. Section Description Result 1 15.203 Antenna requirement PASS 2 15.207 Conducted Emission PASS 3 15.209 Radiated Emission PASS 15.225(a)(b)(c)(d) 4 15.225(e) Frequency Tolerance PASS 5 15.215(c) 20dB Bandwidth PASS NOTE: The tests were performed according to the method of measurements prescribed in ANSI C63.4 2010. Page 5 of 20

Report No.: SZ12120080E02 1.3 Facilities and Accreditations 1.3.1 Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at FL.1, Building A, FeiYang Science Park, Block 67, Bao An District, Shenzhen, 518055 P. R. China. The test site is constructed in conformance with the requirements of ANSI C63.4(2009) and CISPR Publication 22(2010); the FCC registration number is 695796. 1.3.2 Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Temperature (°C): 15 - 35 Relative Humidity (%): 30 -60 Atmospheric Pressure (kPa): 86-106 1.3.3 Measurement Uncertainty The uncertainty is calculated using the methods suggested in the "Guide to the Expression of Uncertainty in Measurement" (GUM) published by ISO. Uncertainty of Conducted Emission: ±1.8dB Uncertainty of Radiated Emission: ±3.1dB Page 6 of 20

Report No.: SZ12120080E02 2. 47 CFR PART 15C REQUIREMENTS 2.1 Antenna requirement 2.1.1 Applicable Standard According to FCC 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The EUT has a PCB printed antenna for NFC module. Please refer to EUT photos for more photos. Result: Compliant Page 7 of 20

Report No.: SZ12120080E02 2.2 Conducted Emission 2.2.1 Test Requirement According to FCC section 15.207, the radio frequency voltage that is conducted back onto the AC power line on any frequency within the band 150kHz to 30MHz shall not exceed the limits in the following table, as measured using a 50µH/50Ω line impedance stabilization network (LISN). Conducted Limit (dBµV) Frequency range (MHz) Quasi-peak Average 0.15 - 0.50 66 to 56 56 to 46 0.50 - 5 56 46 5 - 30 60 50 NOTE: a) The limit subjects to the Class B digital device. b) The lower limit shall apply at the band edges. c) The limit decreases linearly with the logarithm of the frequency in the range 0.15 - 0.50MHz. 2.2.2 Test Equipment Description Manufacturer Model Serial No. Cal. Date Cal. Due Receiver Narda PMM 9060 001WX11001 2012.11 2013.11 Receiver Narda PMM 9010 595WX11007 2012.11 2013.11 LISN Schwarzbeck NSLK 8127 812744 2012.05 2013.05 Pulse Limiter (20dB) Schwarzbeck VTSD 9561-D 9391 (n.a.) (n.a.) Page 8 of 20

Report No.: $Z12120080E02 2.2.3 Test Setup < 80cm > Pulse Limiter Receiver The EUT is placed on a 0.8m high insulating table, which stands on the grounded conducting floor, and keeps 0.4m away from the grounded conducting wall. The EUT is connected to the power mains through a LISN which provides 500/50uH of coupling impedance for the measuring instrument. The RF Card is used for the call between with the EUT, and the EUT was measured by transmitter mode continuously. A Pulse Limiter is used to protect the measuring instrument. The factors of the whole test system are calibrated to correct the reading. 2.2.4 Test Result The maximum conducted interference is searched using Peak (PK), Quasi—peak (QP) and Average (AV) detectors; Tests for both L phase and N phase lines of the power mains connected to the EUT are performed. Page 9 of 20

Report No.: SZ12120080E02 (Plot A: L Phase) (Plot B: N Phase) Result: PASS Page 10 of 20

Report No.: SZ12120080E02 2.3 Radiated Emission 2.3.1 Test Requirement A. Radiated Emission <30MHz (9KHz-30MHz, H-field) According to FCC section 15.225, for <30MHz, Radiated emissions were measured according to ANSIC63.4. The EUT was set to transmit at the highest output power. The EUT was set 30 meter away from the measuring antenna. The loop antenna was positioned 1 meter above the ground from the center of the loop. The measuring bandwidth was set to 10KHz. (Note: During testing the receive antenna was rotated about its axis to maximize the emission from the EUT) There was no detected Restricted bands and Radiated suprious emission below 30MHz. The 30m limit was converted to 3m Limit using square factor(x) as it was found by measurements as follows; 3 m Limit(dBuV/m) = 20log(X)+40log(30/3)= 20log(15848)+40log(30/3) = 124dBuV Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Field Strength@30m Field Strength@3m Frequency range (MHz) µV/m dBµV/m dBµV/m Below 13.110 30 29.5 69.5 13.110 ~ 13.410 106 40.5 80.5 13.410 ~ 13.553 334 50.5 90.5 13.553 ~13.567 15.848 84 124 13.567 ~ 13.710 334 50.5 90.5 13.710 ~14.010 106 40.5 80.5 Above 14.010 30 29.5 69.5 NOTE: a) Field Strength (dBµV/m) = 20*log[Field Strength (µV/m)]. b) In the emission tables above, the tighter limit applies at the band edges. B. Radiated Emission >30MHz (30MHz-1GHz, E-field) According to FCC section 15.205, the field strength of radiated emissions from intentional radiators at a distance of 3 meters shall not exceed the following values: Field Strength Frequency range (MHz) µV/m dBµV/m 30 - 88 100 40 88 - 216 150 43.5 216 - 960 200 46 Above 960 500 54 NOTE: Page 11 of 20

Report No.: SZ12120080E02 a) Field Strength (dBµV/m) = 20*log[Field Strength (µV/m)]. b) In the emission tables above, the tighter limit applies at the band edges. 2.3.2 Test Equipment Description Manufacturer Model Serial No. Cal. Date Cal. Due EMC Analyzer Agilent E7405A US44210471 2012.05 2013.05 Receiver Narda PMM 9060 001WX11001 2012.11 2013.11 Receiver Narda PMM 9010 595WX11007 2012.11 2013.11 Semi-Anechoic Albatross 9m*6m*6m (n.a.) 2012.05 2014.05 Chamber Test Antenna - Bi-Log Schwarzbeck VULB 9163 9163-274 2012.05 2013.05 Test Antenna - Horn Schwarzbeck BBHA 9120D 9120D-963 2012.05 2013.05 Test Antenna -Loop Schwarzbeck FMZB 1519 1519-022 2012.05 2013.05 T-Flash Card SanDisk 256MB (n.a.) (n.a.) (n.a.) 2.3.3 Test Setup 1) For radiated emissions from 9kHz to 30MHz Page 12 of 20

Report No.: SZ12120080E02 2) For radiated emissions from 30MHz to1GHz 3) For radiated emissions above 1GHz The test is performed in a 3m Semi-Anechoic Chamber; the antenna factor, cable loss and so on of the site (factors) is calculated to correct the reading. The EUT is placed on a 0.8m high insulating Turn Table, and keeps 3m away from the Test Antenna, which is mounted on a variable-height antenna master tower. Page 13 of 20

Report No.: SZ12120080E02 For the test Antenna: 1) In the frequency range of 9KHz to 30MHz, magnetic field is measured with Loop Test Antenna. The Test Antenna is positioned with its plane vertical at 1m distance from the EUT. The center of the Loop Test Antenna is 1m above the ground. During the measurement the Loop Test Antenna rotates about its vertical axis for maximum response at each azimuth about the EUT. 2) In the frequency range above 30MHz, Bi-Log Test Antenna (30MHz to 1GHz) and Horn Test Antenna (above 1GHz) are used. Test Antenna is 3m away from the EUT. Test Antenna height is varied from 1m to 4m above the ground to determine the maximum value of the field strength. The emission levels at both horizontal and vertical polarizations should be tested. 2.3.4 Test Result 2.3.4.1 Radiated Emission <30MHz (9KHz-30MHz, H-field) A. Test Plots 2.3.4.2 Radiated Emission >30MHz (30MHz-1GHz, E-field) A. Test Plots: Page 14 of 20

Report No.: SZ12120080E02 (Plot A: Test Antenna Vertical) NO. Fre. Pk QP AV Limit- Limit- Limit- Antenna Verdict (MHz) PK QP AV 1 431.546 36.78 N.A N.A N.A 46.0 N.A Vertical PASS (Plot B: Test Antenna Horizontal) Page 15 of 20

Report No.: SZ12120080E02 NO. Fre. Pk QP AV Limit- Limit- Limit- Antenna Verdict (MHz) PK QP AV 1 363.815 36.98 N.A N.A N.A 46.0 N.A Horizontal PASS Result: PASS Page 16 of 20

Report No.: SZ12120080E02 2.4 Frequency Tolerance 2.4.1 Test Requirement According to FCC section 15.225, the devices operating in the 13.553~13.567 MHz shall maintain the carrier frequency within 0.01% of the operating frequency over the temperature variation of -20°C to +50°C using an environmental chamber. The primary supply voltage is varied from 85% to 115% of the voltage normally at the input to the device or at the power supply terminals if cables are not normally supplied. 2.4.2 Test Equipment Description Manufacturer Model Serial No. Cal. Date Cal. Due Spectrum Analyzer Agilent E7405A US44210471 2012.05 2013.05 DC Power Supply Good Will GPS-3030DD EF920938 2012.05 2013.05 YinHe Temperature Chamber Experimental HL4003T (n.a.) 2012.05 2013.05 Equip. Spectrum Analyzer Agilent E7405A US44210471 2012.05 2013.05 2.4.3 Test Setup Temperature Chamber EUT DC Power Supply The EUT, which is powered by the DC Power Supply directly, is located in the Temperature Chamber. The EUT was measured by transmitter mode continuously. 2.4.4 Test Result Operating Frequency: 13,560,000 Hz Deference Voltage: 3.7V Deviant Limit: ±0.01% Page 17 of 20

Report No.: SZ12120080E02 Test Conditions VOLTAGE Power Temperature Frequency(Hz) Deviation(%) Verdict (%) (VDC) (°C) 100 +20°C(Ref) 13,560,305 +0.002249 100 -20 13,559,685 -0.002323 100 -10 13,559,677 -0.002382 100 0 13,559,652 -0.002566 100 +10 13,559,614 -0.002847 3.7 100 +20 13,559,562 -0.003230 100 +25 13,559,553 -0.003297 PASS 100 +30 13,559,544 -0.003363 100 +40 13,559,551 -0.003311 100 +50 13,560,579 +0.004270 Battery End 3.6 +20 13,559,571 -0.003164 Point 115 4.2 +20 13,559,592 -0.003009 Page 18 of 20

Report No.: SZ12120080E02 2.5 20dB Bandwidth 2.5.1 Test Requirement According to FCC section 15.215(c), the 20dB bandwidth should be contained within the frequency band designated in the rule section under which the EUT is operated, it was measured with a spectrum analyzer connected the EUT while the EUT is operating in transmission mode. 2.5.2 Test Equipment Description Manufacturer Model Serial No. Cal. Date Cal. Due Spectrum Analyzer Agilent E7405A US44210471 2012.05 2013.05 DC Power Supply Good Will GPS-3030DD EF920938 2012.05 2013.05 2.5.3 Test Setup Spectrum Analyzer EUT 2.5.4 Test Result Measurement Limit Centre 20dB Bandwidth Frequency Range 20dB Frequency Range Verdict Frequency (KHz) (MHz) Bandwidth(KHz) (MHz) 13.56MHz 12.5521 13.55371~13.56626 14 13.553~13.567 Pass Please refer to the following plot. Page 19 of 20

Report No.: SZ12120080E02 ** END OF REPORT ** Page 20 of 20


Document Created: 2019-09-05 02:56:39
Document Modified: 2019-09-05 02:56:39
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC