COMOSAR E-Field Probe Calibration Report - 6G

FCC ID: R9C-X9006

RF Exposure Info

Download: PDF
FCCID_2238303

(((. SATIMO Tre microwavevsioncompany " COMOSAR E—Field Probe Calibration Report Ref : ACR.269.1.13.SATU.A SHENZHEN MORLAB COMMUNICATIONS TECHNOLOGY CO., LTD FL3, BUILDING A, FEIYANG SCIENCE PARK, NO.8 LONGCHANG ROAD, BLOCK 67, BAOAN DISTRICT, SHENZHEN, GUANGDONG PROVINCE, P.R. CHINA SATIMO COMOSAR DOSIMETRIC E—FIELD PROBE SERIAL NO.: SN 27/13 EPG193 Calibrated at SATIMO US 2105 Barrett Park Dr. — Kennesaw, GA 30144 *a |ACCR!DI‘TID Caibraion Cent szzu t 09/25/2013 Summary: This document presents the method and results from an accredited COMOSAR Dosimetric E—Field Probe calibration performed in SATIMO USA using the CALISAR / CALIBAIR test bench, for use with a SATIMO COMOSAR system only. All calibration results are traceable to national metrologyinstitutions

COMOSAR E—FIELD PROBE CALIBRATION REPORT Ref: ACR.269.1.13.SATUA sfifim\o Name Function Date Signature Prepared by : Jérome LUC Product Manager |9/26/2013 Checked by: Jérome LUC Product Manager 9/26/2013 Approved by : Kim RUTKOWSKI Quality Manager 9/26/2013 hus Customer Name Shenzhen Morlab Distribution : Communications istribution : Technology Co., Ltd Issue Date Modifications A 9/26/2013 Initial release Page: 29 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO: The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be releasedin whole orpart without written approval ofSATIMO,

((L. \ COMOSAR E—FIELD PROBE CALIBRATION REPORT Ref: ACR.269.1.13.8ATUA TABLE OF CONTENTS 1 Devi@ UNG@F TESt ... 2 Product DeSCriptiOn ...« 2.1 General Information 4 3+ MEBSUIRI@NEM@TROU .... is ceusmmmunccnmennnmeineinciormeetieciieeccosteceentifrrreccieprnntecreprnirase 4 3.1 Linearity 4 3.2 Sensitivity 5 3.3 Lower Detection Limit 5 3.4 Isotropy 5 3.5 Boundary Effect 5 4 MEASUTCMENEUNCETIAIMEY..............sssicsnssoncccmnmmmmmnmmmmmnnnnmmnmnnnnmnnnnnnnnnnmmnnmnmmm 5 5. CaliDAtiOM MCASUT@MNE RESUIS................cssns0000000ee000000mneemmmenrmemmrvnnnnmmnenennmnmnence 6 5.1 Sensitivity in air 6 5.2 Linearity 7 5.3 Sensitivity in liquid 7 5.4 Isotropy 8 6 Li8t OF EQMIDMENE.........ccuossecrmcomemttinrmitentecasiitiserinstenienitineristenntemsernmnersitineee 9 Page: 39 This document shall not be reproduced, except infull or inpart, without the written approval ofSATIMO The information contained herein is to be usedonsfor thepurposefor which it is submiteedand is not to be released in whole or part without written approval ofSATO:

{t . \ COMOSAR E—FIELD PROBE CALIBRATION REPORT Ref: ACR.200.1 12. 8ATULA SATIMO 1 DEVICE UNDER TEST Device Under Test Device Type COMOSAR DOSIMETRIC E FIELD PROBE Manufacturer Satimo Model SSE2 Serial Number SN 27/13 EPG193 Product Condition (new / used) New Frequency Range of Probe 0.7 GHz—6GHz Resistance of Three Dipoles at Connector Dipole 1: R1=0.205 MQ Dipole 2: R2=0.176 MQ Dipole 3: R3—0.214 MQ A yearly calibration interval is recommended. 2 PRODUCT DESCRIPTION 2.1 GENERAL INFORMATION Satimo‘s COMOSAR E field Probes are built in accordance to the IEEE 1528, OET 65 Bulletin C and CEV/IEC 62209 standards. Figure 1 —Satimo COMOSAR Dosimetric Efield Dipole Probe Length 330 mm Length of Individual Dipoles 2 mm Maximum external diameter 8 mm Probe Tip External Diameter 2.5 mm Distance between dipoles / probe extremity 1 mm 3 MEASUREMENT METHOD The IEEE 1528, OET 65 Bulletin C, CENELEC ENS0361 and CEI/IEC 62209 standards provide recommended practices for the probe calibrations, including the performance characteristics of interest and methods by which to assess their affect. All calibrations / measurements performed meet the fore mentioned standards. 3.1 LINEARITY The evaluation of the linearity was done in free space using the waveguide, performing a power sweep to cover the SAR range 0.01W/kg to 100W/kg. Page: 49 This document shall not be reproduced, except infull or in part, withoutthe writen approval ofSATIMO: The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be releasedin whole orpart without written approval ofSATIMO.

((l. \ COMOSAR E—FIELD PROBE CALIBRATION REPORT Ref: ACR 269.1.13 SATU A SATIMO 3.2 SENSMVITY The sensitivity factors of the three dipoles were determined using a two step calibration method (air and tissue simulating liquid) using waveguides as outlined in the standards. 3.3 LOWER DETECTION LIMIT The lower detection limit was assessed using the same measurement set up as used for the linearity measurement. The required lower detection limit is 10 mW/kg. 3.4 ISOTROPY The axial isotropy was evaluated by exposing the probe to a reference wave from a standard dipole with the dipole mounted under the flat phantom in the test configuration suggested for system validations and checks. The probe was rotated along its main axis from 0 — 360 degrees in 15 degree steps. The hemispherical isotropy is determined by inserting the probe in a thin plastic box filled with tissue—equivalentliquid, with the plastic box illuminated with the fields from a half wave dipole. The dipole is rotated about its axis (0°%—180°) in 15° increments. At each step the probe is rotated about its axis (0%—360°). 3.5 BOUNDARY EFFECT The boundary effect is defined as the deviation between the SAR measured data and the expected exponential decay in the liquid when the probe is oriented normal to the interface. To evaluate this effect, the liquid filled flat phantom is exposed to fields from either a reference dipole or waveguide. With the probe normal to the phantom surface, the peak spatial average SAR is measured and compared to the analytical value at the surface. 4 MEASUREMENT UNCERTAINTY The guidelines outlined in the IEEE 1528, OET 65 Bulletin C, CENELEC EN50361 and CEVIEC 62209 standards were followed to generate the measurement uncertainty associated with an E—field probe calibration using the waveguide technique. All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95%confidence level using a coverage factor of k=2,traceable to the InternationallyAccepted Guides to Measurement Uncertainty. Uncertainty analysis ofthe probe calibration in waveguide Uncertainty Probability e 5 Standard ERROR SOURCES value (%) Distribution DW!9" * Uncertainty (%) Incident or forward power 3.00% Rectangular \/5 | 1 1.732% Reflected power 3.00% Rectangular [ | 1 1.732% Liquid conductivity 5.00% Rectangular [3 | 1 2.887% Liquid permittivity 4,00% Rectangular [3 | 1 2309% Field homogeneity 3.00% Rectangular ‘/5 ’ 1 1.732% Field probe positioning 5,00% Rectangular \/_'; | 1 2.887% Field probe linearity 3.00% Rectangular M | 1 1.732% Page: 59 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO: The informationcontainedherein is to be used ons for the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO

({I : \ COMOSAR E—FIELD PROBE CALIBRATION REPORT Ref: ACR 269.1.13.SATUA SATIMo Combined standard uncertainty 5.831% Expanded uncertainty . 95 % confidence level k = 2 12.0% 5 CALIBRATION MEASUREMENT RESULTS Calibration Parameters Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % 5.1 SENSITIVITY IN Normx dipole Normy dipole Normz dipol,e 1 (wV/(V/im))| 2 (wV/(V/im))| 3 (V/(V/m)) 0.50 0.55 0.52 DCP dipole 1 DCP dipole 2 DCP dipole 3 (mV) (mV) (mV) 90 101 99 Calibration curves ei=f(V) (i=1,2,3) allow to obtain H—field value using the formula: Calibration curves 1003— § E—Field (VAn) Dipole 1 § Dgole 2 8 § 4. 0&] ooe oor oo o8 ot0 of2 on 016 0;8 Votage (V) Page: 69 This document shall not be reproduced, except inill or i part, without the written approval of$ATIMO, The information contained herem is to be used onlyfor the purposefor which it is submitied and is not to be releasedin whole orpart without written approval of SATIMO.

(( n d COMOSAR E—FIELD PROBE CALIBRATION REPORT Ref: ACR 269.1.13.SATUA SATIN/ID 5.2 LINEARITY Linearity 1.00— 076— 050 Lined ity Ertor (0B) 025 0 90 fRitnbaed nlbe} fnd $ 1% 050 q75— 1.00— 0 100 200 300 400 5oo 600 700 s E—Field (V/m) Linea I+/1.54% (+/0 074B 5.3 SENSITIVITY IN LIQUID Liquid Frequency Permittivity Epsilon (S/m) ConvE {MHz 100MHz HLS200 5200 36.11 4.81 23.71 BLS200 5200 49.87 4.99 2439 HLS400 5400 36.61 5.08 26.58 BLS400 5400 49.09 5.64 27.58 HLS600 5600 35.97 5.37 25.33 BLS600 5600 48.64 5.99 26.30 HLS800 5800 35.33 5.59 25.64 BLS800 5800 47.76 6.21 26.47 LOWER DETECTION LIMIT: 7mW/kg Page: 79 This document shall not be reproduced, except infull or in part, without the writeen approval ofSATIMO The information contained herein is to be used onlfor the purposefor which it is submitted andis not to be releasedin whole orpart without written approval ofSATIMO.

(( es \ COMOSAR E—FIELD PROBE CALIBRATION REPORT Ref: ACR269 1. 13 8ATUA SATIMo 5.4 ISOTROPY HL5400 MHz — Axial isotropy: 0.08 dB — Hemisphericalisotropy: 0.13 dB issh 4 & & t d incammemien‘t. Page: 89 This document shall not be reproduced, evcept infull or in part, without the written approval ofSATIMO The information contained herein is to be used onlyfor the purposefor which it is submittedand is not to be released in whole orpart without written approval ofSATIMO:

COMOSAR E—FIELD PROBE CALIBRATION REPORT Ref: ACR.269.1 13 SATUA 6 LIST OF EQUIPMENT Equipment Summary Sheet Equipment Manufacturer / i nhan Current Next Calibration Description Model |‘"%""**0990 M9—/ Copprofion Date Date Fiat Phantom Satimo SN—20/08—SAM71 Validated. No cal Fequired. Validated required. No cal COMOSAR Test Bench Version 3 NA Validated. Fequired. No cal Validated required. No cal Network Analyzer RNOG®&SChware g400132 o2ro13 o2ro16 i Characterized prior to |Characterized prior to Reference Probe Setima EP 94 SN 37/08 test. No calrequired. [test. No cal required. Multimeter Keithley 2000 1188656 1172010 1172013 Signal Generator Agilent E4438C MY49070581 1212010 1222013 i Characterized prior to |Characterized prior to Amplifier Asthercomin SN 046 test. No calrequired. [test. No cal required Power Meter HP E4418A US38261498 1172010 1172013 Power Sensor HP ECP—E26A US37181460 1172010 1172013 us Characterized prior to |Characterized prior to prectionsi couple Neadsit=0 1908 test._ No cal required. |test._ No cal required. . . Validated. No cal Validated. No cal Waveguide Mega Industries 069Y7—158—13—712 hlrag. Fequired. . m . Validated. No cal Validated. No cal Waveguide Transition Mega Industries O69Y7—158—13—701 fequired. Fequired. . ww . Validated. No cal Validated. No cal |Waveguide Termination| Mega Industries O69Y7—158—13—701 required required. [Temperature / Humidity Sensor Control Company 11—661—9 32012 372014 Page: 9.9 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO: The information containedhereim is to be used onlyfor the purposefor which it is submitted and is not to be releasedin whole orpart without written approval ofSATMO,


Document Created: 2019-08-31 09:51:55
Document Modified: 2019-08-31 09:51:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC