Dipole 1900MHz Calibration Report

FCC ID: R9C-R831L

RF Exposure Info

Download: PDF
FCCID_2298741

(/r.\ SATIMO Te micrmare visoncompany .A SAR Reference Dipole Calibration Report Ref: ACR.269.4.13.SATU.A SHENZHEN MORLAB COMMUNICATIONS TECHNOLOGY CO., LTD FL3, BUILDING A, FEIYANG SCIENCE PARK, NO.8 LONGCHANG ROAD, BLOCK 67, BAOAN DISTRICT, SHENZHEN, GUANGDONG PROVINCE, P.R. CHINA SATIMO COMOSAR REFERENCE DIPOLE FREQUENCY: 1900 MHZ SERIAL NO.: SN 30/13 DIP1G900—261 Calibrated at SATIMO US 2105 Barrett Park Dr. — Kennesaw, GA 30144 Caltrasion CERT w22402 09/25/2013 Summary: This documentpresents the method and results from an accredited SAR reference dipole calibration performed in SATIMO USA using the COMOSAR test bench. All calibration results are traceable tonational metrology institutions

((4. sarimo a SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 269.4.13.SATU A Name Function Date Signature Prepared by : Jérome LUC Product Manager 9/26/2013 fi’ Checked by : Jérome LUC Product Manager 9/26/2013 fi’ Approved by : Kim RUTKOWSKI Quality Manager 9/26/2013 ... mathoti? Customer Name Shenzhen Morlab . us Communications Distribution : Technology Co., Ltd Issue Date Modifications A 9/26/2013 Initial release Page: 210 This document shall not be reproduced, except infull oin part, without the writen approval ofSATTMO The information contained hereini to be used onlyfor the purposefor which it is submitted and is not to be releasedin whole orpart without written approval ofS1TIMO.

(t. \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.2694.13.SATUA SATIMO TABLE OF CONTENTS 1 IMfOUUONON: u.cs mumtenemanncennumnneeuansununtendencrnemunnsecemen ce 2 D@ViC@ UMG@T TESt........ccssssssssccnnnnmmmmnnnmmmmmmmnnnnmnnnnnnmnnnnmnnnnnnnnnnnnenemnmsnnnmmnmmmn 4 3 PIOOUCHD@SETIPHGH ... . :s i. rmmmucms h crmncoenieetionemerrosriiensremateomerrenreeerneecenteivees 4 3.1 General Information 4 & MEASUIETI@NEMOIAOU ...:::,.....—sssmmssssscemcsmmmimmmmimnsnemmmnminanimimnemiiien B 4.1 Return Loss Requirements $ 4.2 Mechanical Requirements 5 3 MEASUIRiRi@RE UNICEAIANINY ....:.:—mmurenesncammmeiiicaiteientaraiercectetee 5.1 Return Loss 5 5.2 Dimension Measurement 5 5.3 Validation Measurement 5 6. CalibAtiON MCASUTEMENE RESUIS...............sssmmssnmmemnnmmmmmmmnnnmmmmmnnnnnmmmnnsnmmmmmmms 6 6.1 Return Loss 6.2 Mechanical Dimensions 6 L. NAHORHION IERSUERMIENLE . is s. iss srccomrsrmmmcmmmmmmemmmmnstimrrretiinmmnssitonmmmnsscemseresticseth 7 7.1 Measurement Condition 7 7.2 Head Liquid Measurement 7 7.3 Measurement Result 8 7.4 Body Measurement Result 9 $ LMSFOBRQUIPMENL .....Ssommummmmencemmenememmeannrnsinmemtnretenreisentiieacacters 10 Page: 310 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor thepurposefor which it is submittedand is not to be released in whole orpart without written approval ofSATTMO.

{{ L: SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 269.4.13.SATU A 1 INTRODUCTION This document contains a summary of the requirements set forth by the IEEE 1528, OET 65 Bulletin C and CEV/IEC 62209 standards for reference dipoles used for SAR measurement system validations and the measurements that were performed to verify that the product complies with the fore mentioned standards. 2 DEVICE UNDER TEST Device Under Test Device Type COMOSAR 1900 MHz REFERENCE DIPOLE Manufacturer Satimo Model $1D1900 Serial Number SN 30/13 DIP1G900—261 Product Condition (new / used) New A yearly calibration interval is recommended. 3 PRODUCT DESCRIPTION 3.1 GENERAL INFORMATION Satimo‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, OET 65 Bulletin C and CEU/IEC 62209 standards. The product is designed for use with the COMOSAR test bench only. F Figure 1 —Satimo COMOSAR Validation Dipole Page: 410 This document shall not be reproduced, except infull or in part, without the writen approval ofSATIMO. The information containedherein is to be used onlyfor the purposefor which it is submitted andis not to be released in whole or part without written approval ofSATTMO.

{f Ls SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 269 4.13 SATU A 4 MEASUREMENT METHOD The IEEE 1528, OET 65 Bulletin C and CEV/IEC 62209 standards provide requirements for reference dipoles used for system validation measurements. The following measurements were performed to verify that the product complies with the fore mentioned standards. 4.1 RETURN LOSS REQUIREMENTS The dipole used for SAR system validation measurements and checks must have a return loss of —20 dB or better. The return loss measurement shall be performed against a liquid filled flat phantom, with the phantom constucted as outlined in the fore mentioned standards. 4.2 MECHANICAL REQUIREMENTS The IEEE Std. 1528 and CEVIEC 62209 standards specify the mechanical components and dimensions of the validation dipoles, with the dimensions frequency and phantom shell thickness dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2 mm phantom shell thickness. 5 MEASUREMENT UNCERTAINTY All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2, traceable to the Internationally Accepted Guides to Measurement Uncertainty. 5.1 RETURNLOSS The following uncertainties apply to the return loss measurement: Frequency band Expanded Uncertainty on Return Loss 400—6000MHz 0.1 dB 5.2 DIMENSION MEASUREMENT The following uncertainties apply to the dimension measurements: Length (mm) Expanded Uncertainty on Length 3 —300 0.05 mm 5.3 VALIDATION MEASUREMENT The guidelines outlined in the IEEE 1528, OET 65 Bulletin C, CENELEC ENS0361 and CEMIEC 62209 standards were followed to generate the measurement uncertainty for validation measurements. Scan Volume Expanded Uncertainty 3 20.3 % 10 g 20.1 % Page: 510 This document shall not be reproduced, except infull or in part, without the writeen approval ofSATIMO The information contained hereinis to be used only for thepurposefor which it is submittedandis not to be releasedin whole or part without writeenapproval ofSATIMO

SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 269.4.13.SATUA 6 CALIBRATION MEASUREMENT RESULTS 6.1 RETURNLOSS Frequency, MR Frequency (MHz) Return Loss (dB) Requirement (dB) 1900 —26.71 —20 6.2 MECHANICAL DIMENSIONS Frequency MH2 L. mm hmm d mm required measured required measured required measured 300 420.0 £1%. 250.0 +1 % 635 41 %. aso 290.0 +1 % 166.7 +1 % 635 41 %. 750 176.0 +1 % 100.0 +1 % 6.35 +1 %. s35 161.0£1% s9.8 +1% 3611% 200 149.0 +1 %. 83.3+1% 36+1% 1450 8o.1 +1 % 51.7+41% 36+1% 1500 80.5 +1 % 50.0 +1 %. 3611% 1640 79.0£1% 457 +1% 3611% 1750 752i1% 42.9 +1%. 36+1% 1800 72.0 +1 % 41.7 +1 %. 3.611% 1900 68.0 +1 % Pass 39.5 +1 %. PASS 1621% PaS$ 1950 66.3 +1% 3a.5 +1 %. 26:1% 2000 64.5 41 % 37.5 +1% 16+1% 2100 610 +1% 35.741% 16+:1% 2300 55.5 11 % 32641% 3611% 2450 515 41% 30.4 +1% 1611% 2600 a8.5 £1%. 20.8 +1% 36+1% 3000 ans +1% 25.0 +1% 36+1% 3500 37.041% 264 +1% 36+1% 3700 34.741% 26.4 +1 %. 1611% Page: 610 This documenshall not be reproduced, exceptin full or in part, withoutthe writen approval of SATIMO The information contained herein is to be used only for thepurposefor whichit is submited and is not to be releasedin whole or part without written approval of ATIMO

(( Ls SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 269.4.13 SATU A 7 VALIDATION MEASUREMENT The IEEE Std. 1528, OET 65 Bulletin C and CEVIEC 62209 standards state that the system validation measurements must be performed using a reference dipole meeting the fore mentioned return loss and mechanical dimension requirements. The validation measurement must be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. Per the standards, the dipole shall be positioned below the bottom of the phantom, with the dipole length centered and parallel to the longest dimension of the flat phantom, with the top surface ofthe dipole at the described distance from the bottom surface of the phantom. 7.1 MEASUREMENT CONDITION Software OPENSAR V4 Phantom SN 20/09 SAM71 Probe SN 18/11 EPG122 Liguid Head Liguid Values: eps‘ : 39.8 sigma 1.43 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=8mm/dy—=§mm Zoon Scan Resolution dx=8mm/dy—=§m/dz=Smm Frequency 1900 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % 7.2 HEAD LIQUID MEASUREMENT ""Tg" Relative permittivity (e,‘) Conductivity (0) $/m required measured required measured 300 45.3 45 % 0.87 15 % 450 43.5 15 % 0.87 25 % 750 41945 % 0.89 +5 % 835 41.5 25 % 0.90 15 % 900 41.5 45 % 0.97 15 % 1450 40.5 15 % 1.20 45 % 1500 40.4 25 % 12345% 1640 40.2 45 % 13145 % 1750 40.1 25 % 13745 % 1800 40.0 45 % 1.40 45 % 1900 40.0 25 % PASS 1.40 15 % PASS 1950 40.0 15 % 1.40 15 % 2000 40.0 25 % 1.40 45 % 2100 39.8 15 % 149 15 % 2300 39.5 15 % 167 45% 2450 39.245 % 1.80 25 % 2600 39.0 15 % 19615 % 3000 38.5 45 % 2.40 15 % 3500 37.945% 29145 % Page: 710 This document shall not he reproduced, except inul or in part, without the writen approval ofSATTMO The information contained herein is to be used onlyfor thepurposefor which it is submittedand is not to be releasedin whole or part without written approval ofSATIMO

{f (. \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.2694.13 SATU A 7.3 MEASUREMENT RESULT The 1E Std. 1528 and CEVIEC 62209 standards state that the system validation measurements should produce the SAR values shown below (for phantom thickness of 2 mm), within the uncertainty for the system validation All SAR values are normalized to 1 W forward power. In bracket, the measured SAR is given with the used input power inrminl 1 8 san (w/ke/w) 10 g sar (w/ke/w) required measured required measured 300 2.85 1.94 450 458 3.06 750 8.49 5.55 835 956 6.22 900 10.9 6.99 1450 29 16 1500 30.5 16.8 1640 34.2 18.4 1750 36.4 193 1800 38.4 20.1 1900 39.7 39.39 (3.94) 20.5 20.07 (2.01) 1950 40.5 20.9 2000 411 211 2100 43.6 21.9 2300 48.7 233 2450 524 24 2600 55.3 24.6 3000 63.8 25.7 3500 671 25 \‘ UR Page: 810 This document shall not be reproduced, except in full or in part, without the writen approval of ATIMO Theinformation contained herein is to heused onlfor the purposefor whichit is submitted andis not to be released in whole or part without written approval of S1TDIO

(¢e. M SAR REFERENCE DIPOLE CALIBRATION REPORT Ref. ACR.269.4.13.SATUA SATIMO 7.4 BODY MEASUREMENT RESULT Software OPENSAR V4 Phantom SN 20/09 SAMT7I Probe SN 18711 EPG122 Liquid BodyLiquid Values: eps‘ 52.5 sigma: 1.50 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8m/dz=—Smm Frequency 1900 MHz Inputpower 20 dBm Liquid Temperature 21 °C Lab Temperature 21°C Lab Humidity 45% F ";':"1““ 1 g sant (w/kg/w) 10 g SAR (W/kg/w) measured measured 1900 42.33 (4.23) 22.27 (2.23) \' UA — Page 9710 This document shall not be reproduced, exceptinfull or in part, without the writen approval of ATIMO Theinformation contained herein is to be used only for the purpose for which i is submitied and is not to be released in whole or part without written approval of SATTMO

SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 269.4.13.SATU A Equipment Manufacturer / Current Next Calibration Description Modet [180006¢2000 NO—] Copiprotion Date Date Validated. No cal Validated. No call SAM Phantom Satimo SN—20/08—SAM71 Fequired. required. Validated. No cal Validated No call COMOSAR Test Bench Version 3 NA Fequired required Network Analyzer RN°C®;vi""wm sN100132 o2r013 o2r016 Calipers Carrera CALIPER—01 1212010 1222013 Characterized prior to |Characterized prior to Reference Probe Satimo EPG122 SN 18711 test. No calrequired. |test. No cal required Multimeter Keithley 2000 1188656 1172010 112013 Signal Generator Agilent E4438C MY49070581 1272010 1212013 . Characterized prior to |Characterized prior to Amplifier Asthercomm sn 046 test. No cal required. |test. No cal required. Power Meter HP E4418A US38261498 1172010 112013 Power Sensor HP ECP—E26A US37181460 1172010 1172013 iands Characterized prior to |Characterized prior to Directional Coupler Narda 4216—20 01386 test. No cal required. [test.. No cal required. Temperature and Humidity Sensor Control Company 11—661—9 32012 312014 Page: 10/10 This document shall not be reproduced, except infull or in part, without the writeen approval ofSATIMO: The information containedherein is to be used onlyforthe purposefor which it is submitted andis not to be releasedin whole orpart without written approval ofSATIMO.


Document Created: 2019-08-31 09:48:56
Document Modified: 2019-08-31 09:48:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC