SAR Report-7

FCC ID: R9C-R8006

RF Exposure Info

Download: PDF
FCCID_2237811

((. SATIMO The micrmare vision conpany..~ SAR Reference Dipole Calibration Report Ref: ACR.269.3.13.SATU.A SHENZHEN MORLAB COMMUNICATIONS TECHNOLOGY CO., LTD FL3, BUILDING A, FEIYANG SCIENCE PARK, NO.8 LONGCHANG ROAD, BLOCK 67, BAOAN DISTRICT, SHENZHEN, GUANGDONG PROVINCE, P.R. CHINA SATIMO COMOSAR REFERENCE DIPOLE FREQUENCY: 1750 MHZ SERIAL NO.: SN 30/13 DIP1G750—260 Calibrated at SATIMO US 2105 Barrett Park Dr. — Kennesaw, GA 30144 «n ACCREDITED Calbanion CHAT eazue in 09/25/2013 Summary: This document presents the method and results from an accredited SAR reference dipole calibration performed in SATIMO USA using the COMOSAR test bench. All calibration results are traceable to national metrology institutions

(L.. \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 260.3.13.SATU.A BC-\TIN’ID Name Function Date Signature Prepared by : Jérome LUC Product Manager 9/26/2013 fi Checked by : Jérome LUC Product Manager |9/26/2013 fi/ Approved by: Kim RUTKOWSKT Quality Manager 9/26/2013 j..,, mathoush Customer Name Shenzhen Morlab ; Communications Distribution: Technology Co., Ltd Issue Date Modifications A 9/26/2013 Initial release Page: 2710 This document shall not be reprodced, except infull or in part, without the written approval ofSATIMO The information containedherein i to be used onlyfor the purposefor which it is submitted and is not to be releasedin whole orpart without written approval ofSATDAO,

(6. \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.260.3.13 SATU A SKI'IN,ID TABLE OF CONTENTS 1. TMEEOUUOHON::smmmemsmemmrnicreynniiiitneeiteOittercemsverremmsemsnmmmmessnstmmeisriescereee 4 2. D@ViC@ UMG@T TSb ...........csssssssmmmmmmmmmmmmmmmmnnnmnmmnsernnnmmmmmemmmssmmmmmmnmnnmmmmncen 4 3 PFOGUCKDESCHIPHON ... : omm merman efincermmnmunntemiientennrmitiremmetstteatiie in en 3.1 General Information 4 4 Measurement MethOG ..................slllllll> 4.1 Return Loss Requirements 3 4.2 Mechanical Requirements 5 3. MEBSUT@MNE UNC@TIIIEY ..................csnnnmeemmmmemnecenmmenreemmmmmnmeenmmmnssenmmmmsenmmme $ 5.1 Return Loss 5 5.2 Dimension Measurement 5.3 Validation Measurement 5 6 CalibAtiOM MCASUT@MENE RESUIS..............ssssmssssmmmmmmeccnnmmmnnnnmmmmnnnnmmmnmmnmmnn 6 6.1 Return Loss 6.2 Mechanical Dimensions o 7 Validation measurement... ............................................................................. mtead 7.1 Measurement Condition sbow 7.2 Head Liquid Measurement 7.3 Measurement Result se 7.4 Body Measurement Result w § LISEOFEQUIPMIGHE ... smm ommmmmumaniimmennnmmemetars Page: 3710 This document shall not be reproduced, except infull or in part, without the writien approval ofSATIMO The informationcontained hereim is to be used onlyfor thepurposefor which it is submittedandis not to be released in whole orpart without written approval ofSATDO,

({ des \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACK.2693.13.SNTUA 1 INTRODUCTION This document contains a summary of the requirements set forth by the IEEE 1528, OET 65 Bulletin C and CEV/IEC 62209 standards for reference dipoles used for SAR measurement system validations and the measurements that were performed to verify that the product complies with the fore mentioned standards. 2 DEVICE UNDER TEST Device Under Test Device Type COMOSAR 1750 MHz REFERENCE DIPOLE Manufacturer Satimo Model SID1750 Serial Number SN 30/13 DIP1G750—260 Product Condition (new / used) New A yearly calibration interval is recommended. 3 PRODUCT DESCRIPTION 3.1 GENERAL INFORMATION Satimo‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, OET 65 Bulletin C and CEUIEC 62209 standards. The product is designed for use with the COMOSAR test bench only pmmpminge~ Figure 1 — Satimo COMOSAR Validation Dipole Page: 410 This document shall not be reproduced, except infull or in part, without the written approval ofSATDO The information containedherein is to be usedonlyfor the purpose for which it is submitied and is not to be released in whole or part without written approval ofSTIO

((l s SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 269 3.13 SATU A 4 MEASUREMENT METHOD The IEEE 1528, OET 65 Bulletin C and CEI/IEC 62209 standards provide requirements for reference dipoles used for system validation measurements. The following measurements were performed to verify that the product complies with the fore mentioned standards. 4.1 RETURNLOSS REQUIREMENTS The dipole used for SAR system validation measurements and checks must have a return loss of—20 dB or better. The return loss measurement shall be performed against a liquid filled flat phantom, with the phantom constucted as outlined in the fore mentioned standards. 4.2 MECHANICAL REQUIREMENTS The IEEE Std. 1528 and CEVIEC 62209 standards specify the mechanical components and dimensions of the validation dipoles, with the dimensions frequency and phantom shell thickness dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2 mm phantom shell thickness. S MEASUREMENT UNCERTAINTY All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2, traceable to the Internationally Accepted Guides to Measurement Uncertainty. 5.1 RETURNLOSS The following uncertainties apply to the return loss measurement: Frequency band Expanded Uncertainty on Return Loss 400—6000MHz 0.1 dB 5.2 DIMENSION MEASUREMENT The following uncertainties apply to the dimension measurements: Length (mm) Expanded Uncertainty on Length 3 — 300 0.05 mm 5.3 VALIDATION MEASUREMENT The guidelines outlined in the IEEE 1528, OET 65 Bulletin C, CENELEC ENS0361 and CEVIEC 62209 standards were followed to generate the measurement uncertainty for validation measurements. Scan Volume Expanded Uncertainty Ig 20.3 % 10 g 20.1 % Page: 510 This document shall not be reproduced, except infull oin part, without the writeenapproval ofSATIMO The information containedherein is to be used onlyfor the purposefor which it is submitted andis not to be releasedin whole orpart without written approval ofSATIMO

((; + SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: AUK.209.3.13.SATUA SATIMO 6 CALIBRATION MEA IREMENT RESULTS 6.1 RETURNLOSS Frequency (MHz) Return Loss (dB) Requirement (dB) 1750 —22.80 —20 6.2 MECHANICAL DIMENSIONS Frequency MHz L. mm h mm dmm required measured required measured required measured 300 420.0+1%. 250.0 +1 % 635 41% aso 290.0 21%. 166.7 +1 % 635 i1%. 750 176.0 +1% 100.0 +1 % 635 41% #as 161.0+1% 89.8 +1% 36+1% 900 149.0£1% 83.3 +1% 16+1% 1450 89.1+1% s17+1% 36+1% 1500 80.5 +1 % 50.0 +1 % 26+1% 1640 79.011% 45.7 41% 36+1% 1750 75241% pass 42.9 +1 % PaS$ 16+1% PAS$ 1800 72.011% 41.741% 36+1% 1900 68.0 +1 % so5+1% 16+1% 1950 66.3 41 % 38.5 +1 %. 16+1% 2000 645 +1% 375i:1% 16+1% 2100 s1.041% 35.7 +1% 26i1% 2300 55.5 41 % 326i1% 36+1% 2450 s1541% 30.4 +1% 16+1% 2600 as.5 +1% 288 +1% 16+1% 3000 415 +1% 25.0 +1 % 16+1% 3500 37.0:1% 264 +1 % 16+1% 3700 34.741% 264 £1% 16+1% Page: 6/10 This document shall not be reproduced, except in full or in part, without the writeen approval of ATIMO The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whole or part without written approval of SATTMO

(6. \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 2693.13.SATUA &'HN’ID 7 VALIDATION MEASUREMENT The IEEE Std. 1528, OET 65 Bulletin C and CEV/IEC 62209 standards state that the system validation measurements must be performed using a reference dipole meeting the fore mentioned return loss and mechanical dimension requirements. The validation measurement must be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. Per the standards, the dipole shall be positioned below the bottom of the phantom, with the dipole length centered and parallel to the longest dimension of the flat phantom, with the top surface ofthe dipole at the described distance from the bottom surface ofthe phantom. 7.1 MEASUREMENT CONDITION Software OPENSAR V4 Phantom SN 20/09 SAMT71 Probe SN 1871 EPG122 Liguid Head Liquid Values: eps_.39.9 sigma _1 37 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8m/dz=Smm Frequency 1750 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45% 7.2 HEAD LIQUID MEA NT is Relative permittivity (e,‘) Conductivity (0) $/m required measured required measured 300 45.3 25 % 0.87 15 % 450 43.5 15 % 0.87 15 % 750 41.9 15 % 0.89 15 % 835 41.5 15 % 0.90 15 % 900 415 15 % 0.97 15 % 1450 40.5 25 % 1.20 45 % 1500 40.4 25 % 1.23 25 % 1640 40.2 25 % 13115 % 1750 40.1 25 % PASS 137 45% PASS 1800 40.0 15 % 1.40 +5 % 1900 40.0 15 % 1.40 25 % 1950 40.0 15 % 1.40 15 % 2000 40.0 15 % 1.40 15 % 2100 39.8 15 % 1.49 15 % 2300 39.5 15 % 1.67 15 % 2450 39.2 25 % 1.80 45 % 2600 39.0 15 % 1.96 +5 % 3000 38.5 15 % 2.40 45 % 3500 37.9 15 % 2.91 15 % Page: 710 This document shall not be reproduced, except infill or in part, without the written approval ofSATIMO The information containedherein is to be used onlyfor thepurposefor which it is submitted and is not to be releasedin whole orpart without written approval ofSATIMO

{IV i SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 269.3.13.ATUA SATIMO 7.3 MEASUREMENT RESULT The IEEE Std. 1528 and CEVIEC 62209 standards state that the system validation measurements should produce the SAR values shown below (for phantom thickness of 2 mm), within the uncertainty for the system validation. All SAR values are normalized to 1 W forward power. In bracket, the measured SAR is given with the used input power. Eoi 1 8 SaR (W/ke/w) 10 g san (w/ke/w) required measured required measured 300 285 194 450 458 3.06 750 8.49 5.55 835 9.56 6.22 900 10.9 6.99 1450 29 16 1500 305 16.8 1640 34.2 184 1750 364 38.29 (3.83) 19.3 19.98 (2.00) 1800 384 20.1 1900 39.7 20.5 1950 40.5 20.9 2000 411 21.1 2100 43.6 219 2300 48.7 233 2450 524 24 2600 55.3 24.6 3000 63.8 25.7 3500 671 25 ta Page: 810 This document shall not be reproduced, except in full oin part, without the written approval o SATIMO The information containedhereinis to be used only for the purpose for which it is submittedand is not to be released in whole or part without written approval of ATTMO

SAR REFERENCE DIPOLECALIBRATION REPORT Ref: ACR.269.3.13.SATUA 74 BODY MEASUREMENT RESULT Software OPENSAR V4 Phantom SN 20/09 SAM7I Probe SN 18/11 EPG122 Liquid Body Liquid Values: eps‘ 51.5 sigma 1.47 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8m/dz=Smm Frequency 1750 MHz Input power 20 dBm Liguid Temperature zi °C Lab Temperature 21 °C Lab Humidity 45 % m““n':"(v 1 g SAR (W/ke/w) 10 g san (w/kg/w) measured measured 1750 40.12 (4.01) 21.58 (2.16) Page: 910 This document shall not bereproduced, except infull or in part, without the written approval of SATIMO: Theinformation containedhereinis to be usedonly for the purposefor which it is submitted and is not to be released in whole or part without written approval of S1TIMO

SAR REFERENCE DIPOLE CALIBRATION REPORT Ref ACR 269 3.13.8ATU.A 8 LIST OF EQUIPMENT Equipment Summary Sheet Equipment Manufacturer / Current Next Calibration Description Modet [19%49°=000 N91 pyypyojion Pate Date . Validated. No cal Validated. No call SAM Phantom Satimo SN—20/08—SAM71 Fequired fequired. . Validated. No cal Validated No cal COMOSAR Test Bench Version 3 NA fequired required. Network Analyzer RhO4e8Schware gop132 o22013 oaror6 Calipers Carrera CALIPER—01 1212010 1222013 . Characterized prior to |Characterized prior to Reference Probe Satimo EPG122 SN 18/11 test. No cal required. |test. No cal required Multimeter Keithley 2000 1188656 1172010 112013 Signal Generator Agilent E4438C MY49070581 1212010 1212013 Characterized prior to |Characterized prior to Amplifier Aethercomm sn 46 test. No cal required. |test. No cal required. Power Meter HP E4418A US38261498 1172010 1172013 Power Sensor HP ECP—E26A US37181460 1172010 1172013 omagl Characterized prior to |Characterized prior to Dirsctional Coupier Nerda 4216—20 01386 test. No calrequired. [test. No cal required. Temperature and Humidity Sensor Control Company 11—661—9 32012 32014 Page: 10/10 This document shall not be reproduced, exceptinfull or in part, without the writen approval ofSATIMO The information contained hereinis to be used onlyfor the purposefor which it is submitied and is not to be releasedin whole orpart without written approval ofSATTMO


Document Created: 2019-05-30 12:13:27
Document Modified: 2019-05-30 12:13:27
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC