SAR Report-6

FCC ID: R9C-R8006

RF Exposure Info

Download: PDF
FCCID_2237810

(/.\ SATIMO The micruware vison company .. SAR Reference Dipole Calibration Report Ref : ACR.261.3.13.SATU.A SHENZHEN MORLAB COMMUNICATIONS TECHNOLOGY CO., LTD FL3, BUILDING A, FEIYANG SCIENCE PARK, NO.8 LONGCHANG ROAD, BLOCK 67, BAOAN DISTRICT, SHENZHEN, GUANGDONG PROVINCE, P.R. CHINA SATIMO COMOSAR REFERENCE DIPOLE FREQUENCY: 835 MHZ SERIAL NO.: SN 20/08 DIPCI9 Calibrated at SATIMO US 2105 Barrett Park Dr. — Kennesaw, GA 30144 «a IACCIID"‘ID Caitemion CenT eazeo2 09/25/2013 Summary: This document presents the method and results from an accredited SAR reference dipole calibration performed in SATIMO USA using the COMOSAR test bench. All calibrationresults are traceable to national metrology institutions

B{Ah 3 \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref. ACR 2613.13.SATUA Name Function Date Signature Prepared by : Jérome LUC Product Manager 9/18/2013 fi’ Checked by : Jérome LUC Product Manager |9/18/2013 fi” Approved by : Kim RUTKOWSKI Quality Manager |9/18/2013 / ,, ast Customer Name Shenzhen Morlab Communications Distribution : ‘Technology Co., Ltd Issue Date Modifications A 9/18/2013 Initial release Page: 2710 This document shall not be reproduced, except in full or in part, without the writien approval ofSATTMO The information contained hereinis to be used onlyfor the purpasefor which it is submitted and is not to be released in whole orpart without written approval ofSATRO,

(t. SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.2613.13.8ATU A SATIMO z TABLE OF CONTENTS 1 IMETOGUCHOM.........sssccnnssnmmccnnmmmmnnnnnmmmmnnnnnnnnmmnnnnnnnmmnnnnnnnnnnnmnnnnnmnnnnnnnnmnnnnnnmmmmmin 4 2 DGVIC@ URGOL TOB.. oo iseccmccrmrmimcsmmnicsciccermemmetcresminereessmmmmennmminnersensemees 4 3 (FrOGUCLDESCHPHION.................... cualoonnommmammmenteiatbennmmramnemeting 4 3.1 General Information 4 4 Measurement Method. 4.1 Return Loss Requirements 5 4.2 Mechanical Requirements 5 5. MEBSUT@MENE UNCETEAIMTY ..............cssssssccnnnnnnmmncnnnmmmnnnnnnmmnnnnnnnmnnnnnnnmmnnnenemmmnnne 3 5.1 Return Loss 5 5.2 Dimension Measurement 5 5.3 Validation Measurement 5 6. (CaHDIRIION MESSUIOIONEROMIS:...... c sssessissssrremscccsmereemcrccsmemmmensstemmsrmtimenccisccieine 6 6.1 Return Loss 6.2 Mechanical Dimensions 6 7 Validation measurement... 7 7.1 Measurement Condition 7 7.2 Head Liquid Measurement 7 73 Measurement Result 8 7.4 Body Measurement Result 9 8 List of Equipment ... Page: 310 This document shallnot be reproduced, except infill or in part, without the writen approval ofSATIMO. The information contained hereinis to be usedonlyfor the purposefor which it is submitted and is not to be releasedin whole orpart without written approval ofSATBAO.

i. \ SAR REFERENCE DIPOLE CALIBRATION REPORT Rer Ack 261 5 13 SaTH A 1 INTRODUCTION This document contains a summary of the requirements set forth by the IEEE 1528, OET 65 Bulletin C and CEV/IEC 62209 standards for reference dipoles used for SAR measurement system validations and the measurements that were performed to verify that the product complies with the fore mentioned standards. 2 DEVICE UNDER TEST Device Under Test Device Type COMOSAR 835 MHz REFERENCE DIPOLE Manufacturer Satimo Model SID835 Serial Number SN 20/08 DIPCII Product Condition (new / used) Used A yearly calibration interval is recommended. 3 PRODUCT DESCRIPTION 34 GENERAL INFORMATION Satimo‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, OET 65 Bulletin C and CEUIEC 62209 standards. The product is designed for use with the COMOSAR test bench only. Figure 1 — Satimo COMOSAR Validation Dipole Page: 410 This document shall not be reproduced, except in fill or in part, without the writen approval ofSATTMO The information containedherein is to be usedonlyfor the purposefor which i is submitied and is not to be released in whole or part without written approval ofSATIMO.

(L.. SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.2613.13.8ATU A SATIMO — 4 MEASUREMENT METHOD The IEEE 1528, OET 65 Bulletin C and CEI/IEC 62209 standards provide requirements for reference dipoles used for system validation measurements. The following measurements were performed to verify that the product complies with the fore mentioned standards. 4.1 RETURN LOSS REQUIREMENTS The dipole used for SAR system validation measurements and checks must have a return loss of —20 dB or better. The return loss measurement shall be performed against a liquid filled flat phantom, with the phantom constucted as outlined in the fore mentioned standards. 4.2 MECHANICAL REQUIREMENTS The IEEE Std. 1528 and CEV/IEC 62209 standards specify the mechanical components and dimensions of the validation dipoles, with the dimensions frequency and phantom shell thickness dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2 mm phantom shell thickness. 5 MEASUREMENT UNCERTAINTY All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2, traceable to the Internationally Accepted Guides to Measurement Uncertainty. 5.1 RETURNLOSS The following uncertainties apply to the return loss measurement: Frequency band Expanded Uncertainty on Return Loss 400—6000MHz 0.1 dB 5.2 DIMENSION MEASUREMENT The following uncertainties apply to the dimension measurements: Length (mm) Expanded Uncertainty on Length 3 — 300 0.05 mm 5.3 VALIDATION MEASUREMENT The guidelines outlined in the IEEE 1528, OET 65 Bulletin C, CENELEC ENS0361 and CEMIEC 62209 standards were followed to generate the measurement uncertainty for validation measurements. Scan Volume Expanded Uncertainty 1 g 20.3 % 10 g 20.1 % Page: 510 This document shall not be reproduced, except infill or in part, without the writeen approval of$ATIMO The information containedhereini to be used onlyfor the purpose for which it is submitted and is not to be releasedin whole orpart without written approval ofSATBAO

f sArImo SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 261.3.13.SATU A 6 CALIBRATION MEASUREM T RE LTS 6.1 RETURNLOSS Frequency (MHz) Return Loss (dB) Requirement (dB) 835 —25,29 —20 6.2 MECHANICAL DIMENSIONS Frequency MHz L mm h mm d mm required measured required measured required measured 300 420.0 +1 %. 250.0 21 %. 635 41 % 450 290.0 +1 %. 166.7 +1 % 6.35 41 % 750 176.0 +1 %. 100.0 +1 % 635 +1 % #as 161.0 +1 %. Pass 89.8 +1 % paSs 1611% PAS$ 900 149.0 +1 % 83.3 +1 %. 3.641% 1450 89.1 +1 % 51.7 +1 % 3.611% 1500 80.5 21 % 50.0 41 %. 3.6 +1 % 1640 79.0 +1% 45.7 +1 % 3.641% 1750 75.2 +1 % 42.9 +1 %. 3.6+1% 1800 72.0 11 % 41.7 +1 %. 3.6+1% 1900 68.0 41 % 39.5 41 %. 3.6 11 %. 1950 66.3 +1 % 38.5 +1 %. 3.6 11 %. 2000 64.5 1 %. 37.5 41 %. 3.6 11 %. 2100 61.0 +1 % 35.7 41% 3611% 2300 55.5 41 % 32.6 +1 %. 3.6 +1 % 2450 51.5 41 % 30.4 41 %. 3.6 11 % 2600 48.5 11 % 28.8 +1 % 3611% 3000 41.5 +1 % 25.0 41 % 36 11% 3500 37.0+1 % 26.4 +1 % 3.6+1% 3700 34.721% 26.4 +1 %. 3.611% Page: 6/10 This document shall not bereproduced, except in fill or in part, without the written approval of SATIMO The information containedherein is to be used only for the purpose for whichit is submitied and is not to bereleasedin whole or part without written approval of SATIMO

("‘ 4 \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 261 3.13.SATU A 7 VALIDATION MEASUREMENT The IEEE Std. 1528, OET 65 Bulletin C and CEVIEC 62209 standards state that the system validation measurements must be performed using a reference dipole meeting the fore mentioned return loss and mechanical dimension requirements. The validation measurement must be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. Per the standards, the dipole shall be positioned below the bottom of the phantom, with the dipole length centered and parallel to the longest dimension of the flat phantom, with the top surface ofthe dipole at the described distance from the bottom surface of the phantom. 7.1 MEASUREMENT CONDITION Software OPENSAR V4 Phantom SN 20/09 SAMT7I Probe SN 18/11 EPG122 Liguid Head Liquid Values: eps‘ 42.6 sigma 0.88 Distance between dipole center and liquid 15.0 mm Area scan resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8m/dz=Smm Frequency 835 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45% 7.2 HEAD LIQUID MEASUREMENT hedm‘® Relative permittivity (e,) Conductivity (0) S/m required measured required measured 300 as3i5% D87 is% 450 43.5 15 % 0.87 25 % 750 mosy% o.89 i5 % s3s nse% pass 0.90 15 % Pass 900 41.5 5 % 0.97 15 % 1aso a05 :5 % 120i5% 1500 204 5% 125% 1640 40.2 45 % 131 15% 1750 a01 5% 125% 1800 40.0 15 % 1.40 15 % 1900 a0.0 25 % 14025 % 1950 40.0 25 % 1.40 15 % 2000 20015 % L40% 2100 39.8 15 % 149 15 % 2300 so5s% Ler#% 2aso 30245 % Leo:s% 2600 39.0 15 % 1.96 15 % 3000 385 i5% 2405% 3500 37.9 15 % 2.91 15 % Page: 710 This document shall not be reproduced, except in fill oin part, without the writeenapproval ofSATIMO. The information containedhereinis to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATBAO

\ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 261.3.13.8ATU A 7.3 MEASUREMENT RESULT Std. 1528 and CEVIEC 62209 standards state that the system validation measurements should produce the SAR values shown below (for phantom thickness of 2 mm), within the uncertainty for the system validation. All SAR values are normalized to 1 W forward power. In bracket, the measured SAR is given with the used input power rauie‘® 1 5 saR (W/ke/w) 10 g sar (w/ke/w) required measured required measured 300 285 1.94 450 4.58 3.06 750 8.49 5.55 835 9.56 9.71 (0.97) 6.22 6.27 (0.63) 900 10.9 6.99 1450 29 16 1500 30.5 16.8 1640 34.2 184 1750 36.4 193 1800 384 20.1 1900 39.7 205 1950 40.5 20.9 2000 411 211 2100 43.6 21.9 2300 48.7 233 2450 524 24 2600 55.3 24.6 3000 63.8 25.7 3500 67.1 25 Page: 810 This document shall not be reproduced, except in full or in part, without the writen approval of SATTMO The information containedherein is to be used only for the purpose for which it s submitied and is not to bereleased in whole or part without written approval ofSATDIO

(( Ls SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACK 261.3.13. 90 TU A SATIMO 74 BODY MEASUREMENT RESULT Software OPENSAR V4 Phantom SN 20(09 SAM7] Probe SN 18711 EPG122 Liquid Body Liquid Values: eps‘ 55.3 sigma : 0.96 Distance between dipole center and liquid 15.0 mm Area scan resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8m/dz=Smm Frequency 835 MHz Input power 20 dBm Liquid Temperature 21°C Lab Temperature 21°C Lab Humidity 45% F TV 18 SAR (W/ke/w) 10 g san (w/kg/w) measured measured 835 10.02 (1.00) 6.56 (0.66) ; "a Page: 910 This document shall not be reproduced, except in fillor in part, without the written approval of SATIMO Theinformation contained herein is to beused only for thepurpose for which i is submitted and is not to be released in whole or part without written approval of SATBMO

SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR 261 3,13.SATUA Cmpramopr1573 SAM Phantom Satimo SN—20/08—SAM71 gfi:fid No ce gfz:‘_" No cel |COMOSAR Test Bench] Version 3 NA :gfif;‘_” Nocel :fq'fizzd No call Network Analyzer RhOde8Schware grgoor32 o2ro13 o2ro16 Calipers Carrera caLiPEeR—01 1222010 122013 Reference Probe Satimo EPG122 SN 1871 g:’afif'c‘:mzl‘:;" z:f"’,if;':ffezfll‘:;" Multimeter Keithley 2000 1188655 112010 12013 Signal Generator Agilent E4438C MY49070581 1212010 122013 Ampitier Aethercomm Sm oen OMWetotmeinven(ostNeceredured. Power Meter HP E4418A ussezs1498 112010 12013 Power Sensor HP ECP—E26A ussr1814s0 112010 112013 Directional Coupler Narda 4216—20 o1386 z:f’afig’gfggzl‘:;" g;‘:’“fifgfg:fl;’eé‘_’ Lmfi:i’;‘;’:n:f Control Company 11486149 32012 aror4 Page: 10/10 This document shall not be reproduced, except infill or in part, without the writen approval of$ATTIMO The information contained herein is to be used onlyfor the purposefor which it is submittedand is not to be releasedin whole orpart without written approval ofSATBMO.


Document Created: 2013-09-27 11:06:06
Document Modified: 2013-09-27 11:06:06
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC