Manual

FCC ID: R7PSSMM1TRP

Users Manual

Download: PDF
FCCID_1918372

Certification Exhibit FCC ID: R7PSSMM1TRP FCC Rule Part: 15.247 ACS Project Number: 11-0372 Manufacturer: Landis+Gyr Technology, Inc. Model: Elster Solid State Meter Module Manual 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Elster Solid State Meter Module Quick Start Guide 12 Publication: 98-1258 Rev AB 20 / 8/ 12 ft ra D LANDIS+GYR CONFIDENTIAL INFORMATION

Limitation on Warranties and Liability Information in this document is subject to change without notice. This manual or any part of it thereof may not be re- produced in any form unless permitted by contract or by written permission of Landis+Gyr. In no event will Landis+Gyr be liable for any incidental, indirect, special, or consequential damages (including lost prof- its) arising out of or relating to this publication or the information contained in it, even if Landis+Gyr has been advised, knew, or should have known of the possibility of such damages. Other brands or product names used are the trademarks or registered trademarks of their respective holders. 12 © 2012 Landis+Gyr, Inc. All Rights Reserved Elster Solid State Meter Module Quick Start Guide 20 Publication: 98-1258 Revision History Modification Date Revision Description Author 8/ 9/10/2012 AA Released Vicky Costello 12/3/2012 AB In Process Vicky Costello / 12 Landis+Gyr 30000 Mill Creek Avenue, Suite 100 Alpharetta, GA 30022 Copyright© 2012 Landis+Gyr Website: www.landisgyr.com All rights reserved. E-mail: solutionsupport.na@landisgyr.com ft Technical Support: 1-888-390-5733 ra D

Elster Solid State Meter Module Quick Start Guide Overview The Landis+Gyr Solid State Meter Module (SSMM) is designed to provide active energy (Kilo-Watt hour) data from Elster ALPHA Plus meters for use in residential and industrial commercial services. 12 20 / 8/ 12 ft ra D Figure 1 - 1. Elster Solid State Meter Module The meter kit includes: • Elster ALPHA Plus meter (A1D+ or A1T+) • Communication Module (SSMM) • Antenna Landis+Gyr Confidential Information 98-1258 Rev AB 3

Elster Solid State Meter Module Quick Start Guide Landis+Gyr Required Software To work with the endpoint, you need at least one of the following software tools and documentation: • UtiliNet Solution Center (USC) • Meter Master Lite software • Meter Master Lite Quick Start Guide, publication number 98-0071 • Elster ALPHA Plus software Landis+Gyr recommends you have RF Verify software and the RF Verify User Guide, publication number 98-0069. Labels The endpoint contains the following labels: 12 1 20 / 8/ 12 2 3 ft ra Figure 2. Label Identification D Table 1. Elster Label Identification Label Description 1 Elster Meter Name Plate AEP compliant bar code that defines meter manufacturer, form, base, test voltage and current, watt-hour constant, serial number, and customer specific information. Manufacturer or customer specified serial number Manufacturer model and style number 2 Landis+Gyr FCC ID Federal Communications Commission (FCC) Identification (ID) number assigned to the Landis+Gyr Solid State Meter Module for use in the Elster Alpha+ meter. 3 Landis+Gyr LAN ID Identifies the Solid State Meter Module to the Landis+Gyr billing network (printed and barcoded). 4 98-1258 Rev AB Landis+Gyr Confidential Information

Landis+Gyr Elster Solid State Meter Module Quick Start Guide LAN ID The LAN ID is a unique identifier for each Landis+Gyr endpoint. Landis+Gyr provides the LAN address. You cannot change the LAN ID of a radio. Features and Functions Endpoint Registration The endpoint is automatically registered with the host system. No special tools are needed during installation. Admin packets are sent once each hour at a random time during the hour and play a crucial role in the automatic discovery of a meter by the Landis+Gyr system. They tell what kind of meter the 12 module interfaces with, and other characteristics, such as the scaling constant, number of dials, and the firmware version. Admin packets include: 20 Table 2. Admin Packet Information Meter ID Identifies the customer 8/ Protocol ID Identifies the type of meter. Scaling Constant Tells how to convert meter readings into real units such as kWh / Number of dials Also referred to as displayed digits. 12 Tells how much the meter reading can change in a certain period of Maximum Sensor Change Rate time. Firmware Version Specifies the firmware revision number. ft Current Cumulative Reading from the meter ra Communication and Retrieving Data A microprocessor on the communications module counts pulses, records usage over multiple D intervals, and transmits the information to the head end system. Several different packet types are sent.The most frequently sent packet contains the current rotational count and historical interval data that is useful for load profiling and time-of-use metering. Another less frequently sent (Admin) packet contains the current cumulative rotation count, useful for basic automatic meter reading applications. An Admin packet is sent once hourly and contains the information listed in Table 2, “Admin Packet Information,” on page 5. Power Outage/Restoration When an outage occurs, the meter uses an early power failure signal to alert the communication module. The communication module saves critical endpoint data to non-volatile memory, creates and sends a power fail message to the host system that includes the LAN ID. When power is restored, the communication module sends a Power Up message to the host system. This message includes the following information: Landis+Gyr Confidential Information 98-1258 Rev AB 5

Elster Solid State Meter Module Quick Start Guide Landis+Gyr • LAN ID • Total count • Last ten interval counts Customer Service Contact Landis+Gyr Customer Support at solutionsupport.na@landisgyr.com or call 888-390-5733 with any questions or problems for guidance through the troubleshooting process. Compliance 12 FCC Class B This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 20 (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 8/ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection / against harmful interference in a residential installation. This equipment generates, uses, and can 12 radiate radio frequency energy and, if not installed and used in accordance with the Instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following ft measures: ra • Reorient or relocate the antenna. • Increase the separation between the equipment and receiver. D • Consult Landis+Gyr or an experienced radio technician for help. U WARNING: Changes or modifications to this device not expressly approved by Landis+Gyr could void the user’s authority to operate the equipment. 6 98-1258 Rev AB Landis+Gyr Confidential Information

Landis+Gyr Elster Solid State Meter Module Quick Start Guide RF Exposure In accordance with FCC requirements of human exposure to radio frequency fields, the radiating element shall be installed such that a minimum separation distance of 20 centimeters will be maintained. Host FCC Label Requirement In the final installation, the following information must be visible: “Contains FCC ID: R7PSSMM1TRP This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and 12 (2) This device must accept any interference received, including interference that may cause undesired operation.” 20 / 8/ 12 ft ra D Landis+Gyr Confidential Information 98-1258 Rev AB 7

Elster Solid State Meter Module Quick Start Guide Landis+Gyr Product Specifications Table 3. Elster Solid State Meter Module Specifications Category Specification Value or Range Form Class 1S 200 1S 320 2S 200 2S 320 3S 20 4S 20 12 35S 20 35A 20 20 Elster ALPHA Plus Supported 12S 200 Meter Forms Compatible 12S 320 Meters NOTE: Contact Elster 13S 200 Electricity for 8/ additional forms. 13S 320 13A 100 / 36S 20 12 36A 20 9S 20 10S 20 ft 10A 20 ra 16S 200 16S 320 16A 100 D 13.5VDC + 1V, 50mA (limited Voltage duration from meter’s power Electrical supply) Input Current 50mA Output Power 22-26.5 dBm RF Transmit Frequency 917.58 MHz (Fixed)) 8 98-1258 Rev AB Landis+Gyr Confidential Information

Landis+Gyr Elster Solid State Meter Module Quick Start Guide Table 3. Elster Solid State Meter Module Specifications Category Specification Value or Range FCC Title 47 CFR Part 15 Radiated and Conducted Subpart B & C Emissions IEC 61000 4-2,3,4,5 Electromagnetic Compatibility ANSI C12.1-2011 Electricity Metering Standards ANSI C12.20-2002 Electricity Meters Standard Compliance Substation Standards - Fast ANSI C37.90.1 Transient and Oscillatory Waveform Workmanship Standard for ANSI/IPC-A-610-Class 2 Electronic Assemblies 12 Outdoor, rain-protected, General Environmental sunlight-exposed -40 to +85 C (under meter Environmental Operating Temperature Range 20 glass) 10% to 95% relative humidity, Humidity non-condensing 8/ Refer to Elster Technical Size (Meter & Module) Manual, TM42-2182E for more details. Mechanical / Refer to Elster Technical 12 Weight (Meter & Module) Manual, TM42-2182E for more details. ft ra D Landis+Gyr Confidential Information 98-1258 Rev AB 9

Elster Solid State Meter Module Quick Start Guide Landis+Gyr Physical Dimensions The ALPHA Plus meter fits all standard S-base services. Meters with an A-base are also available. Figure 1 - 1 illustrates the S-base meter type and dimensions.  NOTE: The dimensions are for reference purposes only and should not be used for construction. 12 20 / 8/ 12 Figure 1 - 1. S-base Meter Type and Dimensions in Inches (millimeters) - Front and Side View Figure 1 - 2 and Figure 1 - 3 illustrate the A-base meter type and dimensions. ft ra D 10 98-1258 Rev AB Landis+Gyr Confidential Information

Landis+Gyr Elster Solid State Meter Module Quick Start Guide 12 20 8/ Figure 1 - 2. A-base Meter Type and Dimensions in Inches (millimeters) - Front and Side View / 12 ft ra D Figure 1 - 3. A-base Meter Type and Dimensions in Inches (millimeters) - Back View Landis+Gyr Confidential Information 98-1258 Rev AB 11

Elster Solid State Meter Module Quick Start Guide Landis+Gyr 12 20 / 8/ 12 ft ra D 12 98-1258 Rev AB Landis+Gyr Confidential Information


Document Created: 2013-01-21 14:17:23
Document Modified: 2013-01-21 14:17:23
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC