Test Report

FCC ID: R7PNG0R1S1

Test Report

Download: PDF

FCCID_1921383

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

2 TEST FACILITIES

2.1 Location

The radiated and conducted emissions test sites are located at the following address:

Advanced Compliance Solutions
5015 B.U. Bowman Drive
Buford, GA 30518
Phone: (770) 831-8048
Fax: (770) 831-8598

2.2 Laboratory Accreditations/Recognitions/Certifications

ACS is accredited to ISO/IEC 17025 by the National Institute of Standards and Technology under
their National Voluntary Laboratory Accreditation Program (NVLAP), Lab Code 200612-0. Unless
otherwise specified, all tests methods described within this report are covered under the ISO/IEC
17025 scope of accreditation.

The Semi-Anechoic Chamber Test Site, Open Area Test Site (OATS) and Conducted Emissions
Site have been fully described, submitted to, and accepted by the FCC, Industry Canada and the
Japanese Voluntary Control Council for Interference by information technology equipment.

FCC Registration Number: 511277
Industry Canada Lab Code: IC 4175A-1
VCCI Member Number: 1831
• VCCI OATS Registration Number R-1526
• VCCI Conducted Emissions Site Registration Number: C-1608

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 4

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

2.3 Radiated Emissions Test Site Description

2.3.1 Semi-Anechoic Chamber Test Site

The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The
chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid is
101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on steel
panels and installed directly on the inner walls of the chamber.

The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The
chamber is grounded via 1 – 8’ copper ground rod, installed at the center of the back wall, it is
bound to the ground plane using 3/4” stainless steel braided cable.

The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely
operated from inside the control room located 25’ from the range. The turntable is electrically
bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table.
The steel fingers make constant contact with the ground plane during operation.

Behind the turntable is a 3’ x 6’ x 4’ deep shielded pit used for support equipment if necessary.
The pit is equipped with 1 – 4” PVC chases from the turntable to the pit that allow for cabling to
the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can
be supplied to the EUT from the pit.

A diagram of the Semi-Anechoic Chamber Test Site is shown in Figure 2.3-1 below:

3 Meters

5 Feet
Diameter

20 Feet

30 Feet
Figure 2.3-1: Semi-Anechoic Chamber Test Site

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 5

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

2.3.2 Open Area Tests Site (OATS)

The open area test site consists of a 40’ x 66’ concrete pad covered with a perforated electro-
plated galvanized sheet metal. The perforations in the sheet metal are 1/8” holes that are
staggered every 3/16”. The individual sheets are placed to overlap each other by 1/4” and are
riveted together to provide a continuous seam. Rivets are spaced every 3” in a 3 x 20 meter
perimeter around the antenna mast and EUT area. Rivets in the remaining area are spaced as
necessary to properly secure the ground plane and maintain the electrical continuity.

The entire ground plane extends 12’ beyond the turntable edge and 16’ beyond the antenna mast
when set to a 10 meter measurement distance. The ground plane is grounded via 4 – 8’ copper
ground rods, each installed at a corner of the ground plane and bound to the ground plane using
3/4” stainless steel braided cable.

The turntable is an all aluminum 10’ flush mounted table installed in an all aluminum frame. The
table is remotely operated from inside the control room located 40’ from the range. The turntable
is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of
the turn table. The steel fingers make constant contact with the ground plane during operation.

Adjacent to the turntable is a 7’ x 7’ square and 4’ deep concrete pit used for support equipment if
necessary. The pit is equipped with 5 – 4” PVC chases from the pit to the control room that allow
for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit
so cables can be supplied to the EUT from the pit. The pit is covered with 2 sheets of 1/4”
diamond style re-enforced steel sheets. The sheets are painted to match the perforated steel
ground plane; however the underside edges have been masked off to maintain the electrical
continuity of the ground plane. All reflecting objects are located outside of the ellipse defined in
ANSI C63.4.

A diagram of the Open Area Test Site is shown in Figure 2.3-2 below:

10

3 Meters

40

7x7x4
Pit

66 Feet

Figure 2.3-2: Open Area Test Site

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 6

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

4 LIST OF TEST EQUIPMENT

The calibration interval of test equipment is annually or the manufacturer’s recommendations.
Where the calibration interval deviates from the annual cycle based on the instrument
manufacturer’s recommendations, it shall be stated below.

Table 4-1: Test Equipment
Calibration
AssetID Manufacturer Model # Equipment Type Serial # Last Calibration Date Due Date
1 Rohde & Schwarz ESMI - Display Spectrum Analyzers 833771/007 8/2/2012 8/2/2014
2 Rohde & Schwarz ESMI-Receiver Spectrum Analyzers 839587/003 8/2/2012 8/2/2014
30 Spectrum Technologies DRH-0118 Antennas 970102 4/27/2011 4/27/2013
40 EMCO 3104 Antennas 3211 2/11/2011 2/11/2013
73 Agilent 8447D Amplifiers 2727A05624 9/28/2012 9/28/2013
Chamber EMI
167 ACS Cable Set Cable Set 167 12/21/2011 12/21/2012
Chamber EMI
167 ACS Cable Set Cable Set 167 12/17/2012 12/17/2013
267 Agilent N1911A Meters MY45100129 1/23/2012 1/23/2014
268 Agilent N1921A Sensors MY45240184 1/17/2012 1/17/2014
283 Rohde & Schwarz FSP40 Spectrum Analyzers 1000033 8/1/2012 8/1/2013
SMRE-200W-12.0-
291 Florida RF Cables SMRE Cables None 11/20/2012 11/20/2013
SMR-290AW-
292 Florida RF Cables 480.0-SMR Cables None 4/2/2012 4/2/2013
337 Microwave Circuits H1G513G1 Filters 282706 7/2/2012 7/2/2013
338 Hewlett Packard 8449B Amplifiers 3008A01111 8/2/2012 8/2/2013
340 Aeroflex/Weinschel AS-20 Attenuators 7136 8/2/2012 8/2/2013
412 Electro Metrics LPA-25 Antennas 1241 7/27/2012 7/27/2014
SMS-200AW-72.0-
422 Florida RF SMR Cables 805 11/20/2012 11/20/2013

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 8

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

5 SUPPORT EQUIPMENT

Table 5-1: Support Equipment
Item Equipment Type Manufacturer Model Number Serial Number
DC Bench Power
1 Hewlett Packard E3630A KR64308603
Supply

6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM

EUT

A

1
B

AC Mains

A – 1.5m Unshielded DC Power Cable (twisted)
B – 1.5m Unshielded AC Power Cable

Figure 6-1: Test Setup Block Diagram

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 9

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

* RBW 1 kHz Marker 1 [T1 ] * RBW 1 kHz Marker 1 [T1 ]
VBW 3 kHz 18.16 dBm VBW 3 kHz 19.52 dBm
Ref 30 dBm Att 50 dB SWT 50 ms 927.895300000 MHz Ref 30 dBm Att 30 dB SWT 50 ms 902.105500000 MHz
30 Offset 19.7 dB ndB [T1] 20.00 dB 30 Offset 19.7 dB OBW 22.300000000 kHz
BW 23.800000000 kHz Temp 1 [T1 OBW]
1
1 Temp 1 [T1 ndB] A 2.98 dBm A
20 20
-1.76 dBm 902.089200000 MHz
1 PK 1 SA *
927.888300000 MHz Temp 2 [T1 OBW]
VIEW VIEW
10 Temp 2 [T1 ndB] 10 2.85 dBm LVL
LVL
-1.66 dBm T1 T2 902.111500000 MHz
T1 T2927.912100000 MHz
0 0

-10 -10

-20 -20

3DB 3DB
-30 -30

-40 -40

-50 -50

-60 -60

-70 -70

Center 927.9 MHz 5 kHz/ Span 50 kHz Center 902.1 MHz 5 kHz/ Span 50 kHz

Date: 21.DEC.2012 10:01:07 Date: 21.DEC.2012 09:46:57

Figure 7.3.2-3: 20dB BW High Channel Figure 7.3.2-4: 99% BW Low Channel
* RBW 1 kHz Marker 1 [T1 ] * RBW 1 kHz Marker 1 [T1 ]
VBW 3 kHz 20.54 dBm VBW 3 kHz 18.37 dBm
Ref 30 dBm Att 30 dB SWT 50 ms 914.995000000 MHz Ref 30 dBm Att 30 dB SWT 50 ms 927.895000000 MHz
30 Offset 19.7 dB OBW 21.500000000 kHz 30 Offset 19.7 dB OBW 22.300000000 kHz
1 Temp 1 [T1 OBW] Temp 1 [T1 OBW]
3.04 dBm A 1 0.98 dBm A
20 20
914.989300000 MHz 927.889000000 MHz
1 SA * 1 SA *
Temp 2 [T1 OBW] Temp 2 [T1 OBW]
VIEW VIEW
10 3.53 dBm LVL 10 0.52 dBm LVL
T1 T2 915.010800000 MHz 927.911300000 MHz
T1 T2
0 0

-10 -10

-20 -20

3DB 3DB
-30 -30

-40 -40

-50 -50

-60 -60

-70 -70

Center 915 MHz 5 kHz/ Span 50 kHz Center 927.9 MHz 5 kHz/ Span 50 kHz

Date: 21.DEC.2012 09:55:24 Date: 21.DEC.2012 10:02:48

Figure 7.3.2-5: 99% BW Mid Channel Figure 7.3.2-6: 99% BW High Channel

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 12

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

7.4.2 RF Conducted Spurious Emissions

7.4.2.1 Measurement Procedure

The RF output port of the EUT was directly connected to the input of the spectrum analyzer. The
EUT was investigated for conducted spurious emissions from 30MHz to 10GHz, 10 times the
highest fundamental frequency. Measurements were made at the low, center and high channels
of the EUT. For each measurement, the spectrum analyzer’s RBW was set to 100kHz. A peak
detector function was used with the trace set to max hold.

7.4.2.2 Measurement Results
Results are shown below in Figures 7.4.2.2-1 to 7.4.2.2-6:
* RBW 100 kHz Marker 2 [T1 ] * RBW 100 kHz Marker 2 [T1 ]
VBW 300 kHz -22.99 dBm VBW 300 kHz -24.82 dBm
Ref 30 dBm Att 50 dB SWT 100 ms 771.080000000 MHz Ref 20 dBm Att 40 dB SWT 900 ms 7.102000000 GHz
30 Offset 19.7 dB Marker 1 [T1 ] 20 Offset 19.7 dB Marker 1 [T1 ]
20.62
1 dBm -24.37 dBm
903.000000000 MHz B 8.380000000 GHz B
20 10

1 PK 1 PK
VIEW VIEW D1 0.62 dBm
10 0
LVL LVL

0 D1 0.62 dBm -10

-10 -20
2 1

-20 2 -30

3DB 3DB
-30 -40

-40 -50

-50 -60

-60 -70

-70 -80

Start 30 MHz 97 MHz/ Stop 1 GHz Start 1 GHz 900 MHz/ Stop 10 GHz

Date: 21.DEC.2012 09:51:56 Date: 21.DEC.2012 09:52:33

Figure 7.5.2.2-1: 30 MHz – 1 GHz – Low Channel Figure 7.5.2.2-2: 1 GHz – 10 GHz – Low Channel

* RBW 100 kHz Marker 2 [T1 ] * RBW 100 kHz Marker 2 [T1 ]
VBW 300 kHz -23.09 dBm VBW 300 kHz -24.89 dBm
Ref 30 dBm Att 50 dB SWT 100 ms 829.280000000 MHz Ref 20 dBm Att 40 dB SWT 900 ms 7.084000000 GHz
30 Offset 19.7 dB Marker 1 [T1 ] 20 Offset 19.7 dB Marker 1 [T1 ]
20.83
1 dBm -24.76 dBm
916.580000000 MHz B 3.034000000 GHz B
20 10

1 PK 1 PK
VIEW VIEW D1 0.83 dBm
10 0
LVL LVL

0 D1 0.83 dBm -10

-10 -20
1 2

-20 2 -30

3DB 3DB
-30 -40

-40 -50

-50 -60

-60 -70

-70 -80

Start 30 MHz 97 MHz/ Stop 1 GHz Start 1 GHz 900 MHz/ Stop 10 GHz

Date: 21.DEC.2012 10:07:27 Date: 21.DEC.2012 10:08:09

Figure 7.5.2.2-3: 30 MHz – 1 GHz –Mid Channel Figure 7.5.2.2-4: 1 GHz – 10 GHz – Mid Channel

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 14

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

* RBW 100 kHz Marker 2 [T1 ] * RBW 100 kHz Marker 2 [T1 ]
VBW 300 kHz -23.20 dBm VBW 300 kHz -24.75 dBm
Ref 30 dBm Att 50 dB SWT 100 ms 790.480000000 MHz Ref 20 dBm Att 40 dB SWT 900 ms 9.712000000 GHz
30 Offset 19.7 dB Marker 1 [T1 ] 20 Offset 19.7 dB Marker 1 [T1 ]
18.93 dBm -25.05 dBm
1 B B
20 930.160000000 MHz 10 9.010000000 GHz

1 PK 1 PK
VIEW VIEW
10 0 D1 -1.07 dBm
LVL LVL

0 D1 -1.07 dBm -10

-10 -20
1 2

-20 2 -30

3DB 3DB
-30 -40

-40 -50

-50 -60

-60 -70

-70 -80

Start 30 MHz 97 MHz/ Stop 1 GHz Start 1 GHz 900 MHz/ Stop 10 GHz

Date: 21.DEC.2012 10:05:49 Date: 21.DEC.2012 10:06:31

Figure 7.5.2.2-5: 30 MHz – 1 GHz – High Channel Figure 7.5.2.2-6: 1 GHz – 10 GHz –High Channel

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 15

Model: Utilinet, Modular SCADA/DA FCC ID: R7PNG0R1S1 IC: 5294A-NG0R1S1

Table 7.4.3.2-2: Radiated Spurious Emissions Tabulated Data – Y Position
Level Antenna Correction Corrected Level Limit Margin
Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB)
(MHz)
pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg
Low Channel
961 --------- 40.45 H 1.49 --------- 41.94 -------- 54.0 --------- 12.1
961 --------- 46.37 V 1.49 --------- 47.86 -------- 54.0 --------- 6.1
2706.3 48.62 41.10 H -3.68 44.94 37.42 74.0 54.0 29.1 16.6
2706.3 50.72 45.06 V -3.68 47.04 41.38 74.0 54.0 27.0 12.6
3608.4 48.17 38.08 H -0.49 47.68 37.59 74.0 54.0 26.3 16.4
Middle Channel
973.96 --------- 38.52 H 1.56 --------- 40.08 -------- 54.0 --------- 13.9
973.96 --------- 42.58 V 1.56 --------- 44.14 -------- 54.0 --------- 9.9
2745 48.51 40.44 H -3.56 44.95 36.88 74.0 54.0 29.0 17.1
2745 48.01 40.74 V -3.56 44.45 37.18 74.0 54.0 29.5 16.8
3660 47.27 37.75 H -0.25 47.02 37.50 74.0 54.0 27.0 16.5
7320 47.32 40.85 H 7.74 55.06 48.59 74.0 54.0 18.9 5.4
High Channel
979.5 --------- 33.24 H 1.78 --------- 35.02 -------- 54.0 --------- 19.0
979.5 --------- 38.45 V 1.78 --------- 40.23 -------- 54.0 --------- 13.8
986.86 --------- 35.02 H 1.87 --------- 36.89 -------- 54.0 --------- 17.1
986.86 --------- 41.39 V 1.87 --------- 43.26 -------- 54.0 --------- 10.7

Table 7.4.3.2-3: Radiated Spurious Emissions Tabulated Data – Z Position
Level Antenna Correction Corrected Level Limit Margin
Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB)
(MHz)
pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg
Low Channel
961 --------- 40.71 H 1.49 --------- 42.20 -------- 54.0 --------- 11.8
961 --------- 45.56 V 1.49 --------- 47.05 -------- 54.0 --------- 7.0
2706.3 47.17 36.35 H -3.68 43.49 32.67 74.0 54.0 30.5 21.3
2706.3 49.02 41.28 V -3.68 45.34 37.60 74.0 54.0 28.7 16.4
Middle Channel
973.96 --------- 40.30 H 1.56 --------- 41.86 -------- 54.0 --------- 12.1
973.96 --------- 41.29 V 1.56 --------- 42.85 -------- 54.0 --------- 11.2
2745 46.41 36.15 H -3.56 42.85 32.59 74.0 54.0 31.1 21.4
2745 47.52 38.56 V -3.56 43.96 35.00 74.0 54.0 30.0 19.0
7320 46.01 37.39 H 7.74 53.75 45.13 74.0 54.0 20.3 8.9
High Channel
986.86 --------- 35.50 H 1.87 --------- 37.37 -------- 54.0 --------- 16.6
986.86 --------- 41.52 V 1.87 --------- 43.39 -------- 54.0 --------- 10.6
2783.7 49.06 41.84 V -3.43 45.63 38.41 74.0 54.0 28.4 15.6

ACS Report: 12-0529.W04.1A Advanced Compliance Solutions Page 17

Document Created: 2013-03-13 16:06:59
Document Modified: 2013-03-13 16:06:59

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC