Test Report

FCC ID: R7PEG1R1S6

Test Report

Download: PDF
FCCID_2789324

Certification Test Report FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-247 ACS Report Number: 15-0242.W06.2A Manufacturer: Landis+Gyr Technology, Inc. Model: G5 Integrated Focus AXe Test Begin Date: August 31, 2015 Test End Date: September 3, 2015 Report Issue Date: September 11, 2015 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612-0 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Reviewed by: Kirby Munroe Director, Wireless Certifications ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 20 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

TABLE OF CONTENTS 1 GENERAL ............................................................................................................................................ 3 1.1 PURPOSE.......................................................................................................................................... 3 1.2 PRODUCT DESCRIPTION ................................................................................................................... 3 1.3 TEST METHODOLOGY AND CONSIDERATIONS ................................................................................. 3 2 TEST FACILITIES .............................................................................................................................. 4 2.1 LOCATION ....................................................................................................................................... 4 2.2 LABORATORY ACCREDITATIONS/RECOGNITIONS/CERTIFICATIONS ................................................ 4 2.3 RADIATED EMISSIONS TEST SITE DESCRIPTION .............................................................................. 5 2.3.1 Semi-Anechoic Chamber Test Site .......................................................................................... 5 2.3.2 Open Area Tests Site (OATS) ................................................................................................. 6 2.4 CONDUCTED EMISSIONS TEST SITE DESCRIPTION ........................................................................... 7 3 APPLICABLE STANDARD REFERENCES.................................................................................... 7 4 LIST OF TEST EQUIPMENT ............................................................................................................ 8 5 SUPPORT EQUIPMENT .................................................................................................................... 9 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ........................................................... 9 7 SUMMARY OF TESTS ......................................................................................................................10 7.1 ANTENNA REQUIREMENT – FCC 15.203 ........................................................................................10 7.2 POWER LINE CONDUCTED EMISSIONS – FCC 15.207, IC: RSS-GEN 8.8 ........................................10 7.2.1 Measurement Procedure ........................................................................................................10 7.2.2 Measurement Results .............................................................................................................10 7.3 6DB / 99% BANDWIDTH – FCC 15.247(A)(2), IC: RSS-247 5.2(1) ................................................12 7.3.1 Measurement Procedure ........................................................................................................12 7.3.2 Measurement Results .............................................................................................................12 7.4 FUNDAMENTAL EMISSION OUTPUT POWER – FCC 15.247(B)(3), IC: RSS-247 5.4(4) ...................14 7.4.1 Measurement Procedure ........................................................................................................14 7.4.2 Measurement Results .............................................................................................................14 7.5 EMISSION LEVELS – FCC 15.247(D), 15.205, 15.209; IC RSS-247 5.5, RSS-GEN 8.9....................15 7.5.1 Emissions into Non-restricted Frequency Bands ...................................................................15 7.5.1.1 Measurement Procedure ................................................................................................................... 15 7.5.1.2 Measurement Results ....................................................................................................................... 15 7.5.2 Emissions into Restricted Frequency Bands ..........................................................................17 7.5.2.1 Measurement Procedure ................................................................................................................... 17 7.5.2.2 Duty Cycle Correction ..................................................................................................................... 17 7.5.2.3 Measurement Results ....................................................................................................................... 17 7.5.2.4 Sample Calculation: ......................................................................................................................... 18 7.6 MAXIMUM POWER SPECTRAL DENSITY IN THE FUNDAMENTAL EMISSION – FCC 15.247(E) IC: RSS-247 5.2(2) ..........................................................................................................................................19 7.6.1 Measurement Procedure ........................................................................................................19 7.6.2 Measurement Results .............................................................................................................19 8 CONCLUSION ....................................................................................................................................20 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 1 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification RSS-247 Certification for modular approval. 1.2 Product Description The G5 Integrated Focus AXe contains (1) 900 MHz LAN frequency hopping spread spectrum radio and (1) 2.4 GHz direct sequence spread spectrum Zigbee radio. This report addresses the 2.4 GHz direct sequence spread spectrum Zigbee radio only. Technical Information: Detail Description Frequency Range 2405 – 2475 MHz Number of Channels 15 Modulation Format O-QPSK Operating Voltage 3.3Vdc Antenna Type / Gain PIFA / 6 dBi Manufacturer Information: Landis+Gyr Technology, Inc. 30000 Mill Creek Ave., Suite 100 Alpharetta, GA 30022 EUT Serial Numbers: 90600060 (Radiated), 9060005F (Conducted) Test Sample Condition: The test samples were provided in good working order with no visible defects. 1.3 Test Methodology and Considerations The EUT was evaluated in three orthogonal orientations. The worst case orientation was X- position. Both the 900 MHz LAN radio and the 2.4 GHz Zigbee radio can transmit simultaneously therefore radiated inter-modulation products were evaluated and found to be in compliance. Software power setting during test: -2; -5 (high channel) ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 3

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 2 TEST FACILITIES 2.1 Location The radiated and conducted emissions test sites are located at the following address: Advanced Compliance Solutions 5015 B.U. Bowman Drive Buford, GA 30518 Phone: (770) 831-8048 Fax: (770) 831-8598 2.2 Laboratory Accreditations/Recognitions/Certifications ACS is accredited to ISO/IEC 17025 by the National Institute of Standards and Technology under their National Voluntary Laboratory Accreditation Program (NVLAP), Lab Code 200612-0. Unless otherwise specified, all tests methods described within this report are covered under the ISO/IEC 17025 scope of accreditation. The Semi-Anechoic Chamber Test Site, Open Area Test Site (OATS) and Conducted Emissions Site have been fully described, submitted to, and accepted by the FCC, Industry Canada and the Japanese Voluntary Control Council for Interference by information technology equipment. FCC Registration Number: 511277 Industry Canada Lab Code: IC 4175A VCCI Member Number: 1831 • VCCI OATS Registration Number R-1526 • VCCI Conducted Emissions Site Registration Number: C-1608 ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 4

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 2.3 Radiated Emissions Test Site Description 2.3.1 Semi-Anechoic Chamber Test Site The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid is 101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on steel panels and installed directly on the inner walls of the chamber. The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The chamber is grounded via 1 - 8’ copper ground rod, installed at the center of the back wall, it is bound to the ground plane using 3/4" stainless steel braided cable. The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely operated from inside the control room located 25’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Behind the turntable is a 3’ x 6’ x 4’ deep shielded pit used for support equipment if necessary. The pit is equipped with 1 - 4” PVC chases from the turntable to the pit that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. A diagram of the Semi-Anechoic Chamber Test Site is shown in Figure 2.3-1 below: 3 Meters 5 Feet Diameter 20 Feet 30 Feet Figure 2.3-1: Semi-Anechoic Chamber Test Site ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 5

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 2.3.2 Open Area Tests Site (OATS) The open area test site consists of a 40’ x 66’ concrete pad covered with a perforated electro- plated galvanized sheet metal. The perforations in the sheet metal are 1/8” holes that are staggered every 3/16”. The individual sheets are placed to overlap each other by 1/4” and are riveted together to provide a continuous seam. Rivets are spaced every 3” in a 3 x 20 meter perimeter around the antenna mast and EUT area. Rivets in the remaining area are spaced as necessary to properly secure the ground plane and maintain the electrical continuity. The entire ground plane extends 12’ beyond the turntable edge and 16’ beyond the antenna mast when set to a 10 meter measurement distance. The ground plane is grounded via 4 - 8’ copper ground rods, each installed at a corner of the ground plane and bound to the ground plane using 3/4" stainless steel braided cable. The turntable is an all aluminum 10’ flush mounted table installed in an all aluminum frame. The table is remotely operated from inside the control room located 40’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Adjacent to the turntable is a 7’ x 7’ square and 4’ deep concrete pit used for support equipment if necessary. The pit is equipped with 5 - 4” PVC chases from the pit to the control room that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. The pit is covered with 2 sheets of 1/4" diamond style re-enforced steel sheets. The sheets are painted to match the perforated steel ground plane; however the underside edges have been masked off to maintain the electrical continuity of the ground plane. All reflecting objects are located outside of the ellipse defined in ANSI C63.4. A diagram of the Open Area Test Site is shown in Figure 2.3-2 below: 10Meter 3 Meters 40Feet 7x7x4 Pit 66 Feet Figure 2.3-2: Open Area Test Site ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 6

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 2.4 Conducted Emissions Test Site Description The AC mains conducted EMI site is located in the main EMC lab. It consists of an 8’ x 8’ solid aluminum horizontal ground reference plane (GRP) bonded every 3” to an 8’ X 8’ vertical ground plane. The site is of sufficient size to test table top and floor standing equipment in accordance with section 6.1.4 of ANSI C63.4. A diagram of the room is shown below in figure 4.1.3-1: Vertical Ground Plane (8’ x 8’) Non-Conductive EUT Table (1m x 1.5m x .8m) .4 Meters .8 Meters Horizontal Ground Plane (8’ x 8’) LISN Figure 2.4-1: AC Mains Conducted EMI Site 3 APPLICABLE STANDARD REFERENCES The following standards were used:  ANSI C63.10-2013: American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices  US Code of Federal Regulations (CFR): Title 47, Part 2, Subpart J: Equipment Authorization Procedures, 2015  US Code of Federal Regulations (CFR): Title 47, Part 15, Subpart C: Radio Frequency Devices, Intentional Radiators, 2015  FCC KDB 558074 D01 DTS Meas Guidance v03r03 - Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under §15.247, June 9, 2015  Industry Canada Radio Standards Specification: RSS-247 – Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and License-Exempt Local Area Network (LE-LAN) Devices, Issue 1, May 2015  Industry Canada Radio Standards Specification: RSS-GEN – General Requirements for Compliance of Radio Apparatus, Issue 4, Nov 2014. ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 7

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 4 LIST OF TEST EQUIPMENT The calibration interval of test equipment is annually or the manufacturer’s recommendations. Where the calibration interval deviates from the annual cycle based on the instrument manufacturer’s recommendations, it shall be stated below. Table 4-1: Test Equipment Calibration AssetID Manufacturer Model # Equipment Type Serial # Last Calibration Date Due Date 1 Rohde & Schwarz ESMI - Display Spectrum Analyzers 833771/007 7/14/2015 7/14/2016 2 Rohde & Schwarz ESMI-Receiver Spectrum Analyzers 839587/003 7/14/2015 7/14/2016 22 Agilent 8449B Amplifiers 3008A00526 5/18/2015 5/18/2016 30 Spectrum Technologies DRH-0118 Antennas 970102 4/30/2015 4/30/2017 40 EMCO 3104 Antennas 3211 2/10/2015 2/10/2017 73 Agilent 8447D Amplifiers 2727A05624 7/15/2015 7/15/2016 Chamber EMI 167 ACS Cable Set Cable Set 167 10/28/2014 10/28/2015 168 Hewlett Packard 11947A Attenuators 44829 1/19/2015 1/19/2016 267 Agilent N1911A Meters MY45100129 8/24/2015 8/24/2017 268 Agilent N1921A Sensors MY45240184 8/13/2015 8/13/2017 SMR-290AW- 292 Florida RF Cables 480.0-SMR Cables None 3/3/2015 3/3/2016 324 ACS Belden Cables 8214 5/5/2015 5/5/2016 340 Aeroflex/Weinschel AS-20 Attenuators 7136 7/13/2015 7/13/2016 412 Electro Metrics LPA-25 Antennas 1241 7/24/2014 7/24/2016 SMS-200AW-72.0- 422 Florida RF SMR Cables 805 11/5/2014 11/5/2015 432 Microwave Circuits H3G020G4 Filters 264066 5/20/2015 5/20/2016 SMRE-200W-12.0- 616 Florida RF Cables SMRE Cables N/A 9/10/2014 9/10/2015 622 Rohde & Schwarz FSV40 Analyzers 101338 7/15/2015 7/15/2016 3010 Rohde & Schwarz ENV216 LISN 3010 7/10/2015 7/10/2016 RE112 Rohde & Schwarz ESIB26 Receiver 836119/012 7/16/2015 7/16/2016 ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 8

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 5 SUPPORT EQUIPMENT Table 5-1: Support Equipment Item Equipment Type Manufacturer Model Number Serial Number EUT is standalone equipment with no provisions for support equipment. 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM EUT A AC Mains A – AC Power Cable, Non-shielded, 200cm Figure 6-1: Test Setup Block Diagram ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 9

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 7 SUMMARY OF TESTS Along with the tabular data shown below, plots were taken of all signals deemed important enough to document. 7.1 Antenna Requirement – FCC 15.203 The EUT utilizes a PIFA antenna which cannot be removed without permanently damaging the device thus satisfying Part 15.203. The gain on the PIFA antenna is 6dBi. 7.2 Power Line Conducted Emissions – FCC 15.207, IC: RSS-Gen 8.8 7.2.1 Measurement Procedure ANSI C63.4 sections 6 and 7 were the guiding documents for this evaluation. Conducted emissions were performed from 150kHz to 30MHz with the spectrum analyzer’s resolution bandwidth set to 9kHz and the video bandwidth set to 30kHz. The calculation for the conducted emissions is as follows: Corrected Reading = Analyzer Reading + LISN Loss + Cable Loss Margin = Applicable Limit - Corrected Reading 7.2.2 Measurement Results Table 7.2.2-1: Conducted EMI Results – Line 1 Corrected Reading Frequency Limit Margin Correction Line (MHz) (dBuV) (dB) (dB) Quasi-Peak Average (dBuV) (dBuV) 0.152554 --- 27.53 55.85 28.32 L1 10.0 0.152554 42.91 --- 65.85 22.94 L1 10.0 0.265330 --- 21.52 51.02 29.50 L1 10.0 0.265330 31.94 --- 61.06 29.12 L1 10.0 0.301202 --- 18.67 49.97 31.30 L1 10.0 0.301202 27.95 --- 60.01 32.06 L1 10.0 0.419439 --- 4.29 47.34 43.05 L1 10.0 0.419439 20.04 --- 57.36 37.32 L1 10.0 0.450200 --- 3.84 46.80 42.96 L1 10.0 0.450200 18.00 --- 56.81 38.81 L1 10.0 1.109719 --- 13.77 46.00 32.23 L1 10.0 1.109719 18.73 --- 56.00 37.27 L1 10.0 ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 10

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 Table 7.2.2-2: Conducted EMI Results – Line 2 Corrected Reading Frequency Limit Margin Correction Line (MHz) (dBuV) (dB) (dB) Quasi-Peak Average (dBuV) (dBuV) 0.150115 --- 27.80 55.99 28.19 N 10.2 0.150115 43.09 --- 65.99 22.90 N 10.2 0.332966 --- 23.48 49.16 25.68 N 10.1 0.332966 29.59 --- 59.19 29.60 N 10.1 1.097194 --- 29.39 46.00 16.61 N 10.2 1.097194 34.61 --- 56.00 21.39 N 10.2 1.189579 --- 23.45 46.00 22.55 N 10.2 1.189579 28.58 --- 56.00 27.42 N 10.2 1.792485 --- 21.69 46.00 24.31 N 10.2 1.792485 27.28 --- 56.00 28.72 N 10.2 3.211323 --- 21.90 46.00 24.10 N 10.2 3.211323 27.35 --- 56.00 28.65 N 10.2 ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 11

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 7.3 6dB / 99% Bandwidth – FCC 15.247(a)(2), IC: RSS-247 5.2(1) 7.3.1 Measurement Procedure The 6dB bandwidth was measured in accordance with the FCC KDB 558074 D01 DTS Meas Guidance v03r03. The Resolution Bandwidth (RBW) of the spectrum analyzer was set to 100 kHz. The Video Bandwidth (VBW) was set to ≥ 3 times the RBW. The trace was set to max hold with a peak detector active. The marker-delta function of the spectrum analyzer was utilized to determine the 6 dB bandwidth of the emission. The occupied bandwidth measurement function of the spectrum analyzer was used to measure the 99% bandwidth. The span of the analyzer was set to capture all products of the modulation process, including the emission sidebands. The resolution bandwidth was set to 1% to 5% of the occupied bandwidth. The video bandwidth was set to 3 times the resolution bandwidth. A peak detector was used. 7.3.2 Measurement Results Table 7.3.2-1: 6dB / 99% Bandwidth Frequency 6dB Bandwidth 99% Bandwidth [MHz] [MHz] [MHz] 2405 1.59 2.42 2445 1.59 2.42 2475 1.59 2.42 Figure 7.3.2-1: 6dB Bandwidth Plot – 2405 MHz Figure 7.3.2-2: 6dB Bandwidth Plot – 2445 MHz ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 12

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 Figure 7.3.2-3: 6dB Bandwidth Plot – 2475 MHz Figure 7.3.2-4: 99% Bandwidth Plot – 2405 MHz Figure 7.3.2-5: 99% Bandwidth Plot – 2445 MHz Figure 7.3.2-6: 99% Bandwidth Plot – 2475 MHz ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 13

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 7.4 Fundamental Emission Output Power – FCC 15.247(b)(3), IC: RSS-247 5.4(4) 7.4.1 Measurement Procedure The maximum peak conducted output power was measured in accordance with FCC KDB 558074 D01 DTS Meas Guidance v03r03 utilizing the PKPM1 Peak power meter method. The RF output of the equipment under test was directly connected to the input of the peak power meter applying suitable attenuation. 7.4.2 Measurement Results Table 7.4.2-1: Maximum Peak Conducted Output Power Frequency Output Power (MHz) (dBm) 2405 18.34 2445 17.96 2475 14.39 ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 14

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 7.5 Emission Levels – FCC 15.247(d), 15.205, 15.209; IC RSS-247 5.5, RSS-Gen 8.9 7.5.1 Emissions into Non-restricted Frequency Bands 7.5.1.1 Measurement Procedure The unwanted emissions into non-restricted bands were measured conducted in accordance with FCC KDB 558074 D01 DTS Meas Guidance v03r03. The RF output of the equipment under test was directly connected to the input of the spectrum analyzer applying suitable attenuation. The Resolution Bandwidth (RBW) of the spectrum analyzer was set to 100 kHz. The Video Bandwidth (VBW) was set to ≥ 300 kHz. Span was set to 1.5 times the DTS bandwidth. The trace was set to max hold with a peak detector active. The resulting spectrum analyzer peak level was used to determine the reference level with respect to the 20 dBc limit. The spectrum span was then adjusted for the measurement of spurious emissions from 30MHz to 25GHz, 10 times the highest fundamental frequency. Band-edge compliance was determined using the conducted marker-delta method in which the radio frequency power that is produced by the EUT is at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of desired power. 7.5.1.2 Measurement Results Figure 7.5.1.2-1: 30 MHz – 2.5 GHz – 2405 MHz Figure 7.5.1.2-2: 2.5 GHz – 10 GHz – 2440 MHz Figure 7.5.1.2-3: 10 GHz – 25 GHz – 2475 MHz ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 15

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 Figure 7.5.1.2-4: Lower Band-edge - 2405 MHz Figure 7.5.1.2-5: Upper Band-edge - 2475 MHz ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 16

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 7.5.2 Emissions into Restricted Frequency Bands 7.5.2.1 Measurement Procedure The unwanted emissions into restricted bands were measured radiated over the frequency range of 30MHz to 25GHz, 10 times the highest fundamental frequency. The EUT was rotated through 360° and the receive antenna height was varied from 1m to 4m so that the maximum radiated emissions level would be detected. For frequencies below 1000MHz, quasi-peak measurements were made using a resolution bandwidth RBW of 120 kHz and a video bandwidth VBW of 300 kHz. For frequencies above 1000MHz, peak and average measurements were made with RBW and VBW of 1 MHz and 3 MHz respectively. The average emissions were further corrected by applying the duty cycle correction of the EUT for comparison to the average limit. Each emission found to be in a restricted band as defined by section 15.205, including any emission at the operational band-edge, was compared to the radiated emission limits as defined in section 15.209. 7.5.2.2 Duty Cycle Correction For average radiated measurements, using a 66% duty cycle, the measured level was reduced by a factor -3.61dB. The duty cycle correction factor is determined using the formula: 20log (66/100) = - 3.61dB. A detailed analysis of the duty cycle timing is provided in the Theory of Operation accompanying the application for certification. 7.5.2.3 Measurement Results Table 7.5.2.3-1: Radiated Spurious Emissions Tabulated Data Level Antenna Correction Corrected Level Limit Margin Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 2405 MHz 2390 55.35 47.12 H 0.14 55.49 43.65 74.0 54.0 18.5 10.4 2390 48.67 40.01 V 0.14 48.81 36.54 74.0 54.0 25.2 17.5 4810 43.52 32.11 H 7.89 51.41 36.39 74.0 54.0 22.6 17.6 4810 45.74 35.54 V 7.89 53.63 39.82 74.0 54.0 20.4 14.2 12025 41.15 30.33 H 20.94 62.09 47.66 83.5 63.5 21.4 15.9 12025 41.98 30.10 V 20.94 62.92 47.43 83.5 63.5 20.6 16.1 2440 MHz 4880 43.16 32.29 H 8.11 51.27 36.79 74.0 54.0 22.7 17.2 4880 45.06 35.34 V 8.11 53.17 39.84 74.0 54.0 20.8 14.2 12200 40.15 28.68 H 21.98 62.13 47.06 83.5 63.5 21.4 16.5 12200 42.45 32.11 V 21.98 64.43 50.49 83.5 63.5 19.1 13.1 2475 MHz 2483.5 60.70 52.98 H 0.69 61.39 50.06 74.0 54.0 12.6 3.9 2483.5 55.09 47.22 V 0.69 55.78 44.30 74.0 54.0 18.2 9.7 4950 43.10 31.45 H 8.34 51.44 36.18 74.0 54.0 22.6 17.8 4950 43.21 31.91 V 8.34 51.55 36.64 74.0 54.0 22.5 17.4 ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 17

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 7.5.2.4 Sample Calculation: RC = RU + CFT Where: CFT = Total Correction Factor (AF+CA+AG)-DC (Average Measurements Only) RU = Uncorrected Reading RC = Corrected Level AF = Antenna Factor CA = Cable Attenuation AG = Amplifier Gain DC = Duty Cycle Correction Factor Example Calculation: Peak Corrected Level: 55.35 + 0.14 = 55.49dBuV/m Margin: 74.0dBuV/m – 55.49dBuV/m = 18.5dB Example Calculation: Average Corrected Level: 47.12 + 0.14 - 3.61 = 43.65dBuV Margin: 54.0dBuV – 43.65dBuV = 10.4dB ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 18

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 7.6 Maximum Power Spectral Density in the Fundamental Emission – FCC 15.247(e) IC: RSS-247 5.2(2) 7.6.1 Measurement Procedure The power spectral density was measured in accordance with the FCC KDB 558074 D01 DTS Meas Guidance v03r03 utilizing the PKPSD (peak PSD) method. The RF output of the equipment under test was directly connected to the input of the spectrum analyzer applying suitable attenuation. The Resolution Bandwidth (RBW) of the spectrum analyzer was set to 3 kHz. The Video Bandwidth (VBW) was set to 10 kHz. Span was set to 1.5 times the DTS bandwidth. The trace was set to max hold with a peak detector active. 7.6.2 Measurement Results Table 7.6.2-1: Peak Power Spectral Density Frequency PSD Level (MHz) (dBm) 2405 3.52 2445 3.32 2475 0.44 Figure 7.6.2-1: PSD Plot – 2405 MHz Figure 7.6.2-2: PSD Plot – 2445 MHz Figure 7.6.2-3: PSD Plot – 2475 MHz ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 19

Model: G5 Integrated Focus AXe FCC ID: R7PEG1R1S6 IC: 5294A-EG1R1S6 8 CONCLUSION In the opinion of ACS, Inc. the G5 Integrated Focus AXe, manufactured by Landis+Gyr Technology, Inc. meets the requirements of FCC Part 15 subpart C and Industry Canada’s Radio Standards Specification RSS-247. END REPORT ACS Report: 15-0242.W06.2A Advanced Compliance Solutions Page 20


Document Created: 2015-10-12 16:41:37
Document Modified: 2015-10-12 16:41:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC