TEST REPORT

FCC ID: R7PEC1R2S4

Test Report

Download: PDF
FCCID_826786

Certification Test Report Frequency Hopping Spread Spectrum Transmitter FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 07-0269 Manufacturer: Cellnet Technology, Inc. Model: L+G S4e 2G Utilinet Endpoint Test Begin Date: June 19, 2007 Test End Date: June 19, 2007 Report Issue Date: July 2, 2007 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612-0 This report is not be used to claim certification, approval, or endorsement by NVLAP, NIST or any government agency. Prepared by: Reviewed by: J. Kirby Munroe R. Sam Wismer Manager Wireless Certifications Engineering Manager ACS, Inc. ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 22 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Table of Contents 1.0 General 3 1.1 Purpose 3 1.2 Product Description 3 1.2.1 General 3 1.2.2 Intended Use 3 1.3 Test Methodology and Considerations 3 2.0 Test Facilities 3 2.1 Location 3 2.2 Laboratory Accreditations/Recognitions/Certifications 3 2.3 Radiated Emissions Test Site Description 5 2.3.1 Semi-Anechoic Chamber Test Site 5 2.3.2 Open Area Tests Site (OATS) 6 2.4 Conducted Emissions Test Site Description 7 3.0 Applicable Standards and References 7 4.0 List of Test Equipment 8 5.0 Support Equipment 9 6.0 EUT Setup Block Diagram 9 7.0 Summary of Tests 10 7.1 Antenna Requirement 10 7.2 Power Line Conducted Emissions 10 7.2.1 Test Methodology 10 7.2.2 Test Results 10 7.3 Radiated Emissions (Unintentional Radiation) 11 7.3.1 Test Methodology 11 7.3.2 Test Results 11 7.4 Peak Output Power 11 7.4.1 Test Methodology 11 7.4.2 Test Results 11 7.5 Channel Usage 13 7.5.1 Carrier Frequency Separation 13 7.5.1.1 Test Methodology 13 7.5.1.2 Test Results 13 7.5.2 Number of Hopping Channels 14 7.5.3 Channel Dwell Time 15 7.5.4 20dB Bandwidth 15 7.5.4.1 Test Methodology 15 7.5.4.2 Test Results 15 7.6 Band-edge Compliance and Spurious Emissions 17 7.6.1 Band-edge Compliance of RF Conducted Emissions 17 7.6.1.1 Test Methodology 17 7.6.1.2 Test Results 17 7.6.2 RF Conducted Spurious Emissions 18 7.6.2.1 Test Methodology 18 7.6.2.2 Test Results 18 7.6.3 Radiated Spurious Emissions (Transmitter) 20 7.6.3.1 Test Methodology 20 7.6.3.2 Test Results 21 7.6.3.3 Sample Calculations 22 8.0 CONCLUSION 22 Additional Exhibits Included In Filing Internal Photographs Theory of Operation Test Setup Photographs BOM (Parts List) Product Labeling System Block Diagram RF Exposure – MPE Calculations Schematics Installation/Users Guide 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 1.0 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15, Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification RSS-210. 1.2 Product Description 1.2.1 General The L+G S4e 2G Utilinet Endpoint module was designed for integration into the Landis + Gyr S4e 2G meter. With the addition of the L+G S4e 2G Utilinet Endpoint module, this meter is enabled for deployment in the UtiliNet AMR system, allowing electric meter data access over the UtiliNet frequency hopping spread spectrum (FHSS) fixed mesh network. The network operates in the 900MHz ISM band (902~928MHz), with a typical RF output power of +22dBm. Manufacturer Information: Cellnet Technology, Inc. 30000 Mill Creek Avenue Suite 100 Alpharetta, GA 30022 USA Detailed photographs of the EUT are filed separately with this filing. 1.2.2 Intended Use The L+G S4e 2G Utilinet Endpoint module was designed for integration into the Landis + Gyr S4e 2G meter. 1.3 Test Methodology and Considerations The L+G S4e 2G Utilinet Endpoint is a module designed to be integrated into a host device therefore testing was performed on the module in a stand-alone configuration with the exception of AC power line conducted emissions. AC power line conducted emissions were performed with the module installed into a typical host device (electric meter). ACS Report: 07-0269 Advanced Compliance Solutions Page 3

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 2.0 TEST FACILITIES 2.1 Location The radiated and conducted emissions test sites are located at the following address: Advanced Compliance Solutions 5015 B.U. Bowman Drive Buford, GA 30518 Phone: (770) 831-8048 Fax: (770) 831-8598 2.2 Laboratory Accreditations/Recognitions/Certifications The Semi-Anechoic Chamber Test Site, Open Area Test Site (OATS) and Conducted Emissions Site have been fully described, submitted to, and accepted by the FCC, Industry Canada and the Japanese Voluntary Control Council for Interference by information technology equipment. In addition, ACS is compliant to ISO 17025 as certified by the National Institute of Standards and Technology under their National Voluntary Laboratory Accreditation Program. The following certification numbers have been issued in recognition of these accreditations and certifications: FCC Registration Number: 89450 Industry Canada Lab Code: IC 4175 VCCI Member Number: 1831 ƒ VCCI OATS Registration Number R-1526 ƒ VCCI Conducted Emissions Site Registration Number: C-1608 NVLAP Lab Code: 200612-0 ACS Report: 07-0269 Advanced Compliance Solutions Page 4

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 2.3 Radiated Emissions Test Site Description 2.3.1 Semi-Anechoic Chamber Test Site The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid is 101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on steel panels and installed directly on the inner walls of the chamber. The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The chamber is grounded via 1 - 8’ copper ground rod, installed at the center of the back wall, it is bound to the ground plane using 3/4" stainless steel braided cable. The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely operated from inside the control room located 25’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Behind the turntable is a 3’ x 6’ x 4’ deep shielded pit used for support equipment if necessary. The pit is equipped with 1 - 4” PVC chases from the turntable to the pit that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. A diagram of the Semi-Anechoic Chamber Test Site is shown in Figure 2.3-1 below: 3 Meters 5 Feet Diamete r 20 Feet 30 Feet Figure 2.3-1: Semi-Anechoic Chamber Test Site ACS Report: 07-0269 Advanced Compliance Solutions Page 5

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 2.3.2 Open Area Tests Site (OATS) The open area test site consists of a 40’ x 66’ concrete pad covered with a perforated electro-plated galvanized sheet metal. The perforations in the sheet metal are 1/8” holes that are staggered every 3/16”. The individual sheets are placed to overlap each other by 1/4” and are riveted together to provide a continuous seam. Rivets are spaced every 3” in a 3 x 20 meter perimeter around the antenna mast and EUT area. Rivets in the remaining area are spaced as necessary to properly secure the ground plane and maintain the electrical continuity. The entire ground plane extends 12’ beyond the turntable edge and 16’ beyond the antenna mast when set to a 10 meter measurement distance. The ground plane is grounded via 4 - 8’ copper ground rods, each installed at a corner of the ground plane and bound to the ground plane using 3/4" stainless steel braided cable. The turntable is an all aluminum 10’ flush mounted table installed in an all aluminum frame. The table is remotely operated from inside the control room located 40’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Adjacent to the turntable is a 7’ x 7’ square and 4’ deep concrete pit used for support equipment if necessary. The pit is equipped with 5 - 4” PVC chases from the pit to the control room that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. The pit is covered with 2 sheets of 1/4" diamond style re- enforced steel sheets. The sheets are painted to match the perforated steel ground plane; however the underside edges have been masked off to maintain the electrical continuity of the ground plane. All reflecting objects are located outside of the ellipse defined in ANSI C63.4. A diagram of the Open Area Test Site is shown in Figure 2.3-2 below: 10 3 Meters 40 7x7x4 Pit 66 Feet Figure 2.3-2: Open Area Test Site ACS Report: 07-0269 Advanced Compliance Solutions Page 6

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 2.4 Conducted Emissions Test Site Description The AC mains conducted EMI site is located in the main EMC lab. It consists of an 8’ x 8’ solid aluminum horizontal group reference plane (GRP) bonded every 3” to an 8’ X 8’ vertical ground plane. The site is of sufficient size to test table top and floor standing equipment in accordance with section 6.1.4 of ANSI C63.4. A diagram of the room is shown below in figure 4.1.3-1: Vertical Ground Plane (8’ x 8’) Non-Conductive EUT Table (1m x 1.5m x .8m) .4 Meters .8 Meters Horizontal Ground Plane (8’ x 8’) LISN Figure 2.4-1: AC Mains Conducted EMI Site 3.0 APPLICABLE STANDARD REFERENCES The following standards were used: ™ ANSI C63.4-2003: Method of Measurements of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the 9KHz to 40GHz ™ US Code of Federal Regulations (CFR): Title 47, Part 2, Subpart J: Equipment Authorization Procedures, 2006 ™ US Code of Federal Regulations (CFR): Title 47, Part 15, Subpart C: Radio Frequency Devices, Intentional Radiators, 2006 ™ FCC OET Bulletin 65 Appendix C - Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields, 2001 ™ FCC Public Notice DA 00-705 - Filing and Measurement Guidelines for Frequency Hopping Spread Spectrum Systems, March 30, 2000 ™ Industry Canada Radio Standards Specification: RSS-210 - Low-power License-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment ACS Report: 07-0269 Advanced Compliance Solutions Page 7

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 4.0 LIST OF TEST EQUIPMENT All test equipment used for regulatory testing is calibrated yearly or according to manufacturer’s specifications. Table 4.0-1: Test Equipment Equipment Calibration Information Serial Equipment Asset ID Manufacturer Model Number Number Type Cal Due 22 Agilent 8449B 3008A00526 Amplifiers 04/10/08 338 Hewlett Packard 8449B 3008A01111 Amplifiers 09/26/07 25 Chase CBL6111 1043 Antennas 06/06/08 30 Spectrum Technologies DRH-0118 970102 Antennas 05/10/08 329 A.H.Systems SAS-571 721 Antennas 08/24/07 340 Aeroflex/Weinschel AS-20 7136 Attenuators 08/29/07 SMS-290AW- 344 Florida RF Cables 480.0-SMR N/A Cables 12/21/07 SMRE-200W-12.0- 343 Florida RF Cables SMRE N/A Cables 12/21/07 SMSE-200-72.0- 290 Florida RF Cables SMRE None Cables 05/15/08 SMRE-200W-12.0- 291 Florida RF Cables SMRE None Cables 05/15/08 SMR-290AW- 292 Florida RF Cables 480.0-SMR None Cables 05/24/08 337 Microwave Circuits H1G513G1 282706 Filters 10/03/07 153 EMCO 3825/2 9411-2268 LISN 11/16/07 152 EMCO 3825/2 9111-1905 LISN 02/20/08 Spectrum 283 Rohde & Schwarz FSP40 1000033 Analyzers 11/09/08 Spectrum 2 Rohde & Schwarz ESMI-Receiver 839587/003 Analyzers 03/05/08 Spectrum 1 Rohde & Schwarz ESMI - Display 833771/007 Analyzers 03/05/08 73 Agilent 8447D 2727A05624 Amplifiers 05/09/08 16 ACS Cable 16 Cables 05/21/08 ACS Report: 07-0269 Advanced Compliance Solutions Page 8

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 5.0 SUPPORT EQUIPMENT Table 5-1: Support Equipment Equipment Type Manufacturer Model Number Serial Number FCC ID Electric Meter Landis+Gyr AXRS4e NA NA * The equipment listed above was utilized in support of AC Power Conducted Emissions testing where installation into a typical host device was required. 6.0 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM Spectrum DC Power Analyzer EUT Supply Used for RF conducted measurements only. Figure 6-1: EUT Test Setup The EUT was integrated into a typical host (electric meter) for the purpose of AC power line conducted emissions. The host equipment is detailed in Section 5.0 above. *See Test Setup photographs for additional detail. ACS Report: 07-0269 Advanced Compliance Solutions Page 9

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.0 SUMMARY OF TESTS Along with the tabular data shown below, plots were taken of all signals deemed important enough to document. 7.1 Antenna Requirement A 50-ohm MCX connector is utilized to efficiently couple the RF energy into the flex dipole antenna (Landis_Gyr part number 71654). It has a typical gain of 2 dBi. 7.2 Power Line Conducted Emissions 7.2.1 Test Methodology ANSI C63.4 sections 6 and 7 were the guiding documents for this evaluation. Conducted emissions were performed from 150kHz to 30MHz with the spectrum analyzer’s resolution bandwidth set to 9kHz and the video bandwidth set to 30kHz. The calculation for the conducted emissions is as follows: Corrected Reading = Analyzer Reading + LISN Loss + Cable Loss Margin = Applicable Limit - Corrected Reading The L+G S4e 2G Utilinet Endpoint module was installed in a typical host device. The host device is detailed in Section 5.0. 7.2.2 Test Results Results of the test are shown below in and Tables 7.2-1. Table 7.2-1: Line 1 Conducted EMI Results Uncorrected Reading Total Correction Corrected Level Limit Margin Frequency (dBuV) Factor (dBuV) (dBuV) (dB) Line (MHz) (dB) Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Line 1 0.17 45.4 35.9 9.80 55.20 45.70 64.96 54.96 9.8 9.3 FLO 0.2 40.5 31.7 9.80 50.30 41.50 63.61 53.61 13.3 12.1 FLO 0.27 34.1 27.7 9.80 43.90 37.50 61.12 51.12 17.2 13.6 FLO 0.3 30.2 21 9.80 40.00 30.80 60.24 50.24 20.2 19.4 FLO 3.96 23.3 16 9.80 33.10 25.80 56.00 46.00 22.9 20.2 FLO 19.98 21.8 19.9 10.12 31.92 30.02 60.00 50.00 28.1 20.0 FLO Line 2 0.17 44.9 35.7 9.80 54.70 45.50 64.96 54.96 10.3 9.5 FLO 0.2 40.2 31.7 9.80 50.00 41.50 63.61 53.61 13.6 12.1 FLO 0.27 34 27.6 9.80 43.80 37.40 61.12 51.12 17.3 13.7 FLO 0.34 28.9 19.1 9.80 38.70 28.90 59.20 49.20 20.5 20.3 FLO 0.39 24.1 6.8 9.80 33.90 16.60 58.06 48.06 24.2 31.5 FLO 19.98 22.7 20.4 10.12 32.82 30.52 60.00 50.00 27.2 19.5 FLO ACS Report: 07-0269 Advanced Compliance Solutions Page 10

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.3 Radiated Emissions (Unintentional Radiation) 7.3.1 Test Methodology Radiated emission tests were performed over the frequency range of 30MHz to 5 GHz. Measurements of the radiated field strength were made at a distance of 3m from the boundary of the equipment under test (EUT) and the receiving antenna. The antenna height was varied from 1m to 4m so that the maximum radiated emissions level would be detected. For frequencies from 30MHz to 1000MHz, radiated measurements were made with a Quasi-peak detector and the spectrum analyzer’s resolution bandwidth set to 120 KHz. For measurements above 1000MHz, peak measurements were made with the RBW and VBW set to 1MHz and 3MHz respectively and average measurements with the RBW and VBW set to 1MHz and 10 Hz respectively. 7.3.2 Test Results Results of the test are given in Table 7.3-1 below: Table 7.3-1: Radiated Emissions Tabulated Data Level Antenna Correction Corrected Level Limit Margin Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 30 21.33 H -6.70 --------- 14.63 -------- 40.0 --------- 25.37 159.333 21.81 H -14.39 --------- 7.42 -------- 43.5 --------- 36.08 349 22.04 H -9.06 --------- 12.98 -------- 46.0 --------- 33.02 495.6 23.11 H -5.63 --------- 17.48 -------- 46.0 --------- 28.52 672.355 22.22 V -2.03 --------- 20.19 -------- 46.0 --------- 25.81 942.877 21.81 V 2.47 --------- 24.28 -------- 46.0 --------- 21.72 * Note: All emissions above 942.88 MHz were attenuated below the permissible limit. 7.4 Peak Output Power 7.4.1 Test Methodology (Conducted Method) The 20dB bandwidth of the EUT was within the resolution bandwidth of spectrum analyzer, therefore the power measurement was made using the spectrum analyzer method. The resolution and video bandwidth were set to > 20 dB bandwidth of the emission measured. The device employs >50 channels therefore the power is limited to 1 Watt. 7.4.2 Test Results Results are shown in table 7.4-1 and the worst case was plotted and shown in figure 7.4-1 to 7.4-3 below: Table 7.4-1: RF Output Power Frequency Level [MHz] [dBm] 902.1 22.44 915 22.55 927.9 22.63 ACS Report: 07-0269 Advanced Compliance Solutions Page 11

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 * RBW 1 MHz Marker 1 [T1 ] VBW 3 MHz 22.44 dBm Ref 30 dBm Att 50 dB SWT 2.5 ms 902.104000000 MHz 30 Offset 10 dB 1 B 20 1 PK MAXH 10 LVL 0 -10 -20 -30 -40 -50 -60 -70 Center 902.1 MHz 200 kHz/ Span 2 MHz D at e: 1 9. J UN .2 00 7 1 6 :0 1: 52 Figure 7.4-1: Output power – Low Channel * RBW 1 MHz Marker 1 [T1 ] VBW 3 MHz 22.55 dBm Ref 30 dBm Att 50 dB SWT 2.5 ms 915.024000000 MHz 30 Offset 10 dB 1 B 20 1 PK MAXH 10 LVL 0 -10 -20 -30 -40 -50 -60 -70 Center 915 MHz 200 kHz/ Span 2 MHz Date: 19.JUN.2007 15:44:07 Figure 7.4-2: Output power – Mid Channel * RBW 1 MHz Marker 1 [T1 ] VBW 3 MHz 22.63 dBm Ref 30 dBm Att 50 dB SWT 2.5 ms 927.900000000 MHz 30 Offset 10 dB 1 B 20 1 PK MAXH 10 LVL 0 -10 -20 -30 -40 -50 -60 -70 Center 927.9 MHz 200 kHz/ Span 2 MHz D at e: 1 9. J UN .2 00 7 1 5 :5 4: 47 Figure 7.4-3: Output power – High Channel ACS Report: 07-0269 Advanced Compliance Solutions Page 12

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.5 Channel Usage Requirements FCC 15.247(a)(1): Frequency hopping systems shall have hopping channel carrier frequencies separated by a minimum of 25 kHz or the 20 dB bandwidth of the hopping channel, whichever is greater. The system shall hop to channel frequencies that are selected at the system hopping rate from a pseudo randomly ordered list of hopping frequencies. Each frequency must be used equally on the average by each transmitter. The system receivers shall have input bandwidths that match the hopping channel bandwidths of their corresponding transmitters and shall shift frequencies in synchronization with the transmitted signals. FCC 15.247(a) (1) (i): For frequency hopping systems operating in the 902–928 MHz band: if the 20 dB bandwidth of the hopping channel is less than 250 kHz, the system shall use at least 50 hopping frequencies and the average time of occupancy on any frequency shall not be greater than 0.4 seconds within a 20 second period; if the 20 dB bandwidth of the hopping channel is 250 kHz or greater, the system shall use at least 25 hopping frequencies and the average time of occupancy on any frequency shall not be greater than 0.4 seconds within a 10 second period. The maximum allowed 20 dB bandwidth of the hopping channel is 500 kHz. 7.5.1 Carrier Frequency Separation 7.5.1.1 Test Methodology The span of the spectrum analyzer was set wide enough to capture two adjacent peaks and the RBW and VBW were set to ≥ 1% of the span. 7.5.1.2 Test Results The maximum 20dB bandwidth of the hopping channel was measured to be 27.9kHz (See figure 7.5.4-1 to 7.5.4-3 below). The adjacent channel separation was measured to be 100kHz. Results are shown in figure 7.5.1-1 below: * RBW 10 kHz Delta 1 [T1 ] VBW 30 kHz -0.02 dB Ref 40 dBm Att 60 dB SWT 2.5 ms 100.000000000 kHz 40 Offset 10 dB Marker 1 [T1 ] 22.84 dBm * 902.101200000 MHz B 30 1 PK 1 1 VIEW 20 LVL 10 0 -10 -20 -30 -40 -50 -60 Center 902.15 MHz 20 kHz/ Span 200 kHz Date: 19.JUN.200 7 16:17:59 Figure 7.5.1-1: Carrier Frequency Separation ACS Report: 07-0269 Advanced Compliance Solutions Page 13

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.5.2 Number of Hopping Channels The 20dB bandwidth of the device is less than 250 kHz. The device employs at least 50 hopping channels as required. The actual number of hopping channels is 240. The channel hopping sequence table is shown in Table 7.5.2-1 below: Table 7.5.2-1: Number of Hopping Channels Channel Freq (MHz) Channel Freq (MHz) Channel Freq (MHz) Channel Freq (MHz) Channel Freq (MHz) 86 910.6 69 908.9 252 927.2 214 923.4 208 922.8 211 923.1 256 927.6 200 922 28 904.8 84 910.4 173 919.3 176 919.6 185 920.5 158 917.8 21 904.1 141 916.1 52 907.2 36 905.6 77 909.7 121 914.1 72 909.2 134 915.4 131 915.1 124 914.4 125 914.5 166 918.6 242 926.2 32 905.2 61 908.1 81 910.1 63 908.3 228 924.8 22 904.2 147 916.7 165 918.5 23 904.3 187 920.7 235 925.5 191 921.1 95 911.5 180 920 82 910.2 222 924.2 150 917 182 920.2 227 924.7 174 919.4 108 912.8 171 919.1 122 914.2 40 906 230 925 99 911.9 41 906.1 229 924.9 144 916.4 241 926.1 126 914.6 188 920.8 216 923.6 33 905.3 133 915.3 152 917.2 89 910.9 253 927.3 195 921.5 169 918.9 193 921.3 220 924 204 922.4 154 917.4 30 905 254 927.4 127 914.7 70 909 190 921 136 915.6 146 916.6 20 904 44 906.4 236 925.6 178 919.8 34 905.4 217 923.7 259 927.9 149 916.9 210 923 49 906.9 114 913.4 240 926 143 916.3 71 909.1 255 927.5 111 913.1 48 906.8 181 920.1 205 922.5 129 914.9 213 923.3 66 908.6 232 925.2 192 921.2 209 922.9 35 905.5 79 909.9 123 914.3 85 910.5 94 911.4 42 906.2 132 915.2 233 925.3 53 907.3 140 916 172 919.2 245 926.5 38 905.8 202 922.2 83 910.3 25 904.5 120 914 118 913.8 37 905.7 257 927.7 59 907.9 67 908.7 60 908 43 906.3 237 925.7 87 910.7 183 920.3 201 922.1 54 907.4 135 915.5 168 918.8 248 926.8 198 921.8 243 926.3 234 925.4 196 921.6 78 909.8 116 913.6 64 908.4 92 911.2 223 924.3 80 910 91 911.1 68 908.8 57 907.7 24 904.4 93 911.3 212 923.2 100 912 109 912.9 225 924.5 184 920.4 221 924.1 239 925.9 249 926.9 103 912.3 74 909.4 96 911.6 29 904.9 215 923.5 151 917.1 153 917.3 157 917.7 177 919.7 179 919.9 203 922.3 65 908.5 247 926.7 139 915.9 258 927.8 197 921.7 159 917.9 167 918.7 117 913.7 186 920.6 219 923.9 142 916.2 224 924.4 148 916.8 244 926.4 97 911.7 58 907.8 246 926.6 75 909.5 189 920.9 51 907.1 164 918.4 238 925.8 206 922.6 31 905.1 98 911.8 163 918.3 46 906.6 226 924.6 73 909.3 45 906.5 90 911 39 905.9 155 917.5 130 915 156 917.6 106 912.6 251 927.1 47 906.7 194 921.4 101 912.1 145 916.5 115 913.5 62 908.2 162 918.2 50 907 76 909.6 128 914.8 138 915.8 119 913.9 27 904.7 199 921.9 110 913 231 925.1 107 912.7 207 922.7 160 918 113 913.3 88 910.8 250 927 56 907.6 137 915.7 175 919.5 102 912.2 26 904.6 55 907.5 170 919 112 913.2 161 918.1 105 912.5 218 923.8 104 912.4 ACS Report: 07-0269 Advanced Compliance Solutions Page 14

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.5.3 Channel Dwell Time The maximum duration of the RF transmission is 364ms during a 700ms channel dwell time. There is a minimum of 50 channels used during the hopping sequence therefore a channel will not be re-occupied until at least 35s. Therefore the average time of occupancy on any one channel in a 20 second period is 364ms. A detailed description of the RF timing and a timing diagram are included in the theory of operation. 7.5.4 20dB Bandwidth 7.5.4.1 Test Methodology The spectrum analyzer span was set to 2 to 3 times the estimated 20 dB bandwidth of the emission. The RBW was to ≥ 1% of the estimated 20 dB bandwidth. The trace was set to max hold with a peak detector active. The Delta function of the analyzer was utilized to determine the 20 dB bandwidth of the emission. The span and RBW were examined and re-adjusted if necessary to meet the requirements of 2 to 3 times the 20 bandwidth for the span and ≥ 1% of the 20 dB bandwidth for the RBW. 7.5.4.2 Test Results The maximum 20dB bandwidth was found to be approximately 27.9kHz. Results are shown below in Table 7.5.4-1 and Figures 7.5.4-1 through 7.5.4-3. Table 7.5.4-1 Frequency 20dB Bandwidth (MHz) (kHz) 902.1 27.3 915 27.3 927.9 27.9 * RBW 3 kHz Marker 1 [T1 ] VBW 10 kHz 22.58 dBm Ref 30 dBm Att 50 dB SWT 10 ms 902.095350000 MHz 30 Offset 10 dB ndB [T1] 20.00 dB 1 BW 27.300000000 kHz Temp 1 [T1 ndB] B 20 2.93 dBm 1 PK 902.086950000 MHz MAXH 10 Temp 2 [T1 ndB] T1 T2 2.44 dBm LVL 902.114250000 MHz 0 -10 -20 -30 -40 -50 -60 -70 Center 902.1 MHz 7.5 kHz/ Span 75 kHz Date: 19.JUN.200 7 15:38:32 Figure 7.5.4-1: 20dB Bandwidth Low Channel ACS Report: 07-0269 Advanced Compliance Solutions Page 15

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 * RBW 3 kHz Marker 1 [T1 ] VBW 10 kHz 22.73 dBm Ref 30 dBm Att 50 dB SWT 10 ms 914.995200000 MHz 30 Offset 10 dB ndB [T1] 20.00 dB 1 BW 27.300000000 kHz Temp 1 [T1 ndB] B 20 2.68 dBm 1 PK 914.986650000 MHz MAXH 10 Temp 2 [T1 ndB] T1 T2 2.72 dBm LVL 915.013950000 MHz 0 -10 -20 -30 -40 -50 -60 -70 Center 915 MHz 7.5 kHz/ Span 75 kHz Date: 19.JUN.200 7 15:47:01 Figure 7.5.4-2: 20dB Bandwidth Mid Channel * RBW 3 kHz Marker 1 [T1 ] VBW 10 kHz 22.80 dBm Ref 30 dBm Att 50 dB SWT 10 ms 927.895350000 MHz 30 Offset 10 dB ndB [T1] 20.00 dB 1 BW 27.900000000 kHz Temp 1 [T1 ndB] B 20 2.71 dBm 1 PK 927.886650000 MHz MAXH 10 Temp 2 [T1 ndB] T1 T2 2.22 dBm LVL 927.914550000 MHz 0 -10 -20 -30 -40 -50 -60 -70 Center 927.9 MHz 7.5 kHz/ Span 75 kHz Date: 19.JUN.200 7 15:52:39 Figure 7.5.4-3: 20dB Bandwidth High Channel ACS Report: 07-0269 Advanced Compliance Solutions Page 16

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.6 Band-Edge Compliance and Spurious Emissions 7.6.1 Band-Edge Compliance of RF Conducted Emissions 7.6.1.1 Test Methodology The EUT was investigated at the lowest and highest channel available to determine band-edge compliance. For each measurement the spectrum analyzer’s RBW was set to 30 kHz, which is ≥ 1% of the span, and the VBW was set to 100kHz. 7.6.1.2 Test Results Band-edge compliance is displayed in Figures 7.6.1-1 and 7.6.2-2 * RBW 30 kHz Delta 1 [T1 ] VBW 100 kHz 53.13 dB Ref 30 dBm Att 50 dB SWT 2.5 ms 104.000000000 kHz 30 Offset 10 dB Marker 1 [T1 ] 1 -30.68 dBm 902.000000000 MHz B 20 1 PK MAXH 10 LVL 0 -10 -20 1 -30 -40 -50 -60 -70 Center 902 MHz 100 kHz/ Span 1 MHz Date: 19.JUN.200 7 15:40:52 Figure 7.6.1-1: Lower Band-edge * RBW 30 kHz Delta 1 [T1 ] VBW 100 kHz 52.28 dB Ref 30 dBm Att 50 dB SWT 2.5 ms -100.000000000 kHz 30 Offset 10 dB Marker 1 [T1 ] 1 -29.37 dBm 928.000000000 MHz B 20 1 PK MAXH 10 LVL 0 -10 -20 1 -30 -40 -50 -60 -70 Center 928 MHz 200 kHz/ Span 2 MHz Date: 19.JUN.200 7 15:55:59 Figure 7.6.1-2: Upper Band-edge ACS Report: 07-0269 Advanced Compliance Solutions Page 17

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.6.2 RF Conducted Spurious Emissions 7.6.2.1 Test Methodology The EUT was investigated for conducted spurious emissions from 30MHz to 10GHz, 10 times the highest fundamental frequency. Measurements were made at the low, center and high channels of the EUT. For each measurement, the spectrum analyzer’s RBW was set to 100kHz. A peak detector function was used with the trace set to max hold. 7.6.2.1 Test Results All emission found were greater than 20dB down from the fundamental carrier. Results are shown below in Figure 7.6.2-1 through 7.6.2-6. * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 22.32 dBm Ref 30 dBm Att 50 dB SWT 100 ms 903.000000000 MHz 30 Offset 10 dB 1 A 20 1 PK MAXH 10 LVL D1 2.32 dBm 0 -10 -20 -30 -40 -50 -60 -70 Start 30 MHz 97 MHz/ Stop 1 GHz Date: 19.JUN.200 7 15:33:16 Figure 7.6.2-1 RF Conducted Spurious Emissions – Low Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -24.10 dBm Ref 30 dBm Att 50 dB SWT 900 ms 7.084000000 GHz 30 Offset 10 dB A 20 1 PK MAXH 10 LVL D1 2.32 dBm 0 -10 -20 1 -30 -40 -50 -60 -70 Start 1 GHz 900 MHz/ Stop 10 GHz Date: 19.JUN.200 7 15:33:49 Figure 7.6.2-2 RF Conducted Spurious Emissions – Low Channel ACS Report: 07-0269 Advanced Compliance Solutions Page 18

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 22.48 dBm Ref 30 dBm Att 50 dB SWT 100 ms 916.580000000 MHz 30 Offset 10 dB 1 A 20 1 PK MAXH 10 LVL D1 2.48 dBm 0 -10 -20 -30 -40 -50 -60 -70 Start 30 MHz 97 MHz/ Stop 1 GHz Date: 19.JUN.200 7 15:45:00 Figure 7.6.2-3 RF Conducted Spurious Emissions – Mid Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -23.76 dBm Ref 30 dBm Att 50 dB SWT 900 ms 7.138000000 GHz 30 Offset 10 dB A 20 1 PK MAXH 10 LVL D1 2.48 dBm 0 -10 -20 1 -30 -40 -50 -60 -70 Start 1 GHz 900 MHz/ Stop 10 GHz Date: 19.JUN.200 7 15:45:47 Figure 7.6.2-4 RF Conducted Spurious Emissions – Mid Channel ACS Report: 07-0269 Advanced Compliance Solutions Page 19

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 22.53 dBm Ref 30 dBm Att 50 dB SWT 100 ms 930.160000000 MHz 30 Offset 10 dB 1 A 20 1 PK MAXH 10 LVL D1 2.53 dBm 0 -10 -20 -30 -40 -50 -60 -70 Start 30 MHz 97 MHz/ Stop 1 GHz Date: 19.JUN.200 7 15:53:27 Figure 7.6.2-5 RF Conducted Spurious Emissions – High Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -24.51 dBm Ref 30 dBm Att 50 dB SWT 900 ms 7.138000000 GHz 30 Offset 10 dB A 20 1 PK MAXH 10 LVL D1 2.53 dBm 0 -10 -20 1 -30 -40 -50 -60 -70 Start 1 GHz 900 MHz/ Stop 10 GHz Date: 19.JUN.200 7 15:54:18 Figure 7.6.2-6 RF Conducted Spurious Emissions – High Channel 7.6.3 Radiated Spurious Emissions (Transmitter) 7.6.3.1 Test Methodology Radiated emissions tests were made over the frequency range of 30MHz to 10GHz, 10 times the highest fundamental frequency. The EUT was rotated through 360° and the receive antenna height was varied from 1m to 4m so that the maximum radiated emissions level would be detected. For frequencies below 1000MHz, quasi-peak measurements were made using a resolution bandwidth (RBW) of 120 kHz and a video bandwidth (VBW) of 300 kHz. For frequencies above 1000MHz, average measurements were made using an RBW of 1 MHz and a VBW of 10 Hz and peak measurements were made with RBW of 1 MHz and a VBW of 1 MHz. The EUT was caused to generate a continuous carrier signal on the hopping channel. ACS Report: 07-0269 Advanced Compliance Solutions Page 20

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.6.3.2 Test Results Radiated spurious emissions found in the band of 30MHz to 10GHz are reported in Table 7.6.3-1. through 7.6.3-3. Each emission found to be in a restricted band as defined by section 15.205, was compared to the radiated emission limits as defined in section 15.209. Table 7.6.3-1: Radiated Spurious Emissions – Low Channel Level (dBuV) Antenna Correction Corrected Level Limit Margin Frequency Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 2706.3 49.32 39.74 H -5.24 44.08 34.50 74.0 54.0 29.92 19.50 2706.3 47.22 34.78 V -5.50 41.72 29.28 74.0 54.0 32.28 24.72 3608.4 51.27 41.93 H -2.38 48.89 39.55 74.0 54.0 25.11 14.45 4510.5 48.10 35.09 H -0.61 47.49 34.48 74.0 54.0 26.51 19.52 5412.6 47.99 34.58 H 1.18 49.17 35.76 74.0 54.0 24.83 18.24 9021 49.75 37.48 H 5.73 55.48 43.21 74.0 54.0 18.52 10.79 * The magnitude of all emissions not reported were below the noise floor of the measurement system. Table 7.6.3-2: Radiated Spurious Emissions – Mid Channel Level (dBuV) Antenna Correction Corrected Level Limit Margin Frequency Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 2745 48.58 39.13 H -5.15 43.43 33.98 74.0 54.0 30.57 20.02 3660 50.78 39.44 H -2.15 48.63 37.29 74.0 54.0 25.37 16.71 3660 49.91 35.78 V -2.12 47.79 33.66 74.0 54.0 26.21 20.34 4575 48.76 35.24 H -0.50 48.26 34.74 74.0 54.0 25.74 19.26 4575 48.16 34.89 V -0.57 47.59 34.32 74.0 54.0 26.41 19.68 7320 49.09 36.10 H 5.27 54.36 41.37 74.0 54.0 19.64 12.63 7320 49.40 37.41 V 5.33 54.73 42.74 74.0 54.0 19.27 11.26 8235 48.29 34.14 H 5.74 54.03 39.88 74.0 54.0 19.97 14.12 9150 49.87 37.54 H 5.82 55.69 43.36 74.0 54.0 18.31 10.64 *The magnitude of all emissions not reported were below the noise floor of the measurement system. Table 7.6.3-3: Radiated Spurious Emissions – High Channel Level (dBuV) Antenna Correction Corrected Level Limit Margin Frequency Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 2783.7 48.22 38.16 H -5.05 43.17 33.11 74.0 54.0 30.83 20.89 3711.6 50.88 38.12 H -1.93 48.95 36.19 74.0 54.0 25.05 17.81 3711.6 49.45 36.44 V -1.88 47.57 34.56 74.0 54.0 26.43 19.44 7423.2 52.24 42.61 H 5.33 57.57 47.94 74.0 54.0 16.43 6.06 7423.2 50.82 39.67 V 5.41 56.23 45.08 74.0 54.0 17.77 8.92 8351.1 49.30 38.60 H 5.83 55.13 44.43 74.0 54.0 18.87 9.57 * The magnitude of all emissions not reported were below the noise floor of the measurement system. ACS Report: 07-0269 Advanced Compliance Solutions Page 21

Model: L+G S4e 2G Utilinet Endpoint FCC ID: R7PEC1R2S4 IC: 5294A-EC1R2S4 7.6.3.3 Sample Calculation: RC = RU + CFT Where: CFT = Total Correction Factor (AF+CA+AG)-DC (Average Measurements Only) RU = Uncorrected Reading RC = Corrected Level AF = Antenna Factor CA = Cable Attenuation AG = Amplifier Gain DC = Duty Cycle Correction Factor Example Calculation PEAK: Corrected Level: 49.32 - 5.24 = 44.08dBuV Margin: 74dBuV – 44.08dBuV = 29.92dB AVERAGE: Corrected Level: 39.74 - 5.24 = 34.50dBuV Margin: 54dBuV – 34.50dBuV = 19.50dB 8.0 CONCLUSION In the opinion of ACS, Inc. the L+G S4e 2G Utilinet Endpoint, manufactured by Cellnet Technology, Inc. meets the requirements of FCC Part 15 subpart C and Industry Canada’s Radio Standards Specification RSS-210. END REPORT ACS Report: 07-0269 Advanced Compliance Solutions Page 22


Document Created: 2007-08-07 14:04:44
Document Modified: 2007-08-07 14:04:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC