Plastics Spec

FCC ID: R4HAWEPPRO

Parts List/Tune Up Info

Download: PDF
FCCID_1454057

Cycolac* Resin FR15U Americas: COMMERCIAL Flame retardant ABS with excellent indoor UV properties and excellent processing. UL94 V-0/5VA rated. Elevated UL RTI rating (90-85-90) for all colors except for blue and green colors (60-60-60). TYPICAL PROPERTIES ¹ TYPICAL VALUE UNIT STANDARD MECHANICAL Tensile Stress, yld, Type I, 0.2 in/min 5400 psi ASTM D 638 Tensile Stress, brk, Type I, 0.2 in/min 4300 psi ASTM D 638 Tensile Strain, yld, Type I, 0.2 in/min 2.4 % ASTM D 638 Tensile Strain, brk, Type I, 0.2 in/min 17 % ASTM D 638 Tensile Modulus, 0.2 in/min 299000 psi ASTM D 638 Flexural Stress, yld, 0.05 in/min, 2 in span 9700 psi ASTM D 790 Flexural Modulus, 0.05 in/min, 2 in span 339000 psi ASTM D 790 Tensile Stress, yield, 50 mm/min 41 MPa ISO 527 Tensile Strain, break, 50 mm/min 21.9 % ISO 527 Tensile Modulus, 1 mm/min 2210 MPa ISO 527 Flexural Stress, yield, 2 mm/min 63 MPa ISO 178 Flexural Modulus, 2 mm/min 2260 MPa ISO 178 IMPACT Izod Impact, notched, 73°F 4 ft-lb/in ASTM D 256 Instrumented Impact Total Energy, 73°F 251 in-lb ASTM D 3763 Izod Impact, notched 80*10*4 +23°C 12 kJ/m² ISO 180/1A THERMAL Vicat Softening Temp, Rate B/50 201 °F ASTM D 1525 HDT, 66 psi, 0.125", unannealed 187 °F ASTM D 648 HDT, 264 psi, 0.125", unannealed 167 °F ASTM D 648 CTE, flow, -40°F to 100°F 5.E-05 1/°F ASTM E 831 CTE, xflow, -40°F to 100°F 5.1E-05 1/°F ASTM E 831 Vicat Softening Temp, Rate B/50 92 °C ISO 306 Relative Temp Index, Elec 90 °C UL 746B Relative Temp Index, Mech w/impact 85 °C UL 746B Relative Temp Index, Mech w/o impact 90 °C UL 746B PHYSICAL Specific Gravity 1.19 - ASTM D 792 1)Typical values only. Variations within normal tolerances are possible for variose colours.All values are 2)Only typical data for material selection purpose.Not to be used forpart or tool design. measured at least after 48 hoursstorage at 230C/50% relative humidity. 3)This rating is not intended to reflect hazards presented by this or anyother material under actual fire conditions. All properties, expect the melt volume rate are measured on injectionmoulded samples. 4)Own measurement according to UL. All samples are prepared according to ISO 294. Source, GMD, Last Update:12/08/2005 PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE SABIC INNOVATIVE PLASTICS COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("SABIC IP"), ARE SOLD SUBJECT TO SABIC IP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SABIC IP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SABIC IP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SABIC IP' S STANDARD CONDITIONS OF SALE, SABIC IP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each user bears full responsibility for making its own determination as to the suitability of SABIC IP' s materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to assure that its finished parts incorporating SABIC IP materials or products will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral recommendation or advice, shall be deemed to alter, vary, supersede, or waive any provision of SABIC IP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by SABIC IP. No statement contained herein concerning a possible or suggested use of any material, product or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of SABIC Innovative Plastics Company or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product or design in the infringement of any patent or other intellectual property right * Cycolac is a trademark of the SABIC Innovative Plastics Company © 1997-2007 SABIC Innovative Plastics Company.All rights reserved

Cycolac* Resin FR15U Americas: COMMERCIAL TYPICAL PROPERTIES ¹ TYPICAL VALUE UNIT STANDARD PHYSICAL Mold Shrinkage, flow, 0.125" 0.5 - 0.7 % GE Method Melt Flow Rate, 230°C/3.8 kgf 3.3 g/10 min ASTM D 1238 Melt Viscosity, 200°C, 1000 sec-1 3200 poise ASTM D 3825 Density 0.04 lb/in³ ISO 1183 Melt Flow Rate, 220°C/5.0 kg 7 g/10 min ISO 1133 Melt Volume Rate, MVR at 220°C/10.0 kg 40 cm³/10 min ISO 1133 ELECTRICAL Arc Resistance, Tungsten {PLC} 7 PLC Code ASTM D 495 Hot Wire Ignition {PLC) 2 PLC Code UL 746A High Voltage Arc Track Rate {PLC} 4 PLC Code UL 746A High Ampere Arc Ign, surface {PLC} 4 PLC Code UL 746A Comparative Tracking Index (UL) {PLC} 1 PLC Code UL 746A Volume Resistivity >1.E+14 Ohm-cm IEC 60093 Dielectric Strength, in oil, 3.2 mm 20 kV/mm IEC 60243-1 FLAME CHARACTERISTICS UL Recognized, 94V-0 Flame Class Rating (3) 0.059 in UL 94 UL Recognized, 94-5VA Rating (3) 0.11 in UL 94 1)Typical values only. Variations within normal tolerances are possible for variose colours.All values are 2)Only typical data for material selection purpose.Not to be used forpart or tool design. measured at least after 48 hoursstorage at 230C/50% relative humidity. 3)This rating is not intended to reflect hazards presented by this or anyother material under actual fire conditions. All properties, expect the melt volume rate are measured on injectionmoulded samples. 4)Own measurement according to UL. All samples are prepared according to ISO 294. Source, GMD, Last Update:12/08/2005 PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE SABIC INNOVATIVE PLASTICS COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("SABIC IP"), ARE SOLD SUBJECT TO SABIC IP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SABIC IP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SABIC IP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SABIC IP' S STANDARD CONDITIONS OF SALE, SABIC IP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each user bears full responsibility for making its own determination as to the suitability of SABIC IP' s materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to assure that its finished parts incorporating SABIC IP materials or products will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral recommendation or advice, shall be deemed to alter, vary, supersede, or waive any provision of SABIC IP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by SABIC IP. No statement contained herein concerning a possible or suggested use of any material, product or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of SABIC Innovative Plastics Company or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product or design in the infringement of any patent or other intellectual property right * Cycolac is a trademark of the SABIC Innovative Plastics Company © 1997-2007 SABIC Innovative Plastics Company.All rights reserved

Cycolac* Resin FR15U Americas: COMMERCIAL PROCESSING PARAMETERS TYPICAL VALUE UNIT Injection Molding Drying Temperature 180 - 190 °F Drying Time 2-4 hrs Drying Time (Cumulative) 8 hrs Maximum Moisture Content 0.01 % Melt Temperature 400 - 450 °F Nozzle Temperature 400 - 450 °F Front - Zone 3 Temperature 400 - 430 °F Middle - Zone 2 Temperature 390 - 410 °F Rear - Zone 1 Temperature 340 - 360 °F Mold Temperature 120 - 160 °F Back Pressure 50 - 100 psi Screw Speed 30 - 60 rpm Shot to Cylinder Size 50 - 70 % Vent Depth 0.0015 - 0.002 in 1)Typical values only. Variations within normal tolerances are possible for variose colours.All values are 2)Only typical data for material selection purpose.Not to be used forpart or tool design. measured at least after 48 hoursstorage at 230C/50% relative humidity. 3)This rating is not intended to reflect hazards presented by this or anyother material under actual fire conditions. All properties, expect the melt volume rate are measured on injectionmoulded samples. 4)Own measurement according to UL. All samples are prepared according to ISO 294. Source, GMD, Last Update:12/08/2005 PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE SABIC INNOVATIVE PLASTICS COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("SABIC IP"), ARE SOLD SUBJECT TO SABIC IP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SABIC IP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SABIC IP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SABIC IP' S STANDARD CONDITIONS OF SALE, SABIC IP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each user bears full responsibility for making its own determination as to the suitability of SABIC IP' s materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to assure that its finished parts incorporating SABIC IP materials or products will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral recommendation or advice, shall be deemed to alter, vary, supersede, or waive any provision of SABIC IP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by SABIC IP. No statement contained herein concerning a possible or suggested use of any material, product or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of SABIC Innovative Plastics Company or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product or design in the infringement of any patent or other intellectual property right * Cycolac is a trademark of the SABIC Innovative Plastics Company © 1997-2007 SABIC Innovative Plastics Company.All rights reserved


Document Created: 2007-12-17 14:39:12
Document Modified: 2007-12-17 14:39:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC