SAR report part 3

FCC ID: R38YL3636A

RF Exposure Info

Download: PDF
FCCID_3294414

Schmid & Partner Engineering AG s p e a a Zeughausstrasse 43, 8004 Zurich, Switzerland Phone +41 44 245 9700, Fax +41 44 245 9779 info@speag.com, http://www speag.com IMPORTANT NOTICE USAGE OF THE DAE 4 The DAE unit is a delicate, high precision instrument and requires careful treatment by the user. There are no serviceable parts inside the DAE. Special attention shall be given to the following points: Battery Exchange: The battery cover of the DAE4 unit is closed using a screw, over tightening the screw may cause the threads inside the DAE to wear out. Shipping of the DAE: Before shipping the DAE to SPEAG for calibration, remove the batteries and pack the DAE in an antistatic bag. This antistatic bag shall then be packed into a larger box or container which protects the DAE from impacts during transportation. The package shall be marked to indicate that a fragile instrument is inside. E—Stop Failures: Touch detection may be malfunctioning due to broken magnets in the E—stop. Rough handling of the E—stop may lead to damage of these magnets. Touch and collision errors are often caused by dust and dirt accumulated in the Estop. To prevent E—stop failure, the customer shall always mount the probe to the DAE carefully and keep the DAE unit in a non—dusty environment if not used for measurements. Repair: Minor repairs are performed at no extra cost during the annual calibration. However, SPEAG reserves the right to charge for any repair especially if rough unprofessional handling caused the defect. DASY Configuration Files: Since the exact values of the DAE input resistances, as measured during the calibration procedure of a DAE unit, are not used by the DASY software, a nominal value of 200 MOhm is given in the corresponding configuration file. Important Note: Warranty and calibration is void if the DAE unit is disassembled partly or fully by the Customer. Important Note: Never attempt to grease or oil the E—stop assembly. Cleaning and readjusting of the E— stop assembly is allowed by certified SPEAG personnel only and is part of the annual calibration procedure. Important Note: To prevent damage of the DAE probe connector pins, use great care when installing the probe to the DAE. Carefully connect the probe with the connector notch oriented in the mating position. Avoid any rotational movement of the probe body versus the DAE while turning the locking nut of the connector. The same care shall be used when disconnecting the probe from the DAE. Schmid & Partner Engineering TN_BRO40315AD DAE4.doc 11.12.2009

Callblfatlon Laboratory of \\\‘\QJ//’A} Schweizerischer Kalibrierdienst Schmid & Partner ifi(&é Service suisse d‘étalonnage Engineering AG . . T _/ g Servizio svizzero di taratura 4 n‘ 7 i ; i Zeughausstrasse 43, 8004 Zurich, Switzerland e/I//\\\\\\“ Swiss Calibration Service Aidats® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client Auden Certificate No: DAE4—905_Jun16 |CALIBRATION CERTIFICATE | Object DAE4 — SD 000 D04 BK — SN: 905 Calibration procedure(s) QA CAL—06.v29 Calibration procedure for the data acquisition electronics (DAE) Calibration date: June 22, 2016 This calibration certificate documents the traceability to national standards, which realize the physicalunits of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Keithley Multimeter Type 2001 SN: 0810278 09—Sep—15 (No:17153) Sep—16 Secondary Standards ID # Check Date (in house) Scheduled Check Auto DAE Calibration Unit SE UWS 053 AA 1001 O5—Jan—16 (in house check) In house check: Jan—17 Calibrator Box V2.1 SE UMS 006 AA 1002 05—Jan—16 (in house check) In house check: Jan—17 Name Function Signature Calibrated by: Dominique Steffen Technician @ Approved by: Fin Bomholt Deputy Technical Manager . \/ é QMbu/ ’d 124 > Issued: June 22, 2016 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DAE4—905_Jun16 Page 1 of 5

Calibration Laboratory of Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters e DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. e Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. e The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. e DC Voltage Measurement Linearity: Verification of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. e Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. e Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. e AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage e Input Offset Measurement. Output voltage and statistical results over a large number of zero voltage measurements. e Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. e Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. e Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. + Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—905_Jun16 Page 2 of 5

DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1LSB = 6.AuV , full range = —100...+300 mV Low Range: 1LSB= 61nV , full range = ~1....... +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y Z High Range 404.683 + 0.02% (k=2) 405.232 £0.02% (k=2) 404.815 £ 0.02% (k=2) Low Range 3.98074 + 1.50% (k=2) 4.00183 + 1.50% (k=2) 3.99763 + 1.50% (k=2) Connector Angle Connector Angle to be used in DASY system 260.0"41° Certificate No: DAE4—905_Jun16 Page 3 of 5

Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltage Linearity High Range Reading (uV) Difference (uV) Error (%) Channel X + Input 199992.43 ~1.76 —0.00 Channel X + Input 20001.63 1.32 0.01 Channel X — Input —19999.90 2.02 —0.01 Channel Y + Input 199987.76 —6.61 —0.00 Channel Y + Input 19995.86 —4.49 —0.02 Channel Y — Input —20000.23 1.57 —0.01 Channel Z + Input 199992.39 2.00 —0.00 Channel Z + Input 19995.03 5.12 —0.03 Channel 2 — Input —20000.48 1.42 —0.01 Low Range Reading (1V) Difference (uV) Error (%) Channel X + Input 2000.08 0.04 0.00 Channel X + Input 200.55 0.07 0.03 Channel X — Input —199.28 —0.03 0.02 Channel Y + Input 2000.27 0.08 0.00 Channel Y + Input 200.65 —0.12 —0.06 Channel Y — Input —199.27 —0.17 0.08 Channel Z + Input 2000.30 0.24 0.01 Channel Z + Input 199.95 —0.61 —0.31 Channel Z — Input —~199.92 —0.62 0.31 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (uV) Average Reading (1V) Channel X 200 8.82 7.40 — 200 ~7.07 —8.74 Channel Y 200 8.09 7.82 — 200 —8.60 —8.90 Channel Z 200 1.50 1.30 — 200 —2.84 —2.92 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input Voltage (mV) Channel X (uV) Channel Y (1V) Channel Z (uV) Channel X 200 — 5.88 ~1.06 Channel Y 200 9.49 — 6.99 Channel Z 200 9.56 7.65 — Certificate No: DAE4—905_Jun16 Page 4 of 5

4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 15898 16839 Channel Y 16137 14613 Channel Z 16368 15992 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10M Average (uV) min. Offset (uV) max. Offset (uv) * [(’:“,’;a'm" Channel X —~4.09 —~4.85 —2.84 0.31 Channel Y —0.23 —1.76 0.56 0.38 Channel Z —0.45 ~1.77 1.62 0.54 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channel X 200 200 Channel Y 200 200 Channel Z 200 200 8. Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vec) +7.9 Supply (— Vec) —7.6 9. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ Vec) +0.01 +6 +14 Supply (— Vee) —0.01 —8 —9 Certificate No: DAE4—905_Jun16 Page 5 of 5

Calibration Laboratory of «l «um Schweizorischer Kalibrierdienst s w o o m as Schmid & Partner Service sulsse d‘étalonnage E Engineering AG zn Servizlo svizzero di taratura w Py Zoughausstrasse 43, 8004 Zurich, Switzerland Nt Yihtals® Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agroementfor the recognition of callbration certificates Client Sporton—SZ (Auden) Certificate No: EX3—3911_Sep16 CALIBRATION CERTIFICATE Object EX3DV4 — SN:3911 Callbration procedure(s) QA CAL—01.v9, QA CAL—14.v4, QA CAL—23.v5, QA CAL—25.v6 Calibration procedure for dosimetric E—field probes Callbration date: September 29, 2016 This calibration certficate documents the traceablity to national standards, which realize the physical units of measurements (S1): The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certiicate. All calibrations have been conducted in the closed laboratory facilty: environment temperature (22 + 3)°C and humidiy <70%. Callbration Equipment used (M&TE criical for callbration) Primary Standards iD Gal Date (Gortificate No.) Scheduled Calibration Power meter NRP SN: 104778 06—Apr—16 (No. 217—02288/02209) Aprt7 Power sensor NRP—291 SN: 103244 06—Apr—16 (No. 217—02288) Apr—iT Power sensor NRP—291 SN 103245 06—Apr—16 (No. 217—02289) Aprt? Reference 20 dB Attenuator SN: s527? (20) 05—Apr—16 (No. 217—02203) Apr7 Reference Probe ESSDV2 SN: 3013 31—Dec—15 (No. ES3—3013_Dect5) Dec—16 DAE4 SN: 660 23—Dec—15 (No. DAE4—660_Dec15) Dec—16 Secondary Standards iD Check Date (in house) Scheduled Check Power meter E44198 SN: GB41203874 06—Apr—16 (in house chack Jun—16) in house check Jun—18 Power sensor E4412A SN: MY41498087 06—Apr—16 (in house check Jun—16) in house check: Jun—18 Power sensor E4412A SN: 000110210 06—Apr—16 (in house check Jun—16) in house check Jun—18 RF generator HP 8648G ShN: US3642U01700 04—Aug—99 (in house check Jun—16) in house check Jun—18 Network Analyzer HP 8753E SN: Us37300585 18—0ct—01 (in house check Oct—15) in house check: Oct—16 =7tp Name Function Signature Callbrated by: Leif Klysner Laboratory Technician Approved by: Katia Pokovic Technical Manager xt Issued: October 4, 2016 This callbration certficate shall not be reproduced exceptin full without written approval of the laboratory. Certificate No: EX3—3911_Sep16 Page 1 of 11

Calibration Laboratory of «05 s\ g Schwolzerischer Kalibrierdionst f Schmid & Partner i‘h\t;//m _ Service suisse d‘étalonnage Engineering AG Ty «g Servirio sviezoro di taratura Zeughausstrasse 43, 8004 Zurich, Switzeriand *Afi-\"‘? Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of callbration certificates Glossary: TSL tissue simulating liquid NORMxy,z sensitivity in free space ConvF sensitivity in TSL / NORMx.y,z DCP diode compression point CF crest factor(1/duty_cycle) of the RF signal A, B,C, D modulation dependentlinearization parameters Polarization ip @p rotation around probe axis Polarization 8 8 rotation around an axis that is in the plane normal to probe axis (at measurement center), ie., 8 = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, June 2013 b) IEC 62209—1, "Procedure to measurethe Specific Absorption Rate (SAR) for hand—held devices usedin close proximity to the ear (frequency range of 300 MHz to 3 GHz), February 2005 0) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)®, March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: NORMx.y,z: Assessed for E—field polarization 8 = 0 (f < 900 MHz in TEM—cell; f> 1800 MHz: R22 waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not affect the E*—field uncertainty inside TSL (see below ConvF). NORM\(x,y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is implementedin DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. DCPxy,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics AsyaBuy,z Cuy.z: Dxy,z; VRiy,z: A, B, C, D are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across thediode. ConvF and Boundary Effect Parameters: Assessedin flat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx.y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to + 100 MHz. Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. SensorOffset: The sensoroffset corresponds to theoffset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: EX3—3911_Sep16 Page 2 of 11

EX3DV4 — SN:3911 September 29, 2016 Probe SN:3911 Manufactured: September 4, 2012 Calibrated: September 29, 2016 Calibrated for DASY/EASY Systems {Note: non—compatible with DASY2 system!) Certificate No: EX3—3911_Sep16 Page 3 of 11

EX3DV4— SN:3911 September 29, 2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3911 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (uV/(V/im)*)* 0.30 0.33 0.47 +10.1 % DCP (myv}* 101.9 102.3 100.2 Modulation Calibration Parameters UID Communication System Name A B C D VR Unc® dB dBvuV dB mV (k=2) 0 CW xX 0.0 0.0 1.0 0.00 138.8 £3.5 % Y 0.0 0.0 1.0 138.9 Z 0.0 0.0 1.0 138.4 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X,Y,Z do not affect the E*—field uncertainty inside TSL (see Pages 5 and 6). ® Numerical linearization parameter: uncertainty not required. & Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: EX3—3911_Sep16 Page 4 of 11

EX3DV4— SN:3911 September 29, 2016 DASY/EASY — Parameters of Probe: EX3DV4 SN:3911 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity Depth ° Unc f(MHz)° Permittivity® (S/im)" ConvFX ConvFY ConvFZ Aipha® (mm) (k=2) 750 41.9 0.89 10.99 10.99 10.99 0.57 0.81 *# 12.0 % 835 41.5 0.90 10.54 10.54 10.54 0.26 1.26 # 12.0 % 900 41.5 0.97 10.05 10.05 10.05 0.38 0.93 £#12.0 % 1750 40.1 1.37 8.88 8.88 8.88 0.31 0.93 + 12.0 % 1900 40.0 1.40 8.50 8.50 8.50 0.40 0.80 #12.0 % 2000 40.0 1.40 8.48 8.48 8.48 0.35 0.85 #* 12.0 % 2300 39.5 1.67 7.93 7.93 7.93 0.36 0.80 + 12.0 % 2450 39.2 1.80 7.43 7.A3 7.43 0.29 0.98 + 12.0 % 2600 39.0 1.96 7.39 7.39 7.39 0.45 0.80 + 12.0 % 5250 35.9 4.71 5.25 5.25 5.25 0.40 1.80 £# 13.1 % 5600 35.5 5.07 4.49 4.49 4.49 0.50 1.80 + 13.1 % 5750 35.4 5.22 4.75 4.75 4.75 0.50 1.80 *# 13.1 % © Frequency validity above 300 MHz of £ 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is * 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to £ 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (s and 0) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (s and 0) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—3911_Sep16 Page 5 of 11

EX3DV4— SN:3911 September 29, 2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3911 Calibration Parameter Determined in Body Tissue Simulating Media Relative Conductivity Depth ° Unc f(MHz)° Permittivity"® (Sim}" ConvF X ConvF Y¥ ConvFZ Alpha® (mm) (k=2) 750 55.5 0.96 10.43 10.43 10.43 0.42 0.80 + 12.0 % 835 55.2 0.97 10.19 10.19 10.19 0.20 1.33 + 12.0 % 1750 53.4 1.49 8.46 8.46 8.46 0.42 0.80 £# 12.0 % 1900 53.3 1.52 8.17 8.17 8.17 0.35 0.97 + 12.0 % 2300 52.9 1.81 7.93 7.93 7.93 0.33 0.98 #12.0 % 2450 52.7 1.95 7.66 7.66 7.66 0.43 0.80 + 12.0 % 2600 52.5 216 7.38 7.38 7.38 0.33 0.80 +12.0 % 5250 48.9 5.36 4.62 4.62 4.62 0.50 1.90 *13.1 % 5600 48.5 5.77 3.78 3.78 3.78 0.60 1.90 £#13.1 % 5750 48.3 5.94 3.95 3.95 3.95 0.60 1.90 £13.1 % © Frequency validity above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to £ 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (e and 0) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (s and 0) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. 8 Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—3911_Sep16 Page 6 of 11

EX3DV4— SN:3911 September 29, 2016 Frequency Response of E—Field (TEM—Cell:if110 EXX, Waveguide: R22) Termmert Frequency response (normalized) Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: EX3—3911_Sep16 Page 7 of 11

EX3DV4— SN:3911 September 29, 2016 Receiving Pattern (¢), 8 = 0° £=600 MHz,TEM f=1800 MHz,R22 im o as . vew# is mss * (ars ® ® o* # To: x ¥ 2 |0‘FTMLZ Gfi%z 1865.de 2555!#)'11 Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificale No: EX3—3911_Sep16 Page 8 of 11

EX3DV4— SN:3911 September 29, 2016 Dynamic Range f(SARneaq) (TEM cell , fova= 1900 MHz) 105 3 ® 8 & UJ 2 10 & 10° 10‘ 1 U T T I 10 102 101 10 10‘ 10 10° 8 SAR (mWiom3] L4] not compensated compensated a & 5E d 19° 10 1J0? 103 SAR {mW/om3] not compansated compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—3911_Sep16 Page 9 of 11

EXGDV4— SN:3911 September 29, 2016 Conversion Factor Assessment 1= 835 MHz.WGLS R9 (H_conv) f= 1900 MHz,WGLS R22 (H_convr) «0 ‘ as| ‘ ® so: \ x % §"t " gm| ? > §.} 16 5 : * ml 18 asl mss S pitoacimetrce on oi n sastoraca uce q cficfecitnpic ic ie is .; & iob & m &0 ainn) & 0# m m $ 4C aC CA C «finnt % in 81 _A al a) ardhiea messued anahiea meavees Deviation from Isotropy in Liquid Error (¢, 9), £= 900 MHz eviation: —10 —08 —06 .04 —02 00 02 04 06 08 10 Uncertainty of Spherical Isotropy Assessment: # 2.6% (k=2) Certificate No: EX3—3911_Sep16 Page 10 of 11

EX3DV4— SN:3911 September 29, 2016 DASY/EASY — Parameters of Probe: EX3DV4 — SN:3911 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 80 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 1.4 mm Certificate No: EX3—3911_Sep16 Page 11 of 11


Document Created: 2017-12-23 07:27:54
Document Modified: 2017-12-23 07:27:54
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC