I15Z41179-SEM03_SAR_Rev0(0720)-2 part 4

FCC ID: R38YL3320A

Test Report

Download: PDF
FCCID_2710294

mm© /7/ e .l ® in Collaboration with T7T77L a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp:/www.chinattl.en DASY5 Validation Report for Body TSL Date: 05.11.2014 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN: 54088 Communication System: UID 0, CW; Frequency: 1900 MHz;Duty Cycle: 1:1 Medium parameters used: £= 1900 MHz; 0 = 1.511 $/m; s, = 54.12; p = 1000 kg/m3 Phantom section: Left Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN3617; ConvF(7.58, 7.58, 7.58); Calibrated: 2014—08—28; * Sensor—Surface: 2mm (Mechanical Surface Detection) * Electronics: DAE4 Sn1331; Calibrated: 2014—01—23 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 * Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) System Performance Check at Frequencies above 1 GHz/d=10mm, Pin=250 mW, dist=2.0mm (EX—Probe)/Zoom Scan (7x7x7) (8x7x7)/Cube 0: Measurement grid: dx=Smm, dy=5mm, dz=5mm Reference Value = 95.67 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 18.4 W/kg SAR(I g) = 10.2 W/kg; SAR(10 g) = 5.35 W/kg Maximum value of SAR (measured) = 14.6 W/kg dB 0 —6.72 "13.44 20.16 S is —26.00 _——-a—__—_ —33.60 0 dB = 15.7 W/kg = 11.96 dBW/kg Certificate No: Z14—97130 Page 7 of 8

TTL s_9_e_a_a ® in Collaboration with Add: No.31 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt@chinattl.com Hitp:/www.chinattl.en Impedance Measurement Plot for Body TSL [FIIIRI si7 Log May 10.00de7 ref 0.000ds [ri vell 5—°0 132 ~3.5000000 onz =24.056 dB 30.00 —40. 00 ~50. 00 x Tra s11 smith (M+JX) scale 1.000U [F1 be1] s 1.9000000 onz as.528 o. 6.or07 o s03.49—5m~ ~ Certificate No: Z14—97130 Page 8 of 8

wl in Collaboration with |§?}j{ {t| a 8 \a" TTL a_ i causranonN LABORATORY zn wl Cl Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China * * \\S CALIBRATION Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 thulaks No. L570 E—mail: ctl@chinattl. com Hitp://www.chinattl.cn Client CTTL(South Branch) Certificate No: 214—97131 Object D2450V2 — SN: 873 Calibration Procedure(s) TMC—OS—E—02—194 Calibration Procedures for dipole validation kits Calibration date: November 3, 2014 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(223)C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 101919 01—Jul—14 (CTTL, No.J14X02146) Jun—15 Power sensor NRP—Z91 101547 01—Jul—14 (CTTL, No.J14X02146) Jun—15 Reference Probe EX3DV4 SN 3617 28—Aug—14(SPEAG,No.EX3—3617_Aug14) Aug—15 DAE4 SN 1331 23—Jan—14 (SPEAG, DAE4—1331_Jan14) Jan—15 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration SignalGeneratorMG3700A 6201052605 O1—Jul—14 (CTTL, No.J14X02145) Jun—15 Network Analyzer E5071C MY46110673 15—Feb—14 (TMC, No.JZ14—781) Feb—15 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer ¢é’) Reviewed by: Qi Dianyuan SAR Project Leader Eh. . Approved by: Lu Bingsong Deputy Director of the laboratory Issued: November 5, 2014 fork This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z14—97131 Page 1 of 8

G ~ a7TTL a_a 1 e \llggzyy E—mail: cttl@chinattl.com CALSRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing. 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 Hitp:/www.chinatt.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) For hand—held devices used in close proximity to the ear (frequency range of 300MHz to 3GHz)", February 2005 c) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: & Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Returm Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. & Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. & SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. & SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z14—97131 Page 2 of 8

|~ G TTL 5.834 ® In Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 E—mail: cttl@chinattl.com Fax: +86—10—62304633—2504 Hitpy//www.chinattl.en Measurement Conditions DASY system configuration, as far as not given on page 1 DASY Version DASY52 52.8.8.1222 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center— TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 2450 MHz & 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 £0.2) °C 40.1 46 % 1.84 mho/m + 6 % Head TSL temperature change during test <1.0 °C —— ——— SAR result with Head TSL SAR averaged over 1_Cm*_(1 g) of Head TSL Condition SAR measured 250 mW input power 13.5 mW /g SAR for nominal Head TSL parameters normalized to 1W 53.7 mW ig £ 20.8 % (k=2) SAR averaged over 10 cm° (10 g) of Head TSL Condition SAR measured 250 mW input power 6.34 mW /g SAR for nominal Head TSL parameters normalized to 1W 25.3 mW /g £ 20.4 % (k=2) Body TSL parameters Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 £0.2) °C 51.4 26 % 1.99 mho/m +6 % Body TSL temperature change during test <1.0 °C —— — SAR result with Head TSL SAR averaged over 1_cm*_(1 g) of Body TSL Condition SAR measured 250 mW input power 13.2 mW /g SAR for nominal Body TSL parameters normalized to 1W §2.0 mW ig £ 20.8 % (k=2) SAR averaged over 10 cm° (10 g) of Body TSL Condition SAR measured 250 mW input power 6.19 mW /g SAR for nominal Body TSL parameters normalized to 1W 24.5 mW ig £ 20.4 % (k=2) Certificate No: Z14—97131 Page 3 of 8

* in Collaboration with iTTL a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp://www.chinattl.cn Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 50.70+ 5.02j0 Retun Loss —26.00B Antenna Parameters with Body TSL Impedance, transformed to feed point 48.70+ 5.680 Return Loss —24.60B General Antenna Parameters and Design Electrical Delay (one direction) 1.043 ns | After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding lineis directly connected to the second arm of the dipole. The antennais therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in orderto improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend orthe soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z14—97131 Page 4 of 8

a7T1T a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt!@chinattl.com Hitp://www.chinatl.en DASYS5 Validation Report for Head TSL Date: 03.11.2014 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 873 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1: 1 Medium parameters used: {= 2450 MHz; a = 1.842 S/m; &, = 40.1; p = 1000 kg/m3 Phantom section: Right Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN3617; ConvF(7.19, 7.19, 7.19); Calibrated: 2014—08—28; * Sensor—Surface: 2mm (Mechanical Surface Detection) « Electronics: DAE4 Sn1331; Calibrated: 2014—01—23 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 * Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) System Performance Check at Frequencies above 1 GHz/d=10mm, Pin=250 mW, dist=2.0mm (EX—Probe)/Zoom Scan (7x7x7) (8x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 103.3 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 27.3 W/kg SAR(I g) = 13.5 W/kg; SAR(10 g) = 6.34 W/kg Maximum value of SAR (measured) = 20.3 W/kg dB 0 ~4.47 —8.94 "13.42 —17.89 ~22.36 0 dB = 20.3 W/kg = 13.07 dBW/kg Certificate No: Z14—97131 Page 5 of 8

© t3 — ® in Collaboration with ‘TTL a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ett@chinattl.com Hitp:/www.chinattl.on Impedance Measurement Plot for Head TSL Tri s11 Log Mag 10.00de/ ref 0.000db [Fi vel] hi si1 saith (r4J») scale 1.000u [F1 be1] * 32 2.4500000 cz 50.727 0 5.0100 n 326.Qg—pf mm Certificate No: Z14—97131 Page 6 of 8

TTL 12838 ® in Collaboration with Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hutpy/www.chinattl.en DASYS5 Validation Report for Body TSL Date: 02.11.2014 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 873 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: £= 2450 MHz; 0 = 1.991 S/m;& = 51.37; p = 1000 kg/m* Phantom section: Center Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASYS Configuration: «_ Probe: EX3DV4 — SN3617; ConvF(7.31, 7.31, 7.31); Calibrated: 2014—08—28; « Sensor—Surface: 2mm (Mechanical Surface Detection) * Electronics: DAE4 Sn1331; Calibrated: 2014—01—23 «_ Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA: Serial: 1161/1 * Measurement SW: DASYS2, Version 52.8 (8); SEMCAD X Version 14.6.10 (7331) System Performance Check at Frequencies above 1 GHz/d=10mm, Pin=250 mW, dist=2.0mm (EX—Probe)/Zoom Scan (7x7x7) (8x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=Smm Reference Value = 100.6 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 27.1 W/kg SAR(I g) =13.2 W/kg; SAR(10 g) =6.19 W/kg Maximum value of SAR (measured) = 20.3 W/kg dB 0 ~4.56 812 —13.68 18.24 —22.80 0 dB = 20.3 W/kg = 13.07 dBW/kg Certificate No: Z14—97131 Page 7 of 8

) 4.TL | 7TTL a 1 e Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp://www.chinattl.en Impedance Measurement Plot for Body TSL A~ Certificate No: Z14—97131 Page 8 of 8

No.I15Z41179-SEM03 Page 134 of 134 ANNEX I Accreditation Certificate ***END OF REPORT*** ©Copyright. All rights reserved by CTTL.


Document Created: 2019-05-31 23:27:28
Document Modified: 2019-05-31 23:27:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC