Users Manual

FCC ID: QZC-ELIR1

Users Manual

Download: PDF
FCCID_2958583

DRAFT Litenode™ wireless node Single load RME-GEN Installation instructions IL42-5047A Description Part of the DimOnOff wireless control technology, Litenode relays are suitable for general purpose lighting control applications that add intelligent functions and networkability to any light fixture. The relay provides continuous retroactive 0 V to 10 V (sink/source) for all types of ballasts and drivers and provide power to external sensors (optional). • intelligent distributed control, metering, and monitoring • NEMA C136-41 • 5- and 7-pin with continuous retroactive 0 V to 10 V dimming Operation Unless otherwise programmed, the relay will turn on the fixture approximately 10 seconds after power is restored to the relay. The yellow LED will blink when power is properly applied. Using DimOnOff software, test the communications link with the relay. Before you install • This device is to be installed and/or used in accordance with appropriate electrical codes and regulations. • If you are unsure about any part of these instructions, consult a qualified electrician. • Use this device only with NEMA C136-41 or C136-10 certified receptacles. Use authorized utility procedures to install or service this device. Dangerous voltages are present. Disconnect power at the circuit breaker or fuse when servicing, installing, or removing the light fixture. Equipment damage, personal injury, or death may result if safety precautions are not followed.

DRAFT Litenode™ wireless node 2 Installation Use authorized utility procedures to install or service this device. Dangerous voltages are present. Disconnect power at the circuit breaker or fuse when servicing, installing, or removing the light fixture. Equipment damage, personal injury, or death may result if safety precautions are not followed. If you are uncertain about any part of these instructions, consult a qualified electrician. The node input and output are low voltage (24 VDC). Consult local building codes and regulations for information regarding low-voltage installation. 1 To avoid fire, shock, or death, be sure to turn off power at the circuit breaker or fuse. Verify that power is off before proceeding. 2 Connect lead wires according to the wiring diagram as follows: - Line voltage wiring: Remove 5/8-inch (1.6 cm) of insulation from each circuit conductor. Make sure that the ends of the conductors are straight. Connect lead wires from relay to line per the appropriate wiring diagram as follows. Twist strands of each lead tightly and, with circuit conductors, push firmly into the appropriate wire connector. Screw connectors on clockwise making sure that no bare conductor shows below the wiring connectors. Secure each connector with electrical tape. - Class II warning: Connect low-voltage wires from relay to fixture per appropriate wiring diagram as follows. Twist strands of each lead tightly, and with circuit conductors, push firmly into appropriate wire connector. Screw connectors on clockwise, making sure that no bare conductor shows below the wire connectors. Make sure to cap-off unused low-voltage wires. Secure each connector with electrical tape. 3 Restore power at circuit breaker or fuse. RME-GEN wiring Line wires on C-136 socket supplied by others Color Gauge Line in Black 14 Neutral/line 2 White 14 Line out Red 14 DC control wires on C-136 socket supplied by others 0 V to 10 V+ out Purple 18 0 V to 10 V- ground out Gray 18 Digital in 13 VDC to 30 VDC Orange 18 VCC 24 VDC 50 mA Brown 18

DRAFT Litenode™ wireless node 3 Antenna location and installation The antenna for the model ELIR1 Lightnode relay is integral to the unit and is contained wholly within the device itself. It is not accessible to the user and may not be modified in any way. To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer distance than 20 cm is not recommended. Troubleshooting General • Make sure the wires are connected according to the wiring diagram. • Make sure the wires have proper contact and are securely connected. • If no LEDs are lit, then check the power. Lights won’t turn on when relay is being powered: • Make sure the wires are properly connected. • Make sure the yellow LED is blinking. Light won’t turn off after command has been sent: • Make sure that relay is receiving communication (red LED blinks) Relay doesn’t respond to commands: • Make sure no obstacle (concrete, metal, etc.) is present between relay antenna and the emitter. LED indicators: • Yellow: blinks every 3 seconds to indicate that relay is powered and functioning normally • Red: flashes to indicate message reception • Green: flashes to indicate message transmission by the relay. If there is no message reception/transmission, then possible causes are antenna positioning and distance from another relay or the gateway. Specifications • Model: ELIR1 • IC: 4557A-ELIR1 • FCC ID: QZC-ELIR1 • Operating range: 110 VAC to 480 VAC 50 Hz or 60 Hz • Max output: 8 A (2 A at 480 V) • Inputs: 1 digital (0 VDC to 30 VDC), optional • Output: 24 VDC 50 mA max • Continuous retroactive 0 V to 10 V dimming See the product data sheet for complete details

DRAFT Litenode™ wireless node 4 WARNING (PART 15.21) Changes or modifications not expressly approved by Elster could void the user's authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. COMPLIANCE STATEMENT (FCC PART 15.19 AND INDUSTRY CANADA) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. ÉNONCÉ DE CONFORMITÉ Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. LiteNode is a trademark and/or registered trademark of DimOnOff Installation information obtained from DimOnOff and is used by permission of DimOnOff. DISCLAIMER OF WARRANTIES AND LIMITATIONS OF LIABILITY There are no understandings, agreements, representations, or warranties either express or implied, including warranties of merchantability or fitness for a particular purpose, other than those specifically set out by any existing contract between the parties. Any such contract states the entire obligation of the seller. The contents of this document shall not become part of or modify any prior existing agreement, commitment, or relationship. The information, recommendations, descriptions, and safety notices in this document are based on Elster Solutions, LLC experience and judgment with respect to operation and maintenance of the described product. This information should not be considered as all-inclusive or covering all contingencies. If further information is required, Elster Solutions, LLC should be consulted. No warranties, either expressed or implied, including warranties of fitness for a particular purpose or merchantability, or warranties arising from the course of dealing or usage of trade, are made regarding the information, recommendations, descriptions, warnings, and cautions contained herein. In no event will Elster Solutions, LLC be responsible to the user in contract, in tort (including negligence), strict liability or otherwise for any special, indirect, incidental, or consequential damage or loss whatsoever, including but not limited to: damage or loss of use of equipment, cost of capital, loss of profits or revenues, or claims against the user by its customers resulting from the use of the information, recommendations, descriptions, and Elster Solutions safety notices contained herein. Raleigh, North Carolina Technical support: 800 338 5251 © 2016 by Elster. All rights reserved. Produced in the United States.


Document Created: 2019-11-11 10:35:48
Document Modified: 2019-11-11 10:35:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC