Test Report

FCC ID: QYLPS336R

Test Report

Download: PDF
FCCID_1845402

FCC TEST REPORT (RFID) REPORT NO.: RF120629C20-4 MODEL NO.: TRF7960RHBR FCC ID: QYLPS336R RECEIVED: Jun. 29, 2012 TESTED: Oct. 04 ~ Oct. 07, 2012 ISSUED: Oct. 16, 2012 APPLICANT: Getac Technology Corporation. ADDRESS: 5F., Building A, No. 209, Sec. 1, Nangang Rd., Nangang Dist, Taipei City 11568, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF120629C20-4 1 of 29 Report Format Version 5.0.0

Table of Contents RELEASE CONTROL RECORD ........................................................................................................ 3 1. CERTIFICATION ..................................................................................................................... 4 2. SUMMARY OF TEST RESULTS ............................................................................................ 5 2.1 MEASUREMENT UNCERTAINTY ........................................................................................ 5 3. GENERAL INFORMATION ..................................................................................................... 6 3.1 GENERAL DESCRIPTION OF EUT...................................................................................... 6 3.2 DESCRIPTION OF TEST MODES........................................................................................ 6 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ....................................... 7 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS....................................................... 8 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................................. 9 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST................................................................... 9 4. TEST TYPES AND RESULTS .............................................................................................. 10 4.1 RADIATED EMISSION MEASUREMENT ........................................................................... 10 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT ........................................................ 10 4.1.2 TEST INSTRUMENTS ......................................................................................................... 11 4.1.3 TEST PROCEDURES ......................................................................................................... 12 4.1.4 DEVIATION FROM TEST STANDARD ............................................................................... 12 4.1.5 TEST SETUP ...................................................................................................................... 13 4.1.6 EUT OPERATING CONDITIONS ........................................................................................ 13 4.1.7 TEST RESULTS .................................................................................................................. 14 4.2 CONDUCTED EMISSION MEASUREMENT ...................................................................... 18 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ................................................... 18 4.2.2 TEST INSTRUMENTS ........................................................................................................ 18 4.2.3 TEST PROCEDURES ......................................................................................................... 19 4.2.4 DEVIATION FROM TEST STANDARD ............................................................................... 19 4.2.5 TEST SETUP ...................................................................................................................... 19 4.2.6 EUT OPERATING CONDITIONS ........................................................................................ 19 4.2.7 TEST RESULTS .................................................................................................................. 20 4.3 FREQUENCY STABILITY ................................................................................................... 22 4.3.1 LIMITS OF FREQUENCY STABILITY MEASUREMENT ................................................... 22 4.3.2 TEST INSTRUMENTS ........................................................................................................ 22 4.3.3 TEST PROCEDURE ........................................................................................................... 22 4.3.4 DEVIATION FROM TEST STANDARD ............................................................................... 23 4.3.5 TEST SETUP ...................................................................................................................... 23 4.3.6 EUT OPERATING CONDITION .......................................................................................... 23 4.3.7 TEST RESULTS .................................................................................................................. 24 4.4 20dB BANDWIDTH ............................................................................................................. 25 4.4.1 LIMITS OF 20dB BANDWIDTH MEASUREMENT ............................................................. 25 4.4.2 TEST INSTRUMENTS ........................................................................................................ 25 4.4.3 TEST PROCEDURE ........................................................................................................... 25 4.4.4 DEVIATION FROM TEST STANDARD ............................................................................... 25 4.4.5 TEST SETUP ...................................................................................................................... 25 4.4.6 EUT OPERATING CONDITION .......................................................................................... 25 4.4.7 TEST RESULTS .................................................................................................................. 26 5. PHOTOGRAPHS OF THE TEST CONFIGURATION........................................................... 27 6. INFORMATION ON THE TESTING LABORATORIES ......................................................... 28 7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ................................................................................................................. 29 Report No.: RF120629C20-4 2 of 29 Report Format Version 5.0.0

RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF120629C20-4 Original release Oct. 16, 2012 Report No.: RF120629C20-4 3 of 29 Report Format Version 5.0.0

1. CERTIFICATION PRODUCT: RFID Module MODEL NO.: TRF7960RHBR BRAND: TI APPLICANT: Getac Technology Corporation. TEST SAMPLE: ENGINEERING SAMPLE TESTED: Oct. 04 ~ Oct. 07, 2012 STANDARDS: FCC Part 15, Subpart C (Section 15.225) FCC Part 15, Subpart C (Section 15.215) ANSI C63.10-2009 The above equipment (model: TRF7960RHBR) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Oct. 16, 2012 Pettie Chen / Senior Specialist APPROVED BY : , DATE: Oct. 16, 2012 Ken Liu / Manager Report No.: RF120629C20-4 4 of 29 Report Format Version 5.0.0

2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC PART 15, SUBPART C (SECTION 15.225, 15.215) STANDARD TEST TYPE AND LIMIT RESULT REMARK SECTION Meet the requirement of limit. 15.207 Conducted emission test PASS Minimum passing margin is -1.80dB at 13.55859MHz. Meet the requirement of limit. The field strength of any emissions 15.225 (a) PASS Minimum passing margin is within the band 13.553-13.567 MHz -69.5dB at 13.56MHz. The field strength of any emissions Meet the requirement of limit. 15.225 (d) appearing outside of the 13.110-14.010 PASS Minimum passing margin is MHz band -18.5dB at 955.38MHz. 15.225 (e) The frequency tolerance PASS Meet the requirement of limit. 15.215 (c) 20dB Bandwidth PASS Meet the requirement of limit. 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: MEASUREMENT FREQUENCY UNCERTAINTY Conducted emissions 150kHz~30MHz 2.44 dB 30MHz ~ 200MHz 3.34 dB Radiated emissions 200MHz ~1000MHz 3.35 dB This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Report No.: RF120629C20-4 5 of 29 Report Format Version 5.0.0

3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT RFID Module MODEL NO. TRF7960RHBR POWER SUPPLY 3.7Vdc MODULATION TYPE ASK OPERATING FREQUENCY 13.56MHz ANTENNA TYPE Loop antenna I/O PORTS Refer to users’ manual DATA CABLE NA ACCESSORY DEVICES NA NOTE: 1. The EUT is authorized for use in specific End-product (PDA, model no.: PS336 and brand name: Getac). 2. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. 3.2 DESCRIPTION OF TEST MODES The EUT only have one channel. CHANNEL FREQUENCY (MHz) 1 13.56 Report No.: RF120629C20-4 6 of 29 Report Format Version 5.0.0

3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL EUT APPLICABLE TO CONFIGURE DESCRIPTION MODE RE PLC FS BW - √ √ √ √ - Where RE: Radiated Emission PLC: Power Line Conducted Emission FS: Frequency Stability BW: 20dB Bandwidth NOTE: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Y-plane. RADIATED EMISSION TEST: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 1 ASK POWER LINE CONDUCTED EMISSION TEST: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 1 ASK FREQUENCY STABILITY: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 1 ASK 20dB BANDWIDTH: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, antenna ports (if EUT with antenna diversity architecture). AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 1 ASK Report No.: RF120629C20-4 7 of 29 Report Format Version 5.0.0

TEST CONDITION: APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY RE 25deg. C, 65%RH 5Vdc Chris Lin PLC 23deg. C, 79%RH 5Vdc Nick Chen FT 24deg. C, 70%RH 5Vdc Nick Chen BW 20deg. C, 45%RH 5Vdc Chris Lin 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RFID Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.225) FCC Part 15, Subpart C (15.215) ANSI C63.10-2009 All test items have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B. The test report has been issued separately. Report No.: RF120629C20-4 8 of 29 Report Format Version 5.0.0

3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID 1 PDA Getac PS336 NA NA NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS 1 NA NOTE: 1. All power cords of the above support units are non shielded (1.8m). 2. Item 1 was provided by client. 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST PDA EUT (Powered from host equipment) Test table Report No.: RF120629C20-4 9 of 29 Report Format Version 5.0.0

4. TEST TYPES AND RESULTS 4.1 RADIATED EMISSION MEASUREMENT 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT The field strength of any emissions within the band 13.553-13.567 MHz shall not exceed 15,848 microvolts/meter at 30 meters. The field strength of any emissions appearing outside of the 13.110-14.010 MHz band shall not exceed the general radiated emission limits in §15.209. FIELD STRENGTH MEASUREMENT DISTANCE FREQUENCIES (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF120629C20-4 10 of 29 Report Format Version 5.0.0

4.1.2 TEST INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION Test Receiver ESIB7 100212 Aug. 06, 2012 Aug. 05, 2013 ROHDE & SCHWARZ Spectrum Analyzer FSP40 100039 Feb. 03, 2012 Feb. 02, 2013 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-160 Apr. 06, 2012 Apr. 05, 2013 SCHWARZBECK HORN Antenna 9120D 209 Sep. 03, 2012 Sep. 02, 2013 SCHWARZBECK HORN Antenna BBHA 9170 148 Jul. 11, 2012 Jul. 10, 2013 SCHWARZBECK Loop Antenna HFH2-Z2 100070 Jan. 31, 2012 Jan. 30, 2014 Preamplifier 8447D 2944A10633 Oct. 29, 2011 Oct. 28, 2012 Agilent Preamplifier 8449B 3008A01964 Oct. 29, 2011 Oct. 28, 2012 Agilent RF signal cable SUCOFLEX 104 250723/4 Aug. 28, 2012 Aug. 27, 2013 HUBER+SUHNNER RF signal cable SUCOFLEX 106 12738/6+309224/4 Aug. 28, 2012 Aug. 27, 2013 HUBER+SUHNNER Software ADT_Radiated_ NA NA NA ADT. V7.6.15.9.2 Antenna Tower MA 4000 013303 NA NA inn-co GmbH Antenna Tower Controller CO2000 017303 NA NA inn-co GmbH Turn Table TT100 TT93021703 NA NA ADT. Turn Table Controller SC100 SC93021703 NA NA ADT. NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The calibration interval of the loop antenna is 24 months and the calibrations are traceable to NML/ROC and NIST/USA. 3. The test was performed in HwaYa Chamber 3. 4. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 5. The FCC Site Registration No. is 988962. 6. The IC Site Registration No. is IC 7450F-3. Report No.: RF120629C20-4 11 of 29 Report Format Version 5.0.0

4.1.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 DEVIATION FROM TEST STANDARD No deviation. Report No.: RF120629C20-4 12 of 29 Report Format Version 5.0.0

4.1.5 TEST SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT OPERATING CONDITIONS Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF120629C20-4 13 of 29 Report Format Version 5.0.0

4.1.7 TEST RESULTS EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE 13.553 ~ 13.567MHz DETECTOR INPUT POWER 3.7Vdc Quasi-Peak FUNCTION ENVIRONMENTAL 25deg. C, 65%RH TESTED BY Chris Lin CONDITIONS ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA OPEN AT 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 13.56 54.5 124.0 -69.5 1.00 103 34.7 19.8 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. Above limits have been translated by the formula The measured field strength was extrapolated to distance 30 meters, using the formula that the limit of field strength varies as the inverse distance square (40dB per decade of distance) Example: 13.56MHz = 15848uV/m 30m = 84dBuV/m 30m = 84+20log(30/3)2 3m = 124dBuV/m Marker 1 [T1] RBW 10 kHz RF Att 0 dB Ref Lvl 54.51 dBÌ V/m VBW 30 kHz 90 dB* 13.56021042 MHz SWT 12 ms Unit dBÌ V/m 90 1 [T1] 54.51 dBÌ V/m A 13.56021042 MHz 80 2 [T1] 50.18 dBÌ V/m 13.55300000 MHz 70 3 [T1] 49.33 dBÌ V/m 13.56700000 MHz 60 IN1 1MAX 1 1MA 2 3 50 40 30 20 10 0 -10 Center 13.5596493 MHz 8 kHz/ Span 80 kHz Report No.: RF120629C20-4 14 of 29 Report Format Version 5.0.0

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE 13.553 ~ 13.567MHz DETECTOR INPUT POWER 3.7Vdc Quasi-Peak FUNCTION ENVIRONMENTAL 25deg. C, 65%RH TESTED BY Chris Lin CONDITIONS ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA CLOSE AT 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 13.56 51.8 124.0 -72.2 1.00 192 32.0 19.8 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. Above limits have been translated by the formula The measured field strength was extrapolated to distance 30 meters, using the formula that the limit of field strength varies as the inverse distance square (40dB per decade of distance) Example: 13.56MHz = 15848uV/m 30m = 84dBuV/m 30m = 84+20log(30/3)2 3m = 124dBuV/m Marker 1 [T1] RBW 10 kHz RF Att 0 dB Ref Lvl 51.84 dBÌ V/m VBW 30 kHz 90 dB* 13.55911824 MHz SWT 100 ms Unit dBÌ V/m 90 1 [T1] 51.84 dBÌ V/m A 13.55911824 MHz 80 2 [T1] 48.19 dBÌ V/m 13.55300000 MHz 70 3 [T1] 46.38 dBÌ V/m 13.56700000 MHz 60 IN1 1MAX 1MA 1 50 2 3 40 30 20 10 0 -10 Center 13.56 MHz 8 kHz/ Span 80 kHz Report No.: RF120629C20-4 15 of 29 Report Format Version 5.0.0

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE Below 30MHz DETECTOR INPUT POWER 3.7Vdc Quasi-Peak FUNCTION ENVIRONMENTAL 25deg. C, 65%RH TESTED BY Chris Lin CONDITIONS ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA OPEN AT 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 27.120 31.9 69.5 -37.6 1.00 107 11.6 20.3 ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA CLOSE AT 3m Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 27.120 31.2 69.5 -38.3 1.00 17 10.9 20.3 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: RF120629C20-4 16 of 29 Report Format Version 5.0.0

EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 FREQUENCY RANGE Below 1000MHz DETECTOR INPUT POWER 3.7Vdc Quasi-Peak FUNCTION ENVIRONMENTAL 25deg. C, 65%RH TESTED BY Chris Lin CONDITIONS ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 290.43 18.4 QP 46.0 -27.6 1.25 H 8 3.80 14.60 2 374.04 19.1 QP 46.0 -26.9 1.00 H 72 2.20 16.90 3 432.37 20.6 QP 46.0 -25.4 1.99 H 83 2.30 18.30 4 494.58 23.2 QP 46.0 -22.8 1.50 H 93 3.40 19.80 5 747.34 23.4 QP 46.0 -22.6 1.99 H 0 -0.80 24.20 6 924.27 26.4 QP 46.0 -19.6 1.00 H 155 -0.60 27.00 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION TABLE CORRECTION LIMIT ANTENNA RAW VALUE NO. FREQ. (MHz) LEVEL MARGIN (dB) ANGLE FACTOR (dBuV/m) HEIGHT (m) (dBuV) (dBuV/m) (Degree) (dB/m) 1 494.58 23.2 QP 46.0 -22.8 1.50 V 93 3.40 19.80 2 624.85 22.3 QP 46.0 -23.7 1.50 V 294 0.00 22.30 3 718.18 23.1 QP 46.0 -22.9 1.00 V 76 -0.40 23.50 4 815.39 25.5 QP 46.0 -20.5 1.99 V 261 -0.30 25.80 5 887.33 26.5 QP 46.0 -19.5 1.50 V 346 -0.20 26.70 6 955.38 27.5 QP 46.0 -18.5 1.50 V 176 0.20 27.30 REMARKS: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m). 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB). 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: RF120629C20-4 17 of 29 Report Format Version 5.0.0

4.2 CONDUCTED EMISSION MEASUREMENT 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dBµV) Quasi-peak Average 0.15 ~ 0.5 66 to 56 56 to 46 0.5 ~ 5 56 46 5 ~ 30 60 50 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.2.2 TEST INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION Test Receiver ESCS30 100289 Nov. 19, 2011 Nov. 18, 2012 ROHDE & SCHWARZ RF signal cable 5D-FB Cable-HYCO2-01 Dec. 29, 2011 Dec. 28, 2012 Woken LISN ROHDE & SCHWARZ ESH2-Z5 100100 Dec. 30, 2011 Dec. 29, 2012 (EUT) LISN ROHDE & SCHWARZ ESH3-Z5 100311 Jul. 06, 2012 Jul. 05, 2013 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 2. 3. The VCCI Site Registration No. is C-2047. Report No.: RF120629C20-4 18 of 29 Report Format Version 5.0.0

4.2.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. NOTE: All modes of operation were investigated and the worst-case emissions are reported. 4.2.4 DEVIATION FROM TEST STANDARD No deviation. 4.2.5 TEST SETUP Ve r tic a l G r o u n d R e fe r e n c e P la n e T e s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n ta l G r o u n d R e fe r e n c e P la n e N o te : 1 .S u p p o r t u n its w e r e c o n n e c te d to s e c o n d L IS N . 2 .B o th o f L IS N s ( A M N ) a r e 8 0 c m fr o m E U T a n d a t le a s t 8 0 f ro m o th e r u n its a n d o th e r m e ta l p la n e s For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT OPERATING CONDITIONS Same as 4.1.6. Report No.: RF120629C20-4 19 of 29 Report Format Version 5.0.0

4.2.7 TEST RESULTS PHASE Line 1 6dB BANDWIDTH 9kHz Emission Corr. Reading Value Limit Margin Freq. Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15000 0.15 47.85 32.91 48.00 33.06 66.00 56.00 -18.00 -22.94 2 0.18906 0.15 40.68 25.50 40.83 25.65 64.08 54.08 -23.25 -28.43 3 0.50547 0.17 37.63 30.56 37.80 30.73 56.00 46.00 -18.20 -15.27 4 0.90781 0.19 27.12 20.84 27.31 21.03 56.00 46.00 -28.69 -24.97 5 1.36328 0.22 25.67 20.57 25.89 20.79 56.00 46.00 -30.11 -25.21 6 13.55859 0.50 47.88 47.70 48.38 48.20 60.00 50.00 -11.62 -1.80 REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF120629C20-4 20 of 29 Report Format Version 5.0.0

PHASE Line 2 6dB BANDWIDTH 9kHz Emission Corr. Reading Value Limit Margin Freq. Level No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15000 0.13 49.28 34.03 49.41 34.16 66.00 56.00 -16.59 -21.84 2 0.18516 0.14 43.44 27.33 43.58 27.47 64.25 54.25 -20.67 -26.78 3 0.49766 0.16 34.98 29.19 35.14 29.35 56.04 46.04 -20.89 -16.68 4 0.90000 0.19 27.14 22.00 27.33 22.19 56.00 46.00 -28.67 -23.81 5 1.96875 0.26 18.39 13.16 18.65 13.42 56.00 46.00 -37.35 -32.58 6 13.56003 0.57 47.10 46.91 47.67 47.48 60.00 50.00 -12.33 -2.52 REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF120629C20-4 21 of 29 Report Format Version 5.0.0

4.3 FREQUENCY STABILITY 4.3.1 LIMITS OF FREQUENCY STABILITY MEASUREMENT The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency over a temperature variation of –20 degrees to 50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 90% to 110% of the rated supply voltage at a temperature of 20 degrees C. 4.3.2 TEST INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION SPECTRUM ANALYZER FSP40 100039 Feb. 03, 2012 Feb. 02, 2013 R&S WIT STANDARD TEMPERATURE AND TH-4S-C W981030 Jun. 13, 2012 Jun. 12, 2013 HUMIDITY CHAMBER NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.3.3 TEST PROCEDURE a. The EUT was placed inside the environmental test chamber and powered by nominal DC voltage. b. Turn the EUT on and couple its output to a spectrum analyzer. c. Turn the EUT off and set the chamber to the highest temperature specified. d. Allow sufficient time (approximately 30 min) for the temperature of the chamber to stabilize, turn the EUT on and measure the operating frequency after 2, 5, and 10 minutes. e. Repeat step 2 and 3 with the temperature chamber set to the lowest temperature. f. The test chamber was allowed to stabilize at +20 degree C for a minimum of 30 minutes. The supply voltage was then adjusted on the EUT from 85% to 115% and the frequency record. Report No.: RF120629C20-4 22 of 29 Report Format Version 5.0.0

4.3.4 DEVIATION FROM TEST STANDARD No deviation. 4.3.5 TEST SETUP Temperature Spectrum Analyzer DC Power Supply 4.3.6 EUT OPERATING CONDITION Same as Item 4.1.6. Report No.: RF120629C20-4 23 of 29 Report Format Version 5.0.0

4.3.7 TEST RESULTS FREQUEMCY STABILITY VERSUS TEMP. 0 MINUTE 2 MINUTE 5 MINUTE 10 MINUTE POWER TEMP. Measured Frequency Measured Frequency Measured Frequency Measured Frequency SUPPLY (℃) Frequency Drift Frequency Drift Frequency Drift Frequency Drift (Vdc) (MHz) % (MHz) % (MHz) % (MHz) % 50 5.0 13.559749 -0.0018523 13.559750 -0.0018467 13.559768 -0.0017114 13.559769 -0.0017035 40 5.0 13.559793 -0.0015252 13.559817 -0.0013474 13.559799 -0.0014859 13.559782 -0.0016077 30 5.0 13.559730 -0.0019916 13.559739 -0.0019263 13.559722 -0.0020499 13.559709 -0.0021460 20 5.0 13.560107 0.0007868 13.560122 0.0009016 13.560134 0.0009882 13.560137 0.0010103 10 5.0 13.559732 -0.0019737 13.559780 -0.0016226 13.559762 -0.0017551 13.559728 -0.0020059 0 5.0 13.559740 -0.0019153 13.559740 -0.0019148 13.559708 -0.0021532 13.559726 -0.0020206 -10 5.0 13.559815 -0.0013624 13.559813 -0.0013761 13.559816 -0.0013572 13.559789 -0.0015560 -20 5.0 13.559794 -0.0015197 13.559817 -0.0013517 13.559783 -0.0016008 13.559800 -0.0014749 FREQUEMCY STABILITY VERSUS VOLTAGE 0 MINUTE 2 MINUTE 5 MINUTE 10 MINUTE TEMP. POWER Measured Frequency Measured Frequency Measured Frequency Measured Frequency SUPPLY (℃) (Vdc) Frequency Drift Frequency Drift Frequency Drift Frequency Drift (MHz) % (MHz) % (MHz) % (MHz) % 5.75 13.560129 0.0009539 13.560139 0.0010281 13.560143 0.0010519 13.560151 0.0011154 20 5.0 13.560107 0.0007891 13.560122 0.0008997 13.560134 0.0009882 13.560137 0.0010103 4.25 13.559696 -0.0022423 13.559700 -0.0022137 13.559705 -0.0021724 13.559718 -0.0020796 Report No.: RF120629C20-4 24 of 29 Report Format Version 5.0.0

4.4 20dB BANDWIDTH 4.4.1 LIMITS OF 20dB BANDWIDTH MEASUREMENT The 20dB bandwidth shall be specified in operating frequency band. 4.4.2 TEST INSTRUMENTS Same as Item 4.1.2. 4.4.3 TEST PROCEDURE The bandwidth of the fundamental frequency was measured by spectrum analyzer with 1kHz RBW and 1kHz VBW. The 20dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 20dB. 4.4.4 DEVIATION FROM TEST STANDARD No deviation. 4.4.5 TEST SETUP Same as Item 4.1.5. 4.4.6 EUT OPERATING CONDITION Same as Item 4.1.6. Report No.: RF120629C20-4 25 of 29 Report Format Version 5.0.0

4.4.7 TEST RESULTS Operating 20dBc point (Low) 20dBc point (HIGH) frequency band PASS/FAIL (MHz) 13.558 MHz 13.561 MHz 13.553~13.567 PASS Marker 1 [T1] RBW 1 kHz RF Att 0 dB Ref Lvl 53.81 dBÌ V/m VBW 3 kHz 90 dB* 13.55961924 MHz SWT 150 ms Unit dBÌ V/m 90 1 [T1] 53.81 dBÌ V/m A 13.55961924 MHz 80 2 [T1] 34.40 dBÌ V/m 13.55791583 MHz 70 3 [T1] 34.12 dBÌ V/m 13.56130261 MHz 60 IN1 1MAX 1 1MA D1 53.7 5 dB* 50 40 2 3 D2 33.7 dB* 30 20 10 0 F2 F1 -10 Center 13.5596493 MHz 1 kHz/ Span 10 kHz Report No.: RF120629C20-4 26 of 29 Report Format Version 5.0.0

5. PHOTOGRAPHS OF THE TEST CONFIGURATION Please refer to the attached file (Test Setup Photo). Report No.: RF120629C20-4 27 of 29 Report Format Version 5.0.0

6. INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. Report No.: RF120629C20-4 28 of 29 Report Format Version 5.0.0

7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications are made to the EUT by the lab during the test. --- END --- Report No.: RF120629C20-4 29 of 29 Report Format Version 5.0.0


Document Created: 2012-10-25 19:10:40
Document Modified: 2012-10-25 19:10:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC