RF Test Report

FCC ID: QYLGET101U

Test Report

Download: PDF
FCCID_4276104

( nt' Report Number: 1904FR13 \-’ Rev.01 RF Test Report Applicant : Getac Technology Corporation Product Type : Digitizer module Trade Name : EMRight Model Number i GET—A01 Test Specification : FCC 47 CFR PART 15 SUBPART C ANSI €63.10:2013 Receive Date : Mar. 08, 2019 Test Period : Mar. 26 ~ Mar. 27, 2019 Issue Date : May 03, 2019 Issue by A Test Lab Techno Corp. No. 140—1, Changan Street, Bade District, NC . 33465, Taiwan Taocyuan City . (R.O.C.) <=""* iBenck > m\a Tel : +886—3—2710188 / Fax : +886—3—2710190 Pss o * S Taiwan Accreditation Foundation accreditation number: 1330 Test Firm MRA designation number: TWOO010 Note: This report shall not. be reproduced except in full, without the written approval of A Test Lab Techno Corp.. This document may be altered or revised by A Test. Lab Techno.Corp. personnel only, and shall be noted in the revision section. of the.document. The. client should not.use it to claim product endorsement by TAF, or any government agencies..The test results in the report only apply to the tested sample. 1 of 26

Report Number: 1904FR13 Rev.01 Revision History Rev. Issue Date Revisions Revised By 00 Apr. 11, 2019 Initial Issue Nina Lin Page 22 & 25 Radiated Emission Added Test 01 May 03, 2019 Nina Lin Photographs 2 of 26

@l Report Number: 1904FR13 Rev.01 Verification of Compliance Issued Date: May 03, 2019 Applicant Getac Technology Corporation Product Type Digitizer module Trade Name EMRight Model Number GET—101 FCC ID QYLGETIO1U EUT Rated Voltage DC 3.7 V Test Voltage 120 Vac / 60 Hz Applicable Standard FCC 47 CFR PART 15 SUBPART C ANSI C€63.10:2013 Test Result Complied Performing Lab. A Test Lab Techno Corp. s\ ('.AT: No. 140—1, Changan Street, Bade District, 1laE=MRA \) Taoyuan City 33465, Taiwan (R.O0.C.) TffyS s Tel : +886—3—2710188 / Fax : +886—3—2710190 Taiwan Accreditation Foundation accreditation number: 1330 http //Avww.atl—lab.com.tw/e—index.htm A Test Lab Techno Corp. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by A Test Lab Techno Corp. based on interpretations and/or observations of test results. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. j [ Approved By : t "\y t/U\ Reviewed By :Ek(’c Qu %/ g (Manager) (Fly Lu) (Testing Engineer) (Eric Ou Yang) 3 of 26

Report Number: 1904FR13 Rev.01 TABLE OF CONTENTS 1 General Information ................................................................................................... 5 1.1. Summary of Test Result ....................................................................................... 5 1.2. Measurement Uncertainty .................................................................................... 5 2 EUT Description ......................................................................................................... 6 3 Test Methodology ...................................................................................................... 7 3.1. Mode of Operation ............................................................................................... 7 3.2. EUT Test Step ...................................................................................................... 7 3.3. Configuration of Test System Details ................................................................... 8 3.4. Test Instruments ................................................................................................ 10 3.5. Test Site Environment ........................................................................................ 10 4 Measurement Procedure ......................................................................................... 11 4.1. AC Power Line Conducted Emission Measurement .......................................... 11 4.2. Radiated Emission Measurement ...................................................................... 13 4.3. 20 dB Bandwidth ................................................................................................ 18 4.4. Antenna Requirement ........................................................................................ 19 5 Test Results ............................................................................................................. 20 Annex A. Conducted Emission................................................................................... 20 Annex B. 20 dB Bandwidth ........................................................................................ 22 Annex C. Radiated Emission Measurement .............................................................. 23 4 of 26

Report Number: 1904FR13 Rev.01 1 General Information 1.1. Summary of Test Result Standard Item Result Remark 15.207(a) Conducted Emissions Voltage PASS --- 15.209 Radiated Emission Limits PASS --- 15.215 (c) 20 dB Bandwidth PASS --- 15.203 Antenna Requirement PASS --- The test results of this report relate only to the tested sample(s) identified in this report. Standard Description CFR47, Part 15, Subpart C Intentional Radiators American National Standard of Procedures for Compliance ANSI C63. 10: 2013 Testing of Unlicensed Wireless Devices 1.2. Measurement Uncertainty Test Item Frequency Range Uncertainty 9 kHz ~ 150 kHz 2.7 Conducted Emission 150 kHz ~ 30 MHz 2.7 9 kHz ~ 30 MHz 1.7 30 MHz ~ 1000 MHz 5.7 Radiated Emission 1000 MHz ~ 18000 MHz 5.5 18000 MHz ~ 26500 MHz 4.8 26500 MHz ~ 40000 MHz 4.8 RF Bandwidth 4.96 % 5 of 26

@l Report Number: 19047R 13 Rev.01 2 EUT Description Getac Technology Corporation Aoplicant 5F.Building A,No.200.Se0.1 Nanganq..Rd.. Taipei City, 11568, Talwan EMRint Manufacturer 5F—11, No.18, Tai Yuen St., Jubel City, Hsinchu County 30265, Taiwan, Product Digtizer module Trade Name EMRiant Model Number cet—101 ree p avieerionu Frequency Range 510.0 kiz Modulation Type Pom Number of Channels 1 Channel Antenna Type Loop Antenna Operate Temp. Range ~10 ~ +70 °C 6 of 26

( ntl Report Number: 19047R 13 \_4 Rev.o1 3 Test Methodology 3.1. Mode of Operation Thefollowing test mode(s) were scanned during the preliminary test : Pre—Test Mode Mode 1: Transmit Mode ATL has veriied the construction and function in typical operation. All the test modes were carried out with the EUT in normal aperation 3.2. EUT Test Step 1 Setup the EUT shown on "Configuration of Test System Details® 2. Turn on the power of all equipment 3 The EUT will start to operate function Measurement Sotwere No. Description version 1| Conducted Emission 1143 2| Reiated Emission n144 7 of 26

Report Number: 1904FR13 Rev.01 3.3. Configuration of Test System Details Conducted Emission AC Input (8)Tablet (7) (1) HDMI Cable (5)AC Adapter (6) Monitor Digitizer Pen EUT (Optional) (2) Mouse (4)SD Card (3) Earphone & Microphone Radiated Emission AC Input (8)Tablet (6) (5)AC Adapter Digitizer Pen EUT (Optional) (4)SD Card 8 of 26

Report Number: 1904FR13 Rev.01 Devices Description Product Manufacturer Model Number Serial Number Power Cord CN-0D3C8Y-74261-5 (1) Monitor DELL P2415Qb --- 23-0HUL (2) Mouse Logitech M-UAG96B --- --- Earphone & (3) HTC --- --- --- Microphone (4) SD Card Transcend --- --- --- (5) AC adapter FSP FSP065-RBBN3 --- --- Digitizer Pen (6) (Optional) EMRight GET-101 --- --- (7) HDMI Cable Avier K48GHS --- (8) Tablet Getac UX10 --- 9 of 26

Report Number: 1904FR13 Rev.01 3.4. Test Instruments For Conducted Emission Test Period: Mar. 27, 2019 Equipment Manufacturer Model Number Serial Number Cal. Date Cal. Period Test Receiver R&S ESCI 100367 05/21/2018 1 year LISN R&S ENV216 101040 04/11/2018 1 year RF Cable Woken 00100D1380194M TE-02-03 05/17/2018 1 year Test Site ATL TE02 TE02 N.C.R. ----- For Radiated Emissions / Conducted Test Period: Mar. 26, 2019 Equipment Manufacturer Model Number Serial Number Cal. Date Cal. Period Spectrum Analyzer Keysight N9010A MY52221312 01/14/2019 1 year (10 Hz~44 GHz) Pre Amplifier Agilent 8447D 2944A11119 01/14/2019 1 year (100 kHz~1.3 GHz) Broadband Antenna Schwarzbeck VULB9168 416 10/19/2018 1 year Loop Antenna Electro-Metrics EMCI-LPA600 277 04/19/2018 1 year RF Cable EMCI EMC104-N-N-6000 TE01-1 02/20/2019 1 year EMC104-SM-SM-1 Microwave Cable EMCI 170814 10/30/2018 1 year 3000 EMC102-KM-KM-1 Microwave Cable EMCI 151001 02/20/2019 1 year 4000 Note: N.C.R. = No Calibration Request. 3.5. Test Site Environment Items Required (IEC 60068-1) Actual Temperature (C) 15-35 26 Humidity (%RH) 25-75 60 Barometric pressure (mbar) 860-1060 990 10 of 26

Report Number: 1904FR13 Rev.01 4 Measurement Procedure 4.1. AC Power Line Conducted Emission Measurement  Limit Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 to 56 56 to 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50  Test Setup 11 of 26

( ntl Report Number: 19047R 13 \.; Rev.o1 m Test Procedure The EUT and simulaters are connected to the main power through a line impedance stabilization network (L.LSN.). This provides a 50. / 50 uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50. 27 50 uH coupling impedance with 50 ohm termination Tabletop deviceshall be placed on a non—conducing pletform, of nominal size 1 m by 1.5 m, raised 80 om sbove the reference ground plane. The wall of screened room shall be Iocated 40 on to the rearof the EUT. Other surfaces of tabletop or foor standing EUT shall be at least 80 om from any other ground conducting surface incluing one or more LISNs. For foor—standing device shall be placed under the EUT with a 12 mm insulstng materia Conducted emissions were investigated over the frequency range from 0.15 MHz to 30 Mz using a resalution bandwith of 8 kHz. The equipment under test (EUT) shall be meet the limits in section 4.1, as applicable, including the everage limit and the quasi—peak limit when using respectively. an everage detector and quasi—pesk detector measured in sccordance with the methods described of related standard. When all of pesk value were complied with quasi—peak and average limit rom 150 kz to 30 MHz then quasi—peak and average measurement was unnecessery The AVN shall be placed 0.8 m from the boundary ofthe un‘ under test and banded to a ground reference plane for AMNs mounted on top ofthe ground reference plane. This distance is between the closest points of the AVMN and the EUT. Allother units of the EUT and essociated equipment shall be at least 0.8 m from the ANVN. If the mains power cable is longer than 1 m then the cable shall be folded back and forth at the centre of the lead to form a bundle no longer than 0.4 m. All ofinterconnecting cables that hang closer than 40 om to the ground plane shall be folded back and forth in the center forming a bundle 30 om to 40 om lang. All of EUT and AE shall be sepsrate place more then 0.1 m. All50 O ports ofthe LISN shallbe resistvely terminated into 50 0 loads when not connected to the measuring instrument If the reading of the measuring receiver shows futustions close to the limit,the reading shall be observed for at least 155 at each measurement frequency,the higher reading shallbe recorded with the exception of any brief isolated high reading which shall be ignored 12 of 26

Report Number: 1904FR13 Rev.01 4.2. Radiated Emission Measurement  Limit (a) Except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: (b) In the emission table above, the tighter limit applies at the band edges. (c) The level of any unwanted emissions from an intentional radiator operating under these general provisions shall not exceed the level of the fundamental emission. For intentional radiators which operate under the provisions of other sections within this part and which are required to reduce their unwanted emissions to the limits specified in this table, the limits in this table are based on the frequency of the unwanted emission and not the fundamental frequency. However, the level of any unwanted emissions shall not exceed the level of the fundamental frequency. (d) The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. (e) The provisions in §§15.31, 15.33, and 15.35 for measuring emissions at distances other than the distances specified in the above table, determining the frequency range over which radiated emissions are to be measured, and limiting peak emissions apply to all devices operated under this part. (f) In accordance with §15.33(a), in some cases the emissions from an intentional radiator must be measured to beyond the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator because of the incorporation of a digital device. If measurements above the tenth harmonic are so required, the radiated emissions above the tenth harmonic shall comply with the general radiated emission limits applicable to the incorporated digital device, as shown in §15.109 and as based on the frequency of the emission being measured, or, except for emissions contained in the restricted frequency bands shown in §15.205, the limit on spurious emissions specified for the intentional radiator, whichever is the higher limit. Emissions which must be measured above the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator and which fall within the restricted bands shall comply with the general radiated emission limits in §15.109 that are applicable to the incorporated digital device. (g) Perimeter protection systems may operate in the 54-72 MHz and 76-88 MHz bands under the provisions of this section. The use of such perimeter protection systems is limited to industrial, business and commercial applications. 13 of 26

Report Number: 1904FR13 Rev.01 Frequency Field Strength Measurement Distance (MHz) (μV/m at meter) (meter) 0.009 – 0.490 2400 / F (kHz) 300 0.490 – 1.705 24000 / F (kHz) 30 1.705 – 30.0 30 30 30 - 88 100** 3 88-216 150** 3 216-960 200** 3 Above 960 500 3 ** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 14 of 26

Report Number: 1904FR13 Rev.01  Setup 9 kHz ~ 30 MHz 30 MHz ~ 1 GHz Antenna tower 3m Bilog antenna EUT 4m Spectrum / Receiver Turntable 1m 0.8m Pre-amp Reference ground plane 15 of 26

Report Number: 1904FR13 Rev.01  Test Procedure Final radiation measurements were made on a three-meter Semi Anechoic Chamber. The EUT system was placed on a nonconductive turntable which is 0.8 meters height, top surface 1.0 x 1.5 meter. The spectrum was examined from 3 Hz to 44 GHz in order to cover the whole spectrum below 10th harmonic which could generate from the EUT. During the test, EUT was set to transmit continuously. For measurements below 1 GHz the resolution bandwidth is set to 100 kHz for peak detection measurements or 120 kHz for quasi-peak detection measurements. Peak detection is used unless otherwise noted as quasi-peak. For measurements above 1 GHz the resolution bandwidth is set to 1 MHz, and then the video bandwidth is set to 3 MHz for peak measurements and 10 Hz for average measurements. A nonconductive material surrounded the EUT to supporting the EUT for standing on tree orthogonal planes. At each condition, the EUT was rotated 360 degrees, and the antenna was raised and lowered from one to four meters to find the maximum emission levels. Measurements were taken using both horizontal and vertical antenna polarization. Broadband/Horn Antenna were used in frequency 30 MHz to 18 GHz at a distance of 3 meter. Loop/Horn Antenna was used in frequency 9 kHz to 30 MHz and 18 to 26.5 GHz at a distance of 1 meter. All test results were extrapolated to equivalent signal at 3 meters utilizing an inverse linear distance extrapolation Factor (20 dB/decade). For testing above 1 GHz, the emission level of the EUT in peak mode was 20 dB lower than average limit (that means the emission level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. Appropriate preamplifiers were used for improving sensitivity and precautions were taken to avoid overloading or desensitizing the spectrum analyzer. No post – detector video filters were used in the test. The spectrum analyzer’s 6 dB bandwidth was set to 1 MHz, and the analyzer was operated in the peak detection mode, for frequencies both below and up 1 GHz. The average levels were obtained by subtracting the duty cycle correction factor from the peak readings. The following procedures were used to convert the emission levels measured in decibels referenced to 1 microvolt (dBuV) into field intensity in microvolt pre-meter (uV/m). The actual field intensity in decibels referenced to 1 microvolt in to field intensity in microvolt per-meter (dBuV/m). 16 of 26

Report Number: 1904FR13 Rev.01 The actual field is intensity in referenced to 1 microvolt per meter (dBuV/m) is determined by algebraically adding the measured reading in dBuV, the antenna factor (dB), and cable loss (dB) and Subtracting the gain of preamplifier (dB) is auto calculate in spectrum analyzer. (1) Amplitude (dBuV/m) = FI (dBuV) +AF (dBuV) +CL (dBuV)-Gain (dB) FI= Reading of the field intensity. AF= Antenna factor. CL= Cable loss. P.S Amplitude is auto calculate in spectrum analyzer. (2) Actual Amplitude (dBuV/m) = Amplitude (dBuV)-Dis(dB) The FCC specified emission limits were calculated according the EUT operating frequency and by following linear interpolation equations: (a) For fundamental frequency : Transmitter Output < +30 dBm (b) For spurious frequency : Spurious emission limits = fundamental emission limit /10 Data of measurement within this frequency range without mark in the table above means the reading of emissions are attenuated more than 20 dB below the permissible limits or the field strength is too small to be measured. 17 of 26

Report Number: 1904FR13 Rev.01 4.3. 20 dB Bandwidth  Limit N/A  Test Setup Spectrum Analyzer RF Cable EUT  Test Procedure The bandwidth of the fundamental frequency was measured by spectrum analyzer with 1 kHz RBW and 3 kHz VBW. 18 of 26

Report Number: 1904FR13 Rev.01 4.4. Antenna Requirement  Require An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited.  Antenna Connector Construction See section 2 – antenna information. 19 of 26

' ntl Report Number: 1904FR13 \.I Rev.01 5 Test Results Annex A Conducted Emission Standard: FCC Part 15.247 Line: L1 Testitem: Conducted Emission Power: AC 120 Vieo He Test Mode: Mode 1 Temp.{C)/Hum.(KRH): 26(C)/60 RH Description: ma ow Linit1 — ao 00 8150 a5 thlta s 30 000 No.| Frequency| OP AVG Correction| QP ave or ave op AVG Remark reading reading factor resut resut im lt margin margin im (Bay (euy i9 (eay |uy ces ce| 3 (a8) 1| oiseo sers 1279 as2 «seo zes esze sere 1988 3347 Pass 2 orsoo sres 2a7s as2 aras ss2s ceoe seoe 1089 2070 Pass s ozeo seos 19e0 as2 «sar zore esar soar 1780 2428 Pass « omseo saes i8eo as2 «reo mmzr ereo steo 1940 2308 Pass s oaseo s2ar is as2 ereo ms«s enes stes 1978 2320 Pass s neme zero 1747 a.c0 seso 2ror seoo «800 —2170 1888 Pass Note: 1. Result (dBuVim) = Correct Factor (dB/m) + Reading(dBu\). 2.Correction factor (dB) = Cable loss (dB) + L.L.S.N. factor (dB). 20 of 26

' ntl Report Number: 1904FR13 \.I Rev.01 Standard: FCC Part 16.247 Line: N Testitem: Conducted Emission Power: AC 120 VIBO Hz Test Mode: Mode 1 Temp.(C)/Hum.(KRH): 26(C)!60 RH Description: ma ow Linit1 — Lint2 — 2 1 s 6 an 00 8150 a5 thlta s 30 000 No.| Frequency| OP AVG Correction| QP ave or ave op AVG Remark reading reading factor resut resut im lt margin margin mim @eay ce|_ i9 es ce| ce| cem 3 (a8) 1| oisso ssas ree se0 «sas riso essr sser 2000 3308 Pass 2 orseo sasr 1088 seo «si2 z4s esas ssas 2208 3470 Pass s orsm ssre 20ss oso «sas sore eeso seso 1908 2428 Pass « oreeo sero 2202 oso «aze srer eses soes 1907 2148 Pass s ozieo 2069 se3 a.se seme reme saos saos —2e77 8388 Pass s oaseo sose 18e3 sso soos resr enes stes 2188 281 Pass Note: 1. Result (dBuVim) = Correct Factor (dB/m) + Reading(dBu\). 2.Correction factor (dB) = Cable loss (dB) + L.L.S.N. factor (dB). 21 of 26

Report Number: 1904FR13 Rev.01 Annex B. 20 dB Bandwidth Test Mode Mode 1 Frequency 20 dB Bandwidth (kHz) (kHz) 510.6 30.84  Test Graphs 22 of 26

@l Report Number: 19047R 13 Rev.01 Annex C. Radiated Emission Measurement Harmonic 9 kHz~ 30 MHz: Standard FCC Part 15.200 Test Distance 1 m Testtem Harmonic Power Ac 120 viso He Test Mode Mode 1 Temp (C)/Hum (RH}: 28(‘C)60 RH Ant Polar Horizontal imo_mors ~ts=p—y— Te 1 wioun: _ 1 £4o% i1O _1 1 1 m on am wo sw en e am~sree ie oo are «s Freauency Resding: CoreetFector Near—Field Esuy Derived value Limt Merain __ (Miz) (dguv) (d8/m) (dBu¥im) |_(4Buv) (dBu¥im) |_(d8) 1 astos 24e3 4500 re.r2 1076 sase —2269 ar 2 12086 aa 02 «061 73e3 1278 rssa —r258 ar 3 « ost? 1256 ar.0s so.c0 —a88 rase —20.00 ar 4 sear ass ara> aros ars rase 827 ar s 7eser 115 aree sa.o —s.8 rase —s8.20 ar s s o7ee o2 ar se 28 2o sss rase —ss.09 ar ote: he Tevel is maasured at 1 meter and is converted mnto result at 300 or 30 meter The converted formula listed below Measure result (1 meter distance); a Compute result (30 meter distance}; A 0 neartus =N2TT * dnsasue = 1 meter distance As ~ 40"100(Choar e AOneasare) = 20"109(Chrae! Cleatd ex. a = 79.72 dBuV, A=79.72 — 4010g(@8 53 /1 ) — 20"log(20 /93 53 ) dBu¥ = 10.76 dBuy 23 of 26

@l Report Number: 19047R 13 Rev.o1 Standerd FCC Port 15.200 Test Distance 1m Testtem Hermonic Power Ac 120 vieo He Test Mode Mode 1 Temp (C)}Hum (GGRH): 26(‘cy80 RH Ant Polar vertical im _anra —— 1 youn: m | r m 4 ; | | x son <sor oo in emr n m n c o wne Frequency Reading CoreetFactor NEBrFie!d Derived Limit Mergin No Result Value Remark (uile) (deuv) (dB/m) (dBuvim) |_(4Buv) (dBuvim) |_(dB) 1 a.stos sa.72 45 00 a181 1285 sase 2000 or 2 12550 2220 «o 67 T2or mon rsse 1962 |__or 3 s 208 as2 ar or 4300 —8.00 rase sese or a s core 1255 a7 05 a001 —1se rase s108 or s Toser 116 ar e s 20 —s05 rase se10 |__or a s ore« 126 ar se sa e s21 rase srs or Note: The Teval is measured at 1 meter and is converted into resul at 300 or 30 meter 24 of 26

' ntl Report Number: 1904FR13 \’ Rev.01 30 MHz~ 1 GHz: Standard: FCC Part 15.209 Test Distance: 3m Testitem: Harmonic Power: AC 120 Vieo He Test Mode: Mode 1 Temp.(C)/Hum.(KRH): 26(C)/60 RH AntPolar.: Horizontal 90.0 @W/n Te Horgin — 1 ’—‘ 4 s 30000 12700 22400 321.00 410.00 51500 61200 708.00 an6 00 1000.00 Mlte «. Frequency Reading Correct Factor Result Limit Margin Remark (MHz) (dBuyy (dBim) (dBu¥Vim} (dBuVim) (dB) 1 23.0500 s8.55 41184 2e.m 4350 —16.70 or 2 soo.es00 a0.99 .72 20.27 46.00 41573 or a see.5200 35.66 321 2245 46.00 1355 or 4 s29.5500 28.70 0.72 2042 46.00 1658 or s Tor0o 20.22 4.70 a2.02 46.00 —13.08 or e Tr1.0800 28.68 5.87 24.55 46.00 41145 or Note:1. Result(dBuVim) = Correct Factor (dB/m) + Reading(dBu\) Example: 28.71=—1.84438 55 2Correction factor (dB/m) = Antenna Factor (dBfm) + Cable loss (d8) — Pre—Amplifier gain (dB) 3. When the peak resultsare less than average Iimit, so not need to evaluate the average 25 of 26

' ntl Report Number: 1904FR13 \’ Rev.01 Standard: FCC Part 16.209 Test Distance: 3m Testitem: Harmonic Power: AC 120 VIBO Hz Test Mode: Mode 1 Temp.(C)/Hum.(KRH): 26(C)!60 RH Ant.Polar.: Vortical s00 dtw/m Tmit: — Main — ao 10 30000 127.0 220 321.00 4100 $15.00 61200 70800 806 00 1000.00 Wtte «. Frequency Reading CorrectFactor Result Limit Margin Remark (MHz) (dBuyy (dBim) (dBu¥Vim} (dBu¥Vim) (dB) 1 23.0500 40.10 41184 28.26 4350 41524 or 2 189.7800 a1.39 772 2067 4350 1983 or a 445.1800 28.50 —047 2812 46.00 1788 or 4 s20.8200 26.59 o.5e a7s 46.00 285 or s seo.ee00 s2.19 223 2442 46.00 —11.58 or e T7e.9000 20.40 5.97 3537 46.00 1063 or Note:1. Result(dBuVim) = Correct Factor (dB/m) + Reading(dBu\) Example: 28.28=—1.84+40.10 2Correction factor (dB/m) = Antenna Factor (dBfm) + Cable loss (d8) — Pre—Amplifier gain (dB) 3. When the peak results are less than average imso not need to evaluate the average 26 of 26


Document Created: 2019-05-21 06:01:31
Document Modified: 2019-05-21 06:01:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC