RF Test Report-BLE

FCC ID: QYL8260NG

Test Report

Download: PDF
FCCID_4083190

Variant FCC Test Report Report No.: RF151207C04A-1 FCC ID: QYL8260NG Test Model: 8260NGW Received Date: Sep. 07, 2018 Test Date: Oct. 01, 2018 ~ Oct. 04, 2018 Issued Date: Oct. 30, 2018 Applicant: Getac Technology Corporation. Address: 5F., Building A, No. 209, Sec.1, Nangang Rd.,Nangang Dist., Taipei City 11568, Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) Test Location: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan, R.O.C. FCC Registration / 788550 / TW0003 Designation Number: This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF151207C04A-1 Page No. 1 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ........................................................................................................................... 4 2 Summary of Test Results ........................................................................................................................... 5 2.1 Measurement Uncertainty ..................................................................................................................... 5 2.2 Modification Record .............................................................................................................................. 5 3 General Information ................................................................................................................................... 6 3.1 General Description of EUT .................................................................................................................. 6 3.2 Description of Test Modes..................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 8 3.3 Description of Support Units ................................................................................................................. 9 3.3.1 Configuration of System under Test ........................................................................................... 9 3.4 General Description of Applied Standards ............................................................................................ 9 4 Test Types and Results ............................................................................................................................ 10 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 10 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 10 4.1.2 Test Instruments ........................................................................................................................ 11 4.1.3 Test Procedures ........................................................................................................................ 12 4.1.4 Deviation from Test Standard ................................................................................................... 12 4.1.5 Test Set Up ............................................................................................................................... 13 4.1.6 EUT Operating Conditions ........................................................................................................ 14 4.1.7 Test Results .............................................................................................................................. 15 4.2 Conducted Emission Measurement .................................................................................................... 20 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 20 4.2.2 Test Instruments ....................................................................................................................... 20 4.2.3 Test Procedures ........................................................................................................................ 20 4.2.4 Deviation from Test Standard ................................................................................................... 21 4.2.5 Test Setup ................................................................................................................................. 21 4.2.6 EUT Operating Conditions ........................................................................................................ 21 4.2.7 Test Results .............................................................................................................................. 22 4.3 Conducted Output Power Measurement ............................................................................................ 24 4.3.1 Limits of Conducted Output Power Measurement.................................................................... 24 4.3.2 Test Setup ................................................................................................................................. 24 4.3.3 Test Instruments ....................................................................................................................... 24 4.3.4 Test Procedures ........................................................................................................................ 24 4.3.5 Deviation from Test Standard ................................................................................................... 24 4.3.6 EUT Operating Conditions ........................................................................................................ 24 4.3.7 Test Results .............................................................................................................................. 24 5 Pictures of Test Arrangements................................................................................................................ 25 Appendix – Information on the Testing Laboratories ................................................................................ 26 Report No.: RF151207C04A-1 Page No. 2 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

Release Control Record Issue No. Description Date Issued RF151207C04A-1 Original Release Oct. 30, 2018 Report No.: RF151207C04A-1 Page No. 3 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

1 Certificate of Conformity Product: Wireless module Brand: Intel Test Model: 8260NGW Sample Status: Engineering Sample Applicant: Getac Technology Corporation. Test Date: Oct. 01, 2018 ~ Oct. 04, 2018 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247) ANSI C63.10:2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Oct. 30, 2018 Gina Liu / Specialist Approved by : , Date: Oct. 30, 2018 Dylan Chiou / Project Engineer Report No.: RF151207C04A-1 Page No. 4 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.247) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission Pass Minimum passing margin is -21.69 dB at 1.22916 MHz. Meet the requirement of limit. 15.205 & 209 Radiated Emissions Pass Minimum passing margin is -3.1 dB at 2363.06 MHz. 15.247(d) Band Edge Measurement N/A Refer to Note 15.247(d) Antenna Port Emission N/A Refer to Note 15.247(a)(2) 6 dB Bandwidth N/A Refer to Note --- Occupied Bandwidth Measurement N/A Refer to Note 15.247(b) Conducted Power Pass Meet the requirement of limit. 15.247(e) Power Spectral Density N/A Refer to Note 15.203 Antenna Requirement N/A Refer to Note Note: Only Conducted Emission, Conducted Power and Radiated Emissions tests were performed for the addendum. Refer to original report for other test data. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expended Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150 kHz ~ 30 MHz 2.44 dB 30 MHz ~ 200 MHz 2.93 dB Radiated Emissions up to 1 GHz 200 MHz ~ 1000 MHz 2.95 dB 1 GHz ~ 18 GHz 2.26 dB Radiated Emissions above 1 GHz 18 GHz ~ 40 GHz 1.94 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF151207C04A-1 Page No. 5 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

3 General Information 3.1 General Description of EUT Product Wireless module Brand Intel Test Model 8260NGW Status of EUT Engineering Sample Power Supply Rating 5.0 Vdc (host equipment) Modulation Type GFSK Transfer Rate 1 Mbps Operating Frequency 2402 ~ 2480 MHz Number of Channel 40 Output Power 9.183 mW Antenna Type PIFA antenna with -0.14 dBi gain Antenna Connector I-pex Accessory Device Refer to Note as below Data Cable Supplied Refer to Note as below Note: 1. This report is issued as a supplementary report to BV CPS report no. RF151207C04-3. The difference compared with original report is adding new WLAN antenna, PCMCIA card slot, new SSD and new adapter. Therefore, only Conducted Emission, Conducted Power and Radiated Emissions tests were verified and recorded in this report. 2. The EUT is authorized for use in specific End-product. Product Brand Model Description NB & Tablet Getac V110 N/A 3. The End-product contains following accessory devices. (New brand is marked in gray.) Product Brand Model Description I/P: 100-240Vac, 50/60Hz, 1.7A Adapter 1 Chicony A12-065N2A O/P: 19Vdc, 3.42A 1.7 m shielded with 1 core I/P: 100-240Vac, 50/60Hz, 1.5A Adapter 2 N/A ADM-9019M O/P: 19Vdc, 4.74A 1.75 m shielded without core Battery Getac Technology Corp. BP3S1P2100-S 11.1Vdc, 2100mAh WLAN/BT Module Intel 8260NGW -- Digitizer KYE T116 EMR Digitizer -- Function: WWAN LTE Module Sierra EM7355 SW: SWI9X15C_01.05.11.08 HW: 1.1 OS N/A N/A Win10 64bit 4. The above EUT information is declared by manufacturer and for more detailed features description, please refers to the manufacturer's specifications or User's Manual. Report No.: RF151207C04A-1 Page No. 6 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

3.2 Description of Test Modes 40 channels are provided to this EUT: Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) 0 2402 10 2422 20 2442 30 2462 1 2404 11 2424 21 2444 31 2464 2 2406 12 2426 22 2446 32 2466 3 2408 13 2428 23 2448 33 2468 4 2410 14 2430 24 2450 34 2470 5 2412 15 2432 25 2452 35 2472 6 2414 16 2434 26 2454 36 2474 7 2416 17 2436 27 2456 37 2476 8 2418 18 2438 28 2458 38 2478 9 2420 19 2440 29 2460 39 2480 Report No.: RF151207C04A-1 Page No. 7 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable To Description Mode RE1G RE<1G PLC APCM - √ √ √ √ - Where RE1G: Radiated Emission above 1 GHz RE<1G: Radiated Emission below 1 GHz PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement Note: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Y-plane. Note: “-”means no effect. Radiated Emission Test (Above 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 0, 19, 39 GFSK 1 Radiated Emission Test (Below 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 19 GFSK 1 Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 19 GFSK 1 Antenna Port Conducted Measurement: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Available Channel Tested Channel Modulation Type Data Rate (Mbps) Mode - 0 to 39 0, 19, 39 GFSK 1 Report No.: RF151207C04A-1 Page No. 8 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

Test Condition: Applicable To Environmental Conditions Input Power Tested by RE1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Jisyong Wang RE<1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Thomas Wei PLC 25 deg. C, 65 % RH 120 Vac, 60 Hz Jisyong Wang APCM 25 deg. C, 65 % RH 5 Vdc Gavin Wu 3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. No. Product Brand Model No. Serial No. FCC ID 1. NB & Tablet Getac V110 N/A N/A 2. Earphone N/A N/A N/A N/A No. Signal Cable Description Of The Above Support Units 1. N/A 2. N/A Note: 1. All power cords of the above support units are non-shielded (1.8m). 3.3.1 Configuration of System under Test EUT NB & Tablet Earphone *Test Table (Power from host equipment) 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.247) KDB 558074 D01 15.247 Meas Guidance v05 ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Report No.: RF151207C04A-1 Page No. 9 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20 dB below the highest level of the desired power: Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F (kHz) 300 0.490 ~ 1.705 24000/F (kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 Note: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000 MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20 dB under any condition of modulation. Report No.: RF151207C04A-1 Page No. 10 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4.1.2 Test Instruments Description & Due Date of Model No. Serial No. Date of Calibration Manufacturer Calibration Test Receiver N9038A MY51210203 Mar. 16, 2018 Mar. 15, 2019 Agilent Spectrum Analyzer N9010A MY52220314 Nov. 24, 2017 Nov. 23, 2018 Agilent Spectrum Analyzer FSU43 101261 Jan. 11, 2018 Jan. 10, 2019 ROHDE & SCHWARZ HORN Antenna BBHA 9120D 9120D-969 Nov. 12, 2017 Nov. 11, 2018 SCHWARZBECK HORN Antenna BBHA 9170 148 Dec. 13, 2017 Dec. 12, 2018 SCHWARZBECK BILOG Antenna VULB 9168 9168-472 Dec. 06, 2017 Dec. 05, 2018 SCHWARZBECK Loop Antenna EM-6879 269 Sep. 07, 2018 Sep. 06, 2019 Preamplifier EMC001340 980201 Nov. 01, 2017 Oct. 30, 2018 EMCI Preamplifier EMC 012645 980115 Oct. 20, 2017 Oct. 19, 2018 EMCI Preamplifier EMC 330H 980112 Oct. 13, 2017 Oct. 12, 2018 EMCI Power Meter ML2495A 1012010 Sep. 05, 2018 Sep. 04, 2019 Anritsu Power Sensor MA2411B 1315050 Sep. 04, 2018 Sep. 03, 2019 Anritsu RF Coaxial Cable EMC104-SM-SM-8 140811+170717 Oct. 20, 2017 Oct. 19, 2018 HUBER+SUHNNER 000&3000 RF Coaxial Cable EMC104-SM-SM- SUCOFLEX 104 Oct. 20, 2017 Oct. 19, 2018 HUBER+SUHNNER 1000(140807) RF Coaxial Cable 8D-FB Cable-Ch10-01 Oct. 20, 2017 Oct. 19, 2018 Worken Boresight Antenna Fixture FBA-01 FBA-SIP01 NA NA Software E3 NA NA NA BV ADT 6.120103 Antenna Tower MFA-440H NA NA NA MF Turn Table MFT-201SS NA NA NA MF Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 10. 3. The horn antenna and preamplifier (model: EMC 184045) are used only for the measurement of emission frequency above 1GHz if tested. 4. The IC Site Registration No. is IC7450F-10. Report No.: RF151207C04A-1 Page No. 11 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4.1.3 Test Procedures For Radiated Emission below 30 MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Parallel, perpendicular, and ground-parallel orientations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9 kHz at frequency below 30 MHz. For Radiated Emission above 30 MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for 30 MHz ~ 1 GHz) / 1.5 meters (for above 1 GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detected function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz for Quasi-peak detection (QP) at frequency below 1 GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1 GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98 %) or 10 Hz (Duty cycle ≥ 98 %) for Average detection (AV) at frequency above 1 GHz. (RBW = 1 MHz, VBW = 3 kHz) 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF151207C04A-1 Page No. 12 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4.1.5 Test Set Up <Radiated Emission below 30 MHz> 1m EUT& 3m Support Units Turn Table 80 cm Ground Plane Test Receiver <Radiated Emission 30 MHz to 1 GHz> Ant. Tower 1-4m Variable EUT& 3m 10m Support Units Turn Table 80cm Ground Plane Test Receiver Report No.: RF151207C04A-1 Page No. 13 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

<Radiated Emission above 1 GHz> Ant. Tower 1-4 m Variable EUT& 3m Support Units Turn Table Absorber 150 cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF151207C04A-1 Page No. 14 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4.1.7 Test Results Above 1 GHz Data: EUT Test Condition Measurement Detail Channel Channel 0 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Jisyong Wang Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2358.72 37.49 43.65 54 -16.51 27.01 4.32 37.49 174 339 Average 2358.72 47.82 53.98 74 -26.18 27.01 4.32 37.49 174 339 Peak 2402 96.05 102.04 27.16 4.37 37.52 174 339 Average 2402 101.46 107.45 27.16 4.37 37.52 174 339 Peak 4804 40.26 55.23 54 -13.74 31.14 6.79 52.9 152 111 Average 4804 45.19 60.16 74 -28.81 31.14 6.79 52.9 152 111 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2325.4 46.47 52.8 54 -7.53 26.85 4.29 37.47 163 32 Average 2325.4 52.09 58.42 74 -21.91 26.85 4.29 37.47 163 32 Peak 2402 98.76 104.75 27.16 4.37 37.52 163 32 Average 2402 104.43 110.42 27.16 4.37 37.52 163 32 Peak 4804 39.26 54.23 54 -14.74 31.14 6.79 52.9 265 231 Average 4804 44.94 59.91 74 -29.06 31.14 6.79 52.9 265 231 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. 2402 MHz: Fundamental frequency. 3. The emission levels of other frequencies were very low against the limit. Report No.: RF151207C04A-1 Page No. 15 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

EUT Test Condition Measurement Detail Channel Channel 19 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Jisyong Wang Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2363.62 46.11 52.26 54 -7.89 27.01 4.33 37.49 172 331 Average 2363.62 51.74 57.89 74 -22.26 27.01 4.33 37.49 172 331 Peak 2440 98.03 103.71 27.38 4.4 37.46 172 331 Average 2440 103.38 109.06 27.38 4.4 37.46 172 331 Peak 2485.64 35.65 41.01 54 -18.35 27.53 4.43 37.32 172 331 Average 2485.64 48.5 53.86 74 -25.5 27.53 4.43 37.32 172 331 Peak 4880 40.65 55.4 54 -13.35 31.25 6.86 52.86 152 231 Average 4880 45.73 60.48 74 -28.27 31.25 6.86 52.86 152 231 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2363.06 50.9 57.05 54 -3.1 27.01 4.33 37.49 164 29 Average 2363.06 55.22 61.37 74 -18.78 27.01 4.33 37.49 164 29 Peak 2440 99.01 104.69 27.38 4.4 37.46 164 29 Average 2440 104.01 109.69 27.38 4.4 37.46 164 29 Peak 2498.44 35.59 40.79 54 -18.41 27.61 4.44 37.25 164 29 Average 2498.44 48.47 53.67 74 -25.53 27.61 4.44 37.25 164 29 Peak 4880 39.5 54.25 54 -14.5 31.25 6.86 52.86 265 231 Average 4880 44.38 59.13 74 -29.62 31.25 6.86 52.86 265 231 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. 2440 MHz: Fundamental frequency. 3. The emission levels of other frequencies were very low against the limit. Report No.: RF151207C04A-1 Page No. 16 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

EUT Test Condition Measurement Detail Channel Channel 39 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Jisyong Wang Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2480 99.27 104.63 27.53 4.43 37.32 172 330 Average 2480 104.31 109.67 27.53 4.43 37.32 172 330 Peak 2484.08 39.84 45.2 54 -14.16 27.53 4.43 37.32 172 330 Average 2484.08 58.42 63.78 74 -15.58 27.53 4.43 37.32 172 330 Peak 4960 40.17 54.79 54 -13.83 31.4 6.9 52.92 152 231 Average 4960 45.28 59.9 74 -28.72 31.4 6.9 52.92 152 231 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2480 97.61 102.97 27.53 4.43 37.32 160 29 Average 2480 102.64 108 27.53 4.43 37.32 160 29 Peak 2483.52 38.75 44.11 54 -15.25 27.53 4.43 37.32 160 29 Average 2483.52 55.81 61.17 74 -18.19 27.53 4.43 37.32 160 29 Peak 4960 40.77 55.39 54 -13.23 31.4 6.9 52.92 102 265 Average 4960 46.28 60.9 74 -27.72 31.4 6.9 52.92 102 265 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. 2480 MHz: Fundamental frequency. 3. The emission levels of other frequencies were very low against the limit. Report No.: RF151207C04A-1 Page No. 17 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

9 kHz ~ 30 MHz Data: The amplitude of spurious emissions attenuated more than 20 dB below the permissible value is not required to be report. 30 MHz ~ 1 GHz Worst-Case Data: EUT Test Condition Measurement Detail Channel Channel 19 Frequency Range 30 MHz ~ 1 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function QP (Quasi-Peak) Environmental 25 deg. C, 65 % RH Tested By Thomas Wei Conditions Horizontal Vertical Report No.: RF151207C04A-1 Page No. 18 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 43.58 28.26 45.28 40 -11.74 13.59 0.5 31.11 123 319 Peak 117.3 22.54 42.85 43.5 -20.96 10.74 0.83 31.88 148 284 Peak 190.05 28.99 49.44 43.5 -14.51 10.05 1.17 31.67 191 213 Peak 355.92 34.96 50.69 46 -11.04 14.29 1.9 31.92 234 169 Peak 492.69 28.25 40.34 46 -17.75 17.18 2.46 31.73 268 104 Peak 862.26 28.55 33.54 46 -17.45 23.03 3.9 31.92 297 55 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 43.58 28.83 45.85 40 -11.17 13.59 0.5 31.11 288 103 Peak 83.35 28.85 51.64 40 -11.15 8.18 0.68 31.65 254 166 Peak 120.21 27.01 47.05 43.5 -16.49 11.02 0.84 31.9 237 188 Peak 189.08 25.26 45.66 43.5 -18.24 10.12 1.17 31.69 192 230 Peak 358.83 32.89 48.57 46 -13.11 14.36 1.92 31.96 255 264 Peak 648.86 24.86 33.58 46 -21.14 20.2 3.11 32.03 299 321 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value 2. The emission levels of other frequencies were very low against the limit. Report No.: RF151207C04A-1 Page No. 19 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-Peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 4.2.2 Test Instruments Description & Date of Due Date of Model No. Serial No. Manufacturer Calibration Calibration Test Receiver ESCI 100613 Nov. 23, 2017 Nov. 22, 2018 ROHDE & SCHWARZ RF signal cable 5D-FB Cable-cond1-01 Sep. 05, 2018 Sep. 04, 2019 Woken LISN/AMN ROHDE & SCHWARZ ENV216 101826 Feb. 26, 2018 Feb. 25, 2019 (EUT) LISN/AMN ROHDE & SCHWARZ ESH3-Z5 100311 Aug. 19, 2018 Aug. 18, 2019 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.4 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. 4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/50 uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under (Limit – 20 dB) was not recorded. Note: The resolution bandwidth and video bandwidth of test receiver is 9 kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15 MHz - 30 MHz. Report No.: RF151207C04A-1 Page No. 20 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 4.2.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF151207C04A-1 Page No. 21 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4.2.7 Test Results CONDUCTED WORST-CASE DATA Detector Function & Quasi-Peak (QP) / Frequency Range 150kHz ~ 30MHz Resolution Average (AV), 9kHz Bandwidth Environmental Input Power 120Vac, 60Hz 25℃, 65%RH Conditions Tested by Jisyong Wang Test Date 2018/10/1 Phase Of Power : Line (L) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.19305 9.67 32.20 15.66 41.87 25.33 63.90 53.90 -22.03 -28.57 2 0.25932 9.67 28.78 10.87 38.45 20.54 61.45 51.45 -23.00 -30.91 3 0.31849 9.66 20.87 5.88 30.53 15.54 59.75 49.75 -29.22 -34.21 4 0.38851 9.66 24.36 5.15 34.02 14.81 58.10 48.10 -24.08 -33.29 5 1.22916 9.66 24.65 5.13 34.31 14.79 56.00 46.00 -21.69 -31.21 6 10.86340 9.86 13.85 1.70 23.71 11.56 60.00 50.00 -36.29 -38.44 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF151207C04A-1 Page No. 22 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

Detector Function & Quasi-Peak (QP) / Frequency Range 150kHz ~ 30MHz Resolution Average (AV), 9kHz Bandwidth Environmental Input Power 120Vac, 60Hz 25℃, 65%RH Conditions Tested by Jisyong Wang Test Date 2018/10/1 Phase Of Power : Neutral (N) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.19255 9.67 31.91 15.30 41.58 24.97 63.93 53.93 -22.35 -28.96 2 0.25864 9.67 24.31 10.89 33.98 20.56 61.47 51.47 -27.49 -30.91 3 0.31031 9.67 21.95 2.76 31.62 12.43 59.96 49.96 -28.34 -37.53 4 0.38851 9.67 25.10 4.04 34.77 13.71 58.10 48.10 -23.33 -34.39 5 0.83765 9.66 22.56 7.44 32.22 17.10 56.00 46.00 -23.78 -28.90 6 1.22916 9.66 22.36 8.27 32.02 17.93 56.00 46.00 -23.98 -28.07 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF151207C04A-1 Page No. 23 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

4.3 Conducted Output Power Measurement 4.3.1 Limits of Conducted Output Power Measurement For systems using digital modulation in the 2400–2483.5 MHz bands: 1 Watt (30 dBm) 4.3.2 Test Setup EUT Power Sensor Power Meter Attenuator 4.3.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.4 Test Procedures A peak power sensor was used on the output port of the EUT. A power meter was used to read the response of the peak power sensor. Record the power level. 4.3.5 Deviation from Test Standard No deviation. 4.3.6 EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. 4.3.7 Test Results Frequency Peak Power Peak Power Limit Channel Pass / Fail (MHz) (mW) (dBm) (dBm) 0 2402 9.183 9.63 30 Pass 19 2440 8.851 9.47 30 Pass 39 2480 8.091 9.08 30 Pass Report No.: RF151207C04A-1 Page No. 24 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF151207C04A-1 Page No. 25 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF151207C04A-1 Page No. 26 / 26 Report Format Version: 6.1.1 Reference No.: 180907C10


Document Created: 2019-04-07 15:47:17
Document Modified: 2019-04-07 15:47:17
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC