RF Exposure Evaluation

FCC ID: QWY-WMI2W167

RF Exposure Info

Download: PDF
FCCID_3934260

TEST REPORT No.: 18-1-0081001T22a-C1 According to: FCC Regulations §1.1310 § 2.1091 & 2.1093 for peiker acustic GmbH Wireless Mobile Interface WMI2-W167-M3 2609-090-554-51 Laboratory Accreditation and Listings Voluntary Controls for Electromagnetic Industry Canada Emissions Reg. No.: 3462D-1 Reg. No.: 3462D-2 Reg. No.: Accredited EMC-Test Laboratory Reg. No.: 3462D-3 R-4452, C-20009, T-20006, G-20013 MRA US-EU 0003 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 24 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 18-1-0081001T22a-C1, Page 2 of 24 Table of contents 1. Summary of test results 3 2. Administrative Data 4 2.1. Identification of the testing laboratory 4 2.2. Test location 4 2.3. Organizational items 4 2.4. Applicant’s details 4 2.5. Manufacturer’s details 4 3. Equipment under test (EUT) 5 3.1. TECHNICAL DATA OF MAIN EUT DECLARED BY APPLICANT 5 3.2. EUT: Type, S/N etc. and short descriptions used in this test report 5 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions 5 3.4. EUT set-ups 6 3.5. EUT operating modes 6 3.6. Additional declaration and description of EUT 6 4. DESCRIPTION OF TEST SET-UP’s 7 4.1. Test Set-up for configuration 7 The RF exposure test is performed in shielded room. 7 5. Maximum Permissible RF Exposure 8 5.1. FCC References & Limits 8 5.2. E-Field Results 9 5.3. H-Field Results 13 6. Measurement uncertainties 18 7. Accreditation details of CETECOM’s laboratories and test sites 18 8. Instruments and Ancillary 19 8.1. Used equipment “CTC” 19 9. Versions of test reports (change history) 24 Table of annex Total pages Annex 1: Measurement diagrams (separate document) TR18_1_0081001T22a_C1_A1 23 Annex 2: External photographs of EUT (separate document) TR18_1_0081001T22a_C1_A2 5 Annex 3: Test setup photographs (separate document) TR18_1_0081001T22a_C1_A3 8 The listed attachments are an integral part of this report. CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 3 of 24 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. The Equipment Under Test (in this report, hereinafter referred as EUT) is a wireless Mobile Interfacee with NFC. The wireless charger is operated at Frequency 125kHz. TEST OVERVIEW No. of References, Standards & Limits EUT Test EUT op- Measured Diagram Port set- Result Cases FCC Limits mode values group up 5cm §1.1310 all values are Electric field below the 1.1 distance to §2.1091 614 (V/m) 1 1+2+3 passed strength regulatory EUT §2.1093 limits 15cm §1.1310 all values are Electric field below the 1.1 distance to §2.1091 614 (V/m) 1 1+2+3 passed strength regulatory EUT §2.1093 limits 5cm §1.1310 all values are Magnetic field below the 1.2 distance to §2.1091 1.63 (A/m) 1 1+2+3 passed strength regulatory EUT §2.1093 limits all values are 15/20cm §1.1310 more than Magnetic field 1.2 distance to §2.1091 1.63 (A/m) 1 1+2+3 50% below passed strength the regulatory EUT §2.1093 limits Remark: Following tests have been performed to show compliance with applicable Standards: FCC §1.1310, §2.1091 §2.1093 OET Bulletin 65 Supplement C KDB 680106 D01 V03. Additional to KDB 680106 D01 V03 tests were performed due to customer declaration with 5cm distance between edge and top of EUT and probe. The current version of CETECOM Test Report 18-1-0081001T22a-C1 replaces the Test Report CETECOM 18-1-00810T22a dated 2018-06-13. The replaced Test Report is herewith invalid ...................................................... .................................................... Dipl.-Ing. Rachid Acharkaoui W. Markus Responsible for test section Responsible for test report CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 4 of 24 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. Rachid Acharkaoui Deputy: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report : W. Markus Receipt of EUT: 2018-06-08 Date(s) of test: 2018-06-12 Date of report: 2018-07-16 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 12.11 2.4. Applicant’s details Applicant’s name: peiker acustic GmbH Address: Max-Planck-Str. 28-32 61381 Friedrichsdorf Germany Contact person: Mr. Uwe Hännig 2.5. Manufacturer’s details Manufacturer’s name: please see Applicant's details Address: please see Applicant's details CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 5 of 24 3. Equipment under test (EUT) 3.1. TECHNICAL DATA OF MAIN EUT DECLARED BY APPLICANT Main function WMI – Wireless Mobile Interface Type W205 Frequency range Fixed frequency 125kHz for wireless charging, 13,56MHz for NFC Max. nominal power 9,25W each Coil PCB antenna - R = 4.0 Ohm Antenna Type - jZ= 58 Ohm - L = 0.68uH Power supply  12V DC Special EMI components -- EUT sample type  Production  Pre-Production  Engineering FCC label attached  yes  no 3.2. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial number hardware status software status tion*) Wireless Mobile WMI2-W167-M3 0000 E005.5 EUT A P18001040749 Interface 2609-090-554-51 17/40.01 17/40.01 *) EUT short description is used to simplify the identification of the EUT in this test report. 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE S/N HW SW short Auxiliary Equipment Type serial number hardware status software status descrip- tion *) AE 1 Main Harness -- -- -- -- VScom USB-CAN AE 2 USB-CAN Plus 380101643 -- -- Adapter AE 3 USB cable -- -- -- -- AVID Qi Receiver AE 4 102-01 00000337 -- -- Simulator 430 OHM, AE 5 OSRAM PointLED LA P47F-AABA -- -- 550mW *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 6 of 24 3.4. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) EUT A + AE 1 + AE 2 + AE 3 + AE 4 + Set. 1 for wireless charging AE 5 *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. 3.5. EUT operating modes EUT Description of operating Additional information operating modes mode no.*) Wireless charging was activated with special customer SW. op. 1 Wireless charging The EUT is transferring power to AE4 With 900mA LOAD (90% charging level) Wireless charging was activated with special customer SW. op. 2 Wireless charging The EUT is transferring power to AE4 with 500mA LOAD (50%charging level) Wireless charging was activated with special customer SW. op. 3 Wireless charging The EUT is transferring power to AE4 with 50 mA LOAD (5% charging level) *) EUT operating mode no. is used to simplify the test report. Less than 5% charging level is not possible due to technical reasons with the Qi Receiver Simulator 3.6. Additional declaration and description of EUT  table-top typical use  floor-standing  portable use Set up 1  wall-mounted  fixed use  not defined  vehicular use  Residential, commercial and light industry Place of use  Industrial environment  vehicular use typical operating cycle of EUT  < 0,5 sec.  : Power line: EUT-grounding:  AC  120V,  230V,  400V  none  PE,  N,  L1,  L2  L3  with power supply  __ Hz  additional:  DC  12.0V  24V (in case of deviation during tests the single details are described on chapter 4) Other Ports (description of interconnecting cables) connected possible total cable length shielding during test Description Connector  < 3m > 3m  screened  yes 1. Main Multi pin  : other  unscreened  no Does EUT contain devices susceptible to magnetic fields, e.g. Hall elements, electrodynamics  yes microphones, etc.?  no  yes Is mounting position / usual operating position defined?  no CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 7 of 24 4. DESCRIPTION OF TEST SET-UP’s 4.1. Test Set-up for configuration The RF exposure test is performed in shielded room. The EUT was placed on a table. The measurement probe was surrounding point 1 to point 4 at a distance of 5cm and 15cm from the EUT and 5cm and 20 cm above the top surface (point 5) for H-filed strength The measurement probe was surrounding point 1 to point 4 at a distance of 5cm and 15cm from the EUT and 5cm and 15cm above the top surface (point 5) for E-filed strength RF- Probe Field Probe be 5 / 15 / 20cm 5 / 15cm 5 / 15cm be Probe Field RF- e Probe Field RF- EUT 5 /15 cm 5 / 15cm Schematic: Test set-up for Rf exposure measurements CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 8 of 24 5. Maximum Permissible RF Exposure 5.1.FCC References & Limits FCC Rules: §1.1310, § 2.1093 The criteria used for the evaluation of human exposure to radio frequency radiation is listed in table 1 according FCC §1.1307(b, except in the case of portable devices which shall be evaluated according to the provisions of §2.1093 of this. Note 1 to table 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provide those persons are fully aware for a exposure and can control over their exposure. Limits for occupational/controlled exposures also apply in situations when an individual is transient through a location where occupational/controlled apply provided he or she is made aware of the potential for exposure. Note 2 to table 1: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. So applicable limits in this case are as follows: §1.1310 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Table 1(B) Limits for General Population/Uncontrolled Exposure 0.3–1,34 MHz: Electric field: 614 V/m 0.3–1,34 MHz: Magnetic field: 1.63 A/m CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 9 of 24 5.2. E-Field Results 5.2.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter 2.2.1)  Please see Chapter 2.2.2  Please see Chapter 2.2.3 equipment  686 EHP-200A      signaling  017 CMD 65  323 CMD 55  340 CMD 55 signaling  298 CMU  460 CMU  295 RACAL  392 MT8820A line voltage  12V DC 5.2.2. Test condition and test set-up link to test system (if used):  air link  cable connection EUT-grounding (if different to chapter 3.5)  none  with power supply  additional connection Equipment set up - - Climatic conditions Temperature: 24 °C Rel. humidity: 31 % 5.2.3. Results Table 1: The aggregate E-Field strenghts at 15cm surrounding the device: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 1 (90% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 1 0.15 0,84 614 125 2 0.15 1,21 614 125 3 0.15 1,0 614 125 4 0.15 0,86 614 Remarks: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 2 (50% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 1 0.15 0,54 614 125 2 0.15 0,89 614 125 3 0.15 0,65 614 125 4 0.15 0,59 614 Remarks: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 3 (5% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 1 0.15 0,43 614 125 2 0.15 0,42 614 125 3 0.15 0,33 614 125 4 0.15 0,35 614 Remarks: CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 10 of 24 Table 2: The aggregate E-Field strenghts at 15cm above the top of the device: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 1 (5% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 5 0.15 6,94 614 Remarks: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 2 (50% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 5 0.15 4,57 614 Remarks: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 3 (90% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 5 0.15 1,33 614 Remarks: CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 11 of 24 Table 3: The aggregate E-Field strenghts at 5cm surrounding the device: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 1 (90% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 1 0.05 1,87 614 125 2 0.05 2,51 614 125 3 0.05 1,99 614 125 4 0.05 1,69 614 Remarks: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 2 (50% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 1 0.05 1,4 614 125 2 0.05 1,82 614 125 3 0.05 1,11 614 125 4 0.05 1,19 614 Remarks: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 3 (5% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 1 0.05 1,05 614 125 2 0.05 1,07 614 125 3 0.05 0,53 614 125 4 0.05 0,70 614 Remarks: CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 12 of 24 Table 4: The aggregate E-Field strenghts at 5cm above the top of the device: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 1 (5% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 5 0.05 12,5 614 Remarks: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 1 (5% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 5 0.05 8,76 614 Remarks: EUT Type and S/N or EUT set-up no. Set- up 1 EUT operating mode or EUT operating mode 1 (5% charging level) operating mode no. Frequency Distance between E-field E-field Position Range EUT and Field (V/m) Limit probe (V/m) (kHz) (m) 125 5 0.05 3,93 614 Remarks: CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 13 of 24 5.3. H-Field Results 5.3.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter 2.2.1)  Please see Chapter 2.2.2  Please see Chapter 2.2.3 equipment  686 EHP-200A      signaling  017 CMD 65  323 CMD 55  340 CMD 55 signaling  298 CMU  460 CMU  295 RACAL  392 MT8820A line voltage  12V DC 5.3.2. Test condition and test set-up link to test system (if used):  air link  cable connection EUT-grounding (if different to chapter 3.5)  none  with power supply  additional connection Equipment set up - - Climatic conditions Temperature: 24 °C Rel. humidity: 31 % Table 5: The aggregate H-Field strenghts at 15cm surrounding the device: EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 1 (90% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 1 0.15 0,21 1.63 0,815 passed 125 2 0.15 0,25 1.63 0,815 passed 125 3 0.15 0,16 1.63 0,815 passed 125 4 0.15 0,16 1.63 0,815 passed 125 5 0.15 0,45 1.63 -- passed Remarks: 1) according KDB 680106 D01 V03 EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 2 (50% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 1 0.15 0,17 1.63 0,815 passed 125 2 0.15 0,16 1.63 0,815 passed 125 3 0.15 0,10 1.63 0,815 passed 125 4 0.15 0,11 1.63 0,815 passed 125 5 0.15 0,65 1.63 -- passed Remarks: 1) according KDB 680106 D01 V03 CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 14 of 24 EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 3 (5% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 1 0.15 0,12 1.63 0,815 passed 125 2 0.15 0,11 1.63 0,815 passed 125 3 0.15 0,06 1.63 0,815 passed 125 4 0.15 0,09 1.63 0,815 passed 125 5 0.15 0,95 1.63 -- passed Remarks: 1) according KDB 680106 D01 V03 CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 15 of 24 Table 6: The aggregate H-Field strenghts at 20cm above the top of the device: EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 1 (90% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 5 0.2 0,54 1.63 0,815 passed 1 Remarks: ) according KDB 680106 D01 V03 EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 2 (50% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 5 0.2 0,43 1.63 0,815 passed Remarks: 1) according KDB 680106 D01 V03 EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 3 (5% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 5 0.2 0,29 1.63 0,815 passed Remarks: 1) according KDB 680106 D01 V03 CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 16 of 24 Table 7: The aggregate H-Field strenghts at 5cm surrounding the device: EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 1 (90% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 1 0.05 0,36 1.63 0,815 passed 125 2 0.05 0,40 1.63 0,815 passed 125 3 0.05 0,25 1.63 0,815 passed 125 4 0.05 0,25 1.63 0,815 passed Remarks: 1) according KDB 680106 D01 V03 EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 2 (50% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 1 0.05 0,17 1.63 0,815 passed 125 2 0.05 0,21 1.63 0,815 passed 125 3 0.05 0,24 1.63 0,815 passed 125 4 0.05 0,25 1.63 0,815 passed Remarks: 1) according KDB 680106 D01 V03 EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 3 (5% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 1 0.05 0,15 1.63 0,815 passed 125 2 0.05 0,17 1.63 0,815 passed 125 3 0.05 0,18 1.63 0,815 passed 125 4 0.05 0,21 1.63 0,815 passed Remarks: 1) according KDB 680106 D01 V03 CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 17 of 24 Table 8: The aggregate H-Field strenghts at 5cm above the top of the device: EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 1 (90% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 5 0.05 1,30 1.63 0,815 passed 1 Remarks: ) according KDB 680106 D01 V03 EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 2 (50% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 5 0.05 0,43 1.63 0,815 passed Remarks: 1) according KDB 680106 D01 V03 EUT Type and S/N or EUT set- Set-up 1 up no. EUT operating mode or EUT operating mode 3 (5% charging level) operating mode no. Frequency Distance Range between H-field H-field Position EUT and H-field Limit Limit – 50% Result Field (A/m) (kHz) (A/m) (A/m) 1) probe (m) 125 5 0.05 0,29 1.63 0,815 passed Remarks: 1) according KDB 680106 D01 V03 CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 18 of 24 6. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it’s contribution to the overall uncertainty according it’s statistical distribution calculated. Following table shows expectable uncertainties for each measurement type performed. Calculated uncertainty based RF-Measurement Frequency range Remarks: on a confidence level of 95% Power Output conducted 9 kHz .. 20 GHz 1.0 dB -- Power Output radiated 30 MHz .. 4 GHz 3.17 dB Substitution method Conducted emissions on antenna ports 9 kHz .. 20 GHz 1.0 dB -- 9 kHz .. 30 MHz 5.0 dB Magnetic field 9 MHz .. 1 GHz 5.0 dB E-Field Radiated emissions enclosure 30 MHz .. 1 GHz 4.2 dB E-Field 1 GHz .. 20 GHz 3.17 dB Substitution method 9 kHz .. 4 GHz 0.1272 ppm (Delta Marker ) Frequency error Occupied bandwidth 1.0 dB Power 9 kHz .. 4 GHz 0.1272 ppm (Delta Marker) Frequency error Emission bandwidth 1.0 dB Power Frequency stability 9 kHz .. 20 GHz 0.0636 ppm -- Conducted emissions 9 kHz .. 150 kHz 4.0 dB -- on AC-mains port (UCISPR) 150 kHz .. 30 MHz 3.6 dB Table: measurement uncertainties, valid for conducted/radiated measurements 7. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS, Deutsche All laboratories and test sites of CETECOM GmbH, Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) FCC, Federal Communications 487 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) MRA US-EU Commission 558 Radiated Measurements above 1 GHz, 3 m (FAR) 0003 Laboratory Division, USA 348 Mains Ports Conducted Interference Measurements (MRA US-EU 0003) 348 Telecommunication Ports Conducted Interference Measurem. 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) IC, Industry Canada 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) Certification and Engineering 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) Bureau 558 3462D-3 Radiated Measurements above 1 GHz, 3 m (FAR) 337 R-20013 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) VCCI, Voluntary Control 487 G-20013 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) Council for Interference by 550 C-20009 Mains Ports Conducted Interference Measurements Information Technology 348 T-20006 Telecommunication Ports Conducted Interference Measurem. Equipment, Japan OATS = Open Area Test Site, SAR = Semi Anechoic Room, FAR = Fully Anechoic Room CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 19 of 24 8. Instruments and Ancillary 8.1. Used equipment “CTC” The “Ref.-No” in the left column of the following tables allows the clear identification of the laboratory equipment. 8.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 EMI Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 264 Spectrum Analyzer FSEK 30 826939/005 Bios=2.1, Analyzer= 3.20 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 TSI 1.53 335 CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.52 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band 441 CTC-SAR-EMI Cable Loss System EMI field (SAR) - EMC 32 Version 8.52 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 9.15.00 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 9.15.00 R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 620 EMI Test Receiver ESU 26 100362 4.43_SP3 642 Wideband Radio Communication Tester CMW 500 126089 Setup V03.26, Test programm component V03.02.20 CBT V 5.40, FW: V.2.41 (FPGA Digital, V. 3.09 FPGA 692 Bluetooth Tester CBT 32 100236 RF) CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 20 of 24 8.1.2. Single instruments and test systems Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 EMI Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 264 Spectrum Analyzer FSEK 30 826939/005 Bios=2.1, Analyzer= 3.20 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 TSI 1.53 335 CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.52 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 383 Signal Generator SME 03 842 828 /034 Firm.= 4.61 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band 441 CTC-SAR-EMI Cable Loss System EMI field (SAR) - EMC 32 Version 8.52 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 8.53 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 8.40 R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 620 EMI Test Receiver ESU 26 100362 4.43_SP3 642 Wideband Radio Communication Tester CMW 500 126089 Setup V03.26, Test programm component V03.02.20 CBT V 5.40, FW: V.2.41 (FPGA Digital, V. 3.09 FPGA 692 Bluetooth Tester CBT 32 100236 RF) CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 21 of 24 8.1.3. Single instruments and test systems Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 001 EMI Test Receiver ESS 825132/017 Rohde & Schwarz 12 M - 16.05.2019 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 12 M - 16.05.2019 007 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 12 M - 16.05.2019 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 15.05.2019 011 Insertion Unit (EMS-radiated) URV5-Z2 864169/004 Rohde & Schwarz 24 M - 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Rohde & Schwarz 24 M - 15.05.2019 013 Power Meter (EMS cond.) NRVD 839111/003 Rohde & Schwarz 24 M - 15.05.2019 014 Insertion Unit (EMS cond.) URV5-Z2 838519/029 Rohde & Schwarz 24 M - 15.05.2019 015 Insertion Unit (EMS cond.) URV5-Z4 838570/024 Rohde & Schwarz 24 M - 15.05.2019 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 30.05.2019 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Rohde & Schwarz pre-m 3 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 30.05.2021 031 Absorbing Clamp MDS-21 863325/015 Rohde & Schwarz 36 M - 30.05.2021 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 15.05.2019 049 Current Clamp (injection) F-120-2 48 FCC 24 M - 30.05.2020 050 3-ph Coupling Decoupling Netw. (Burst) CDN 300 176 Schaffner 36 M - 30.05.2021 051 VHF-Current Probe 20-300 MHz ESV-Z1 872421 Rohde & Schwarz 36 M - 30.05.2021 052 Notch Filter DECT WRCB 1887,82/1889,55SS 12 Wainwright Industries pre-m 2 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 058 capacitive clamp (Burst) IP 4 99 Haefely 36 M - 30.05.2021 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 067 coupling decoupling-network CDN 801-M2/M3 272 Lüthi 36 M - 15.05.2020 068 coupling decoupling-network CDN 801-M5 95226 Lüthi 36 M - 17.05.2020 069 EM - clamp EM101 9535159 Lüthi 36 M - 30.05.2019 072 coupling decoupling-network CDN 801-M2/M3 276 Lüthi 36 M - 17.05.2020 083 AC - power supply, 0-10 A EAC/MT 27010 910502096 EURO TEST pre-m 2 084 AC - power supply, 0-5 A ELABO-8-34214 - ELABO pre-m 2 085 AC - power supply, 0-10 A R250 - Schunterm.&Benningh. pre-m 2 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 094 artificial head (No.1) 4905 1566990 Brüel & Kjaer pre-m 2 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 30.05.2021 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 30.05.2021 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 BOCONSULT 36 M - 30.05.2019 131 RF-Current Probe F-52 19 FCC 36 M - 17.05.2020 133 horn antenna 18 GHz (Meas 1) 3115 9012-3629 EMCO 36 M 1c 10.03.2020 134 horn antenna 18 GHz (Subst 2) 3115 9005-3414 EMCO 36 M - 10.03.2020 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24 M - 30.05.2020 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 30.05.2019 263 Signal Generator SMP 04 826190/0007 Rohde & Schwarz 36 M - 30.05.2019 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 30.05.2020 266 Peak Power Sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 30.05.2020 267 notch filter GSM 850 WRCA 800/960-6EEK 9 Wainwright GmbH pre-m 2 268 AC/DC power supply EA 3050-A 9823636 Elektro Automatik pre-m - 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 274 attenuator (10 dB) 50 W Model 47 (10 dB) 50 W BG0321 Weinschel pre-m 2 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 284 coupling decoupling network CDN 801-M1 1661 Lüthi 36 M - 17.05.2020 285 coupling decoupling network CDN 801-S1 1642 Lüthi 36 M - 17.05.2020 295 Racal Digital Radio Test Set 6103 1572 Racal pre-m 3 R=316568/004 296 audio measurement amplifier 2636C (Reserve) Brüel & Kjaer pre-m 2 B=1537541 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 299 audio microphone 134 - Brüel & Kjaer pre-m 2 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 12 M - 17.05.2019 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 22 of 24 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 14.03.2020 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 20.03.2020 304 fix dipole antenna 1,6 GHz EMCO 3125-307 9907-1001 ETS pre-m - 305 fix dipole antenna 1,8-2,0 GHz EMCO 3125-306 9907-1001 ETS pre-m - 306 fix dipole antenna 2,45 GHz EMCO 3125-308 9907-1001 ETS pre-m - 307 fix dipole antenna 3 GHz EMCO 3125-309 9907-1001 ETS pre-m - 317 1000 Hz calibrator 94 dB SPL 4230 94dB 1542286 Brüel & Kjaer 12 M - 323 Digital Radiocommunication Tester CMD 55 825878/0034 Rohde & Schwarz pre-m 3 337 System CTC OATS NSA System EMI OATS NSA - HD GmbH 24 M 5 12.04.2019 340 Digital Radiocommunication Tester CMD 55 849709/037 Rohde & Schwarz pre-m 3 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 30.05.2020 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 17.05.2019 344 adaptor 150/50 Ohm 150/50 - Krohne 36 M - 17.05.2020 345 adaptor 150/50 Ohm 150/50 - Krohne 36 M - 17.05.2020 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 349 car battery 12 V car battery 12 V without - - 3 350 car battery 12 V car battery 12 V without - - 3 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 24.05.2019 363 Kalibrieradapter HF-uns. CR 100 A without Lüthi 24 M - 30.05.2020 364 Kalibrieradapter HF-uns. CR 100 A 128 Lüthi 24 M - 30.05.2020 366 Ultra Compact Simulator UCS 500 M4 V0531100594 EM-Test 12 M - 30.05.2019 368 ROD-Antenna HFH 2-Z1 879283/31 Rohde & Schwarz 60 M - 17.07.2019 371 Bluetooth Tester CBT32 100153 R&S 36 M - 30.05.2019 373 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 100535 Rohde & Schwarz 12 M - 17.05.2019 374 Power Amplifier 0,8-3 GHz 60S1G3 306528 Amplifier Research 12 M 1a 20.03.2018 375 Directional Coupler DC7144M1 306498 Amplifier Research 12 M 1a 20.03.2018 376 Horn Antenna 6 GHz BBHA9120 E BBHA 9120 E 179 Schwarzbeck 36 M - 28.02.2020 377 EMI Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 30.05.2019 386 Coupling Decoupling Network CDN USB/p 19397 Schaffner 36 M - 17.05.2020 387 Coupling Decoupling Network CDN L-801 M2 2051 Lüthi 36 M - 18.05.2020 388 Coupling Decoupling Network CDN L-801 T2 1929 Lüthi 36 M - 18.05.2020 389 Digital Multimeter Keithley 2000 0583926 Keithley pre-m - 390 Industry Acoustic System MO 2000 Set 2127100123 Sennheiser pre-m 2 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 18.05.2018 399 Sound Calibrator Sound Calibrator 4231 2665101 Brüel & Kjaer 12 M - 30.05.2019 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 06.03.2019 439 UltraLog-Antenna HL 562 100248 Rohde & Schwarz 36 M - 10.03.2020 440 CDN for Datacable CDN-UTP CDN-UTP 029 EMC Partner AG, CH 36 M - 30.05.2019 ETS-Lindgren / 442 CTC-SAR-EMS System EMS field (SAR) - 12 M 5 20.03.2018 CETECOM 450 6dB attenuator N/N 6806.17B 6dB - Huber & Suhner 12 M - 20.05.2019 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 455 Oscilloscope HP 54602B US 350 336 45 Hawlett Packard - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 30.05.2019 462 AF-Generator MX-2020 - Conrad - 4 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 30.05.2020 467 Digital Multimeter Fluke 112 89680306 Fluke USA 36 M - 30.05.2019 468 Digital Multimeter Fluke 112 90090455 Fluke USA 36 M - 30.04.2021 477 ReRadiating GPS-System AS-47 - Automotive Cons. Fink - 3 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 16.05.2019 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d ETS Lindgren / 487 System CTC NSA-Verification SAR-EMI System EMI field (SAR) NSA - 24 M - 31.03.2019 CETECOM 489 EMI Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 18.05.2018 491 ESD Simulator dito ESD dito dito307022 EM-Test 12 M - 30.05.2019 498 Power Supply NGPE 40/40 402 Rohde & Schwarz pre-m 2 500 Industry Acoustic System MO 2000 Set 100048 Sennheiser pre-m 2 502 band reject filter WRCG 1709/1786-1699/1796- SN 9 Wainwright pre-m 2 503 band reject filter WRCG 824/849-814/859- SN 5 Wainwright pre-m 2 517 relais switch matrix HF Relais Box Keithley SE 04 Keithley pre-m 2 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 18.05.2019 524 Voltage Drop Simulator VDS 200 0196-16 EM Test 24 M - 16.05.2019 525 CDN coupling network CNA 200 1196-01 EM Test 24 M - 16.05.2019 526 Burst Generator EFT 200 A 0496-06 EM Test 24 M - 16.05.2019 527 Micro Pulse Generator MPG 200 B 0496-05 EM Test 24 M - 16.05.2019 528 Load Dump Simulator LD 200B 0496-06 EM Test 24 M - 16.05.2019 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 23 of 24 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 530 10 dB Broadband resistive power divider R 416110000 LOT 9828 - pre-m 2 533 Impedance Stabilization Network ISN T200A 25706 Teseq 36 M - 18.05.2020 534 Impedance Stabilization Network ISN T400A 24881 Teseq 36 M - 18.05.2020 535 Impedance Stabilization Network ISN T800 26321 Teseq 36 M - 18.05.2020 536 Impedance Stabilization Network ISN ST08 25867 Teseq 36 M - 18.05.2020 541 Impedance Stabilization Network ISN T8-Cat6 26373 Teseq Berlin 36 M - 18.05.2020 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 30.03.2018 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 05.07.2018 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz 36/12 M - 31.07.2018 System CTC S-VSWR Verification SAR- System EMI Field SAR S- ETS 550 - 24 M - 30.03.2019 EMI VSWR Lindgren/CETECOM 558 System CTC FAR S-VSWR System CTC FAR S-VSWR - CTC 24 M - 08.08.2019 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia 36/12 M - 31.03.2019 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz pre-m - 592 CDN-HDMI CDN-HDMI A3029004 Frankonia / Dr.Hubert 36 M - 18.05.2020 595 Analog Adder TS8910 - Rohde & Schwarz pre-m 2 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz pre-m - 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 17.05.2019 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 607 Signal Generator SMR 20 832033/011 Rohde & Schwarz 36 M - 18.05.2020 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 613 Attenuator R416120000 20dB 10W Lot. 9828 Radiall pre-m 2 615 Analog Adder TS8920 - Rohde & Schwarz pre-m 2 616 Digitalmultimeter Fluke 177 88900339 Fluke 24 M - 30.05.2020 620 EMI Test Receiver ESU 26 100362 Rohde-Schwarz 12 M - 30.05.2019 625 Generic Test Load USB Generic Test Load USB - CETECOM - 2 201.0999.9302.6.4. 627 data logger OPUS 1 G. Lufft GmbH 24 M - 30.03.2019 1.43 637 High Speed HDMI with Ethernet 1m HDMI cable with Ethernet 1m - KogiLink - 2 638 HDMI Kabel with Ethernet 1,5 m flach HDMI cable with Ethernet - Reichelt - 2 640 HDMI cable 2m rund HDMI cable 2m rund - Reichelt - 2 641 HDMI cable with Ethernet Certified HDMI cable with - PureLink - 2 642 Wideband Radio Communication Tester CMW 500 126089 Rohde&Schwarz 24 M - 24.05.2019 644 Amplifierer ZX60-2534M+ SN865701299 Mini-Circuits - - 645 Power Amplifier CBA 230M-080 T44236 TESEQ - 1g 670 Univ. Radio Communication Tester CMU 200 106833 Rohde & Schwarz 24 M - 30.05.2020 671 DC-power supply 0-5 A EA-3013S - Elektro Automatik pre-m 2 672 Digitalmultimeter Keithley 2700 1182075 Keithley pre-m - 673 Diditalmultimeter Keithley 2700 1181408 Keithley pre-m - 674 Digitalmultimeter Keithley 2700 1182090 Keithley pre-m - 675 Digitalmultimeter Keithley 2700 1162865 Keithley pre-m - 676 Digitalmultimeter Keithley 2700 1182092 Keithley 24 M - 16.05.2019 677 Digitalmultimeter Keithley 2700 1182089 Keithley pre-m - 678 Power Meter NRP 101638 Rohde&Schwarz pre-m - 679 Power Supply High Speed Power Supply 0783417 Keithley pre-m - 680 Power Sensor NRP-Z21 100622 Rohde & Schwarz pre-m - 682 Vector Signal Generator SMU 200A 101319 Rohde & Schwarz pre-m - 683 Spectrum Analyzer FSU 26 200571 Rohde & Schwarz 12 M - 30.05.2019 684 Widerstand 100 Ohm SL 403-403 72973 Teseq pre-m - 685 Widerstand 100 OHM SL 403-403 72974 Teseq pre-m - Narda Safety Test 686 Field Analyzer EHP-200A 160WX30702 24 M - 29.03.2019 Solutions 687 Signal Generator SMF 100A 102073 Rohde&Schwarz 12 M - 30.05.2019 689 Vector Signal Generator SMU200 100970 Rohde&Schwarz 24 M - 30.05.2020 690 Spectrum Analyzer FSU 100302/026 Rohde&Schwarz 24 M - 16.05.2019 692 Bluetooth Tester CBT 32 100236 Rohde & Schwarz 36 M - 29.05.2020 695 ReRadiating GPS-System AS-47 G1406003500001 Automotive Cons. Fink - 3 698 Sound Calibrator Sound Calibrator 4231 2035208 Brüel & Kjaer 12 M - 30.05.2019 700 Audio Analyzer UPL 16 830695/0016 Rohde&Schwarz 24 M - 30.04.2020 705 NRV-Z1 Power Sensor 893350/020 Rohde & Schwarz 12 M - 30.05.2019 706 NRV-Z1 Power Sensor 830961/001 Rohde &Schwarz 12 M - 30.05.2019 707 RadiCentre CTR-1004B 10I00037SN038-1 D.A.R.E!! Instruments 24 M - Laser powered Electrical Field Strength D.A.R.E.!! Instruments 708 RadiSense 6 10I00037SN038 24 M - 31.03.2019 Probe BV 710 RF Power Amplifier BLMA 2560-100 1610879 Bonn Elektronik 12 M - 20.03.2018 711 Harmonic Mixer 90 GHz - 140GHz RPG FS-Z140 101004 RPG 24 M - 22.02.2019 712 Harmonic Mixer 75 GHz - 110GHz FS-Z110 101468 Rohde & Schwarz 24 M - 22.02.2019 713 Harmonic Mixer, 50 GHz - 75GHz FS-Z75 101022 Rohde & Schwarz 24 M - 22.05.2019 714 Signal Analyzer 67GHz FSW67 104023 Rohde & Schwarz 24 M - 28.02.2020 RPG Radiometer 715 Harmonic Mixer, 140 GHz - 220GHz FS-Z220 101009 24 M - 03.08.2019 Physics 716 Harmonic Mixer 220 GHz to 325 GHZ FS-Z325 101005 RPG Radiometer Physics 24 M - 13.02.2019 CETECOM_TR18_1_0081001T22a_C1.docx

Test Report 18-1-0081001T22a-C1, Page 24 of 24 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 717 Signal Generator SMP02 830682/005 Rohde&Schwarz 36 M - 718 Robot Dasy 5 / TX90 F11/5GM9A1/A/01 Stäubli pre-m - 747 Spectrum Analyzer FSU 26 200152 Rohde & Schwarz 12 M - 30.05.2019 751 Digital Optical System optoCAN-FD Transceiver 17-010416 mk-messtechnik GmbH - - 752 Digital Optical System optoCAN-FD Transceiver 17-010083 mk-messtechnik GmbH - - 753 Digital Optical System optoCAN-FD Transceiver 17-010084 mk-messtechnik GmbH - - 754 Digital Optical System optoCAN-FD Transceiver 17-010415 mk-messtechnik GmbH - - 755 Digital Optical System optoLAN-100-MAX 17-010795 mk-messtechnik GmbH - - WIDEBAND RADIO 757 CMW500 163673 Rohde&Schwarz 12 M - 20.07.2018 COMMUNICATION 758 Signal Generator SMU 200A 100754 Rohde & Schwarz 24 M - 11.10.2019 780 Spectrum Analyzer FSH3 101726 Rohde & Schwarz 12 M - 19.07.2018 Elektro-Automatik 781 Power Supply PS 2042-10 B 2815450369 - - GmbH lektro-Automatik GmbH 782 Power Supply PS 2042-10 B 2815450348 - - &Co.KG 783 Spectrum Analyzer FSU 26 100414 Rohde & Schwarz 12 M - 30.05.2019 784 Power Supply NGSM 32/10 00196 Rohde & Schwarz 12 M - 785 RSP RF Step Attenuator 860712/012 Rohde & Schwarz 12 M - 8.1.4. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibration of this equipment Ancillary equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months, between this every 12 months internal validation 36/12 M Calibration every 36 months, between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration 9. Versions of test reports (change history) Version Applied changes Date of release -- Initial release 2018-06-13 C1 Additional test H-Field 15cm top side 2018-07-16 CETECOM_TR18_1_0081001T22a_C1.docx


Document Created: 2018-07-17 08:44:38
Document Modified: 2018-07-17 08:44:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC