test report

FCC ID: QWHULG10

Test Report

Download: PDF
FCCID_4350571

Page 1 of 33 Report No.: UNIA19041914FR-01 FCC RADIO TEST REPORT FCC ID: QWHULG10 Product： Guitar Wireless System Trade Name： Behringer Model Name： AIRPLAY GUITAR ULG10 Serial Model： N/A Report No.： UNIA19041914FR-01 Prepared for MUSIC Tribe Manufacturing PH Ltd. 17A Brunswick Street Hamilton HM 10 Bermuda, Hamilton 999078, Bermuda Prepared by Shenzhen United Testing Technology Co., Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China

Page 2 of 33 Report No.: UNIA19041914FR-01 TEST RESULT CERTIFICATION Applicant’s name ..................: MUSIC Tribe Manufacturing PH Ltd. 17A Brunswick Street Hamilton HM 10 Bermuda, Hamilton Address................................... : 999078, Bermuda Manufacture's Name.............: MUSIC Tribe Manufacturing PH Ltd. 17A Brunswick Street Hamilton HM 10 Bermuda, Hamilton Address................................... : 999078, Bermuda Product description Product name ........................... : Guitar Wireless System Trade Mark..............................: Behringer Model and/or type reference . : AIRPLAY GUITAR ULG10 FCC Rules and Regulations Part 15 Subpart C Section 15.247 Standards...............................: ANSI C63.10: 2013 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test .............................................. : Date (s) of performance of tests.............. : Apr. 19, 2019 ~ Jun. 13, 2019 Date of Issue..........................................: Jun. 13, 2019 Test Result................................................. : Pass Prepared by: Kahn yang/Editor Reviewer: Sherwin Qian/Supervisor Approved & Authorized Signer: Liuze/Manager

Page 3 of 33 Report No.: UNIA19041914FR-01 Table of Contents Page 1 . TEST SUMMARY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 Carrier Frequency of Channels 7 2.3 Operation of EUT during testing 7 2.4 DESCRIPTION OF TEST SETUP 7 2.5 MEASUREMENT INSTRUMENTS LIST 8 3. CONDUCTED EMISSIONS TEST 9 3.1 Conducted Power Line Emission Limit 9 3.2 Test Setup 9 3.3 Test Procedure 9 3.4 Test Result 9 4 RADIATED EMISSION TEST 12 4.1 Radiation Limit 12 4.2 Test Setup 12 4.3 Test Procedure 13 4.4 Test Result 13 5 BAND EDGE 19 5.1 Limits 19 5.2 Test Procedure 19 5.3 Test Result 19 6 OCCUPIED BANDWIDTH MEASUREMENT 21 6.1 Test Limit 21 6.2 Test Procedure 21 6.3 Measurement Equipment Used 21 6.4 Test Result 21 7 POWER SPECTRAL DENSITY TEST 24 7.1 Test Limit 24 7.2 Test Procedure 24 7.3 Measurement Equipment Used 24 7.4 Test Result 24 8 PEAK OUTPUT POWER TEST 27 8.1 Test Limit 27 8.2 Test Procedure 27

Page 4 of 33 Report No.: UNIA19041914FR-01 Table of Contents Page 8.3 Measurement Equipment Used 27 8.4 Test Result 27 9 OUT OF BAND EMISSIONS TEST 28 9.1 Test Limit 28 9.2 Test Procedure 28 9.3 Test Setup 28 9.4 Test Result 28 10 ANTENNA REQUIREMENT 31 11 PHOTOGRAPH OF TEST 32 11.1 Radiated Emission 32 11.2 Conducted Emission 33

Page 5 of 33 Report No.: UNIA19041914FR-01 1. TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS DESCRIPTION OF TEST RESULT STANDARD CONDUCTED EMISSIONS TEST COMPLIANT FCC Part 15.207 RADIATED EMISSION TEST COMPLIANT FCC Part 15.209(a) BAND EDGE COMPLIANT FCC Part 15.247(d) OCCUPIED BANDWIDTH MEASUREMENT COMPLIANT FCC Part 15.247(a)(2) POWER SPECTRAL DENSITY COMPLIANT FCC Part 15.247(e) PEAK OUTPUT POWER COMPLIANT FCC Part 15.247(b) OUT OF BAND EMISSIONS COMPLIANT FCC Part 15.247(d) ANTENNA REQUIREMENT COMPLIANT FCC Part 15.203 1.2 TEST FACILITY Test Firm : Shenzhen United Testing Technology Co., Ltd. Address : 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L6494 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. Designation Number: CN1227 Test Firm Registration Number: 674885 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. 1.3 MEASUREMENT UNCERTAINTY Measurement Uncertainty Conducted Emission Expanded Uncertainty = 2.23dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 3.08dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz) = 4.42dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.06dB, k=2

Page 6 of 33 Report No.: UNIA19041914FR-01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Guitar Wireless System Trade Mark Behringer Model Name AIRPLAY GUITAR ULG10 Serial No. N/A Model Difference N/A FCC ID QWHULG10 Antenna Type PCB Antenna Antenna Gain 1dBi Frequency Range 2405~2475MHz Number of Channels 8CH Modulation Type GFSK Battery 3.7V 750mAh Power Source DC 12V from adapter withAC 120(240)V/60Hz Adapter Model Input: AC 100-240V, 50/60Hz Output: DC 5V, 1.0A Note: For more detailed features description, please refer to the manufacturer’s specifications or the User's Manual.

Page 7 of 33 Report No.: UNIA19041914FR-01 2.2 Carrier Frequency of Channels Frequency Channel Frequency Channel (MHz) (MHz) 1 2405 5 2445 2 2415 6 2455 3 2425 7 2465 4 2435 8 2475 2.3 Operation of EUT during testing Operating Mode The mode is used: Transmitting mode Low Channel: 2405MHz Middle Channel: 2445MHz High Channel: 2475MHz 2.4 DESCRIPTION OF TEST SETUP Operation of EUT during Conducted testing: AC 120V/60Hz Adapter Laptop EUT Operation of EUT during Radiation and Above1GHz Radiation testing: Laptop EUT Support Equipment Equipment Manufacturer Model Serial No. Note No. Input: 100-240V~1.7A 50-60Hz Adapter MUSIC Tribe N/A N/A Output: 20V, 2.25A Manufacturing PH Ltd.

Page 8 of 33 Report No.: UNIA19041914FR-01 2.5 MEASUREMENT INSTRUMENTS LIST Item Equipment Manufacturer Model No. Serial No. Calibrated until CONDUCTED EMISSIONS TEST 1 AMN Schwarzbeck NNLK8121 8121370 2019.9.9 2 AMN ETS 3810/2 00020199 2019.9.9 EMI TEST 3 Rohde&Schwarz ESCI 101210 2019.9.9 RECEIVER 4 AAN TESEQ T8-Cat6 38888 2019.9.9 RADIATED EMISSION TEST 1 Horn Antenna Sunol DRH-118 A101415 2019.9.29 2 BicoNILog Antenna Sunol JB1 Antenna A090215 2019.9.29 3 PREAMP HP 8449B 3008A00160 2019.9.9 4 PREAMP HP 8447D 2944A07999 2019.9.9 EMI TEST 5 Rohde&Schwarz ESR3 101891 2019.9.9 RECEIVER VECTOR Signal 6 Rohde&Schwarz SMU200A 101521 2019.9.28 Generator 7 Signal Generator Agilent E4421B MY4335105 2019.9.28 8 MXA Signal Analyzer Agilent N9020A MY50510140 2019.9.28 9 MXA Signal Analyzer Agilent N9020A MY51110104 2019.9.9 ANT Tower&Turn 10 Champro EM 1000 60764 2019.9.28 table Controller 11 Anechoic Chamber Taihe Maorui 9m*6m*6m 966A0001 2019.9.9 12 Shielding Room Taihe Maorui 6.4m*4m*3m 643A0001 2019.9.9 13 RF Power sensor DARE RPR3006W 15I00041SNO88 2020.3.14 14 RF Power sensor DARE RPR3006W 15I00041SNO89 2020.3.14 15 RF power divider Anritsu K241B 992289 2019.9.28 Wideband radio 16 Rohde&Schwarz CMW500 154987 2019.9.28 communication tester 17 Biconical antenna Schwarzbeck VHA 9103 91032360 2019.9.8 18 Biconical antenna Schwarzbeck VHA 9103 91032361 2019.9.8 Broadband Hybrid 19 Schwarzbeck VULB9163 VULB9163#958 2019.9.8 Antennas 20 Horn Antenna Schwarzbeck BBHA9120D 9120D-1680 2020.1.12 Active Receive Loop 21 Schwarzbeck FMZB 1919B 00023 2019.11.02 Antenna 22 Horn Antenna Schwarzbeck BBHA 9170 BBHA9170651 2020.03.14 Microwave 23 Broadband Schwarzbeck BBV 9721 100472 2019.10.24 Preamplifier 24 Active Loop Antenna Com-Power AL-130R 10160009 2020.05.10 25 Power Meter KEYSIGHT N1911A MY50520168 2020.05.10

Page 9 of 33 Report No.: UNIA19041914FR-01 3. CONDUCTED EMISSIONS TEST 3.1 Conducted Power Line Emission Limit For unintentional device, according to § 15.107(a) Line Conducted Emission Limits is as following Maximum RF Line Voltage(dBV) Frequency CLASS A CLASS B (MHz) Q.P. Ave. Q.P. Ave. 0.15~0.50 79 66 66~56* 56~46* 0.50~5.00 73 60 56 46 5.00~30.0 73 60 60 50 * Decreasing linearly with the logarithm of the frequency For intentional device, according to §15.207(a) Line Conducted Emission Limit is same as above table. 3.2 Test Setup 3.3 Test Procedure 1, The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. A wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10. 2, Support equipment, if needed, was placed as per ANSI C63.10. 3, All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4, If a EUT received DC power from the USB Port of Notebook PC, the PC’s adapter received AC120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5, All support equipments received AC power from a second LISN, if any. 6, The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7, Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 3.4 Test Result Pass Remark: 1. All modes were tested at AC 120V and 240V, only the worst result of AC 120V was reported. 2. All modes were tested at Low, Middle, and High channel, only the worst result of Low Channel was reported as below:

Page 10 of 33 Report No.: UNIA19041914FR-01 Temperature: 24℃ Relative Humidity: 45% Test Date: Apr. 29, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Line Test Mode: Transmitting mode of GFSK 2405MHz Remark: Factor = Insertion Loss + Cable Loss, Result = Reading + Factor, Margin = Result – Limit.

Page 11 of 33 Report No.: UNIA19041914FR-01 Temperature: 24℃ Relative Humidity: 45% Test Date: Apr. 29, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Neutral Test Mode: Transmitting mode of GFSK 2405MHz Remark: Factor = Insertion Loss + Cable Loss, Result = Reading + Factor, Margin = Result – Limit.

Page 12 of 33 Report No.: UNIA19041914FR-01 4 RADIATED EMISSION TEST 4.1 Radiation Limit For unintentional device, according to § 15.109(a), except for Class A digital devices, the field strength of radiated emissions from unintentional radiators at a distance of 3 meters shall not exceed the following values： Frequency Distance Radiated Radiated (MHz) (Meters) (dBμV/m) (μV/m) 30-88 3 40 100 88-216 3 43.5 150 216-960 3 46 200 Above 960 3 54 500 For intentional device, according to § 15.209(a), the general requirement of field strength of radiated emissions from intentional radiators at a distance of 3 meters shall not exceed the above table. 4.2 Test Setup 1. Radiated Emission Test-Up Frequency Below 30MHz 2. Radiated Emission Test-Up Frequency 30MHz~1GHz

Page 13 of 33 Report No.: UNIA19041914FR-01 3. Radiated Emission Test-Up Frequency Above 1GHz 4.3 Test Procedure 1. Below 1GHz measurement the EUT is placed on turntable which is 0.8m above ground plane. And above 1GHz measurement EUT was placed on low permittivity and low tangent turn table which is 1.5m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. 7. The test frequency range from 9KHz to 25GHz per FCC PART 15.33(a). Note: For battery operated equipment, the equipment tests shall be performed using a new battery. 4.4 Test Result PASS Remark: 1. All modes were test at Low, Middle, and High channel, only the worst result of Low Channel was reported for below 1GHz test. 2. By preliminary testing and verifying three axis (X, Y and Z) position of EUT transmitted status, it was found that “Z axis” position was the worst, and test data recorded in this report.

Page 14 of 33 Report No.: UNIA19041914FR-01 Below 1GHz Test Results: Temperature: 24℃ Relative Humidity: 45% Test Date: Apr. 29, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Polarization: Horizontal Test Mode: Transmitting mode of GFSK2405MHz Remark: Absolute Level = Reading Level + Factor, Margin = Absolute Level – Limit Factor = Ant. Factor + Cable Loss – Pre-amplifier

Page 15 of 33 Report No.: UNIA19041914FR-01 Temperature: 24℃ Relative Humidity: 45% Test Date: Apr. 29, 2019 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Polarization: Vertical Test Mode: Transmitting mode of GFSK2405MHz Remark: Absolute Level = Reading Level + Factor, Margin = Absolute Level – Limit Factor = Ant. Factor + Cable Loss – Pre-amplifier Remark： (1) Measuring frequencies from 9 kHz to the 1 GHz, radiated emission test from 9KHz to 30MHz was verified, and no any emission was found except system noise floor. (2) * denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. (3) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz.

Page 16 of 33 Report No.: UNIA19041914FR-01 Above 1 GHz Test Results: Channel: 2405MHz Horizontal: Reading Frequency Result Factor Emission Level Limits Margin Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 4810 71.3 -3.74 67.6 74 -6.40 peak 4810 50.0 -3.74 46.3 54 -7.70 AVG 7215 60.0 -0.98 59.0 74 -15.00 peak 7215 50.3 -0.98 49.3 54 -4.70 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit Vertical: Reading Frequency Result Factor Emission Level Limits Margin Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 4810 57.9 -3.74 54.2 74 -19.80 peak 4810 50.1 -3.74 46.4 54 -7.60 AVG 7215 58.5 -0.98 57.5 74 -16.50 peak 7215 47.5 -0.98 46.5 54 -7.50 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit

Page 17 of 33 Report No.: UNIA19041914FR-01 Middle Channel: 2445MHz Horizontal: Reading Frequency Factor Emission Level Limits Margin Result Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 4890 60.1 -3.61 56.5 74 -17.50 peak 4890 48.2 -3.61 44.6 54 -9.40 AVG 7335 60.6 -0.91 59.7 74 -14.30 peak 7335 49.7 -0.91 48.8 54 -5.20 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit Vertical: Reading Frequency Factor Emission Level Limits Margin Result Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 4890 58.3 -3.61 54.7 74 -19.30 peak 4890 47.9 -3.61 44.3 54 -9.70 AVG 7335 59.3 -0.91 58.4 74 -15.60 peak 7335 48.0 -0.91 47.1 54 -6.90 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit

Page 18 of 33 Report No.: UNIA19041914FR-01 High Channel: 2475MHz Horizontal: Reading Frequency Result Factor Emission Level Limits Margin Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 4950 60.35 -3.43 56.92 74 -17.08 peak 4950 50.26 -3.43 46.83 54 -7.17 AVG 7425 54.99 -0.75 54.24 74 -19.76 peak 7425 47.06 -0.75 46.31 54 -7.69 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit Vertical: Reading Frequency Result Factor Emission Level Limits Margin Detector (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type 4950 61.84 -3.43 58.41 74 -15.59 peak 4950 51.21 -3.43 47.78 54 -6.22 AVG 7425 56.35 -0.75 55.60 74 -18.40 peak 7425 46.06 -0.75 45.31 54 -8.69 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit Remark： (1) Measuring frequencies from 1 GHz to the 25 GHz。 (2) “F” denotes fundamental frequency; “H” denotes spurious frequency. “E” denotes band edge frequency. (3) * denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. (4) Data of measurement within this frequency range shown “---” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. (5) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for peak measurement with peak detector at frequency above 1GHz. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 10Hz for Average measurement with peak detection at frequency above 1GHz. (6) When the test results of Peak Detected below the limits of Average Detected, the Average Detected is not need completed. For example: Top Channel at Fundamental 73.16dBuV/m (PK Value) <93.98(AV Limit), at harmonic 53.20 dBuV/m (PK Value) <54 dBuV/m (AV Limit), the Average Detected not need to completed.

Page 19 of 33 Report No.: UNIA19041914FR-01 5 BAND EDGE 5.1 Limits FCC PART 15.247 Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in §15.209, whichever is the lesser attenuation. 5.2 Test Procedure The band edge compliance of RF radiated emission should be measured by following the guidance in ANSI C63.10 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the measurement antenna height and polarization etc. Set RBW 1MHz VBW 3MHz PK detector is for PK value , RMS detector is for AV value. 5.3 Test Result PASS Operation Mode: Low Channel: 2405MHz Horizontal: Frequency Reading Result Factor Emission Level Limits Margin Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2310 56.21 -5.81 50.4 74 -23.6 peak 2310 / -5.81 / 54 / AVG 2390 61.34 -5.84 55.5 74 -18.5 peak 2390 49.04 -5.84 43.2 54 -10.8 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Vertical: Frequency Reading Result Factor Emission Level Limits Margin Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2310 56.11 -5.81 50.3 74 -23.7 peak 2310 / -5.81 / 54 / AVG 2390 64.04 -5.84 58.2 74 -15.8 peak 2390 54.34 -5.84 48.5 54 -5.5 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Page 20 of 33 Report No.: UNIA19041914FR-01 Operation Mode: High Channel: 2475MHz Horizontal: Frequency Reading Result Factor Emission Level Limits Margin Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2483.5 57.13 -5.65 51.48 74 -22.52 peak 2483.5 / -5.65 / 54 / AVG 2500 56.35 -5.72 50.63 74 -23.37 peak 2500 / -5.72 / 54 / AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Vertical: Frequency Reading Result Factor Emission Level Limits Margin Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2483.5 56.35 -5.65 50.7 74 -23.3 peak 2483.5 / -5.65 / 54 / AVG 2500 57.23 -5.72 51.51 74 -22.49 peak 2500 / -5.72 / 54 / AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Page 21 of 33 Report No.: UNIA19041914FR-01 6 OCCUPIED BANDWIDTH MEASUREMENT 6.1 Test Limit FCC Part15(15.247), Subpart C Frequency Range Section Test Item Limit Result (MHz) >= 500KHz 15.247(a)(2) Bandwidth 2400-2483.5 PASS (6dB bandwidth) 6.2 Test Procedure 1. The EUT was placed on a table which is 0.8m above ground plane. 2. Set EUT as normal operation. 3. Based on FCC Part15 C Section 15.247: RBW=100KHz, VBW=300KHz. 4. The useful radiated emission from the EUT was detected by the spectrum analyzer with peak detector. 6.3 Measurement Equipment Used Same as Radiated Emission Measurement 6.4 Test Result PASS

Page 22 of 33 Report No.: UNIA19041914FR-01 TX 802.11b Mode 6dB Bandwidth Channel Separation Frequency Result (MHz) (MHz) 2405 MHz 1.323 >=500KHz PASS 2445 MHz 1.447 >=500KHz PASS 2475 MHz 1.376 >=500KHz PASS CH: 2405MHz

Page 23 of 33 Report No.: UNIA19041914FR-01 CH: 2445MHz CH: 2475MHz

Page 24 of 33 Report No.: UNIA19041914FR-01 7 POWER SPECTRAL DENSITY TEST 7.1 Test Limit FCC Part15(15.247), Subpart C Frequency Range Section Test Item Limit Result (MHz) Power Spectral 8 dBm 15.247 2400-2483.5 PASS Density (in any 3KHz) 7.2 Test Procedure 1. The EUT was placed on a table which is 0.8m above ground plane. 2. Set EUT as normal operation. 3. Based on FCC Part15 C Section 15.247: RBW=3KHz, VBW≥3RBW. 4. The useful radiated emission from the EUT was detected by the spectrum analyzer with peak detector. 7.3 Measurement Equipment Used Same as Radiated Emission Measurement 7.4 Test Result PASS

Page 25 of 33 Report No.: UNIA19041914FR-01 TX Mode Power Density Limit Frequency Result (dBm/3KHz) (dBm/3KHz) 2405 MHz -13.094 8 PASS 2445 MHz -14.538 8 PASS 2475 MHz -11.684 8 PASS CH: 2405MHz

Page 26 of 33 Report No.:UNIA19041914FR-01 CH: 2445MHz CH: 2475MHz

Page 27 of 33 Report No.: UNIA19041914FR-01 8 PEAK OUTPUT POWER TEST 8.1 Test Limit FCC Part15(15.247), Subpart C Frequency Range Section Test Item Limit Result (MHz) Peak Output 15.247(b)(3) 1 watt or 30dBm 2400-2483.5 PASS Power 8.2 Test Procedure 1. The EUT was placed on a table which is 0.8m above ground plane. 2. The EUT was directly connected to the Power meter. 8.3 Measurement Equipment Used Same as Radiated Emission Measurement 8.4 Test Result PASS All the test modes completed for test. TX Mode Test Frequency Maximum Peak Conducted Output Power LIMIT Channel (MHz) (dBm) (dBm) CH1 2405 8.684 30 CH9 2445 7.698 30 CH16 2475 7.985 30

Page 28 of 33 Report No.: UNIA19041914FR-01 9 OUT OF BAND EMISSIONS TEST 9.1 Test Limit In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. 9.2 Test Procedure 1. The EUT was placed on a table which is 0.8m above ground plane. 2. Set EUT as TX operation and connect directly to the spectrum analyzer. 3. Based on FCC Part15 C Section 15.247: RBW=100KHz, VBW=300KHz. 4. Set detected by the spectrum analyzer with peak detector. 9.3 Test Setup Spectrum EUT Analyzer 9.4 Test Result PASS

Page 29 of 33 Report No.: UNIA19041914FR-01 Reference (Test Channel: 2405MHz) TX Mode CH: 2405MHz

Page 30 of 33 Report No.: UNIA19041914FR-01 Reference (Test Channel: 2475MHz) TX Mode CH: 2475MHz

Page 31 of 33 Report No.: UNIA19041914FR-01 10 ANTENNA REQUIREMENT Standard Applicable: For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. Antenna Connected Construction The antenna used in this product is an PCB Antenna, the directional gains of antenna used for transmitting is 1dBi. WIFI ANTENNA

Page 32 of 33 Report No.: UNIA19041914FR-01 11 PHOTOGRAPH OF TEST 11.1 Radiated Emission

Page 33 of 33 Report No.: UNIA19041914FR-01 11.2 Conducted Emission ***End of Report***


Document Created: 2019-07-10 19:00:56
Document Modified: 2019-07-10 19:00:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC