LMA letter

FCC ID: QTG-ZKMS

Cover Letter(s)

Download: PDF
FCCID_2451099

Applicant ZAGG Inc. FCC ID: QTG-ZKMS Section 15.212 Modular Transmitters Request for Modular Approval N/A Request for Limited Modular Approval Y Comply Requirements EUT Conditions (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular No, this RF Module has no own RF N transmitter must have their own shielding and therefore does not comply shielding. The physical crystal and to this requirement. Limited Modular tuning capacitors may be located Approval is applied. The RF Module is external to the shielded radio subject to Professional Installation elements. and Integrator is advised by the integration manual how to assure compliance of final end-product into which this RF Module is integrated to the FCC regulations. 2 The modular transmitter must have Please refer the Schematic, The modular Y buffered modulation/data inputs (if transmitter have buffered modulation/data such inputs are provided) to ensure inputs U1 that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. 3 The modular transmitter must have its Complies, this RF Module has own Y own power supply regulation. power supply regulation, please refer to schematics (U1). 4 The modular transmitter must comply Referring to onboard PCB antenna Y with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section.

5 The modular transmitter must be Does not comply. Due to the fact that this N tested in a stand-alone configuration, RF Module is not equipped with an own i.e., the module must not be inside RF shielding, the radiated measurements another device during testing for are performed with the RF Module compliance with Part 15 requirements. installed in a dedicated host / host Unless the transmitter module will be platform (here BT Keyboard). battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)).

6 The modular transmitter must be The modular was labeled with its own Y equipped with either a permanently FCC ID. The outside of device in to affixed label or must be capable of which the module is installed will electronically displaying its FCC labeled ‘Contains TX FCC identification number. (A) If using a ID:QTG-ZKMS, Please refer to User permanently affixed label, the modular Manual transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: QTG-ZKMS” or “Contains FCC ID: QTG-ZKMS.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization.

7 The modular transmitter must comply This RF Module will exclusively Y with any specific rules or operating integrated into battery power host requirements that ordinarily apply to a devices. The integration limitations are complete transmitter and the clearly addressed within the integration manufacturer must provide adequate manual, please refer to the User Manual. instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. 8 The modular transmitter must comply With the documented max output power Y with any applicable RF exposure this RF Module meets the FCC SAR requirements in its final configuration. Exemption,so it can comply with any applicable RF exposure requirements in its final configuration. A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured. ZAGG Inc. Contact person: Paul Faerber Title: Director of Product Development


Document Created: 2014-11-20 09:44:06
Document Modified: 2014-11-20 09:44:06
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC