Users Manual

FCC ID: QSRPT-400

Users Manual

Download: PDF
FCCID_1167584

eT2733d UHF PROFESSIONAL WIRELESS MICROPHONE OPERATING INSTRUCTIONS Copyright 2008,Karsect Incorporated The vocal artis UHF www. karsect. com. The presenter UHF The headset ______________———UHF The guitarist —__—_—_—_—_—_————————UHF

Contents Foreword Thank you for purchasing this product, please read this manual carefully so that you can understand how to operate the system properly. Please keep this 1. Contents / Attentions..............................................................................1 manual in a safe place after reading as a reference in the future. This series of professional wireless microphone system used with high efficient, 2. Foreword / System Introduction / System Feature/ System Type.................2 low consumption RF transmission and super sensitive RF receiving technique, apply an independent. 3. WR400&4Front and rear panel function instruction....................................3 developed dynamic audio compression, expander circuit, image frequency limiting circuit, multi-detecting squelch circuit, numeral pilot carrier detecting 4. HT400 / PT400 Transmitter function instruction........................................4 squelch circuit, antenna diversity receiving circuit, switch impact noise defeat circuit, resist reverberation circuit, graded output control ect...Adopt 5. HT400 / PT400 Transmitter battery installation.........................................5 computer EDA simulating on line auxiliary design and strict quality control to gain the excellent function for each system. 6. Three type of PT400 Transmitter connection .........................................6 7. System Connection...............................................................................7 System Introduction This series of wireless system will give you the super audio quality and eximious 8. Receiver installation in 19 inch equipment rack.....................................8 freedom on moving. This manual cover each of system: The Vocal Artist-UHF The Presenter-UHF, The Headset-UHFand The Guitarist-UHF. 9. Specification.........................................................................................9 System Feature 1. Diversity circuit with automatic signal selection to improve the receiving effect, effectively clean up the signal blind spot in using. Attentions 2. Design with an antenna signal splitter of eight channel inside, extremely balance to distribute the RF signal from antenna to each receiving module evenly. 1. The minimum space around equipment should be more than 30cm to keep 3. To determine the final choice for analysis of signal strength and signal quality by squelch circuit design, effect to reduce the pulse train of RF noises in using enough ventilation. environment. 4. One 100mA/10.5V DC voltage is output from two antenna input, supplied for 2. Please don't cover the vent hole of equipment to block the ventilation by news the using of external antenna amplifier to extend the system receiving distance. 5. Design with four XLR output connectors in 0dB output and input, they can be paper, table cloth and window curtain.... connected to the external audio equipment. 6. Bodypack transmitter with selecting switch for Lavalier/Headset/Guitarist, 3. Please don't put any fire on the equipment, such as burning candle. suitable for the system using demand. 7. Supply the power to four receiver modules independently for exclusive use. 4. Please don't clear the equipment by water and wet cloth to avoid the damage. 8. ELA standard 19 inch full metal housing. 9. Separate modules design in draw easily, convenient to use and easy to repair 5. Please don't put any liquid fulled substance on the equipment such as vase... and upgrade. 10. Adopt precise high frequency radiant protection technique, high sensitivity, 6. Scrap battery have an effect to environment, please do not throw out anywhere, low noise and harmonic radiation, long receiving distance, steady receivin.g put them into appointed recycle bin. System type 1. The Vocal Artist-UHF is a handheld system designed for singers who desire the high quality of microphone and the freedom of wireless performance. 2. The Presenter-UHF is a bodypack system designed for public speakers who prefer an inconspicuous, handfree lavalier microphone. 3. The Headset-UHF is a bodypack system designed for users in physically active applications who desire the freedom of hand-free microphone. 4. The Guitarist-UHF is a bodypack system designed for users with electric guitars, basses and other electric instrument. 1 2

WR400& 4 Front& rear panel function/ instruction HT400 Transmitter Function/Instruction (1) ( 6 )(7) (6)(7) ( 6 )( 7 ) ( 6 )( 7 ) (3) ( 2 ) (1) (6) AA L M H (4)(8)( 5 ) (4)(8)( 5 ) (4)(8)( 5 ) (4)(8)( 5 ) AA Front Panel (3) (4) (10 )( 1 1 )(12) (1 2 ) (13)(14) ( 1 2 ) (12) (9) (2) ON OF F (5) 1. Grille: Protects the cartridge and help reducing the breath sounds and wind noise. Rear Panel 2. Battery Cover: Open it to install the battery. 3. Battery Cover Lock: lock or unlock the battery cover. 4. Low Battery Indicator: Red light glows when it is lack of power and should 1. Front Antenna Hole A: Move the receiving antenna to front panel. renew the battery. 2. Front Antenna Hole B: Move the receiving antenna to front panel. 5. Power Switch: Power ON/OFF the transmitter. 3. Power Switch: Power ON/OFF the receiver. 6. Gain Adjustment: Adjust the transmitter audio input gain in high, middle or Low levels 4. Squelch Adjusting Knob: Adjust the squelch sensitivity of receiver to strengthen PT400 Transmitter Function/Instruction the signal quality or system receiving distance. This knob is factory pre-set, ( 4 )( 5) normally no further adjustment is required. 5. Volume Adjusting knob: Adjust the volume output of receiver. ( 2) 6. Antenna Diversity Signal Indicators:indicate the receiver signal is from antenna “A”or“B”. (1) ( 6 ) (7) 7. AF Peak Indicator: Indicate the receiver audio signal strength. (3) 8. Power Indicator: Indicate the receiver power state. 9. Antenna“A”( TNC) : Receiverd the RF signal from transmitter. L H G 10. Antenna“B”( TNC) : Receiverd the RF signal from transmitter. 1. 5V 11. 1/ 4' Phone Jack Audio Output Connector( Unbalanced impedance) : 1. 5V An unbalanced audio cable with 1/ 4' phone jack can be connected to 1. Power Switch: Power ON/OFF the transmitter. 2. Antenna: Transmit the RF signal of transmitter. the input of amplifier/ audio mixer. 3. Belt Clip: Gird the transmitter to the belt or guitar strap. 12.XLR Audio Output Connector(Balanced Output): A balanced audio cable 4. Audio Input Jack: It is TAF 3 pins connector, it is suitable for lavalier system/ with XLR plug can be connected to the input of amplifier/ audio mixer. Headset system/guitar and instrument system. 5. Low Battery Indicator: Red light glows when it is lack of power and should 13.Power Switch For Each Receiving Module:Power on the receiving modules Renew the battery. separately. 6. State Setting Switch: Set the using state to lavalier system/headset system/ 14.Power Jack:Connect the Power AC/DC adapter to receiver. guitar system. 7. Gain Adjustment: Adjust the transmitter audio input gain. 3 4

Transmitter Battery Installation Three Types of Bodypack Transmitter Connection 1 . L a v a l i e r M i c r o p h o n e C o n n e c t i o n : C o n n e c t t h e TA F 3 p i n s c o n n e c t e r o f 1. Battery Installation of Handheld Microphone: Unlock the battery cover and supplied lavalier cable to the TAF3 pins connecting jack of transmitter (Shown take it out, insert the supplied batteries into battery jar in polarity and cover as below), set the transmitter work state in wireless lavalier system . the battery cover, then lock. 2 . H e a d s e t M i c r o p h o n e C o n n e c t i o n : C o n n e c t t h e TA F 3 p i n s c o n n e c t e r o f supplied headset microphone to the TAF3 pins connecting jack of transmitter (Shown as below), set the transmitter work state in wireless headset system . 2. Battery Installation of Bodypack Transmitter: Press down the lock on battery cover open it, insert the supplied batteries into battery jar in polarity and close to lock battery cover. 3 . G u i t a r i s t M i c r o p h o n e C o n n e c t i o n : C o n n e c t t h e TA F 3 p i n s c o n n e c t e r o f supplied guitar cable to the TAF3 pins connecting jack of transmitter (Shown as below), set the transmitter work state in wireless guitarist system. 5 6

System Connection Receiver Installation in 19 Inch Equipment Rack Put the receiver into a suitable position of 19 inch equipment rack, tighten with 1. Receiver Power Connection: Connect the DC connector of supplied AC/DC four fixed screw so that the receiver can be installed to the rack easily. adapter into the DC power input of receiver. Plug the AC input connecter into an AC120/60Hz or AC220V/50Hz outlet. (Shown as below) 2. Antenna Connection: Install two antennas to the antenna input of receiver respectively, keep the position of antenna at a 45 angle from vertical, then tighten the screw.(Sh own as below) 45 3. Audio Connection: Connect the corresponding output of receiver by supplied 1/4" phone jack audio cable or your XLR cable to the input of power amplifier or mixer.(Shown as below) 8 7

Specification System specification. 1. Frequency range: 720.00—865.00MHz (Available frequencies depend on the applicable regulations in the country where the system is used) . Frequency stability: <+/—15ppm m . S/N Ratio: >85dB s o . Total harmonic distortion(THD): <0.5% . Frequency response: 50Hz——15KHz (+2d0B) ~ o a . Audio output level: 360mV . Working distance: 100 meters (In good condition) . Operating temperature: —10~50 degree o Receiver specification . Sensitivity: >—105dBm (S/N: —12dB/15KHz) — . Border upon channel rejection: >75dB m . RF image spurious rejection: >75dB m w . Power requirement: 13——15V/DC . Power consumption: <30W a . Size: 48 x 21 x 5 cm o Handheld transmitter specification . RF power: 10dBm (50 2 ) — . Harmonic rejection: >—60dBc m . Max. frequency deviation: >65KHz s o . Current consumption: <95mA (2AA) . Cartridge: Dynamic/Cardioid ~ o . Battery: 2XAA (Alkaline battery) . Battery life: Approx. 8 hours (1800mAh) ® Bodypack transmitter specification . RF power: 10dBm (500) — . Harmonic rejection: >—60dBc No . Max. frequency deviation: >65KHz a w . Current consumption: <95mA (2AA) . Cartridge: Condenser/Cardioid ~ o a . Battery: 2XAA (Alkaline battery) . Battery life: Approx. 8 hours (1800mAh) $ 10


Document Created: 2019-09-01 22:19:59
Document Modified: 2019-09-01 22:19:59
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC