Modular Request Letter

FCC ID: QOQWF121

Cover Letter(s)

Download: PDF
FCCID_1801761

Gpgs:s MODULAR APPROVAL REQUEST 10.07.2012 RE: FCC Modular Approval FCC ID: QOQWwF121 Dear Application Examiner Bluegiga Technologies Oy / Bluetooth module, FCC ID: QOQWF121, would like to have your authorization as a modular approval. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. The modular transmitter must The module has its own RF have its own RF shielding. shielding The modular transmitter must The module has buffered data have buffered modulation/data inputs inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over— modulation. The modular transmitter must The module has its own power have its own power supply supply regulation regulation. The modular transmitter must The module has a embedded comply with the antenna chip antenna or a unique RF requirements of Section 15.203 coupler for an external antenna and 15.204(c). The antenna as an assembly variant. The must either be permanently antenna coupler can be either a attached or employ a "unique" RF pin or an u.fl connector. antenna coupler (at all Instructions for the OEM are connections between the module given in the user manual and the antenna, including the (datasheet). cable). Any antenna used with the module must be approved Bluegiga Technologies Sinikalliontie 5A, P.O. Box 120 02630 Espoo FINLAND Tel +358 9 435 5060 | Fax +358 9 435 50660 Co ID 0934238—1, VAT registered, domicile: Espoo www.bluegiga.com | sales@bluegiga.com

Gpss:ss with the module, either at the time of initial authorization or through a Class II permissive change. The "professional installation" provision of Section 15.203 may not be applied to modules. The modular transmitter must be The module was tested in a tested in a stand—alone stand alone configuration using a configuration, i.e., the module test kit. must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the ransmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). The modular transmitter must be Please see exhibition label labeled with its own FCC ID sample for the FCC ID of this number, and, if the FCC ID is not module. And also in the Bluegiga Technologies Sinikalliontie 5A, P.O. Box 120 02630 Espoo FINLAND Tel +358 9 435 5060 | Fax +358 9 435 50660 Co ID 0934238—1, VAT registered, domicile: Espoo www.bluegiga.com | sales @bluegiga.com

Gmgs:ss visible when the module is exhibition User manual, there installed inside another device, are instructions to give to the then the outside of the device OEM on how to label the end into which the module is product. installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmitter Module FCC ID: XYZMODEL1" or "Contains FCC ID: XYZMODEL1." Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. The modular transmitter must The module is compliant with all comply with any specific rule or applicable FCC rules. Detailed operating requirements instructions for remaining applicable to the transmitter and compliance are given in the User the manufacturer must provide Manual (datasheet). adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, Bluegiga Technologies Sinikalliontie 5A, P.O. Box 120 02630 Espoo FINLAND Tel +358 9 435 5060 | Fax +358 9 435 50660 Co ID 0934238—1, VAT registered, domicile: Espoo www.bluegiga.com | sales @bluegiga.com

except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. The modular transmitter must The module complies with RF comply with any applicable RF exposure requirement. RF exposure requirements. For exposure is addressed in the RF example, FCC Rules in Sections exposure exhibition. 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Best regards %— P4 Pasi Rahikkala, HW Compliance Engineer Bluegiga Technologies Oy Bluegiga Technologies Sinikalliontie 5A, P.O. Box 120 02630 Espoo FINLAND Tel +358 9 435 5060 | Fax +358 9 435 50660 Co ID 0934238—1, VAT registered, domicile: Espoo www.bluegiga.com | sales @bluegiga.com


Document Created: 2012-07-11 15:02:11
Document Modified: 2012-07-11 15:02:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC