Modular approval request letter_v2

FCC ID: QOQ11

Cover Letter(s)

Download: PDF
FCCID_3425219

SILICON LABS MODULAR APPROVAL REQUEST 13.4.2017 RE: FCC ModularApproval FCC ID: QoQ11 Dear Application Examiner Bluegiga Technologies Inc. / Blustooth module, FCC ID: QOQ11, would like to have your authorization as a modular approval. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. REQUIREMENT Yes / No COMMENT The modular transmitter YES The module has a shield must have its own RF shielding. The modular transmitter YES The module has buffered data inputs must have buffered integrated to EFRSZ chip modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over— modulation. The modular transmitter YES The module has its own power supply must haveits own power regulation. supply regulation. The modular transmitter YES An embedded chip antenna is must comply with the permanently attached to the BGM11S1A antenna requirements of and BGM11S2A. Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a "unique" antenna coupler (at all connections between the module and the antenna, including the cable). Any antenna used with the module must be approved with the module, either at the

time of inftial authorization or through a Class II permissive change. The "professional installation" provision of Section 15.203 may not be applied to modules. The modular transmitter YES The module was tested in a standalone must be tested in a stand— configuration using a test kit. alone configuration, Le., the module must not be inside anotherdevice during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the ransmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(}). The modular transmitter YES The module is labeled with its own FCC must be labeled with its ID number own FCC ID number, and, if the FCC ID is not visible when the moduleis installed inside another

device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmitter Module FCC ID: XYZMODEL1® or "Contains FCC ID: XYZMODEL1." Any similar wording that expresses the same meaning may be used. The Grantee may sither provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. The modular transmitter YES The module is compliant with all must comply with any applicable FCC rules. Detailed specific rule or operating instructions for remaining compliance are requirements applicable to given in the User Manual (datasheet). the transmifter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitteris authorized for operation under Section 15.231. For instance, data

transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. The madular transmitter YESs The module complies with RF exposure must comply with any requirement. RF exposureis addressed in applicable RF exposure the RF exposure exhibition. requirements. For example, FCC Rules in Sections 2.1091, 2.1098 and specific Sections of Part 15, including 15.319(), 15.407(0, 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Best regards 62— Pasi Rahikkala, Staff HW Engineer Silicon Labs


Document Created: 2017-04-13 10:33:05
Document Modified: 2017-04-13 10:33:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC