Test Report

FCC ID: QOB45138

Test Report

Download: PDF
FCCID_889481

Jasco Products Company Application For Certification (FCC ID: QOB45138) Transmitter 0725002 BH/ SL December 31, 2007 - The evaluation data of the report will be kept for 3 years from the date of issuance. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com

INTERTEK TESTING SERVICES LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information FCC ID: QOB45138 i

INTERTEK TESTING SERVICES MEASUREMENT/TECHNICAL REPORT Jasco Products Company - MODEL: 45138 FCC ID: QOB45138 December 31, 2007 This report concerns (check one:) Original Grant X Class II Change Equipment Type: DSR - Part 15 Remote Control/Security Device Transceiver (example: computer, printer, modem, etc.) Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [05-04-07 Edition] provision. Report prepared by: Ho Wai Kin, Ben Intertek Testing Services Hong Kong Ltd. 2/F., Garment Center, 576, Castle Peak Road, Kowloon, Hong Kong. Phone: 852-2173-8505 Fax: 852-2371-0521 FCC ID: QOB45138 ii

INTERTEK TESTING SERVICES Table of Contents 1.0 General Description ............................................................................................ 2 1.1 Product Description ............................................................................................ 2 1.2 Related Submittal(s) Grants ............................................................................... 2 1.3 Test Methodology............................................................................................... 3 1.4 Test Facility........................................................................................................ 3 2.0 System Test Configuration ................................................................................. 5 2.1 Justification ........................................................................................................ 5 2.2 EUT Exercising Software.................................................................................... 5 2.3 Special Accessories ........................................................................................... 5 2.4 Equipment Modification ...................................................................................... 6 2.5 Measurement Uncertainty .................................................................................. 6 2.6 Support Equipment List and Description ............................................................. 6 3.0 Emission Results ................................................................................................ 8 3.1 Field Strength Calculation................................................................................... 9 3.2 Radiated Emission Configuration Photograph................................................... 10 3.3 Radiated Emission Data ................................................................................... 11 3.4 Conducted Emission Configuration Photograph................................................ 13 3.5 Conducted Emission Data .....................................................................................14 4.0 Equipment Photographs................................................................................... 16 5.0 Product Labelling .............................................................................................. 18 6.0 Technical Specifications................................................................................... 20 7.0 Instruction Manual ............................................................................................ 22 8.0 Miscellaneous Information ............................................................................... 24 8.1 Measured Bandwidth........................................................................................ 25 8.2 Discussion of Pulse Desensitization.................................................................. 26 8.3 Calculation of Average Factor........................................................................... 27 8.4 Emissions Test Procedures .............................................................................. 28 FCC ID: QOB45138 iii

INTERTEK TESTING SERVICES List of attached file Exhibit type File Description filename Cover Letter Letter of Agency letter.pdf Test Report Test Report report.pdf Operation Description Technical Description descri.pdf Test Setup Photo Radiated Emission radiated photos.doc Test Setup Photo Conducted Emission conducted photos.doc Test Report Conducted Emission Test Result conducted.pdf Test Report Bandwidth Plot bw.pdf External Photo External Photo external photos.doc Internal Photo Internal Photo internal photos.doc Block Diagram Block Diagram block.pdf Schematics Circuit Diagram circuit.pdf ID Label/Location Label Artwork and Location label.pdf User Manual User Manual manual.pdf Test Report Timing Diagram timing.pdf FCC ID: QOB45138 iv

INTERTEK TESTING SERVICES EXHIBIT 1 GENERAL DESCRIPTION FCC ID: QOB45138 1

INTERTEK TESTING SERVICES 1.0 General Description 1.1 Product Description The Equipment Under Test (EUT) is a Transceiver (Repeater) operating at 318MHz. The EUT is powered by 120Vac/60Hz. During the normal operation, EUT is designed to increase the range of the sensors by boosting and repeating signal from sensors to receiver unit. The transmitter should automatically cease transmission within 600 ms after activation. Antenna Type : External, Integral For electronic filing, the brief circuit description is saved with filename: descri.pdf. 1.2 Related Submittal(s) Grants This is an application for certification of a transmitter portion of 318MHz Transceiver. The receiver portion of this transceiver was subjected to FCC Part 15 Verification Procedure. The other unit, associated with this EUT, has FCC ID: QOB45130. 45138 FCC ID: QOB45138 2

INTERTEK TESTING SERVICES 1.3 Test Methodology Both AC mains line-conducted and radiated emission measurements were performed according to the procedures in ANSI C63.4 (2003). All measurements were performed in Open Area Test Sites. Preliminary scans were performed in the Open Area Test Sites only to determine worst case modes. All Radiated tests were performed at an antenna to EUT distance of 3 meters, unless stated otherwise in the “Justification Section” of this Application. 1.4 Test Facility The open area test site and conducted measurement facility used to collect the emission data is located at Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. This test facility and site measurement data have been fully placed on file with the FCC. FCC ID: QOB45138 3

INTERTEK TESTING SERVICES EXHIBIT 2 SYSTEM TEST CONFIGURATION FCC ID: QOB45138 4

INTERTEK TESTING SERVICES 2.0 System Test Configuration 2.1 Justification The system was configured for testing in a typical fashion (as a customer would normally use it), and in the confines as outlined in ANSI C63.4 (2003). The EUT was powered from 120Vac/60Hz. For maximizing emissions, the EUT was rotated through 360°, the antenna height was varied from 1 meter to 4 meters above the ground plane, and the antenna polarization was changed. This step by step procedure for maximizing emissions led to the data reported in Exhibit 3.0. The unit was placed in the center of the turntable. The equipment under test (EUT) was configured for testing in a typical fashion (as a customer would normally use it). The EUT was placed on turntable, which enabled the engineer to maximize emissions through its placement in the three orthogonal axes. For simplicity of testing, the unit was wired to transmit continuously. The frequency range from 9kHz to 3.2GHz was searched for spurious emissions from the device. Only those emissions reported were detected. All other emissions were at least 20 dB below the applicable limits. 2.2 EUT Exercising Software There was no special software to exercise the device. Once the button is depressed, the unit transmits the typical signal. For simplicity of testing, the unit was wired to transmit continuously. 2.3 Special Accessories There are no special accessories necessary for compliance of this product. FCC ID: QOB45138 5

INTERTEK TESTING SERVICES 2.4 Equipment Modification Any modifications installed previous to testing by Jasco Products Company will be incorporated in each production model sold/leased in the United States. No modifications were installed by Intertek Testing Services Hong Kong Ltd. 2.5 Measurement Uncertainty When determining the test conclusion, the Measurement Uncertainty of test has been considered. 2.6 Support Equipment List and Description This product was tested in a standalone configuration. All the items listed under section 2.0 of this report are Confirmed by: Ho Wai Kin, Ben Supervisor Intertek Testing Services Hong Kong Ltd. Agent for Jasco Products Company Signature December 31, 2007 Date FCC ID: QOB45138 6

INTERTEK TESTING SERVICES EXHIBIT 3 EMISSION RESULTS FCC ID: QOB45138 7

INTERTEK TESTING SERVICES 3.0 Emission Results Data is included worst case configuration (the configuration which resulted in the highest emission levels). A sample calculation, configuration photographs and data tables of the emissions are included. FCC ID: QOB45138 8

INTERTEK TESTING SERVICES 3.1 Field Strength Calculation The field strength is calculated by adding the reading on the Spectrum Analyzer to the factors associated with preamplifiers (if any), antennas, cables, pulse desensitization and average factors (when specified limit is in average and measurements are made with peak detectors). A sample calculation is included below. FS = RA + AF + CF - AG + PD + AV where FS = Field Strength in dBµV/m RA = Receiver Amplitude (including preamplifier) in dBµV CF = Cable Attenuation Factor in dB AF = Antenna Factor in dB AG = Amplifier Gain in dB PD = Pulse Desensitization in dB AV = Average Factor in -dB In the radiated emission table which follows, the reading shown on the data table may reflect the preamplifier gain. An example of the calculations, where the reading does not reflect the preamplifier gain, follows: FS = RA + AF + CF - AG + PD + AV Assume a receiver reading of 62.0 dBµV is obtained. The antenna factor of 7.4 dB and cable factor of 1.6 dB is added. The amplifier gain of 29 dB is subtracted. The pulse desensitization factor of the spectrum analyzer was 0 dB, and the resultant average factor was -10 dB. The net field strength for comparison to the appropriate emission limit is 32 dBµV/m. This value in dBµV/m was converted to its corresponding level in µV/m. RA = 62.0 dBµV AF = 7.4 dB CF = 1.6 dB AG = 29.0 dB PD = 0 dB AV = -10 dB FS = 62 + 7.4 + 1.6 - 29 + 0 + (-10) = 32 dBµV/m Level in µV/m = Common Antilogarithm [(32 dBµV/m)/20] = 39.8 µV/m FCC ID: QOB45138 9

INTERTEK TESTING SERVICES 3.2 Radiated Emission Configuration Photograph Worst Case Radiated Emission at 317.973 MHz For electronic filing, the worst case radiated emission configuration photograph is saved with filename: radiated photos.doc. FCC ID: QOB45138 10

INTERTEK TESTING SERVICES 3.3 Radiated Emission Data The data on the following page lists the significant emission frequencies, the limit and the margin of compliance. Numbers with a minus sign are below the limit. Judgement: Passed by 22.9 dB TEST PERSONNEL: Signature Mark Cheung, Compliance Engineer Typed/Printed Name December 31, 2007 Date FCC ID: QOB45138 11

INTERTEK TESTING SERVICES Applicant: Jasco Products Company Date of Test: November 01, 2007 Model: 45138 Table 1 Radiated Emissions Polarization Frequency Reading Antenna Pre- Average Net Limit Margin (MHz) (dBμV) Factor Amp Factor at 3m at 3m (dB) (dB) Gain (-dB) (dBμV/m) (dBμV/m) (dB) H 317.973 66.0 23.0 16 20.1 52.9 75.8 -22.9 H 635.946 34.0 29.0 16 20.1 26.9 55.8 -28.9 H 953.919 28.3 33.0 16 20.1 25.2 55.8 -30.6 H 1271.892 49.9 26.1 33 20.1 22.9 55.8 -32.9 H 1589.865* 48.3 27.2 33 20.1 22.4 54.0 -31.6 H 1907.838 46.9 27.2 33 20.1 21.0 55.8 -34.8 Notes: 1. Peak Detector Data unless otherwise stated. 2. All measurements were made at 3 meter. Harmonic emissions not detected at the 3-meter distance were measured at 0.3-meter and an inverse proportional extrapolation was performed to compare the signal level to the 3-meter limit. No other harmonic emissions than those reported were detected at a test distance of 0.3-meter. 3. Negative value in the margin column shows emission below limit. 4. Horn antenna is used for the emission over 1000MHz. 5. “*” Emission within restricted band fulfil the requirement of Section 15.209. Test Engineer: Mark Cheung FCC ID: QOB45138 12

INTERTEK TESTING SERVICES 3.4 Conducted Emission Configuration Photograph Worst Case Line-Conducted Configuration For electronic filing, the worst case line-conducted configuration photograph are saved with filename: conducted photos.doc. FCC ID: QOB45138 13

INTERTEK TESTING SERVICES 3.5 Conducted Emission Data For electronic filing, the graph and data table of conducted emission is saved with filename: conducted.pdf. Judgement: Passed by at least 20 dB TEST PERSONNEL: Signature Mark Cheung, Compliance Engineer Typed/Printed Name December 31, 2007 Date FCC ID: QOB45138 14

INTERTEK TESTING SERVICES EXHIBIT 4 EQUIPMENT PHOTOGRAPHS FCC ID: QOB45138 15

INTERTEK TESTING SERVICES 4.0 Equipment Photographs For electronic filing, the photographs of the tested EUT are saved with filename: external photos.doc & internal photos.doc. FCC ID: QOB45138 16

INTERTEK TESTING SERVICES EXHIBIT 5 PRODUCT LABELLING FCC ID: QOB45138 17

INTERTEK TESTING SERVICES 5.0 Product Labelling For electronic filing, the FCC ID label artwork and the label location are saved with filename: label.pdf. FCC ID: QOB45138 18

INTERTEK TESTING SERVICES EXHIBIT 6 TECHNICAL SPECIFICATIONS FCC ID: QOB45138 19

INTERTEK TESTING SERVICES 6.0 Technical Specifications For electronic filing, the block diagram and schematics of the tested EUT are saved with filename: block.pdf and circuit.pdf respectively. FCC ID: QOB45138 20

INTERTEK TESTING SERVICES EXHIBIT 7 INSTRUCTION MANUAL FCC ID: QOB45138 21

INTERTEK TESTING SERVICES 7.0 Instruction Manual For electronic filing, a preliminary copy of the Instruction Manual is saved with filename: manual.pdf. This manual will be provided to the end-user with each unit sold/leased in the United States. FCC ID: QOB45138 22

INTERTEK TESTING SERVICES EXHIBIT 8 MISCELLANEOUS INFORMATION FCC ID: QOB45138 23

INTERTEK TESTING SERVICES 8.0 Miscellaneous Information This miscellaneous information includes details of the measured bandwidth, the test procedure and calculation of factors such as pulse desensitization and averaging factor. FCC ID: QOB45138 24

INTERTEK TESTING SERVICES 8.1 Measured Bandwidth For electronic filing, the plot shows the fundamental emission when modulated is saved with filename: bw.pdf. From the plot, the bandwidth is observed to be 540 kHz, at 20 dBc where the bandwidth limit is 795 kHz. Therefore, the unit meets the requirement of section 15.231(c). Figure 8.1 Bandwidth FCC ID: QOB45138 25

INTERTEK TESTING SERVICES 8.2 Discussion of Pulse Desensitization The determination of pulse desensitivity was made in accordance with Hewlett Packard Application Note 150-2, Spectrum Analysis ... Pulsed RF. The effective period (Teff) was approximately 0.24 ms for a digital "1" bit, as shown in the plots of Exhibit 8.3. With a resolution bandwidth (3 dB) of 100 kHz, the pulse desensitivity factor was 0 dB. FCC ID: QOB45138 26

INTERTEK TESTING SERVICES 8.3 Calculation of Average Factor Averaging factor in dB = 20 log (duty cycle) The specification for output field strengths in accordance with the FCC rules specify measurements with an average detector. During testing, a spectrum analyzer incorporating a peak detector was used. Therefore, a reduction factor can be applied to the resultant peak signal level and compared to the limit for measurement instrumentation incorporating an average detector. The time period over which the duty cycle is measured is 100 milliseconds, or the repetition cycle, whichever is a shorter time frame. The worst case (highest percentage on) duty cycle is used for the calculation. The duty cycle is measured by placing the spectrum analyzer in zero scan (receiver mode) and linear mode at maximum bandwidth (3 MHz at 3 dB down) and viewing the resulting time domain signal output from the analyzer on a Tektronix oscilloscope. The oscilloscope is used because of its superior time base and triggering facilities. The duty cycle is simply the on-time divided by the period: The duration of one cycle = 99.0 ms Effective period of the cycle = (1x1.43+7x0.504+20x0.24) ms = 9.758 ms DC = 9.758 ms / 99.0 ms = 0.099 Therefore, the averaging factor is found by 20 log10 0.099 = -20.1 dB For electronic filing, the plot shows the transmission timing is saved with filename: timing.pdf. FCC ID: QOB45138 27

INTERTEK TESTING SERVICES 8.4 Emissions Test Procedures The following is a description of the test procedure used by Intertek Testing Services in the measurements of transmitters operating under Part 15, Subpart C rules. The test set-up and procedures described below are designed to meet the requirements of ANSI C63.4 - 2003. The transmitting equipment under test (EUT) is placed on a wooden turntable which is four feet in diameter and approximately one meter in height above the ground plane. During the radiated emissions test, the turntable is rotated and any cables leaving the EUT are manipulated to find the configuration resulting in maximum emissions. The EUT is adjusted through all three orthogonal axes to obtain maximum emission levels. The antenna height and polarization are varied during the testing to search for maximum signal levels. The height of the antenna is varied from one to four meters. Detector function for radiated emissions is in peak mode. Average readings, when required, are taken by measuring the duty cycle of the equipment under test and subtracting the corresponding amount in dB from the measured peak readings. A detailed description for the calculation of the average factor can be found in Exhibit 8.3. The frequency range scanned is from the lowest radio frequency signal generated in the device which is greater than 9 kHz to the tenth harmonic of the highest fundamental frequency or 40 GHz, whichever is lower. For line conducted emissions, the range scanned is 150 kHz to 30 MHz. FCC ID: QOB45138 28

INTERTEK TESTING SERVICES 8.4 Emissions Test Procedures (cont'd) The EUT is warmed up for 15 minutes prior to the test. AC power to the unit is varied from 85% to 115% nominal and variation in the fundamental emission field strength is recorded. If battery powered, a new, fully charged battery is used. Conducted measurements are made as described in ANSI C63.4 - 2003. The IF bandwidth used for measurement of radiated signal strength was 100 kHz or greater when frequency is below 1000 MHz. Where pulsed transmissions of short enough pulse duration warrant, a greater bandwidth is selected according to the recommendations of Hewlett Packard Application Note 150-2. A discussion of whether pulse desensitivity is applicable to this unit is included in this report (See Exhibit 8.2). Above 1000 MHz, a resolution bandwidth of 1 MHz is used. Transmitter measurements are normally conducted at a measurement distance of three meters. However, to assure low enough noise floor in the forbidden bands and above 1 GHz, signals are acquired at a distance of one meter or less. All measurements are extrapolated to three meters using inverse scaling, unless otherwise reported. Measurements taken at a closer distance are so marked. FCC ID: QOB45138 29


Document Created: 2008-01-14 11:07:27
Document Modified: 2008-01-14 11:07:27
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC