RF Test Report

FCC ID: QOAMC-8250R

Test Report

Download: PDF
FCCID_1877865

FCC TEST REPORT FCC ID: QOAMC-8250R Product： Wireless digital PIR detector Trade Name： Model Name： MC-8250R Serial Model： N/A Report No.： NTEK- 2012NT1214549F Prepared for Shenzhen Meian Technology Co.,Ltd . No.32,Lanshui Rd,Longdong,Longgang District,Shenzhen,China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community,Xixiang Street Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website:www.ntek.org.cn

Page 2 of 31 Report No.: NTEK- 2012NT1214549F TEST RESULT CERTIFICATION Applicant’s name ................. : Shenzhen Meian Technology Co.,Ltd . Address ................................. : No.32,Lanshui Rd,Longdong,Longgang District,Shenzhen,China Manufacture's Name ............ : Shenzhen Meian Technology Co.,Ltd . Address ................................. : No.32,Lanshui Rd,Longdong,Longgang District,Shenzhen,China Product description Product name ........................... : Wireless digital PIR detector Model and/or type reference : MC-8250R Serial Model： N/A Rating(s) ................................ : DC 3V Standards ............................. : FCC Part15.231 Test procedure .............................. ANSI C63.4-2003 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personal only, and shall be noted in the revision of the document. Date of Test ............................................ : Date (s) of performance of tests ............. : 11 Dec 2012 ~16 Dec 2012 Date of Issue ........................................... : 06 Jan 2013 Test Result ............................................... : Pass Testing Engineer : (Apple Huang) Technical Manager : (Tom Zhang) Authorized Signatory : (Bovey Yang) `

Page 3 of 31 Report No.: NTEK- 2012NT1214549F Table of Contents Page 1 . SUMMARY OF TEST RESULTS 4 1.1 TEST FACILITY 5 1.2 MEASUREMENT UNCERTAINTY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST MODES 7 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 8 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 9 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 10 3 . ANTENNA REQUIREMENT 11 3.1 STANDARD REQUIREMENT 11 3.2 EUT ANTENNA 11 3.3 CONDUCTED EMISSION MEASUREMENT 12 3.3.1 POWER LINE CONDUCTED EMISSION LIMITS 12 3.3.2 TEST PROCEDURE 13 3.3.3 DEVIATION FROM TEST STANDARD 13 3.3.4 TEST SETUP 13 3.2.5 TEST RESULT 14 3.4 RADIATED EMISSION MEASUREMENT 15 3.4.1 RADIATED EMISSION LIMITS 15 3.4.2 TEST PROCEDURE 16 3.4.3 DEVIATION FROM TEST STANDARD 16 3.4.4 TEST SETUP 16 3.4.5 TEST RESULTS (BLOW 30MHZ) 18 3.4.6 TEST RESULTS (BETWEEN 30 – 1000 MHZ) 19 4 . BANDWIDTH TEST 23 4.1 TEST PROCEDURE 23 4.2 DEVIATION FROM STANDARD 23 4.3 TEST SETUP 23 4.4 TEST RESULTS 24 5 . TRANSMITTER TIMEOUT 27 5.1 REQUIREMENTS 27 6 . EUT TEST PHOTO 31 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS `

Page 4 of 31 Report No.: NTEK- 2012NT1214549F 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C Standard Test Item Judgment Remark Section 15.207 Conducted Emission N/A Note(1) 15.203 Antenna Requirement Pass 15.231b Radiated Spurious Emission Pass 15.231c Occupied Bandwidth Pass 15.231a(1)(2) Deactivation Time Pass NOTE: (1) ” N/A” denotes test is not applicable in this Test Report. `

Page 5 of 31 Report No.: NTEK- 2012NT1214549F 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add. : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% `

Page 6 of 31 Report No.: NTEK- 2012NT1214549F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Wireless digital PIR detector Trade Name Model Name MC-8250R Serial Model N/A Model Difference N/A The EUT is a Wireless digital PIR detector Product Type Remote Control Operation Frequency: 433.98MHz Modulation Type: FSK Number Of Channel 1CH. Antenna Designation: Build-in ANT Product Description Antenna Gain(Peak) 0.8dBi Output Power: 68.90 dBuV/m @3m(AV Max.) Based on the application, features, or specification exhibited in User's Manual, the EUT is considered as an ITE/Computing Device. More details of EUT technical specification, please refer to the User's Manual. Channel List N/A Adapter N/A Battery DC 3.0V Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Table for Filed Antenna Ant Brand Model Name Antenna Type Connector Gain (dBi) NOTE . 1 N/A N/A Build-in ANT N/A 0.8 Antenna 3 Operation principle: (1).TEST MODE:When the PIR tamper switch or PIR was detected object invasion, the CPU will send data to wireless module. And wireless module send out the data. (2).NORMAL MODE:Every hour a short "supervision" message whose duration 575 msec is emitted about battery information. (3).CODING MODE:When the detector is under operation status,inverse it to make it send an address code to control panel. `

Page 7 of 31 Report No.: NTEK- 2012NT1214549F 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 TX1 Mode 2 TX2 Mode 3 TX3 For Conducted Emission Final Test Mode Description N/A For Radiated Emission Final Test Mode Description Mode 1 TX1 Mode 2 TX2 Mode 3 TX3 Note: (1) The EUT use new battery. (2)” N/A” denotes test is not applicable in this Test Report. TX1 mode is TEST MODE TX2 mode is NORMAL MODE TX3 mode is CODING MODE `

Page 8 of 31 Report No.: NTEK- 2012NT1214549F 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED Radiated Spurious Emission Test E-1 EUT `

Page 9 of 31 Report No.: NTEK- 2012NT1214549F 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Series No. Note Wireless digital PIR E-1 MC-8250R N/A EUT detector Item Shielded Type Ferrite Core Length Note Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column. `

Page 10 of 31 Report No.: NTEK- 2012NT1214549F 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation Test equipment Item Kind of Equipment Manufacturer Type No. Serial No. Calibrated until 1 Spectrum Analyzer Agilent E4407B 160400005 Jul. 06. 2013 2 Test Receiver R&S ESPI 101318 Jul. 06. 2013 3 Bilog Antenna TESEQ CBL6111D 31216 Jul. 06. 2013 4 50Ω Coaxial Switch Anritsu MP59B 6200264416 Jul. 06. 2013 5 Spectrum Analyzer ADVANTEST R3132 150900201 Jul. 06. 2013 6 Horn Antenna EM EM-AH-10180 2011071402 Jul. 06. 2013 7 Horn Ant Schwarzbeck BBHA 9170 9170-181 Jul. 06. 2013 8 Amplifier EM EM-30180 060538 Jul. 06. 2013 9 Loop Antenna ARA PLA-1030/B 1029 Jul. 06. 2013 10 Power Meter R&S NRVS 100696 Jul. 06. 2013 Conduction Test equipment Item Kind of Equipment Manufacturer Type No. Serial No. Calibrated until 1 Test Receiver R&S ESCI 101160 Jul. 06. 2013 2 LISN R&S ENV216 101313 Jul. 06. 2013 3 LISN EMCO 3816/2 00042990 Jul. 06. 2013 4 50Ω Coaxial Switch Anritsu MP59B 6200264417 Jul. 06. 2013 5 Passive Voltage R&S ESH2-Z3 100196 Jul. 06. 2013 Probe 6 Absorbing clamp R&S MOS-21 100423 Jul. 06. 2013 `

Page 11 of 31 Report No.: NTEK- 2012NT1214549F 3. ANTENNA REQUIREMENT 3.1 STANDARD REQUIREMENT 15.203 requirements: For intentional device, according to 15.203: an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 3.2 EUT ANTENNA The EUT antenna is Build-in ANT. It complies with the standard requirement. `

Page 12 of 31 Report No.: NTEK- 2012NT1214549F 3.3 CONDUCTED EMISSION MEASUREMENT 3.3.1 POWER LINE CONDUCTED EMISSION Limits (Frequency Range 150KHz-30MHz) Class A (dBuV) Class B (dBuV) FREQUENCY (MHz) Standard Quasi-peak Average Quasi-peak Average 0.15 -0.5 66 - 56 * 56 - 46 * CISPR 0.50 -5.0 56.00 46.00 CISPR 5.0 -30.0 60.00 50.00 CISPR 0.15 -0.5 66 - 56 * 56 - 46 * LP002. 0.50 -5.0 56.00 46.00 LP002. 5.0 -30.0 60.00 50.00 LP002. Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz `

Page 13 of 31 Report No.: NTEK- 2012NT1214549F 3.3.2 TEST PROCEDURE a. The EUT was placed 0.4 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.3.3 DEVIATION FROM TEST STANDARD No deviation 3.3.4 TEST SETUP V e r tic a l R e fe r e n c e G r o u n d P la n e T e s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n ta l R e f e r e n c e G r o u n d P la n e N o te : 1 .S u p p o r t u n its w e r e c o n n e c te d to s e c o n d L IS N . 2 .B o t h o f L IS N s ( A M N ) a r e 8 0 c m fr o m E U T a n d a t le a s t 8 0 f r o m o th e r u n its a n d o t h e r m e ta l p la n e s `

Page 14 of 31 Report No.: NTEK- 2012NT1214549F 3.2.5 TEST RESULT EUT： Wireless digital PIR detector Model Name. ： MC-8250R Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Phase : L Test Voltage ： N/A Test Mode： N/A Note: It is powered by the battery, Conduction emission test is is not applicable. `

Page 15 of 31 Report No.: NTEK- 2012NT1214549F 3.4 RADIATED EMISSION MEASUREMENT 3.4.1 Radiated Emission Limits ( FCC 15.209 ) Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 Note: (1) The tighter limit applies at the band edges. (2) Emission level (dBuV/m)=20log Emission level (uV/m). LIMITS OF RADIATED EMISSION MEASUREMENT ( FCC 15.231) Field Strength of Field Strength of Unwanted Fundamental Frequency fundamental Emissions (MHz) (microvolts/meter) (microvolts/meter) 40.66 - 40.70 2250.00 225.00 70 - 130 1250.00 125.00 130 - 174 1,250 to 3,750 ** 125 to 375 ** 174 - 260 3750.00 375.00 260 - 470 3,750 to 12,500 ** 375 to 1,250 ** Above 470 12500.00 1250.00 Notes: (1) ** linear interpolations [Where F is the frequency in MHz, the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 130-174 MHz, uV/m at 3 meters = 56.81818(F) - 6136.3636; for the band 260-470 MHz, uV/m at 3 meters = 41.6667(F) - 7083.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level.] The limits on the field strength of the spurious emissions in the above table are based on the fundamental frequency of the intentional radiator. Spurious emissions shall be attenuated to the average (or, alternatively, CISPR quasi-peak) limits shown in this table or to the general limits shown in 93 Section 15.209, whichever limit permits a higher field strength. Spectrum Parameter Setting Attenuation Auto Start Frequency 1000 MHz Stop Frequency 10th carrier harmonic RB / VB (emission in restricted band) 1MHz / 1MHz for Peak `

Page 16 of 31 Report No.: NTEK- 2012NT1214549F Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9kHz~150kHz / RB 200Hz for QP Start ~ Stop Frequency 150kHz~30MHz / RB 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP 3.4.2 TEST PROCEDURE a. The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz. For frequencies above 1GHz, any suitable measuring distance may be used. b. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3m meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. c. The height of the equipment or of the substitution antenna shall be 0.8 m; the height of the test antenna shall vary between 1 m to 4 m. d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported 3.4.3 DEVIATION FROM TEST STANDARD No deviation 3.4.4 TEST SETUP （A）Radiated Emission Test-Up Frequency Below 30MHz `

Page 17 of 31 Report No.: NTEK- 2012NT1214549F （B）Radiated Emission Test-Up Frequency 30MHz~1GHz （C）Radiated Emission Test-Up Frequency Above 1GHz `

Page 18 of 31 Report No.: NTEK- 2012NT1214549F 3.4.5 TEST RESULTS (BLOW 30MHz) EUT： Wireless digital PIR detector Model Name. ： MC-8250R Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.0V Test Mode ： TX Polarization : -- Freq. Reading Limit Margin State (MHz) (dBuV/m) (dBuV/m) (dB) P/F -- -- -- -- PASS -- -- -- -- PASS NOTE: The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. Distance extrapolation factor =20 log (specific distance/test distance)(dB); Limit line = specific limits(dBuv) + distance extrapolation factor. `

Page 19 of 31 Report No.: NTEK- 2012NT1214549F 3.4.6 TEST RESULTS (BETWEEN 30 – 1000 MHZ) EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 26 ℃ Relative Humidity： 53% Pressure： 1020 hPa Test Power ： DC 3.0V Test Mode ： TX1 The duty cycle is simply the on time divided by the period: The duration of one cycle = 73.5ms On time of one signal=0.425ms, DC = 0.425ms*37/73.5= 0.213 Therefore, the average factor is found by 20log0.213 = -13.43dB The duration of one cycle On time and off time of one signal NOTE: The Peak value is less than AV limit already, the Duty Cycle evaluation is not required for mode 2.and 3. `

Page 20 of 31 Report No.: NTEK- 2012NT1214549F EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 20 ℃ Relative Humidity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.0V Test Mode ： TX1 Polarization : Horizontal Average Field Field Frequency Limit(PK) Limit(AV) Factor Strength Strength State dBuV/m dBuV/m MHz dB dBuV/m dBuV/m (PK) (AV) 433.980 -13.43 82.33 68.90 100.82 80.82 pass 869.1301 -13.43 50.58 37.15 80.82 60.82 pass 1737.500 -13.43 52.77 -- 74.00 54.00 pass 2175.000 -13.43 48.23 -- 80.82 60.82 pass -- -- -- -- 74.00 54.00 pass -- -- -- -- 74.00 54.00 pass EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 20 ℃ Relative Humidity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.0V Test Mode ： TX1 Polarization : Vertical Average Field Field Frequency Limit(PK) Limit(AV) Factor Strength Strength State dBuV/m dBuV/m MHz dB dBuV/m dBuV/m (PK) (AV) 433.980 -13.43 79.92 66.49 100.82 80.82 pass 869.1301 -13.43 49.34 35.91 80.82 60.82 pass 1737.500 -13.43 45.84 -- 74.00 54.00 pass 2175.000 -13.43 52.33 -- 80.82 60.82 pass -- -- -- -- 74.00 54.00 pass -- -- -- -- 74.00 54.00 pass `

Page 21 of 31 Report No.: NTEK- 2012NT1214549F EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 20 ℃ Relative Humidity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.0V Test Mode ： TX2 Polarization : Horizontal Average Field Field Frequency Limit(PK) Limit(AV) Factor Strength Strength State dBuV/m dBuV/m MHz dB dBuV/m dBuV/m (PK) (AV) 433.980 -- 69.41 -- 100.82 80.82 pass 869.1301 -- 49.58 -- 80.82 60.82 pass 1737.500 -- 52.77 -- 74.00 54.00 pass 2175.000 -- 48.23 -- 80.82 60.82 pass -- -- -- -- 74.00 54.00 pass -- -- -- -- 74.00 54.00 pass EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 20 ℃ Relative Humidity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.0V Test Mode ： TX2 Polarization : Vertical Average Field Field Frequency Limit(PK) Limit(AV) Factor Strength Strength State dBuV/m dBuV/m MHz dB dBuV/m dBuV/m (PK) (AV) 433.980 -- 68.32 -- 100.82 80.82 pass 869.1301 -- 49.34 -- 80.82 60.82 pass 1737.500 -- 45.84 -- 74.00 54.00 pass 2175.000 -- 52.33 -- 80.82 60.82 pass -- -- -- -- 74.00 54.00 pass -- -- -- -- 74.00 54.00 pass `

Page 22 of 31 Report No.: NTEK- 2012NT1214549F EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 20 ℃ Relative Humidity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.0V Test Mode ： TX3 Polarization : Horizontal Average Field Field Frequency Limit(PK) Limit(AV) Factor Strength Strength State dBuV/m dBuV/m MHz dB dBuV/m dBuV/m (PK) (AV) 433.980 -- 67.41 -- 100.82 80.82 pass 869.1301 -- 48.22 -- 80.82 60.82 pass 1737.500 -- 43.31 -- 74.00 54.00 pass 2175.000 -- 41.22 -- 80.82 60.82 pass -- -- -- -- 74.00 54.00 pass -- -- -- -- 74.00 54.00 pass EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 20 ℃ Relative Humidity： 48% Pressure： 1010 hPa Test Voltage ： DC 3.0V Test Mode ： TX3 Polarization : Vertical Average Field Field Frequency Limit(PK) Limit(AV) Factor Strength Strength State dBuV/m dBuV/m MHz dB dBuV/m dBuV/m (PK) (AV) 433.980 -- 66.67 -- 100.82 80.82 pass 869.1301 -- 49.54 -- 80.82 60.82 pass 1737.500 -- 44.32 -- 74.00 54.00 pass 2175.000 -- 40.12 -- 80.82 60.82 pass -- -- -- -- 74.00 54.00 pass Note: 1. Emissions attenuated more than 20 dB below the permissible value are not reported. 2. FCC Limit for Average Measurement = 41.6667(433.98)-7083.3333 = 10999.1811uV/m =80.82dBuV/m 3. Field Strength(AV) = Field Strength(PK)+Average Factor. 4. The signal bandwidth was measured and less then 100KHz RBW, so PDCF factor is not required.. `

Page 23 of 31 Report No.: NTEK- 2012NT1214549F 4. BANDWIDTH TEST 4.1 TEST PROCEDURE The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. Limit: 433.98MHz*0.25%=1.08MHz 4.2 DEVIATION FROM STANDARD No deviation. 4.3 TEST SETUP `

Page 24 of 31 Report No.: NTEK- 2012NT1214549F 4.4 TEST RESULTS EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 26 ℃ Relative Humidity： 53% Pressure： 1020 hPa Test Power ： DC 3.0V Test Mode ： TX1 Frequency 20 dBc Bandwidth Limit Test Channel (MHz) (MHz) (MHz) CH01 433.98 0.479 1.08 `

Page 25 of 31 Report No.: NTEK- 2012NT1214549F EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 26 ℃ Relative Humidity： 53% Pressure： 1020 hPa Test Power ： DC 3.0V Test Mode ： TX2 Frequency 20 dBc Bandwidth Limit Test Channel (MHz) (MHz) (MHz) CH01 433.98 0.533 1.08 `

Page 26 of 31 Report No.: NTEK- 2012NT1214549F EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 26 ℃ Relative Humidity： 53% Pressure： 1020 hPa Test Power ： DC 3.0V Test Mode ： TX3 Frequency 20 dBc Bandwidth Limit Test Channel (MHz) (MHz) (MHz) CH01 433.98 0.487 1.08 `

Page 27 of 31 Report No.: NTEK- 2012NT1214549F 5. TRANSMITTER TIMEOUT 5.1 REQUIREMENTS 1 47 CFR FCC Part 15 Subpart C, section 15.231(a)/(e): If devices complying with 47 CFR FCC Part 15 Subpart C, section 15.231(a). (1) A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. (2) A transmitter activated automatically shall cease transmission within 5 seconds after activation. (3) Periodic transmissions at regular predetermined intervals are not permitted. However, polling or supervision transmissions, including data, to determine system integrity of transmitters used in security or safety applications are allowed if the total duration of transmissions does not exceed more than two seconds per hour for each transmitter. There is no limit on the number of individual transmissions, provided the total transmission time does not exceed two seconds per hour. (4) Intentional radiators which are employed for radio control purposes during emergencies involving fire, security, and safety of life, when activated to signal an alarm, may operate during the pendency of the alarm condition. (5) Transmission of set-up information for security systems may exceed the transmission duration limits in paragraphs 15.231(a) of this section, provided such transmission are under the control of a professional installer and do not exceed ten seconds after a manually operated switch is released or a transmitter is activated automatically. Such set-up information may include data. If devices complying with 47 CFR FCC Part 15 Subpart C, section 15.231(e) Intentional radiators may operate at a periodic rate exceeding that specified in section 15.231(a) and may be employed for any type of operation, including operation prohibited section 15.231(a). `

Page 28 of 31 Report No.: NTEK- 2012NT1214549F EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 26 ℃ Relative Humidity： 53% Pressure： 1020 hPa Test Power ： DC 3.0V Test Mode ： TX1 Test data THE DURATION OF LIMIT RESULT EACH TRANSMISSION 0.587s <5s PASS A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. `

Page 29 of 31 Report No.: NTEK- 2012NT1214549F EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 26 ℃ Relative Humidity： 53% Pressure： 1020 hPa Test Power ： DC 3.0V Test Mode ： TX2 Test data THE DURATION OF LIMIT RESULT EACH TRANSMISSION 0.575s <5s PASS A transmitter activated automatically shall cease transmission within 5 seconds afteractivation. (Every hour a short "supervision" message whose duration 575 msec is emitted about battery information) `

Page 30 of 31 Report No.: NTEK- 2012NT1214549F EUT： Wireless digital PIR detector Model Name ： MC-8250R Temperature： 26 ℃ Relative Humidity： 53% Pressure： 1020 hPa Test Power ： DC 3.0V Test Mode ： TX3 Test data THE DURATION OF LIMIT RESULT EACH TRANSMISSION 0.562s <5s PASS A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. `

Page 31 of 31 Report No.: NTEK- 2012NT1214549F 6. EUT TEST PHOTO Radiated Measurement Photos `


Document Created: 2013-01-11 09:20:19
Document Modified: 2013-01-11 09:20:19
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC