test report

FCC ID: QLXBSS0134

Test Report

Download: PDF
FCCID_1709720

Test report no. 12007526 Page 1 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 Test Report acc. to FCC Title 47 CFR Part 15 relating to TeraTron GmbH BSS0134 Title 47 - Telecommunication Part 15 - Radio Frequency Devices Subpart C – Intentional Radiators Measurement Procedure: ANSI C63.4-2009 Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 2 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 Manufacturer’s details Manufacturer TeraTron GmbH Manufacturer’s grantee code QLX Manufacturer’s address TeraTron GmbH Bunsenstr. 10 51647 Gummersbach Germany Phone: + 49 (0) 2261 8082-0 Fax: + 49 (0) 2261 8082-99 Email: michael.marquart@teratron.de Relevant standard used 47 CFR Part 15C - Intentional Radiators ANSI C63.4-2009 Test Report prepared by Technical engineer Ralf Trepper m. dudde hochfrequenz-technik (laboratory) Rottland 5a 51429 Bergisch Gladbach Germany Phone: +49 2207 96890 Fax: +49 2207 968920 Email: m.duddelabor@dudde.com Equipment Under Test (EUT) Equipment category Transmitter Trade name TeraTron Type designation BSS0134 Serial no. --- Variants --- Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 3 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 1. Test results Clause Requirements headline Test result Report page number 8.1 Antenna Requirement Pass Fail N.t.* 9 8.2 Field Strength limit (fundamental) Pass Fail N.t.* 12 to 15 8.3 Radiated emission limits Pass Fail N.t.* 16 to 21 8.4 Bandwidth (20 dB) Pass Fail N.t.* 25 to * Not tested The equipment meets the requirements Yes No Signature: ............................. Signature: ............................. (Technician) (Manager) Digital unterschrieben von Andreas Morsbach DN: cn=Andreas Morsbach, o=m.dudde hf-technik, ou=Management, email=m.duddeconsult @dudde.com, c=DE Datum: 2012.04.04 10:03:26 +02'00' Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 4 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 Table of contents 1. Test results ........................................................................................................................................................ 3 2. Introduction ...................................................................................................................................................... 5 3. Testing laboratory ............................................................................................................................................ 5 4. Applicant .......................................................................................................................................................... 6 5. Product and product documentation ................................................................................................................ 6 6. Conclusions, observations and comments........................................................................................................ 7 7. Operational description...................................................................................................................................... 8 8. Compliance assessment ..................................................................................................................................... 9 8.1 Antenna requirement ....................................................................................................................................... 9 8.1.2 Result .................................................................................................................................................... 9 8.2 Fundamental frequencies / Field strength limits ............................................................................................ 10 8.2.1 Regulation ............................................................................................................................................. 10 8.2.2 Test equipment ...................................................................................................................................... 11 8.2.3 Test procedure....................................................................................................................................... 12 8.2.4 Calculation of the average correction factor ......................................................................................... 13 8.2.5 Calculation of the field strengths .......................................................................................................... 13 8.2.7 Result .................................................................................................................................................... 14 8.3 Radiated emission limits ................................................................................................................................ 15 8.3.1 Result .................................................................................................................................................... 16 8.4 Bandwidth (20 dB) ......................................................................................................................................... 17 8.4.1 Test equipment ...................................................................................................................................... 17 8.4.2 Test procedure....................................................................................................................................... 18 8.4.3 20 dB bandwidth limit .......................................................................................................................... 18 8.4.4 Result .................................................................................................................................................... 18 9. Additional information to the test report.......................................................................................................... 19 Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 5 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 2. Introduction This test report consists of:  Test result summary  List of contents  Introduction and further information  Performance assessment  Detailed test information All pages have been numbered consecutively and bear the m. dudde hochfrequenz-technik logo, the test report number, the date, the test specification in its current version as well as the type designation of the EUT. The total number of pages in this report is 20. The tests were carried out at: - m. dudde hochfrequenz-technik, D-51429 Bergisch Gladbach in a representative assembly and in accordance with the test methods and/or requirements stated in: FCC Title 47 CFR Part 15 Subpart C & ANSI C63.4-2009 The sample of the product was received on: - 2011-10-19 The tests were carried out in the following period of time: - 2011-10-19 – 2012-01-17 3. Testing laboratory m. dudde hochfrequenz-technik Rottland 5a, 51429 Bergisch Gladbach, Germany Phone: +49 - (0) 22 07 / 96 89-0 Fax: +49 - (0) 22 07 / 96 89-20 - FCC Registration Number: 699717 Accredited by: DAkkS Deutsche Akkreditierungsstelle GmbH DAkkS accreditation number: D-PL-12053-01 Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 6 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 4. Applicant Company name : TeraTron GmbH Address : Bunsenstr. 10 51647 Gummersbach Country : Germany Telephone : + 49 (0) 2261 8082-0 Fax : + 49 (0) 2261 8082-99 Email : michael.marquart@teratron.de Date of order : 2011-09-20 References : Mr. Michael Marquart 5. Product and product documentation Samples of the following apparatus were submitted for testing: Manufacturer : Tera ron GmbH Trademark : TeraTron Type designation : BSS0134 Hardware version : BSS0134 Serial number : --- Software release : --- Type of equipment : transmitter Power used : 3.6 V DC Frequency used : 916.600 MHz Generated frequencies : 16.000 MHz (Crystal), 916.600 MHz (Carrier) ITU emission class : 67K9 A1D FCC ID : QLXBSS0134 Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 7 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 For issuing this report the following product documentation was used: Description Date Identifications External photographs of the Equipment Under Test (EUT) 2012-03-26 Annex no. 1 Internal photographs of the Equipment Under Test (EUT) 2012-03-26 Annex no. 2 Channel occupancy / bandwidth 2012-03-26 Annex no. 3 Label sample 2012-03-26 Annex no. 4 Functional description / User manual 2012-03-26 Annex no. 5 Test setup photos 2012-03-26 Annex no. 6 Block diagram 2012-03-26 Annex no. 7 Operational description 2012-03-26 Annex no. 8 Schematics 2012-03-26 Annex no. 9 Parts list 2012-03-26 Annex no. 10 6. Conclusions, observations and comments The test report will be filed at m. dudde hochfrequenz-technik for a period of 10 years following the issue of this report. It may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of m. dudde hochfrequenz-technik. The results of the tests as stated in this report are exclusively applicable to the EUT as identified in this report. m. dudde hochfrequenz-technik cannot be held liable for properties of the EUT that have not been observed during these tests. m. dudde hochfrequenz-technik assumes the sample to comply with the requirements of FCC Title 47 CFR Part 15 for the respective test sector, if the test results turn out positive. Comments: --- Date : 2012-03-26 Date : 2012-03-26 Name : Ralf Trepper Name : Manfried Dudde Function : Technician Function : Manager Signature : …………………. Signature : ………………… Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 8 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 7. Operational description 7.1 EUT details RF- Transmitter, protective field system for self-propelled BOMAG multipurpose compactors, based on active transponder technology 7.2 EUT configuration After connection with a power supply the Protective field system RF transmitter begins to run. 7.3 EUT measurement description The Protective field system RF transmitter was tested in a typical fashion. During preliminary emission tests the Protective field system RF transmitter was operated in continuous transmitting mode for worst case emission mode investigation. Therefore, the final qualification testing was completed with Protective field system RF transmitter operated in continuous modes. All tests were performed with the applicant’s typical voltage: 3.6 V DC In order to establish the maximum radiation, firstly, there have been viewed all orthogonal adjustments of the test samples, secondly the test ample have been rotated at all adjustments around the own axis between 0° and 360°, and thirdly, the antenna polarization between horizontal and vertical had been varied. Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 9 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8. Compliance assessment 8.1 Antenna requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not exceeded. 8.1.2 Result The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Page no. Loop antenna as part on the PCB! N.t.* See page no. 19 Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 10 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8.2 Fundamental frequencies / Field strength limits 8.2.1 Regulation Test requirement: FCC CFR47, Part 15C Section 15.249 Test procedure: ANSI C63.4:2009 (a) Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: (d) Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in §15.209, whichever is the lesser attenuation. (e) As shown in §15.35(b), for frequencies above 1000 MHz, the field strength limits in paragraphs (a) and (b) of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For point-to-point operation under paragraph (b) of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. (f) Parties considering the manufacture, importation, marketing or operation of equipment under this section should also note the requirement in §15.37(d). Field strength Field strength of fundamental Fundamental frequency of spurious emissions (µV/m) (µV/m) 902-928 MHz 50 500 2400-2483.5 MHz 50 500 5725-5875 MHz 50 500 24.0-24.25 GHz 250 2500 (1) The above field strength limits are specified at a distance of 3 meters. The tighter limits apply at the band edges. (2) Intentional radiators operating under the provisions of this Section shall demonstrate compliance with the limits on the field strength of emissions, as shown in the above table, based on the average value of the measured emissions. As an alternative, compliance with the limits in the above table may be based on the use of measurement instrumentation with a CISPR quasi-peak detector. The specific method of measurement employed shall be specified in the application for equipment authorization. If average emission measurements are employed, the provisions in Section 15.35 for averaging pulsed emissions and for limiting peak emissions apply. Further, compliance with the provisions of Section 15.205 shall be demonstrated using the measurement instrumentation specified in that section. (3) The limits on the field strength of the spurious emissions in the above table are based on the fundamental frequency of the intentional radiator. Spurious emissions shall be attenuated to the average (or, alternatively, CISPR quasi-peak) limits shown in this table or to the general limits shown in Section 15.209, whichever limit permits higher field strength. Section 15.33 Frequency range of radiated measurements: (a) Unless otherwise noted in the specific rule section under which the equipment operates for an intentional radiator the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 kHz, up to at least the frequency shown in this paragraph: (1) If the intentional radiator operates below 10 GHz: to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 11 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8.2.2 Test equipment Manufacturer/ Last Next Calibration Type Serial no. Model no. calibration calibration executed by OATS Dudde (104) --- 08/2010 08/2012 Dudde Digital Multimeter GW GDM-8045G (144) 0090256 08/2011 08/2014 Dudde Rohde & Schwarz Receiver Rohde & Spectrum Analyzer 100.117 11/2010 11/2012 (9 kHz –18.0 GHz) Schwarz FSL 18 (171a) Pre-amplifier Hewlett Packard 1726A00705 01/2012 01/2014 Dudde (100kHz - 1.3GHz) 8447 E (166a) Pre-amplifier Schwarzbeck 9718-151 03/2011 03/2013 Dudde (0.5GHz - 18GHz) (444) Bilog antenna Schwarzbeck --- 04/2011 04/2014 Schwarzbeck (30- 1000 MHz) VULP 9168 (406) Magnetic loop antenna Schwarzbeck --- 05/2010 05/2013 Dudde (9 kHz - 30 MHz) FMZB 1516 (23) Log antenna Schwarzbeck --- 09/2009 09/2012 Schwazbeck (1- 18 GHz) STLP 9148 (445) Horn antenna BBHA 9120 A (284) 236 03/2011 03/2013 Dudde (0.86-8.5 GHz) Horn antenna Schwarzbeck 305 03/2012 03/2014 Dudde (2.0-14.0 GHz) BBHA 9120 C (169) RF- cable Kabelmetal 18m [N] K1 09/2011 09/2012 Dudde RF- cable Aircell 0.5m [BNC] K40 09/2011 09/2012 Dudde Sucoflex 100 Suhner RF- cable K52 09/2011 09/2012 Dudde 1 m [N] RF- cable Aircell 1m [BNC/N] K56 09/2011 09/2012 Dudde Sucoflex 106 Suhner 6,4m RF- cable K74 09/2011 09/2012 Dudde [N] Sucoflex 106 Suhner 6,4m RF- cable K75 09/2011 09/2012 Dudde [N] Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 12 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8.2.3 Test procedure The EUT and this peripheral (when additional equipment exists) are placed on a turn table which is 0.8m above the ground. The turn table would be allowed to rotate 360 degrees to determine the position of the maximum emission level. The test distance between the EUT and the receiving antenna are 3m. To find the maximum emission, the polarization of the receiving antenna are changed in horizontal and vertical polarization, the position of the EUT was changed in different orthogonal determinations. ANSI C63.4: 2009 Section 8 “Radiated emission measurements” Measurement procedures for electric field radiated emissions above 1 GHz are covered in Clause 8 of ANSI C63.4- 2009. The C63.4-2009 measurement procedure consists of both an exploratory test and a final measurement. The exploratory test is critical to determine the frequency of all significant emissions. For each mode of operation required to be tested, the frequency spectrum is monitored. Variations in antenna height, antenna orientation, antenna polarization, EUT azimuth, and cable or wire placement is explored to produce the emission that has the highest amplitude relative to the limit. The final measurements are made based on the findings in the exploratory testing. When making exploratory and final measurements it is necessary to maximize the measured radiated emission. Subclause 8.3.1.2 of C63.4-2009 states that the measurement is to be made “while keeping the antenna in the ‘cone of radiation’ from that area and pointed at the area both in azimuth and elevation, with polarization oriented for maximum response.” We consider the “cone of radiation” to be the 3 dB beamwidth of the measurement antenna. While the “bore-sighting” technique is not explicitly mentioned in C63.4-2009, it is a useful technique for measurements using a directional antenna, such as a double-ridged waveguide antenna. Several precautions must be observed, including: knowledge of the beamwidth of the antenna and the resulting illumination area relative to the size of the EUT, estimation for source of the emission and general location within larger EUTS, measuring system sensitivity, etc. C63.4-2009 requires that the measurement antenna is kept pointed at the source of the emission both in azimuth and elevation, with the polarization of the antenna oriented for maximum response. That means that if the directional radiation pattern of the EUT results in a maximum emission at an upwards angle from the EUT, when a directional antenna is used to make the measurement it will be necessary for it to be pointed towards the source of the emission within the EUT. This can be done by either pointing the antenna at an angle towards the source of the emission, or by rotating the EUT, in both height and polarization, to maximize the measured emission. The emission must be kept within the illumination area of the 3 dB beamwidth of the antenna so that the maximum emission from the EUT is measured. Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 13 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 Radiated emissions test characteristics Frequency range 30 MHz - 12,000 MHz Test distance 10m, 3 m* Test instrumentation resolution bandwidth 9 kHz (20 kHz – 30 MHz) 120 kHz (30 MHz - 1,000 MHz) 1 MHz (1000 MHz - 12,000 MHz) Receive antenna height 1 m (20 kHz – 30 MHz) Receive antenna polarization 0° - 90° (20 kHz – 30 MHz) Receive antenna scan height 1 m - 4 m (30 MHz - 12,000 MHz) Receive antenna polarization vertical/horizontal (30 MHz - 12,000 MHz) *According to Section 15.31 (f) (1): At frequencies at or above 30 MHz, measurements may be performed at a distance other than what is specified provided: measurements are not made in the near field except where it can be shown that near field measurements are appropriate due to the characteristics of the device; and it can be demonstrated that the signal levels needed to be measured at the distance employed can be detected by the measurement equipment. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor of 20dB/decade (inverse linear-distance for field strength measurements; inverse-linear-distance-squared for power density measurements). 8.2.4 Calculation of the average correction factor The average correction factor is computed by analyzing the "worst case" on time in any 100msec time period and using the formula: Corrections Factor + 20*log (worst case on time/100msec). Analysis of the remote transmitter worst case on time in any 100msec time period is an on time of 50msec, therefore the correction factor is 20*log (50/100) = - 6 dB. The maximum correction factor to be applied is 20 dB per section 15.35 of the FCC rules. 8.2.5 Calculation of the field strengths The field strength is calculated by the following calculation: Corrected Level = Receiver Level + Correction Factor (without the use of a pre-amplifier) Corrected Level = Receiver Level + Correction Factor – Pre-Amplifier (with the use of a pre-amplifier) Receiver Level : Receiver reading without correction factors Correction Factor : Antenna factor + cable loss For example: The receiver reading is 32.7 dBµV. The antenna factor for the measured frequency is +2.5 dB (1/m) and the cable factor for the measured frequency is 0.71 dB, giving a field strength of 35.91dBµV/m. The 35.91dBµV/m value can be mathematically converted to its corresponding level in µV/m. Level in µV/m = Common Antilogarithm (35.91/20) = 39.8 For test distance other than what is specified, but fulfilling the requirements of Section 15.31 (f) (1) the field strength is calculated by adding additionally an extrapolation factor of 20 dB/decade (inverse linear distance for field strength measurements). Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 14 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8.2.7 Result TRANSMITTER SPURIOUS RADIATION (Section 15.249) Polarisation Antenna f Bandwidth Noted Test Correction Averaging Level Limit Margin EUT height (MHz) (kHz) / Type receiver distance factor correction corrected Average / of detector level Factor *7 antenna m dB dB dBµV/m dBµV/m dBµV/m cm dBµV 916.600 1000, QPK 84.3 3 +5.1 0 89.4 94.0 4.6 H, 270° / V 104 6 1833.200 1000, AV 52.1 3 -7.7* 0 44.4 54.0 9.6 H, 270° / V 184 6 2749.800 1000, AV 50.1 3 -3.5* 0 46.6 54.0 7.4 H, 120° / V 119 6 3666.400 1000, AV ≤ 10.0 3 +1.2* 0 11.2 54.0 42.8 H,V /H,V 100-400 6 4583.000 1000, AV ≤ 10.0 3 +3.9* 0 13.9 54.0 40.1 H,V /H,V 100-400 6 5499.600 1000, AV ≤ 10.0 3 +7.6* 0 17.6 54.0 36.4 H,V /H,V 100-400 6 6416.200 1000, AV ≤ 14.0 3 +10.1* 0 24.1 54.0 29.9 H,V /H,V 100-400 6 7332.800 1000, AV ≤ 14.0 3 +16.1* 0 30.1 54.0 23.9 H,V /H,V 100-400 6 8249.400 1000, AV ≤ 14.0 3 +17.0* 0 31.0 54.0 23.0 H,V /H,V 100-400 6 9166.000 1000, AV ≤ 14.0 3 +17.2* 0 31.2 54.0 22.8 H,V /H,V 100-400 6 10082.600 1000, AV ≤ 14.0 3 +18.8* 0 32.8 54.0 21.2 H,V /H,V 100-400 Measurement uncertainty 4 dB Blue marked: restricted bands Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *5 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *6 for using a pre-amplifier in the range between 1.0 GHz and 18.0 GHz Remark: *7 for periodic operated transmitter The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Remark: *7 AVERAGE FACTOR CALCULATION (Standard 47 CFR Part 15C (periodic intentional transmitter) N.t.* See page no. 19 Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 15 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8.3 Radiated emission limits Test requirement: FCC CFR47, Part 15C Section 15.209 Test procedure: ANSI C63.4:2009 Section 15.209 (a) except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field strength Measurement distance (MHz) (µV/m) (m) 0.009 - 0.490 2400/F(kHz) 300 0.490 - 1.705 24000/F(kHz) 30 1.705 - 30.0 30 30 30 - 88 100 3 88 - 216 150 3 216 - 960 200 3 Above 960 500 3 (b) In the emission table above, the tighter limit applies at the band edges. (c) The level of any unwanted emissions from an intentional radiator operating under these general provisions shall not exceed the level of the fundamental emission. For intentional radiators which operate under the provisions of other sections within this part and which are required to reduce their unwanted emissions to the limits specified in this table, the limits in this table are based on the frequency of the unwanted emission and not the fundamental frequency. However, the level of any unwanted emissions shall not exceed the level of the fundamental frequency. (d) The emission limits shown in the above table are based on measurements employing a CISPR quasi peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. (e) The provisions in §§ 15.31, 15.33, and 15.35 for measuring emissions at distances other than the distances specified in the above table, determining the frequency range over which radiated emissions are to be measured, and limiting peak emissions apply to all devices operated under this part. (f) In accordance with Section 15.33(a), in some cases the emissions from an intentional radiator must be measured to beyond the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator because of the incorporation of a digital device. lf measurements above the tenth harmonic are so required, the radiated emissions above the tenth harmonic shall comply with the general radiated emission limits applicable to the incorporated digital device, as shown in Section 15.109 and as based on the frequency of the emission being measured, or, except for emissions contained in the restricted frequency bands shown in Section 15.205, the limit on spurious emissions specified for the intentional radiator, whichever is the higher limit. Emissions which must be measured above the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator and which fall within the restricted bands shall comply with the general radiated emission limits in Section 15.109 that are applicable to the incorporated digital device. Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 16 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8.3.1 Result TRANSMITTER SPURIOUS RADIATION (Section 15.205, 15.209) Polarisation f Bandwidth Noted Test Correction Distance Level Limit Margin EUT (MHz) (kHz) receiver level distance factor extrapol. corrected / Type factor antenna of detector dBµV m dB dB dBµV/m dBµV/m dBµV/m orientation 0.1200 0.2, QPK < 4.0 10 20.2 -59.1 -34.9 26.0 @ 300 m 80.90 V, H/0-360° 0.5000 0.2, QPK < 4.0 10 20.2 -19.1 5.1 33.6 @ 30 m 28.5 V, H/0-360° 1.5000 0.2, QPK < 4.0 10 20.2 -19.1 5.1 24.1 @ 30 m 19.00 V, H/0-360° 3.0000 9, QPK < 4.0 10 20.2 -19.1 5.1 29.5 @ 30 m 24.4 V, H/0-360° 5.0000 9, QPK < 4.0 10 20.2 -19.1 5.1 29.5 @ 30 m 24.4 V, H/0-360° 8.0000 9, QPK < 4.0 10 20.2 -19.1 5.1 29.5 @ 30 m 24.4 V, H/0-360° 10.0000 9, QPK < 4.0 10 20.2 -19.1 5.1 29.5 @ 30 m 24.4 V, H/0-360° 20.0000 9, QPK < 4.0 10 20.2 -19.1 5.1 29.5 @ 30 m 24.4 V, H/0-360° 30.0000 9, QPK < 4.0 10 20.2 -19.1 5.1 29.5 @ 30 m 24.4 V, H/0-360° 100, QPK 6 35.0000 ≤ 3.5 3 -3.1* 0 0.4 40.0 36.6 H,V/H,V 6 88.0000 100, QPK ≤ 3.5 3 -10.8* 0 -7.3 40.0 47.3 H,V/H,V 6 216.0000 100, QPK ≤ 3.5 3 -10.3* 0 -6.8 43.5 50.3 H,V/H,V 6 960.0000 100, QPK ≤ 3.5 3 8.5* 0 12.0 43.5 31.5 H,V/H,V 7 1700.0000 1000, AV ≤ 4.5 3 -7.7* 0 -3.2 54.0 57.2 H,V/H,V 7 2250.0000 1000, AV ≤ 10 3 -5.2* 0 4.8 54.0 49.2 H,V/H,V 7 4000.0000 1000, AV ≤ 10 3 3.3* 0 13.3 54.0 40.7 H,V/H,V 7 5000.0000 1000, AV ≤ 10 3 5.5* 0 15.5 54.0 38.5 H,V/H,V 7 7500.0000 1000, AV ≤ 14 3 15.0* 0 29.0 54.0 25.0 H,V/H,V 7 10000.0000 1000, AV ≤ 14 3 18.8* 0 32.8 54.0 21.2 H,V/H,V * All other emissions than harmonics are lower than the noise level of the measuring equipment! Measurement uncertainty 4 dB Blue marked: restricted bands Bandwidth = the measuring receiver bandwidth Remark: *1 noise floor noise level of the measuring instrument ≤ 4.0dBµV @ 10m distance (0.009 MHz –30 MHz) Remark: *2 noise floor noise level of the measuring instrument ≤ 3.5dBµV @ 3m distance (30 – 1,000 MHz) Remark: *3 noise floor noise level of the measuring instrument ≤ 4.5dBµV @ 3m distance (1,000 – 2,000 MHz) Remark: *4 noise floor noise level of the measuring instrument ≤ 10dBµV @ 3m distance (2,000 – 5,500 MHz) Remark: *5 noise floor noise level of the measuring instrument ≤ 14dBµV @ 3m distance (5,500 – 14,500 MHz) Remark: *6 for using a pre-amplifier in the range between 100 kHz and 1,000 MHz Remark: *7 for using a pre-amplifier in the range between 1.0 GHz and 18.0 GHz The equipment meets the requirements Yes* No N.t. Further test results are attached Yes No Page no. N.t.* See page no. 19 Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 17 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8.4 Bandwidth (20 dB) (c) Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §§15.217 through 15.257 and in Subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. The requirement to contain the designated bandwidth of the emission within the specified frequency band includes the effects from frequency sweeping, frequency hopping and other modulation techniques that may be employed as well as the frequency stability of the transmitter over expected variations in temperature and supply voltage. If a frequency stability is not specified in the regulations, it is recommended that the fundamental emission be kept within at least the central 80% of the permitted band in order to minimize the possibility of out-of-band operation. 8.4.1 Test equipment Manufacturer/ Last Next Calibration Type Serial no. Model no. calibration calibration executed by Rohde & Schwarz Receiver Rohde & Signal Analyzer 100.932 2012/02 2014/02 (9 kHz –30.0 GHz) Schwarz FSV 30 (502) Marconi Instruments signal generator Rohde & Low noise signal generator 119347/003 2012/01 2014/01 (10 kHz –5.4 GHz) Schwarz 2042 (6) Hewlett & Packard Frequency counter Rohde & 5351A Microwave frequency 2432A00054 2011/09 2014/09 (10MHz -26.5GHz) Schwarz counter (130) Hewlett Packard Frequency Counter 3049A01217 2011/08 2013/08 DKD 5351B (432) Sucoflex 104 P Suhner 2,13m RF- cable K17a 2012/01 2013/01 Dudde [APC 3.5] Sucoflex 104 P Suhner 2,13m RF- cable K18a 2011/09 2012/09 Dudde [APC 3.5] Test fixture Dudde --- 2011/09 2012/09 Dudde Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 18 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 8.4.2 Test procedure ANSI C63.4-2009 Section 13.1.7 Occupied bandwidth measurements. The bandwidth is measured at an amplitude level reduced from the reference level by a specified ratio. The reference level is the level of the highest amplitude signal observed from the transmitter at either the fundamental frequency or first-order modulation products in all typical modes of operation, including the unmodulated carrier, even if atypical. Once the reference level is established, the equipment is conditioned with typical modulating signals to produce worst-case (i.e., the widest) bandwidth. In order to measure the modulated signal properly, a resolution bandwidth that is small compared to the bandwidth required by the procuring or regulatory agency shall be used on the measuring instrument. However, the 6 dB resolution bandwidth of the measuring instrument shall be set to a value greater than 5 % of the bandwidth requirements. 8.4.3 20 dB bandwidth limit The 20 dB bandwidth limit = 500 kHz 8.4.4 Result The measured 20 dB bandwidth is: 67.9 kHz The equipment meets the requirements Yes No N.t. Further test results are attached Yes No Annex No. 3 N.t.* See page no. 19 Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 19 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 9. Additional information to the test report Remarks N.t.1 Not tested, because the antenna is part of the PCB N.t.2 Not tested, because the EUT is directly battery powered N.t.3 Not tested, because not applicable to the EUT N.t.4 Not tested, because not ordered Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920

Test report no. 12007526 Page 20 of 20 EUT: BSS0134 Date of issue: 2012-03-26 FCC ID: QLXBSS0134 End of test report Date: 2011-09-15 Vers. no. 2.11 m. dudde hochfrequenz-technik Rottland 5a D-51429 Bergisch Gladbach/ Germany Tel: +49 2207-96890 Fax +49 2207-968920


Document Created: 2012-04-04 10:03:26
Document Modified: 2012-04-04 10:03:26
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC