RF Exposure report

FCC ID: QLE-GKM562R

RF Exposure Info

Download: PDF
FCCID_3303339

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QLE-GKM562R Report No.: LCS1612223064E FCC RF Exposure Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Portable Device Refer Standard: KDB 447498 D01 General RF Exposure Guidance v06 FCC Part 2 §2.1093 Evaluation method According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. Conducted Power Results Peak Conducted Output Power Mode Channel Frequency(MHz) (dBm) 01 2407 0.133 GFSK 09 2440 -0.553 16 2477 -1.416 Manufacturing tolerance GFSK (Peak) Channel Channel 01 Channel 09 Channel 16 Target (dBm) -0.5 -0.5 -0.5 Tolerance ±(dB) 1.0 1.0 1.0 ___________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 2

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QLE-GKM562R Report No.: LCS1612223064E Evaluation Results Antenna RF output power SAR Test Exclusion SAR Test Band/Mode f (GHz) Distance (including tune-up tolerance) Threshold Exclusion (mm) dBm mW 2.407 5 0.5 1.1220 0.3482<3.0 Yes GFSK 2.440 5 0.5 1.1220 0.3505<3.0 Yes 2.477 5 0.5 1.1220 0.3532<3.0 Yes Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1093for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. .......................THE END OF REPORT......................... ___________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 2


Document Created: 2017-02-25 09:09:01
Document Modified: 2017-02-25 09:09:01
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC