Manual

FCC ID: QKPFC2710

Users Manual

Download: PDF
FCCID_266041

2B586-226E PERSONAL COMPUTER FC2710 USER’S MANUAL (2B586-226E)

2B586-226E Contents 1. FCC NOTICE ……………………………………….. P. 1 2. Introduction ……………………………………….. P. 2 3. For Your Safety ……………………………………….. P. 3, 4 4. Name of Each Part ……………………………………….. P. 5 4-1 Front Panel ……………………………………….. P. 5 4-2 Rear Panel ……………………………………….. P. 6 5. Cable Hook-ups ……………………………………….. P. 7

2B586-226E 1. FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -1-

2B586-226E 2. Introduction This PC is designed for a data processing unit of automated biochemical analyzer. Use for other purpose, alteration of hardware and BIOS setting and installation of other software are strictly prohibited. -2-

2B586-226E 3. For Your Safety Please note the following items for your safety. ！ Danger The following items show the possibility of human death or serious injury. ・ Do not open the power supply cover inside the PC. It is dangerous because some parts have high voltages. ・ Do not alter the PC. It may result in a fire or an electric shock. ・ Do not exceed the indicated ratings of input voltage. ・ Use only the accessory power cord supplied with the PC. Do not use the accessory power cord for other equipment. It may cause a fire or an electric shock. ・ Keep liquids away from the power switch or other control parts. Moisture may damage these parts and result in electric danger. ・ Do not pull out or insert the power plug by wet hands. It may cause an electric shock. ・ Do not damage, break or fabricate the power plug. Putting a heavy weight on it, pulling it or bending it forcedly may break it and result in a fire or an electric shock. ・ Should heat, smoke, smell generation or other abnormalities be observed, contact a service engineer after turning off the PC immediately and pulling out the power plug. It may result in a fire or an electric shock. ・ Should something (a piece of metal, water or liquids) go inside the PC, contact a service engineer after turning off the PC immediately and pulling out the power plug. It may result in a fire or an electric shock. ・ Battery A lithium battery is used on the motherboard and a nickel-cadmium battery is used on the expansion board. There is danger of explosion if these batteries are incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. Following items are strictly prohibited. −Soaking the battery in water −Heating or incineration over 100 degrees centigrade −Decomposition or charge -3-

2B586-226E ！ Caution The following items show the possibility of human injury or material damage. ・ Do not pull the power cord when you pull out the power plug. It may damage the cord and result in a fire or an electric shock. (Be sure to pull out the plug after holding it in a hand.) ・ Do not install the PC in a humid or dusty place. It may result in a fire or an electric shock. ・ Do not block the vent holes. If they are blocked, the temperature inside will rise and a fire may occur. ・ Avoid an unexpected injury when you lift, relocate or move the PC. If it is too heavy for you, ask someone for help. -4-

2B586-226E 4. Name of Each Part 4-1 Front Panel ①Power Switch ②Floppy Disk Drive Activity LED ⑧Vent Holes ⑦Reset Button ⑤Power Indicator ③3.5” Floppy Disk Drive ⑥Hard Disk Drive Activity LED ④Floppy Disk Eject Button ①Power Switch Pressing this switch turns the PC on and off alternately. The PC is set so as to turn on when it is connected to the AC power without pressing this switch. ②Floppy Disk Drive Activity LED Indicates when the floppy disk drive is being accessed. ③3.5” Floppy Disk Drive A 3.5” floppy disk can be inserted. ④Floppy Disk Eject Button Enables you to take a floppy disk out of the floppy disk drive. ⑤Power Indicator Indicates when the power is on. ⑥Hard Disk Drive Activity LED Indicates when the hard disk drive is being accessed. ⑦Reset Button The PC is reset when this button is pressed. ⑧Vent Holes To take in cool air from the outside. -5-

2B586-226E 4-2 Rear Panel ①Power Input Connector ②Cooling Fan ③Speaker Volume Control ④GPIB Connector ⑩Mouse Connector ⑨Keyboard ⑧Serial Port ⑥Serial Port ⑤Video Connector Connector Connector2 Connector1 ⑦Parallel Port Connector ①Power Input Connector Is connected to the AC power cord. ②Cooling Fan Generates airflow to cool the inside. ③Speaker Volume Control Enables you to adjust the sound level from the speaker on the inside front panel. ④GPIB Connector Is connected to the GPIB signal cable. ⑤Video Connector Is connected to the video signal cable from the monitor. ⑥Serial Port Connector1 Enables you to connect the communication signal cable from a host computer. (Optional) ⑦Parallel Port Connector Enables you to connect a Centronics-compatible parallel printer. ⑧Serial Port Connector2 Is connected to the signal cable from the touch screen on the monitor. ⑨Keyboard Connector Is connected to the keyboard. ⑩Mouse Connector Is not used. ⑪Voltage Selector Switch Sliding switch that selects the input voltage. The settings are 115V or 230V. -6-

2B586-226E 5. Cable Hook-ups Following are how to hook up cables on the rear panel. Monitor AC Power Line RGB Signal Cable PC Touch Screen GPIB Signal LPT Cable Video GPIB Signal Cable COM2 COM1 Keyboard Printer Keyboard AC Power Line AC Power Line Analyzer Unit Relocatable Power Taps -7-


Document Created: 2019-09-04 22:40:43
Document Modified: 2019-09-04 22:40:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC