Test Report SAR Calibration Part 10

FCC ID: QISVOG-L0J

RF Exposure Info

Download: PDF
FCCID_4250750

Measurement Conditions DASY system configuration, as far as not iven on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2600 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.0 1.96 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 37.4 +# 6 % 2.01 mho/m + 6 % Head TSL temperature change during test <0.5 °C =——— =——— SAR result with Head TSL SAR averaged over 1 cm*° (1 g) of Head TSL Condition SAR measured 250 mW input power 14.4 W/kg SAR for nominal Head TSL parameters normalized to 1W 56.4 W/ikg + 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.39 W/kg SAR for nominal Head TSL parameters normalized to 1W 25.2 Wikg + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.5 2.16 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 51.2 +6 % 2.18 mho/m + 6 % Body TSL temperature change during test «0.5 °C SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 13.9 W/kg SAR for nominal Body TSL parameters normalized to 1W 55.1 W/kg + 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 6.17 W/kg SAR for nominal Body TSL parameters normalized to 1W 24.5 Wikg + 16.5 % (k=2) Certificate No: D2600V2—1032_Sep18 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 49.9 0 — 5.0 |Q Return Loss — 26.0 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 46.0 O — 3.5 |Q Return Loss — 25.1 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.153 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on March 03, 2009 Certificate No: D2600V2—1032_Sep18 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 17.09.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN:1032 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.01 S/m; & = 37.4; p = 1000 kg/m> Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.7, 7.7, 7.7) @ 2600 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 e DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 119.6 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 29.4 W/kg SAR(1 g) = 14.4 W/kg; SAR(10 g) = 6.39 W/kg Maximum value of SAR (measured) = 24.1 W/kg dB 9 — 5.20 —10.40 —15.60 —20.80 —26.00 0 dB = 24.1 W/kg = 13.82 dBW/kg Certificate No: D26OO0V2—1032_Sep18 Page 5 of 8

Impedance Measurement Plot for Head TSL File YView Channel Sweep Calibration Trace Scale Marker System Window Help 2 600000 GHz 49.949 0) 12.269 pF —4.9893 0 2600000 GHz 49.859 mU —87. 723 ® Ch1Avg= 20 * | Ch1: Start 2.40000 GHza —— Stop 2.90000 GHz 0.00 2 §00000 GHz —2§ 045 dB 10.00 15.00 20.00 5.00 30.00 35.00 0.00 Ch 1 . = |20 Ch1: Start 2.40000 GHza —— Stop 2.80000 GHz Status __CH 1: C" 1—Port Avg=20 Delay ECL Certificate No: D2600V2—1032_Sep18 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 17.09.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN:1032 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.18 S/m; & =51.2; p = 1000 kg/m> Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: Probe: EX3DV4 — SN7349; ConvF(7.81, 7.81, 7.81) @ 2600 MHz; Calibrated: 30.12.2017 Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE4 $n601; Calibrated: 26.10.2017 Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 108.8 V/m; Power Drift = —0.08 dB Peak SAR (extrapolated) = 29.0 W/kg SAR(1 g) = 13.9 W/kg; SAR(10 g) = 6.17 W/kg Maximum value of SAR (measured) = 23.1 W/kg dB —5.20 —10.40 —15.60 —20.80 —26.00 0 dB = 23.1 W/kg = 13.64 dBW/kg Certificate No: D2600V2—1032_Sep18 Page 7 of 8

Impedance Measurement Plot for Body TSL File Yiew Channel Sweep Calibration Trace Scale Marker System Window Help e mm 2.600000 GHz 45.979 C 17.570 pF —3.4839 C 2.600000 GHz 55.394 mU —197.91 * Ch1Avg= 20 _ seA Ch1: Start 2.40000 GHa ——— Stop 2.80000 GHz .§00000 GHz —2$. 131 dB 0.00 5.00 10.00 15.00 20.00 25.00 30.00 35.00 0.00 Ch 1 &vg= 120 Ch1: Start 2.40000 GHza —— Stop 220000 GHz Status CH 1: C 1.Por Avg=20 Delay Certificate No: D2600V2—1032_Sep18 Page 8 of 8

Calibration . Laboratory of \\\\'////, *\\\/ S Schweizerischer Kalibrierdienst Schmid & Partner il_:\\/E! c Service suisse d‘étalonnage Englneering AG 2.z Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 27 ///\\\\\ S swiss Calibration Service Trlilibe®® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client Huawei—SZ (Auden) Certificate No: D5GHzV2—1155_Jun18 CALIBRATION CERTIFICATE Object D5GHzV2 — SN:1155 Calibration procedure(s) QA CAL—22.v3 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: June 08, 2018 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical forcalibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672/02673) Apr—19 Power sensor NRP—Z91 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—Z91 SN: 103245 04—Apr—18 (No. 217—026783) Apr—19 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—18 (No. 217—02682) Apr—19 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—18 (No. 217—02683) Apr—19 Reference Probe EX3DV4 SN: 3503 30—Dec—17 (No. EX3—3503_Dec17) Dec—18 DAE4 SN: 601 26—0ct—17 (No. DAE4—601_Oct17) Oct—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37202783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—17) In house check: Oct—18 Name Function Signature Calibrated by: Manu Seitz Laboratory Technician 32. Approved by: Katia Pokovic Technical Manager Issued: June 15, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D5GHzV2—1155_Jun18 Page 1 of 16

s : yo Callbratlon Laboratory of s\‘@/”@ S Schweizerischer Kalibrierdienst Schmid & Partner iIB\EE/ME@EE e Service suisse d‘étalonnage Engineering AG se Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {'/,,/fi\‘§§ S swiss Calibration Service Whilabs Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1155_Jun18 Page 2 of 16

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center— TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5250 MHz + 1 MHz 5400 MHz + 1 MHz Frequency 5600 MHz + 1 MHz 5750 MHz + 1 MHz 5850 MHz + 1 MHz Head TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.71 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 36.2 26 % 4.57 mho/m + 6 % Head TSL temperature change during test x6.5°C SAR result with Head TSL at 5250 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.14 W/kg SAR for nominal Head TSL parameters normalized to 1W 81.4 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.35 W/kg SAR for nominal Head TSL parameters normalized to 1W 23.5 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1155_Jun18 Page 3 of 16

Head TSL parameters at 5400 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.8 4.86 mho/m Measured Head TSL parameters (22.0 £0.2) °C 35.9 +6 % 4.73 mho/m + 6 % Head TSL temperature change during test x45"°C SAR result with Head TSL at 5400 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.33 W/kg SAR for nominal Head TSL parameters normalized to 1W 83.3 W / kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.39 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.9 W/kg + 19.5 % (k=2) Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.7 x6 % 4.94 mho/m + 6 % Head TSL temperature change during test «05 °C SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.52 W/kg SAR for nominal Head TSL parameters normalized to 1W 85.2 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.43 W/kg SAR for nominal Head TSL parameters normalized to 1W 24.3 Wikg x 19.5 % (k=2) Certificate No: D5GHzV2—1155_Jun18 Page 4 of 16

Head TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.4 5.22 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 35.4 +6 % 5.09 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5750 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 7.85 W/kg SAR for nominal Head TSL parameters normalized to 1W 78.4 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.23 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.3 Wikg * 19.5 % (k=2) Head TSL parameters at 5850 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.2 5.32 mho/m Measured Head TSL parameters (22.0 £0.2) °C 35.3 +6 % 5.20 mho/m + 6 % Head TSL temperature change during test <60.5 °C ~——— we«« SAR result with Head TSL at 5850 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.50 W/kg SAR for nominal Head TSL parameters normalized to 1W 85.4 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.41 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.3 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1155_Jun18 Page 5 of 16

Body TSL parameters at 5250 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.36 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.9 + 6 % 5.51 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5250 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.53 Wikg SAR for nominal Body TSL parameters normalized to 1W 74.7 Wikg # 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 100 mW input power 211 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.9 W/kg + 19.5 % (k=2) Body TSL parameters at 5400 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.7 5.53 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.7 x 6 % 5.71 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5400 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.93 Wikg SAR for nominal Body TSL parameters normalized to 1W 78.7 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.22 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.0 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1155_Jun18 Page 6 of 16

Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.3 + 6 % 5.99 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 8.02 W/kg SAR for nominal Body TSL parameters normalized to 1W 79.6 Wikg + 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.23 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.1 Wikg * 19.5 % (k=2) Body TSL parameters at 5750 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.3 5.94 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.0 x 6 % 6.19 mho/m + 6 % Body TSL temperature change during test <0.5 °C hn makh SAR result with Body TSL at 5750 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.39 W/kg SAR for nominal Body TSL parameters normalized to 1W 73.3 Wikg + 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.06 W/kg SAR for nominal Body TSL parameters normalized to 1W 20.4 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1155_Jun18 Page 7 of 16

Body TSL parameters at 5850 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.1 6.06 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 45.9 26 % 6.33 mho/m + 6 % Body TSL temperature change during test x0.5 °C SAR result with Body TSL at 5850 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.85 Wikg SAR for nominal Body TSL parameters normalized to 1W 78.1 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.18 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.7 Wikg £ 19.5 % (k=2) Certificate No: D5GHzV2—1155_Jun18 Page 8 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5250 MHz Impedance, transformed to feed point 55.3 Q — 8.1 jQ Return Loss — 20.8 dB Antenna Parameters with Head TSL at 5400 MHz Impedance, transformed to feed point 49.5 Q — 5.4 jQ Return Loss —25.3 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 59.2 Q — 6.3 jQ Return Loss —19.8 dB Antenna Parameters with Head TSL at 5750 MHz Impedance, transformed to feed point 57.3 Q — 2.8 jQ Return Loss —22.8 dB Antenna Parameters with Head TSL at 5850 MHz Impedance, transformed to feed point 55.4 Q — 6.7 jQ Return Loss —21.8 dB Antenna Parameters with Body TSL at 5250 MHz Impedance, transformed to feed point 53.4 Q — 5.5 jQ Return Loss —24.1 dB Antenna Parameters with Body TSL at 5400 MHz Impedance, transformed to feed point 49.9 Q — 3.3 jQ Return Loss — 29.6 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 60.6 Q — 5.0 jQ Return Loss —19.5 dB Certificate No: D5GHzV2—1155_Jun18 Page 9 of 16


Document Created: 2019-03-11 15:38:11
Document Modified: 2019-03-11 15:38:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC