Test Report SAR Part6

FCC ID: QISMAR-LX1AM

RF Exposure Info

Download: PDF
FCCID_4291008

Calibration Laboratory of Schweizerischer Kallbrierdienst Schmid & Partner Service sulsse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Callbration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Muttilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters * DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. * Connector angle; The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. * The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. * DC Voltage Measurement Linearity: Veritication of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. * Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. * Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. * AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage * Input Offset Measurement Output voltage and statistical results over a large numberof zero voltage measurements. * Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. * Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. * Low Baitery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. «_ Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—1291_Dec18 Page 2 of 5

C DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1198 6.1uV . full range = —100...+300 mV Low Range: 1LSB = 61nV , full range = > ... +8mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors s ¥ 2 High Range 402.580 + 0.02% (k=2) 408.249 £ 0.02% (k=2) 403.163 £0.02% (k=2) Low Range 3.97560 £ 1.50% (k=2) 3.97886 £ 1.50%(k=2) 3.97558 £ 1.50% (k=2) Connector Angle i Connector Angle to be used in DASY system 164.5°%41° Certificate No: DAE4—1291_Dec18 Page 3 of 5

Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltage Linearity High Range Reading (V) Difference (1V) Error (%) Channel X + Input 20003851 1.95 0.00 Channel X +Input 20006.61 1.29 0.01 Channel X > Input ©20003.34 2.94 —0.01 Channel Y + Input 200036.77 0.05 0.00 Channel Y + Input 20003.65 +1.54 —0.01 Channel Y > Input +20006.11 0.22 —0.00 Channel 2 + Input 200035.08 ~1.41 —0.00 Channel Z + Input 20002.62 —2.58 —0.01 Channel Z > Input +20006.40 —0.06 0.00 Low Range Reading (rV) Difference (V) Error (%) Channel X + Input 2001.29 0.31 0.02 Channel X + Input 201.13 0.32 0.16 Channel X ~Input —198.59 0.30 +0.15 Channel Y + Input 2000.40 —0.49 —0.02 Channel Y + Input 200.21 —0.66 —0.33 Channel Y > Input +199.89 —0.99 0.50 Channel Z + Input 2000.44 —0.41 —0.02 Channel Z + Input 199.70 —1.05 —0.52 Channel Z — Input —200.88 +1.78 0.89 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 seo; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (uV) Average Reading (1V) Channel X 200 10.02 7.91 —200 —6.52 —8.20 Channel Y 200 14.18 13.58 +200 +15.10 ~15.62 Channel Z 200 ~17.07 ~17.23 ~200 14.74 14.83 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec: Measuringtime: 3 sec Input Voltage (mV) Channel X (uV) Channel Y (uV) Channel Z (uV) Channel X 200 > —0.01 ~4.47 Channel Y 200 7.58 — 0.48 Channel Z 200 11.17 4.87 Certificate No: DAE4—1291_Deci8 Page 4 of 5

C 4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec: Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 16117 16241 Channel Y 15930 16718 Channel Z 16177 17128 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MG Average (wV) min. Offset(uV) max. Offset (uV) * [(’:“,’;""‘" Channel X —0.59 +1.81 0.89 0.47 Channel Y 147 —0.04 2.05 0.45 Channel Z. 112 —2.70 0.51 0.57 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channel X 200 200 Channel Y 200 200 Channel Z 200 200 Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vee) +7.9 Supply (— Vee) —7.6 Power Consumption (Typical values for information) Typicalvalues Switched off(mA) Stand by (mA) Transmitting (mA) Supply (+ Vee) +0.01 +6 +14 Supply (— Vee) —0.01 —8 8 Certificate No: DAE4—1291_Dec18 Page 5 of 5

FCC SAR Test Report Report No.: R1905H0093-S1 ANNEX L:The EUT Appearances and Test Configuration The Detailed EUT Appearance and Test Configuration refer to EUT Appearance and SAR Test Setup. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 264 of 264 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.


Document Created: 2019-05-23 16:58:35
Document Modified: 2019-05-23 16:58:35
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC