Appendix C Calibration certificate_part 1 of 6

FCC ID: QISCLT-L29

RF Exposure Info

Download: PDF
FCCID_4139959

Report No: E5/2018/C0051 Appendix C Calibration certificate 1. Dipole D750V3-SN 1160(2016-6-22) D835V2-SN 4d105(2016-12-08) D1750V2-SN 1149(2016-6-23) D1900V2-SN 5d028(2016-12-07) D2450V2-SN 733(2016-12-07) D2600V2-SN 1125(2016-6-22) D5GHzV2-SN 1165(2016-12-13) 2. DAE DAE4-SN 1428(2018-01-17) DAE4-SN 896(2018-11-08) 2. Probe EX3DV4-SN 3962(2018-01-11) EX3DV4-SN 3789(2018-02-08)

Calibration Laboratory of «7 g Schweizerischer Kalibrierdienst Schmid & Partner iia\éfi{/fli%i Service suissed‘étaionnage Engineering AG *s C servicio sviezero d terstura Zeughausstrasse 43, 8004 Zurich, Switzerland 5ns S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client SGS—SZ (Auden) Certificate No: D750V3—1160_Jun16 ICALIBRATION CERTIFICATE | Object D750V3 — SN:1160 Calibration procedure(s) QA CAL—05.v9 Calibration procedure for dipole validation kits above 700 MHz Calibration date: June 22, 2016 This calibration certificate documents the traceabilty to national standards, which realizethe physical units of measurements (S1). The measurements and the uncertainties with confidence probabilty are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facifty: environment temperature (22 3)°C and humidity < 70% Callbration Equipment used (M&TE critical for callbration) Primary Standards 1# Cal Date (Gertificate No.) Scheduled Calibration Power meter NRP SN: 104778 06—Aor—16 (No. 217—02288/02209) Aprt7 Power sensor NRP—291 SN: 108244 06—Aor—16 (No. 217—02288) Apr—t7 Power sensor NRP—291 SN: 103245 06—Aor—16 (No. 217—02289) Apr—t7 Reference 20 dB Attenuator SN: 5058 (20k) 05—Ror—16 (No. 217—02202) Apr—t7 Type—N mismatch combination SN: 5047.2 / 06327 05—Aor—16 (No. 217—02205) Apr—t7 Reference Probe EX3DV4 SN: 7349 15—Jun—16 (No. EX3—7349_Jun16) Jun—17 DAE4 SN: 601 30—Dec—15 (No. DAE4—601_Dect5) Dec—16 Secondary Standards iD # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (No. 217—02222) in house check Oct—16 Power sensor HP 8481A SN: US37202783 07—Oct—15 (No. 217—02222) in house check: Oct—16 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (No. 217—02223) in house check Oct—16 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Jun—15) in house check: Oct—16 Network Analyzer HP 8753E SN: US37390585 18—0ct—01 (in house check Oct—15) in house check Oct—16 Name Function Signature Calibrated by: Jeton Kastrati Laboratory Technician \ ) csll w« Approved by: Katia Pokovie Technical Manager %f/f’ Issued: June27, 2016 This calibration certificate shall not be reproduced except in full without writen approval of the laboratory. Certificate No: D750V3—1160_Jun16 Page 1 of 8

Calibration 4 Laboratory of «g Schweizerischer Kalibrierdienst Schmid & Partner Service suissed‘étalonnage Engineering AG C sevigesmmerssitersturs Zeughausstrasse 43, 8004 Zurich, Switzerland S swiss Calibration Service Aceredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)®, February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. & SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D750V3—1160_Jun16 Page 2 of 8

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY3 V52.8.8 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 750 MHz + 1 MHz Head TSL parameters Thefollowing parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 41.9 0.89 mho/m Measured Head TSL parameters (22.0 £0.2) °C 41.6 £ 6 % 0.91 mho/m 6% Head TSL temperature change during test <0.5 °C SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 2.08 W/kg SAR for nominal Head TSL parameters normalized to 1W 8.17 Wikg 17.0 %(k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 1.36 Wkg SAR for nominal Head TSL parameters normalized to 1W 5.36 Wikg * 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 55.5 0.96 mho/m Measured Body TSL parameters (22.0 £0.2) °C 55.4 26 % 1.00 mho/m + 6 % Body TSL temperature change during test <0.5 °C «— SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 2.21 Wikg SAR for nominal Body TSL parameters normalized to 1W 8.57 Wikg » 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 145 Wikg SAR for nominal Body TSL parameters normalized to 1W 5.66 Wikg 2 16.5 % (k=2) Certificate No: D750V3—1160_Jun16 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 54.8 0 — 1.6 io Return Loss —26.3 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 50.2 Q — 3.8 i2 Return Loss —28.4 dB General Antenna Parameters and Design Electrical Delay(one direction) 1.040 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of thedipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions* paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on * November 19, 2015 Certificate No: D750V3—1160_Jun16 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 22.06.2016 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 750 MHz; Type: D750V3; Serial: D750V3 — SN:1160 Communication System: UID 0 — CW; Frequency: 750 MHz Medium parameters used: f = 750 MHz; 0 = 0.91 S/m; & =41.6; p = 1000 kym" Phantomsection: Flat Section Measurement Standard: DASY5 (IEEEAEC/ANSI C63.19—2011) DASY52 Configuration: Probe: EX3DV4 — SN7349; ConvF(10.17, 10.17, 10.17); Calibrated: 15.06.2016; Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE4 $n601; Calibrated: 30.12.2015 Phantom: Flat Phantom 4.9L; Type: QDOOOP49AA; Serial: 1001 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7372) Dipole Calibration for Head Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 57.89 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 3.12 W/kg SAR(I g) = 2.08 W/kg; S AR(10 g) = 1.36 W/kg Maximum value of SAR (measured) = 2.76 W/kg —2.00 —4.00 —6.00 —10.00 0 dB = 2.76 W/kg =4.41 dBW/kg Certificate No: D750V3—1160_Jun16 Page 5 of 8

Impedance Measurement Plot for Head TSL 22 Jun 2016 13:36:11 CH® san a uors m 54.022 0 ~1,5723 0 134.97 pF 75e.000 000 MXz fvg 16 Hid cn2 si1 Los _5 dB/REF —20_a8 f m~26.300 aB 750,000 000 IMHz Ca igs . 1 + : + + + + + } + } | } + 1 + } Hie } } + + + L —| } } start 550.000 000 hz — — StoP 950.000 000 mHz Certificate No: D750V3—1160_Jun16 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 22.06.2016 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 750 MHz; Type: D750V3; Serial: D750V3 — SN:1160 Communication System: UID 0 — CW; Frequency: 750 MHz . Medium parameters used: = 750 MHz; 0 = 1 S/m; s = 55.4; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY3 (IEEEAEC/ANSI C63.19—2011) DASY52 Configuration: «+ Probe: EX3DV4 — SN7349; ConyF(9.99, 9.99, 9.99); Calibrated: 15.06.2016; * Sensor—Surface; 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 30.12.2015 *« Phantom: Flat Phantom 4.9L; Type: QDOOOPA49AA; Serial: 1001 + DASY52 52.8.8(1258); SEMCAD X 14.6.10(7372) Dipole Calibration for Body Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 56.66 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 3.29 W/kg SAR(I g) =2.21 W/kg; SAR(10 g) = 1.45 W/kg Maximum value of SAR (measured) =2.93 W/kg —2.00 ~4.00 —6.00 —8.00 —10.00 0 dB = 2.93 W/kg = 4.67 dBW/kg Certificate No: D750V3—1160_Jun16 Page 7 of 8

Impedance Measurement Plot for Body TSL 22 Jun zeie 10:5e:20 CH® sn i uors m 50164 a —3.7969 n 55.090 pF 750.000 0g0 MHz Ay lEs Hid cn2 sii_ Los .5 dB/REF —20_d8 . 750.000 000 nHz Ca L | 1 1 2 L 1 . } By 165 + / + — I + 4 + + Hid + | } 4 £F L 4 ; } SthRT s50.000 000 MHz — — stoP 950.000 con mz Certificate No: D750V3—1160_Jun16 Page 8 of 8

In Collaboration with \1p1 wl l/1‘4,2 HEBVLH * w ‘/"/"J, p__C_ §\\\/’3 A EiA —V CALIBRATION LABORATORY MCNAS 2 *» Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China %,/@\§ v CAUBRAHON Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 AululabsS® CNAS LO570 E—mail: cttl@chinattl.com Http://www.chinattl.cn Client SGS(Boce) Certificate No: Z16—97239 CALIBRATION CERTIFICATE Object D835V2 — SN: 40105 Calibration Procedure(s) FD—Z11—003—01 Calibration Procedures for dipole validation kits Calibration date: December 8, 2016 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(Sl). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22+3)‘C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 101919 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Power sensor NRP—Z91 101547 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Reference Probe EX3DV4 SN 7433 26—Sep—16(SPEAG,No.EX3—7433_Sep16) Sep—17 DAE4 SN 771 02—Feb—16(CTTL—SPEAG,No.Z16—97011) Feb—17 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 01—Feb—16 (CTTL, No.J16X00893) Jan—17 Network Analyzer E5071C MY46110673 26—Jan—16 (CTTL, No.J16X00894) Jan—17 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer & é i/ | Reviewed by: Qi Dianyuan SAR Project Leader §2 g__ gor Approved by: Lu Bingsong Deputy Director of the laboratory Issued: Decemb J 11, 2016 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z16—97239 Page 1 of 8

In Collaboration with §7T7Jj a CALIBRATION LABORATORY e Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn Glossary: TSL tissue simulating liquid Convr sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) For hand—held devices used in close proximity to the ear (frequency range of 300MHz to 3GHz)", February 2005 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z16—97239 Page 2 of 8

In Collaboration with @TTL a CALIBRATION LABORATORY y Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn Measurement Conditions DASY system configuration, as far as notgiven on page 1. DASY Version DASY52 52.8.8.1258 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 835 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 41.5 0.90 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 40.8 +6 % 0.91 mho/m +6 % Head TSL temperature change during test <1.0 °C ———— _——— SAR result with Head TSL SAR averaged over 1 Cmm‘ (1 g) of Head TSL Condition SAR measured 250 mW input power 2.43 mW / g SAR for nominal Head TSL parameters normalized to 1W 9.59 mW /g + 20.8 % (k=2) SAR averaged over 10 cm (10 g) of Head TSL Condition SAR measured 250 mW input power 1.59 mW / g SAR for nominal Head TSL parameters normalized to 1W 6.29 mW /g + 20.4 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 55.2 0.97 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 54.7 £6 % 0.98 mho/m +6 % Body TSL temperature change during test <1.0 °C ———— SAR result with Body TSL SAR averaged over 1 Cm" (1 g) of Body TSL Condition SAR measured 250 mW input power 2.44 mW / g SAR for nominal Body TSL parameters normalized to 1W 9.65 mW /g + 20.8 % (k=2) SAR averaged over 10 cm> (10 g) of Body TSL Condition SAR measured 250 mW input power 1.63 mW / g SAR for nominal Body TSL parameters normalized to 1W 6.46 mW /g + 20.4 % (k=2) Certificate No: Z16—97239 Page 3 of 8

E7TTL $.P.g—2 V Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn Appendix Antenna Parameters with Head TSL Impedance, transformed to feed point 49.20— 3.41j0Q Return Loss — 29.10B Antenna Parameters with Body TSL Impedance, transformed to feed point 45.80— 3.25j0 Return Loss — 25.10B General Antenna Parameters and Design Electrical Delay (one direction) 1.500 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z16—97239 Page 4 of 8

ETTL $.2.g.2 ‘/ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn DASYS5 Validation Report for Head TSL Date: 12.08.2016 Test Laboratory: CTTL, Beijing, China DUT : Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN: 40105 Communication System: UID 0, CW; Frequency: 835 MHz; Duty Cycle: 1: 1 Medium parameters used: f= 835 MHz; 0 = 0.912 S/m; s, = 40.78; p = 1000 kg/m* Phantom section: Center Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: e Probe: EX3DV4 — SN7433; ConvF(9.82, 9.82, 9.82); Calibrated: 9/26/2016; e Sensor—Surface: 2mm (Mechanical Surface Detection) e Electronics: DAF4 Sn771; Calibrated: 2/2/2016 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 e Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 49.08V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 3.62 W/kg SAR(I g) =2.43 W/kg; SAR(10 g) = 1.59 W/kg Maximum value of SAR (measured) = 3.08 W/kg dB 0 —2.09 —4.18 —6.26 —8.35 0 dB = 3.08 W/kg = 4.89 dBW/kg Certificate No: Z16—97239 Page 5 of 8

fi l;ColIabonmonewith 3 ‘ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn Impedance Measurement Plot for Head TSL Tri s11 Log Mag 10.00dB/ Ref 0.000dsB [F1] 900 1 ~g35. 000006 mhz —29. 063 ds 40. 00 30. 00 20. 00 10. 00 0. 000 p —10. 00 —20. 00 4 —30. 00 —40. 00 —50. 00 s |PM@H s11 smith (R+jx) scale 1.000Uu [F1 del] »1 835.00000 mhz 49.239 o —3.4139 o SSW’ \ IFBW 100Hz Certificate No: Z16—97239 Page 6 of 8

8 In Collaboration with "__—j"TTI, _ CALIBRATION LABORATORY V Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn DASYS Validation Report for Body TSL Date: 12.08.2016 Test Laboratory: CTTL, Beijing, China DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN: 40105 Communication System: UID 0, CW; Frequency: 835 MHz; Duty Cycle: 1:1 Medium parameters used: f= 835 MHz; 0 = 0.983 S/m; g, = 54.74; p = 1000 kg/m3 Phantom section: Right Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: e Probe: EX3DV4 — SN7433; ConvF(9.5,9.5, 9.5); Calibrated: 9/26/2016; e Sensor—Surface: 2mm (Mechanical Surface Detection) e Electronics: DAE4 Sn771; Calibrated: 2/2/2016 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 e Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 57.10 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 3.54 W/kg SAR(1 g) = 2.44 W/kg; SAR(10 g) = 1.63 W/kg Maximum value of SAR (measured) = 3.06 W/kg dB 0 —1.97 —3.94 —5.91 —1.88 L* _———1 —9.85 0 dB = 3.06 W/kg = 4.86 dBW/kg Certificate No: Z16—97239 Page 7 of 8

iiEEEF!EF::;;E;EiE;/ ::Lllflllflfl'flflJfiE;UB()iz;NUI'Y m Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.cn Impedance Measurement Plot for Body TSL Tri s11 Log Mag 10.00dB/ Rref 0.000ds [F1] 990 1 ~g35. 00000 mhz —25. 066 d 40. 00 30. 00 20. 00 10. 00 0. 000 p, —10. 00 —20. 00 —30. 00 —40. 00 —50. 00 7 Ah. P0 sii smith (r+jx) scale 1.000u [F1 del] »1 835.00000 mHz 45.756 o —3.2528 o 58.59 _ Certificate No: Z16—97239 Page 8 of 8

Calibration f Laboratory of um s3 g Schweizerischer Kalibrierdienst Schmid & Partner SBE/W/BE @ Service suisse d‘étalonnage Engineering AG Tof Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland */,fi. w S swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is oneof the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client SGS—SZ (Auden) Certificate No: D1750V2—1149_Jun16 CALIBRATION CERTIFICATE $ I Object D1750V2 — SN:1149 Calibration procedure(s) QA CAL—05.v9 Calibration procedure for dipole validation kits above 700 MHz Calibration date: June 23, 2016 This calibration certificate documents the traceabilty to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probabilty are given on the following pages and are part of the cortficate. All callbrations have been conducted in the closed laboratory facifty: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE crtical for calibration) Primary Standards 1D # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 06—Apr—16 (No. 217—02288/02289) Apr—17 Power sensor NRP—Z91 SN: 108244 06—Apr—16 (No. 217—02288) Apr—17 Power sensor NRP—Z91 SN: 103245 06—Apr—16 (No. 217—02289) Apr—17 Reference 20 dB Attenuator SN: 5058 (20k) 05—Apr—16 (No. 217—02202) Apr—17 Type—N mismatch combination SN: 5047.2 / 06827 05—Apr—16 (No. 217—02205) Apr—17 Reference Probe EX3DV4 SN: 7849 15—Jun—16 (No. EX3—7349_Junt6) Jun—17 DAE4 SN: 601 30—Dec—15 (No. DAE4—601_Dect5) Dec—16 Secondary Standards 1D # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—0ct—15 (No. 217—02222) In house check: Oct—16 Power sensor HP 8481A SN: US37202783 07—0ct—15 (No. 217—02222) in house check: Oct—16 Power sensor HP 8481A SN: MY41092317 07—0ct—15 (No. 217—02223) in house chack: Oct—16 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Jun—15) in house check: Oct—16 Network Analyzer HP 8753E S Ussrsaoses 18—0ct—01 (in house check Oct—15) in house check: Oct—16 Name Function Signature Calibrated by: Michael Waber Laboratory Technician % Katja Pokovic Technical Manager ////%/: Approved by: Issued: June 28, 2016 This callbration certificate shall not be reproduced exceptin full without written approval of the laboratory. Certificate No: D1750V2—1149_Jun16 Page 1 of 8

Calibration Laboratory of g Schweizerischer Kalibrierdienst Schmid & Partner Service suisse d‘étalonnage Engineering AG C Servizio svizzero di taratura Zeughausstrasse 48, 8004 Zurich, Switzerland mlutaied S swiss Calibration Service Accredited by the Swiss Accreditation Service (GAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear(frequency range of 300 MHz to 3 GHz)", February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D1750V2—1149_Jun16 Page 2 of 8

Measurement Conditions DASY system contfiguration, as far as not iven on page 1. DASY Version DASY5 V52.8.8 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx. dy, dz =5 mm Frequency 1750 MHz a 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.1 1.37 mho/m Measured Head TSL parameters (22.0 £0.2) °C 39.8 2 6 % 1.36 mho/m + 6 % Head TSL temperature change during test <0.5 °C —— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 9.16 Wikg SAR for nominal Head TSL parameters normalized to 1W 36.7 Wikg # 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 4.87 Wikg SAR for nominal Head TSL parameters normalized to 1W 19.5 Wikg 2 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Conductivity Nominal Body TSL parameters 22.0 °C 53.4 1.49 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 53.8 £ 6 % 1.50 mho/m + 6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL SAR averaged over 1 cm° (1 g) of Body TSL Condition SAR measured 250 mW input power 9.27 Wikg SAR for nominal Body TSL parameters normalized to 1W 37.0 Wikg » 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 4.93 Wikg SAR for nominal Body TSL parameters normalized to 1W 19.7 Wikg 2 16.5 % (k=2) Certificate No: D1750V2—1149_Jun16 Page 3 of 8


Document Created: 2019-01-23 13:50:02
Document Modified: 2019-01-23 13:50:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC