Test Report_RF

FCC ID: QISCLT-L29

Test Report

Download: PDF
FCCID_4139881

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Report No.: HR/2018/C000201 Technology Park, Nanshan District, Shenzhen, Page: 1 of 26 Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: ee.shenzhen@sgs.com FCC REPORT Application No: HR/2018/C0002 Applicant: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Address of Applicant: Bantian, Longgang District, Shenzhen, 518129, P.R.C Manufacturer: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Address of Manufacturer: Bantian, Longgang District, Shenzhen, 518129, P.R.C Factory: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Address of Factory: Bantian, Longgang District, Shenzhen, 518129, P.R.C Product Name: Smart Phone Model No.(EUT): CLT-L29 Trade Mark: HUAWEI FCC ID: QISCLT-L29 Standards: 47 CFR FCC Part 2 47 CFR FCC Part 24 47 CFR FCC Part 27 Test Method: FCC KDB 971168 D01 Power Meas License Digital Systems v03 TIA-603-E 2016 Date of Receipt: 2018-12-08 Date of Test: 2018-12-09 to 2018-12-17 Date of Issue: 2018-12-17 Test Result: PASS * * In the configuration tested, the EUT detailed in this report complied with the standards specified above. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 2 of 26 1 Version Revision Record Version Chapter Date Modifier Remark 01 2018-12-17 Original Authorized for issue by: Tested By 2018-12-17 (Mike Hu) /Project Engineer Date Checked By 2018-12-17 (David Chen) /Reviewer Date This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 3 of 26 2 Test Summary 2.1 LTE CA_2C Test Item FCC Rule No. Requirements Test Result Verdict Effective (Isotropic) §2.1046, Section 1 of Radiated Power EIRP ≤ 2 W Pass §24.232 Appendix B Output Data Peak-Average §2.1046, Section 2 of Limit≤13 dB Pass Ratio §24.232 Appendix B Modulation Section 3 of §2.1047 Digital modulation Pass Characteristics Appendix B OBW: No limit. Section 4 of Bandwidth §2.1049 Pass EBW: No limit. Appendix B ≤ -13 dBm/1%*EBW, in 1 MHz bands Band Edges §2.1051, Section 5 of immediately outside and adjacent to the Pass Compliance §24.238 Appendix B frequency block. Spurious Emission ≤ -13 dBm/1 MHz, from 9 kHz to 10th §2.1051, Section 6 of at Antenna harmonics but outside authorized Pass §24.238 Appendix B Terminals operating frequency ranges. Field Strength of §2.1053, Section 7 of ≤ -13 dBm/1 MHz. Pass Spurious Radiation §24.238 Appendix B §2.1055, Section 8 of Frequency Stability ≤ ±2.5 ppm. Pass §24.235 Appendix B NOTE:For the verdict, the “N/A” denotes “not applicable”, the “N/T” denotes “not tested”. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 4 of 26 2.2 LTE CA_7C Test Item FCC Rule No. Requirements Test Result Verdict Effective (Isotropic) §2.1046, Section 1 of Radiated Power EIRP ≤ 2W Pass §27.50(h) Appendix B Output Data Peak-Average Section 2 of §27.50(a) Limit≤13 dB Pass Ratio Appendix B Modulation Section 3 of §2.1047 Digital modulation Pass Characteristics Appendix B OBW: No limit. Section 4 of Bandwidth §2.1049 Pass EBW: No limit. Appendix B Band Edges §2.1051, Section 5 of Pass Compliance §27.53(m4) Appendix B Spurious Emission §2.1051, Section 6 of at Antenna Pass §27.53(m) Appendix B Terminals Field Strength of §2.1053, Section 7 of Pass Spurious Radiation §27.53(m) Appendix B §2.1055, Within authorized bands of Section 8 of Frequency Stability Pass §27.54 operation/frequency block. Appendix B NOTE:For the verdict, the “N/A” denotes “not applicable”, the “N/T” denotes “not tested”. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 5 of 26 2.3 LTE CA_38C Test Item FCC Rule No. Requirements Test Result Verdict Effective (Isotropic) Pass §2.1046, Section 1 of Radiated Power EIRP ≤ 2W §27.50(h) Appendix B Output Data Peak-Average Section 2 of §27.50(a) FCC: Limit≤13 dB Pass Ratio Appendix B Modulation Section 3 of §2.1047 Digital modulation Pass Characteristics Appendix B §2.1049 OBW: No limit. Section 4 of Bandwidth Pass EBW: No limit. Appendix B Band Edges §2.1051, Section 5 of Pass Compliance §27.53(m) Appendix B Spurious Emission §2.1051, Section 6 of at Antenna Pass §27.53(m) Appendix B Terminals Field Strength of §2.1053, Section 7 of Pass Spurious Radiation §27.53(m) Appendix B §2.1055, Within authorized bands of Section 8 of Frequency Stability Pass §27.54 operation/frequency block. Appendix B NOTE:For the verdict, the “N/A” denotes “not applicable”, the “N/T” denotes “not tested”. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 6 of 26 2.4 LTE CA_41C FCC Rule Test Item Requirements Test Result Verdict No. Effective (Isotropic) §2.1046, Section 1 of Radiated Power EIRP ≤ 2W Pass §27.50(h) Appendix B Output Data Section 2 of Peak-Average Ratio §27.50(a) FCC:Limit≤13 dB Pass Appendix B Modulation Section 3 of §2.1047 Digital modulation Pass Characteristics Appendix B OBW: No limit. Section 4 of Bandwidth §2.1049 Pass EBW: No limit. Appendix B Band Edges §2.1051, Section 5 of Pass Compliance §27.53(m) Appendix B Spurious Emission at §2.1051, Section 6 of Pass Antenna Terminals §27.53(m) Appendix B Field Strength of §2.1053, Section 7 of Pass Spurious Radiation §27.53(m) Appendix B §2.1055, Within authorized bands of Section 8 of Frequency Stability Pass §27.54 operation/frequency block. Appendix B NOTE:For the verdict, the “N/A” denotes “not applicable”, the “N/T” denotes “not tested”. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 7 of 26 Content 1 VERSION ......................................................................................................................................................... 2 2 TEST SUMMARY ............................................................................................................................................ 3 2.1 LTE CA_2C .................................................................................................................................................... 3 2.2 LTE CA_7C .................................................................................................................................................... 4 2.3 LTE CA_38C .................................................................................................................................................. 5 2.4 LTE CA_41C .................................................................................................................................................. 6 3 GENERAL INFORMATION ............................................................................................................................ 9 3.1 CLIENT INFORMATION ...................................................................................................................................... 9 3.2 TEST LOCATION............................................................................................................................................... 9 3.3 TEST FACILITY ................................................................................................................................................. 9 3.4 GENERAL DESCRIPTION OF EUT .................................................................................................................. 10 3.5 TEST MODE ................................................................................................................................................... 10 3.6 TEST ENVIRONMENT ..................................................................................................................................... 10 3.7 TEST FREQUENCY ......................................................................................................................................... 11 3.7.1 Table 4.3.1.1.2A-2: Test frequencies for CA_2C ............................................................................... 11 3.7.2 Table 4.3.1.1.1A-1: Test frequencies for CA_7C ............................................................................... 12 3.7.3 Table 4.3.1.2.6A-1: Test frequencies for CA_38C ............................................................................. 12 3.7.4 Table 4.3.1.2.9A-1: Test frequencies for CA_41C ............................................................................. 13 3.8 TECHNICAL SPECIFICATION .......................................................................................................................... 14 4 DESCRIPTION OF TESTS............................................................................................................................15 4.1 CONDUCTED OUTPUT POWER ...................................................................................................................... 15 4.2 EFFECTIVE (ISOTROPIC) RADIATED POWER OF TRANSMITTER ................................................................... 15 4.3 OCCUPIED BANDWIDTH ................................................................................................................................. 16 4.4 BAND EDGE AT ANTENNA TERMINALS .......................................................................................................... 16 4.5 SPURIOUS AND HARMONIC EMISSIONS AT ANTENNA TERMINAL ................................................................. 16 4.6 PEAK-AVERAGE RATIO ................................................................................................................................. 17 4.7 FIELD STRENGTH OF SPURIOUS RADIATION ................................................................................................ 17 4.8 FREQUENCY STABILITY / TEMPERATURE VARIATION ................................................................................... 18 4.9 TEST SETUPS ................................................................................................................................................ 18 4.9.1 Test Setup 1 ............................................................................................................................................ 18 4.9.2 Test Setup 2 ............................................................................................................................................ 19 4.9.3 Test Setup 3 ............................................................................................................................................ 20 4.9.4 Test Setup 4 ............................................................................................................................................ 21 4.10 TEST CONDITIONS ......................................................................................................................................... 22 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 8 of 26 5 MAIN TEST INSTRUMENTS ........................................................................................................................24 6 MEASUREMENT UNCERTAINTY ...............................................................................................................26 7 PHOTOGRAPHS - EUT CONSTRUCTIONAL DETAILS ...........................................................................26 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 9 of 26 3 General Information 3.1 Client Information Applicant: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Address of Applicant: Bantian, Longgang District, Shenzhen, 518129, P.R.C Manufacturer: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Address of Manufacturer: Bantian, Longgang District, Shenzhen, 518129, P.R.C Factory: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Ltd., Address of Factory: Bantian, Longgang District, Shenzhen, 518129, P.R.C 3.2 Test Location Company: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Address: Shenzhen, Guangdong, China Post code: 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 E-mail: ee.shenzhen@sgs.com 3.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 10 of 26 3.4 General Description of EUT Product Name: Smart Phone Model No.: CLT-L29 Trade Mark: HUAWEI Hardware Version: HL1CLTM Software Version: CLT-L29 8.1.0.178(C900) Sample Type: Portable Device, Module Antenna Type: External, Integrated LTE CA_2C: -0.39 dBi(Main Antenna); -1.57 dBi(Secondary Antenna) LTE CA_7C: 1.58 dBi(Main Antenna);-2.52 dBi(Secondary Antenna) Antenna Gain: LTE CA_38C: 1.96 dBi(Main Antenna);-3.46 dBi(Secondary Antenna) LTE CA_41C: 1.20 dBi(Main Antenna);-1.70 dBi(Secondary Antenna) 3.5 Test Mode Test Mode Test Modes Description LTE/TM1 LTE system, QPSK modulation LTE/TM2 LTE system, 16QAM modulation LTE/TM3 LTE system, 64QAM modulation 3.6 Test Environment Environment Parameter Selected Values During Tests Relative Humidity 52% Atmospheric Pressure: 101.3KPa Temperature TN 25 °C VL 3.6V Voltage : VN 3.82V VH 4.35V NOTE: VL= lower extreme test voltage VN= nominal voltage VH= upper extreme test voltage TN= normal temperature This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 11 of 26 3.7 Test Frequency 3.7.1 Table 4.3.1.1.2A-2: Test frequencies for CA_2C CC1 CC2 CC-Combo / Note1 Note1 Range NRB_agg BW fUL fDL BW fUL fDL [RB] NUL NDL NUL NDL [RB] [MHz] [MHz] [RB] [MHz] [MHz] 25 18633 1853.3 633 1933.3 100 18750 1865 750 1945 25+100 100 18700 1860 700 1940 25 18817 1871.7 817 1951.7 50 18653 1855.3 653 1935.3 75 18773 1867.3 773 1947.3 50+75 75 18675 1857.5 675 1937.5 50 18795 1869.5 795 1949.5 50 18655 1855.5 655 1935.5 100 18799 1869.9 799 1949.9 Low 50+100 100 18700 1860 700 1940 50 18844 1874.4 844 1954.4 75+75 75 18675 1857.5 675 1937.5 75 18825 1872.5 825 1952.5 75 18678 1857.8 678 1937.8 100 18849 1874.9 849 1954.9 75+100 100 18700 1860 700 1940 75 18871 1877.1 871 1957.1 100+100 100 18700 1860 700 1940 100 18898 1879.8 898 1959.8 25 18808 1870.8 808 1950.8 100 18925 1882.5 925 1962.5 25+100 100 18875 1877.5 875 1957.5 25 18992 1889.2 992 1969.2 50 18829 1872.9 829 1952.9 75 18949 1884.9 949 1964.9 50+75 75 18851 1875.1 851 1955.1 50 18971 1887.1 971 1967.1 50 18806 1870.6 806 1950.6 100 18950 1885 950 1965 Mid 50+100 100 18851 1875.1 851 1955.1 50 18995 1889.5 995 1969.5 75+75 75 18825 1872.5 825 1952.5 75 18975 1887.5 975 1967.5 75 18803 1870.3 803 1950.3 100 18974 1887.4 974 1967.4 75+100 100 18826 1872.6 826 1952.6 75 18997 1889.7 997 1969.7 100+100 100 18801 1870.1 801 1950.1 100 18999 1889.9 999 1969.9 25 18983 1888.3 983 1968.3 100 19100 1900 1100 1980 25+100 100 19050 1895 1050 1975 25 19167 1906.7 1167 1986.7 50 19005 1890.5 1005 1970.5 75 19125 1902.5 1125 1982.5 50+75 75 19027 1892.7 1027 1972.7 50 19147 1904.7 1147 1984.7 50 18956 1885.6 956 1965.6 100 19100 1900 1100 1980 High 50+100 100 19001 1890.1 1001 1970.1 50 19145 1904.5 1145 1984.5 75+75 75 18975 1887.5 975 1967.5 75 19125 1902.5 1125 1982.5 75 18929 1882.9 929 1962.9 100 19100 1900 1100 1980 75+100 100 18951 1885.1 951 1965.1 75 19122 1902.2 1122 1982.2 100+100 100 18902 1880.2 902 1960.2 100 19100 1900 1100 1980 Note 1: Carriers in increasing frequency order. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 12 of 26 3.7.2 Table 4.3.1.1.1A-1: Test frequencies for CA_7C CC1 CC2 CC-Combo / Note1 Note1 Range NRB_agg BW fUL fDL BW fUL fDL [RB] NUL NDL NUL NDL [RB] [MHz] [MHz] [RB] [MHz] [MHz] 50 20805 2505.5 2805 2625.5 100 20949 2519.9 2949 2639.9 50+100 100 20850 2510 2850 2630 50 20994 2524.4 2994 2644.4 75+75 75 20825 2507.5 2825 2627.5 75 20975 2522.5 2975 2642.5 Low 75 20828 2507.8 2828 2627.8 100 20999 2524.9 2999 2644.9 75+100 100 20850 2510 2850 2630 75 21021 2527.1 3021 2647.1 100+100 100 20850 2510 2850 2630 100 21048 2529.8 3048 2649.8 50 21006 2525.6 3006 2645.6 100 21150 2540 3150 2660 50+100 100 21051 2530.1 3051 2650.1 50 21195 2544.5 3195 2664.5 75+75 75 21025 2527.5 3025 2647.5 75 21175 2542.5 3175 2662.5 Mid 75 21003 2525.3 3003 2645.3 100 21174 2542.4 3174 2662.4 75+100 100 21026 2527.6 3026 2647.6 75 21197 2544.7 3197 2664.7 100+100 100 21001 2525.1 3001 2645.1 100 21199 2544.9 3199 2664.9 50 21206 2545.6 3206 2665.6 100 21350 2560 3350 2680 50+100 100 21251 2550.1 3251 2670.1 50 21395 2564.5 3395 2684.5 75+75 75 21225 2547.5 3225 2667.5 75 21375 2562.5 3375 2682.5 High 75 21179 2542.9 3179 2662.9 100 21350 2560 3350 2680 75+100 100 21201 2545.1 3201 2665.1 75 21372 2562.2 3372 2682.2 100+100 100 21152 2540.2 3152 2660.2 100 21350 2560 3350 2680 Note 1: Carriers in increasing frequency order. 3.7.3 Table 4.3.1.2.6A-1: Test frequencies for CA_38C CC1 CC2 CC-Combo / Note1 Note1 Range NRB_agg BW fUL/DL BW fUL/DL [RB] NUL/DL NUL/DL [RB] [MHz] [RB] [MHz] 75+75 75 37825 2577.5 75 37975 2592.5 Low 100+100 100 37850 2580 100 38048 2599.8 75+75 75 37925 2587.5 75 38075 2602.5 Mid 100+100 100 37901 2585.1 100 38099 2604.9 75+75 75 38025 2597.5 75 38175 2612.5 High 100+100 100 37952 2590.2 100 38150 2610 Note 1: Carriers in increasing frequency order. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 13 of 26 3.7.4 Table 4.3.1.2.9A-1: Test frequencies for CA_41C CC1 CC2 CC-Combo / Note1 Note1 Range NRB_agg BW fUL/DL BW fUL/DL [RB] NUL/DL NUL/DL [RB] [MHz] [RB] [MHz] 25 40165 2547.5 100 40282 2559.2 25+100 100 40240 2555 25 40357 2566.7 50 40190 2550 100 40334 2564.4 50+100 100 40240 2555 50 40384 2569.4 Low 75+75 75 40215 2552.5 75 40365 2567.5 75 40215 2552.5 100 40386 2569.6 75+100 100 40240 2555 75 40411 2572.1 100+100 100 40240 2555 100 40438 2574.8 25 40598 2590.8 100 40715 2602.5 25+100 100 40665 2597.5 25 40782 2609.2 50 40596 2590.6 100 40740 2565.0 50+100 100 40641 2595.1 50 40785 2609.5 Mid 75+75 75 40615 2592.5 75 40765 2607.5 75 40593 2590.3 100 40764 2607.4 75+100 100 40616 2592.6 75 40787 2609.7 100+100 100 40591 2590.1 100 40789 2609.9 25 41023 2633.3 100 41140 2645 25+100 100 41098 2640.8 25 41215 2652.5 50 40996 2630.6 100 41140 2645 50+100 100 41046 2635.6 50 41190 2650 High 75+75 75 41015 2632.5 75 41165 2647.5 75 40969 2627.9 100 41140 2645 75+100 100 40994 2630.4 75 41165 2647.5 100+100 100 40942 2625.2 100 41140 2645 Note 1: Carriers in increasing frequency order. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 14 of 26 3.8 Technical Specification Characteristics Description Radio System Type LTE_CA Transmission (TX): 1850 to 1910 MHz LTE CA_2C Receiving (RX):1970 to 1990 MHz Transmission (TX): 2500 to 2570 MHz LTE CA_7C Supported Frequency Receiving (RX):2620 to 2690 MHz Range Transmission (TX): 2570 to 2620 MHz LTE CA_38C Receiving (RX): 2570 to 2620 MHz Transmission (TX): 2545 to 2655 MHz LTE CA_41C Receiving (RX): 2545 to 2655 MHz LTE CA_2C: 24dBm LTE CA_7C: 22.6dBm Target TX Output Power LTE CA_38C: 23dBm LTE CA_41C: 23dBm 25+100; 50+75; 50+100; 75+75; 75+100, LTE CA_2C 100+100 50+100; 75+50; 75+75, 75+100 Supported Channel LTE CA_7C 100+100 Bandwidth LTE CA_38C 75+75; 100+100; 25+100; 50+75; 50+100; 75+75; 75+100, LTE CA_41C 100+100 Characteristics Description 100RB+25RB 22M9G7D;22M9W7D; 22M9W7D LTE CA_2C Designation of Emissions 100RB+100RB: 37M6G7D;37M6W7D; 37M6W7D (Note: the necessary 75RB+75RB 28M4G7D;28M4W7D; 28M4W7D bandwidth of which is the LTE CA_7C worst value from the 100RB+100RB 37M6G7D;37M6W7D; 37M6W7D measured occupied 75RB+75RB 28M3G7D;28M4W7D; 28M3W7D bandwidths for each type of LTE CA_38C 100RB+100RB 37M7G7D;37M6W7D; 37M5W7D channel bandwidth configuration.) 100RB+25RB 22M9G7D;22M9W7D; 22M9W7D LTE CA_41C 100RB+100RB 37M6G7D;37M6W7D; 37M6W7D This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 15 of 26 4 Description of Tests 4.1 Conducted Output Power Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 The transmitter output was connected to a calibrated coaxial cable, attenuator and power meter, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The power output at the transmitter antenna port was determined by adding the value of the cable insertion loss to the power reading. The tests were performed at three frequencies (low channel, middle channel and high channel) and on the highest power levels, which can be setup on the transmitters. Note: Reference test setup 1 4.2 Effective (Isotropic) Radiated Power of Transmitter Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 1.5m high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m the receive antenna and by rotating through 360°the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. 8). Calculate power in dBm by the following formula: ERP (dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) Where: Pg is the generator output power into the substitution antenna. Above 1GHz test procedure as below: 1). Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber 2). Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3). Test the EUT in the lowest channel, the middle channel the Highest channel 4). The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5). Repeat above procedures until all frequencies measured was complete. Note: Reference test setup 2 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 16 of 26 4.3 Occupied Bandwidth Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel, middle channel and high channel).The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1 percent of the selected span as is possible without being below 1 percent. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector shall be used since a peak or, peak hold, may produce a wider bandwidth than actual. The trace data points are recovered and are directly summed in linear terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5 percent of the total is reached and that frequency recorded. The process is repeated for the highest frequency data points. This frequency is recorded. The span between the two recorded frequencies is the occupied bandwidth. Note: Reference test setup 1 4.4 Band Edge at Antenna Terminals Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).in the 1MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of 100kHz or 1% of the emission bandwidth of the fundamental emission of the transmitter may be employed. The EUT emission bandwidth is measured as the width of the signal between two points, outside of which all emission are attenuated at least 26dB below the transmitter power. The video bandwidth of the spectrum analyzer was set at thrice the resolution bandwidth. Detector Mode was set to peak or peak hold power. Note: Reference test setup 1 4.5 Spurious And Harmonic Emissions at Antenna Terminal Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyzer, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. On any frequency outside a licensee’s frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB. Compliance with these provisions is based on the use of measurement instrumentation employing a resolution bandwidth of 1 MHz or greater. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. Note: Reference test setup 1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 17 of 26 4.6 Peak-Average Ratio Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 A peak to average ratio measurement is performed at the conducted port of the EUT. For WCDMA signals, the spectrum analyzers Complementary Cumulative Distribution Function (CCDF) measurement profile is used to determine the largest deviation between the average and the peak power of the EUT in a given bandwidth. The CCDF curve shows how much time the peak waveform spends at or above a given average power level. The percent of time the signal spends at or above the level defines the probability for that particular power level. For GSM signals, an average and a peak trace are used on a spectrum analyzer to determine the largest deviation between the average and the peak power of the EUT in a bandwidth greater than the emission bandwidth. The traces are generated with the spectrum analyzer set to zero span mode. Note: Reference test setup 1 4.7 Field Strength of Spurious Radiation Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 150cm high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) the receive antenna and by rotating through 360°the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. 8) Calculate power in dBm by the following formula: ERP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) Where: Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]). Above 1GHz test procedure as below: 1) Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber 2) Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3. Test the EUT in the lowest channel, the middle channel the Highest channel 4. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5. Repeat above procedures until all frequencies measured was complete This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 18 of 26 Note: Reference test setup 3 4.8 Frequency Stability / Temperature Variation Measurement Procedure: Frequency stability testing is performed in accordance with the guidelines of FCC KDB 971168 D01 Power Meas License Digital Systems v03 . The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. Specification – The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5 ppm ) of the center frequency. Time Period and Procedure: 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Note: Reference test setup 4 4.9 Test Setups 4.9.1 Test Setup 1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 19 of 26 4.9.2 Test Setup 2 Figure 1. 30MHz to 1GHz Figure 2. above 1GHz Figure 1. 30MHz to 1GHz Figure 2. above 1GHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 20 of 26 4.9.3 Test Setup 3 Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Figure 3. above 1GHz Figure 2. 30MHz to 1GHz Figure 3. above 1GHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 21 of 26 4.9.4 Test Setup 4 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 22 of 26 4.10 Test Conditions Test Case Test Conditions Test Environment Ambient Climate & Rated Voltage Average Test Setup Test Setup 1 Power, L, M, H Total RF Channels (TX) Transmit (L= low channel, M= middle channel, H= high channel ) Output Test Mode LTE/TM1; LTE/TM2;LTE/TM3 Power Test Environment Ambient Climate & Rated Voltage Data Average Power, Test Setup Test Setup 1 Spectral L, M, H (L= low channel, M= middle channel, H= high Density (if RF Channels (TX) channel ) required) Test Mode LTE/TM1; LTE/TM2;LTE/TM3 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Peak-to-Average Ratio L, M, H (L= low channel, M= middle channel, H= high (if required) RF Channels (TX) channel ) Test Mode LTE/TM1; LTE/TM2;LTE/TM3 Test Environment Ambient Climate & Rated Voltage Modulation Test Setup Test Setup 1 Characteristics RF Channels (TX) M (M= middle channel ) Test Mode LTE/TM1;LTE/TM2;LTE/TM3 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Occupied Bandwidth L, M, H (L= low channel, M= middle channel, H= high RF Channels (TX) channel ) Test Mode LTE/TM1; LTE/TM2;LTE/TM3 Bandwidth Test Environment Ambient Climate & Rated Voltage Emission Test Setup Test Setup 1 Bandwidth L, M, H (L= low channel, M= middle channel, H= high (if RF Channels (TX) channel ) required) Test Mode LTE/TM1; LTE/TM2;LTE/TM3 Test Environment Ambient Climate & Rated Voltage Band Edges Test Setup Test Setup 1 Compliance RF Channels (TX) L, H (L= low channel, H= high channel ) Test Mode LTE/TM1; LTE/TM2;LTE/TM3 Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Spurious Emission at Antenna Terminals L,M, H (L= low channel, M= middle channel, H= high RF Channels (TX) channel ) Test Mode LTE/TM1 Test Environment Ambient Climate & Rated Voltage Field Strength of Test Setup Test Setup 2 Spurious Radiation Test Mode LTE/TM1;LTE/TM2; LTE/TM3;NOTE: If applicable, the EUT conf. that has maximum power density (based on the This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 23 of 26 equivalent power level) is selected. L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) (1) -30 °C to +50 °C with step 10 °C at Rated Voltage; Test Env. (2) VL, VN and VH of Rated Voltage at Ambient Climate. Test Setup Test Setup 4 Frequency Stability L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1;LTE/TM2; LTE/TM3 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 24 of 26 5 Main Test Instruments RE in Chamber Cal. date Cal.Due date Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic Chamber AUDIX N/A SEM001-02 2018/3/13 2021/3/12 Spectrum Analyzer (20Hz-43GHz) Rohde & Schwarz FSU43 SEM004-08 2018/4/2 2019/4/1 BiConiLog Antenna (26-3000MHz) ETS-Lindgren 3142C SEM003-01 2017/6/27 2020/6/26 Horn Antenna (800MHz-18GHz) Rohde & Schwarz HF907 SEM003-07 2018/413 2021/412 Horn Antenna (15-40GHz) Schwarzbeck BBHA 9170 SEM003-15 2017/10/17 2020/10/16 Amplifier (0.1-1300MHz) HP 8447D SEM005-02 2018/9/2 2019/9/2 Low Noise Amplifier (100MHz-18GHz) Black Diamond Series BDLNA-0118-352810 SEM005-05 2018/9/2 2019/9/2 Pre-Amplifier (0.1-26.5GHz) Compliance Directions Systems Inc. PAP-0126 EMC2063 2018/10/20 2019/10/19 Pre-amplifier (26-40GHz) Compliance Directions Systems Inc. PAP-2640-50 SEM005-08 2018/4/2 2019/4/1 Band filter N/A N/A N/A N/A N/A Measurement Software AUDIX e3 V8.2014-6-27 N/A N/A N/A Coaxial Cable SGS N/A SEM026-01 2018/7/12 2019/7/11 Wideband Radio Anristu MT8821C 6201462742 2018/5/2 2019/5/1 CommunicationTeste Wideband Radio Rohde & Schwarz CMW500 W005-02 2018/3/13 2019/3/12 CommunicationTester RF conducted test Inventory Cal. date Cal.Due date Test Equipment Manufacturer Model No. No. (yyyy-mm-dd) (yyyy-mm-dd) Dual Output Mobile Communication Agilent Technologies Inc 66311B W009-09 2018/9/15 2019/9/15 DC Source Signal Analyzer Rohde & Schwarz FSV W025-05 2018/3/13 2019/3/12 Coaxial Cable SGS N/A SEM031-01 2018/7/12 2019/7/11 Attenuator Weinschel Associates WA41 SEM021-09 N/A N/A Signal Generator KEYSIGHT N5173B SEM006-05 2018/9/2 2019/9/2 Shanghai Meteorological Industry Humidity/ Temperature Indicator HTC-1 W006-17 2018/9/10 2019/9/10 Factory Temperature Chamber GIANT FORCE ICT-150-40-CP-AR W027-03 2018/11/27 2019/11/27 Wideband Radio Anristu MT8821C 6201462742 2018/5/2 2019/5/1 CommunicationTeste This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 25 of 26 Cal. Date Cal. Due Inventory Test Equipment Manufacturer Model No. (yyyy-mm- date (yyyy- No. dd) mm-dd) 3m Semi-Anechoic Chamber AUDIX N/A SEM001-02 2018/3/13 2021/3/12 Wideband Radio Anristu MT8821C 6.201E+09 2018/5/2 2019/5/1 CommunicationTeste Wideband Radio Rohde & Schwarz CMW500 W005-02 2018/3/13 2019/3/12 CommunicationTester EXA Signal Analyzer (10Hz-26.5GHz) Agilent Technologies Inc N9010A SEM004-09 2018/4/13 2019/4/12 Spectrum Analyzer (20Hz-43GHz) Rohde & Schwarz FSU43 SEM004-08 2018/4/2 2019/4/1 BiConiLog Antenna (26-3000MHz) ETS-Lindgren 3142C SEM003-01 2017/6/27 2020/6/26 Horn Antenna (800MHz-18GHz) Rohde & Schwarz HF907 SEM003-07 2018/4/13 2021/4/12 Horn Antenna (15-40GHz) Schwarzbeck BBHA 9170 SEM003-15 2017/10/17 2020/10/16 Amplifier (0.1-1300MHz) HP 8447D SEM005-02 2018/9/25 2019/9/24 Compliance Directions Pre-Amplifier (0.1-26.5GHz) PAP-0126 SEM004-11 2018/9/27 2019/9/26 Systems Inc. Compliance Directions PAP-2640- Pre-amplifier (26-40GHz) SEM005-08 2018/4/2 2019/4/1 Systems Inc. 50 Band filter N/A N/A N/A N/A N/A Coaxial Cable SGS N/A SEM026-01 2018/7/12 2019/7/11 Tunable Notch Filter WAINRIGHT Instruments N/A N/A N/A N/A WRCD1700/2000-0.2/40-10EEK GMBH Tunable Notch Filter WAINRIGHT Instruments N/A N/A N/A N/A WRCD800/960-0.2/40-10EEK GMBH HighPass Filter WAINRIGHT Instruments N/A N/A N/A N/A WHK1.2/15G-10SS GMBH HighPass Filter WAINRIGHT Instruments N/A N/A N/A N/A WHKX10-2700-3000-18000-40SS GMBH HighPass Filter WAINRIGHT Instruments N/A N/A N/A N/A WHKX7.0/26.5G-6SS GMBH Band Reject Filter WAINRIGHT Instruments N/A N/A N/A N/A WRCG 824/849-814/859-40/8SS GMBH Band Reject Filter WAINRIGHT Instruments N/A N/A N/A N/A WRCG 1850/1910-1835/1925-40/8SS GMBH e3 V8.2014- Measurement Software AUDIX N/A N/A N/A 6-27 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd.Shenzhen Branch Report No.: HR/2018/C000201 Page: 26 of 26 6 Measurement Uncertainty For a 95% confidence level (k = 2), the measurement expanded uncertainties for defined systems, in accordance with the recommendations of ISO 17025 as following: Test Item Extended Uncertainty Data Transmit Output Power Data Power [dBm] U = ±0.37 dB Bandwidth Magnitude [%] U = ±0.2% Band Edge Compliance Disturbance Power [dBm] U = ±2.0 dB Spurious Emissions, Conducted Disturbance Power [dBm] U = ±2.0 dB For 3 m Chamber: U = ±4.5 dB (30 MHz to 1GHz) Field Strength of Spurious U = ±3.3 dB (above 1 GHz) ERP [dBm] Radiation For 10 m Chamber: U = ±4.5 dB (30 MHz to 1GHz) U = ±3.2 dB (above 1 GHz) Frequency Stability Frequency Accuracy [ppm] U = ±0.24 ppm 7 Photographs - EUT Constructional Details Refer to Appendix A - Photographs of EUT Constructional Details for HR/2018/C0002. The End This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.


Document Created: 2018-12-27 11:14:19
Document Modified: 2018-12-27 11:14:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC