Test Report_PCE_B26_814-824

FCC ID: QISCLT-L29

Test Report

Download: PDF
FCCID_3794443

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Report No.: SZEM180100021804 Email: ee.shenzhen@sgs.com Page: 1 of 21 1 Cover page TEST REPORT Application No: SZEM1801000218RG Applicant: Huawei Technologies Co., Ltd. Manufacturer: Huawei Technologies Co., Ltd.. Factory: Huawei Technologies Co., Ltd. Product Name: Smart Phone Model No.(EUT): CLT-L29 Trade Mark: HUAWEI FCC ID: QISCLT-L29 Standards: 47 CFR Part 2(2018) 47 CFR Part 90S Test Method: FCC KDB 971168 D01 Power Meas License Digital Systems v03 TIA-603-E 2016 Date of Receipt: 2018-02-10 Date of Test: 2018-02-12 to 2018-03-05 Date of Issue: 2018-03-05 Test Result: PASS * * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Authorized Signature: Derek Yang Wireless Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 2 of 21 2 Version Revision Record Version Chapter Date Modifier Remark 01 2018-03-05 Original Authorized for issue by: Tested By (Mike Hu) /Project Engineer Date Checked By (Jim Huang) /Reviewer Date

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 3 of 21 3 Test Summary FCC&IC Test Item Requirements Test Result Verdict Rule No. Effective (Isotropic) §2.1046, ERP≤7W Section 1 of PASS Radiated Power §90.635 BAND 26(814-824)} Appendix B Output Data Peak-Average Section 2 of N/A ≤13dB PASS Ratio Appendix B Modulation Section 3 of §2.1047 Digital modulation PASS Characteristics Appendix B OBW:No limit Section 4 of Bandwidth §2.1049(h), PASS EBW: No limit Appendix B Band Edge §2.1051, Section 5 of 1,≤ -13dBm PASS Compliance §90.691, Appendix B Spurious §2.1051, Section 6 of emissions at 1,≤ -13dBm PASS §90.691 Appendix B antenna terminals Field strength of §2.1051, Section 7 of 1,≤ -13dBm PASS spurious radiation §90.691(a)(1)(2) Appendix B Frequency §2.1055,(a) Section 8 of ≤ ±2.5ppm. PASS stability §90.213 Appendix B This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180 100021804 Page Aof21 Content 2. version: a Teor summary content a eenena. inrormation— 41— Cuert heormaton 42— Geners. DesorenoncrEut 43. TesrMooe aa TestEnvizoment 45. Test Freausny «8 TesrLoxton 470 TestFroum 48 DevamionrronSmnoaros 493 AmomumesrrowSmoaroConemors 410 Onentirorinmion Recuesrep ev me Custouer 411. Tecimon Sreorioation s pescriprionortests s1 Coroucren OuteurPower 0 s2 Erreome (sorrone)ReowrepPowen or Trwisumen 10 53. Ocuneodmowom n 54 BmoEoccar AireinaTeniius i2 55 Srumous Ano Hemvowo Enissionsar Awtcuiw Termwc i2 a5 PeveAremee®wro is 57. Feto Smenamor Srumous Rhownow is 58 Frecusney Stamiim//Tewremsrure Varnon 1 s Tesrserues is #9.1— TestSotgp t is s92. TestSoupe is 898 TestSepo is throreiventetsomnenintuvaneatennee eurnioeeonie acomcavnctucntnoresaacnnataeagies mmtorooninpimacenonsecencetramerimes

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180 100021804 Page Sot21 #94 TestSotrpa i7 s10 TesrCowmons is s manTest nstnuments» 7/ measumement unoentaiimy a PMoToohaphs— EuT constructionaL peralls throneiventetsomnenietovaneatennee eurnioeeonie ocomcavnctucntnoresaacnnataeagies mmtorooninpimacenonsecencetramerimes

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 6 of 21 4 General Information 4.1 Client Information Applicant: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Address of Applicant: Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C Manufacturer: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Address of Manufacturer: Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C Factory: Huawei Technologies Co., Ltd. Administration Building, Headquarters of Huawei Technologies Co., Address of Factory: Ltd., Bantian, Longgang District, Shenzhen, 518129, P.R.C 4.2 General Description of EUT Product Name: Smart Phone Model No.: CLT-L29 Trade Mark: HUAWEI Sample Type: Portable production Antenna Type: PIFA Antenna Antenna Gain: LTE B26: -2.09dBi 4.3 Test Mode Test Mode Test Modes Description LTE/TM1 LTE system, QPSK modulation LTE/TM2 LTE system, 16QAM modulation LTE/TM3 LTE system, 64QAM modulation NOTE: The test mode(s) are selected according to relevant radio technology specifications. 4.4 Test Environment Environment Parameter Selected Values During Tests Relative Humidity 52% Atmospheric Pressure: 1015Pa Temperature TN 25 °C VL 3.6V Voltage : VN 3.82V VH 4.5V NOTE: VL= lower extreme test voltage VN= nominal voltage VH= upper extreme test voltage TN= normal temperature This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 7 of 21 4.5 Test Frequency RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 26697 Channel 26740 Channel 26783 TX LTE BAND26 814.7 MHz 819 MHz 823.3.3 MHz (814-824) 1.4MHz Channel 8697 Channel 8740 Channel 8783 RX 859.7 MHz 864 MHz 868.3 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 26705 Channel 26740 Channel 26775 TX LTE BAND26 815.5 MHz 819 MHz 822.5 MHz (814-824) 3MHz Channel 8705 Channel 8740 Channel 8775 RX 860.5 MHz 864 MHz 867.5 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 26715 Channel 26740 Channel 26765 TX LTE BAND26 816.5 MHz 819 MHz 821.5 MHz (814-824) 5MHz Channel 8715 Channel 8740 Channel 8765 RX 861.5 MHz 864 MHz 866.5 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) / Channel 26740 / TX LTE BAND26 / 819 MHz / (814-824) 10MHz / Channel 8740 / RX / 864 MHz / This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 8 of 21 4.6 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 4.7 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 4.8 Deviation from Standards None. 4.9 Abnormalities from Standard Conditions None. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180 100021804 Page S of21 4.10 Other Information Requested by the Customer None 4.11. Technical Specification Charmcisreics Desaipion Redo Sysom Type t3 ure Suppoted Frequency Range LTE band 2ena.aag T Tetemesion (Do:Brto (ho:art o aas m * Recaling (R: ass to 800 Vie Terget TX Output Rower LTE band 20(@14—804): 23 5Bm TTE bardas(ora—san| Eit McfiNie: [ Nie; BJro We Charecterstcs Desaipion Designation af Emissions mnogr0:mmow70; 1nmowro (NMote: the necessary bandwidth of which is the worst value from the alce70;alleaw70; 2MESWzO measured occupied banduitths for UE 020028 (BM—820) qugacypytsoW7D;4WBW70 each tpe. of. chamnel. bandwith sisecrojmarw70; sverwro confauraton) — ‘ throneiventetsomnenietovaneatennee eurnioeeonie ocomcavnctucntnoresaacnnataeagies mmtorooninpimacenonsecencetramerimes

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 10 of 21 5 Description of Tests 5.1 Conducted Output Power Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 The transmitter output was connected to a calibrated coaxial cable, attenuator and power meter, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The power output at the transmitter antenna port was determined by adding the value of the cable insertion loss to the power reading. The tests were performed at three frequencies (low channel, middle channel and high channel) and on the highest power levels, which can be setup on the transmitters. Note: Reference test setup 1 5.2 Effective (Isotropic) Radiated Power of Transmitter Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 0.8m high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m the receive antenna and by rotating through 360° the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. 8). Calculate power in dBm by the following formula: ERP (dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) Where: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 11 of 21 Pg is the generator output power into the substitution antenna. Above 1GHz test procedure as below: 1). Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber 2). Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3). Test the EUT in the lowest channel, the middle channel the Highest channel 4). The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5). Repeat above procedures until all frequencies measured was complete. Note: Reference test setup 2 5.3 Occupied Bandwidth Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel, middle channel and high channel).The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1 percent of the selected span as is possible without being below 1 percent. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector shall be used since a peak or, peak hold, may produce a wider bandwidth than actual. The trace data points are recovered and are directly summed in linear terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5 percent of the total is reached and that frequency recorded. The process is repeated for the highest frequency data points. This frequency is recorded. The span between the two recorded frequencies is the occupied bandwidth. Note: Reference test setup 1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 12 of 21 5.4 Band Edge at Antenna Terminals Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).in the 1MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of 100kHz or 1% of the emission bandwidth of the fundamental emission of the transmitter may be employed. The EUT emission bandwidth is measured as the width of the signal between two points, outside of which all emission are attenuated at least 26dB below the transmitter power. The video bandwidth of the spectrum analyzer was set at thrice the resolution bandwidth. Detector Mode was set to peak or peak hold power. Note: Reference test setup 1 5.5 Spurious And Harmonic Emissions at Antenna Terminal Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyzer, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. On any frequency outside a licensee’s frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB. Compliance with these provisions is based on the use of measurement instrumentation employing a resolution bandwidth of 1 MHz or greater. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. Note: Reference test setup 1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 13 of 21 5.6 Peak-Average Ratio Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 A peak to average ratio measurement is performed at the conducted port of the EUT. For WCDMA signals, the spectrum analyzers Complementary Cumulative Distribution Function (CCDF) measurement profile is used to determine the largest deviation between the average and the peak power of the EUT in a given bandwidth. The CCDF curve shows how much time the peak waveform spends at or above a given average power level. The percent of time the signal spends at or above the level defines the probability for that particular power level. For GSM signals, an average and a peak trace are used on a spectrum analyzer to determine the largest deviation between the average and the peak power of the EUT in a bandwidth greater than the emission bandwidth. The traces are generated with the spectrum analyzer set to zero span mode. Note: Reference test setup 1 5.7 Field Strength of Spurious Radiation Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v03 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 80cm high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) the receive antenna and by rotating through 360° the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. 8) Calculate power in dBm by the following formula: ERP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 14 of 21 Where: Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]). Above 1GHz test procedure as below: 1) Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber 2) Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3. Test the EUT in the lowest channel, the middle channel the Highest channel 4. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5. Repeat above procedures until all frequencies measured was complete Note: Reference test setup 3 5.8 Frequency Stability / Temperature Variation Measurement Procedure: Frequency stability testing is performed in accordance with the guidelines of FCC KDB 971168 D01 Power Meas License Digital Systems v03 . The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. Specification – The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5 ppm ) of the center frequency. Time Period and Procedure: 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 15 of 21 transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Note: Reference test setup 4 5.9 Test Setups 5.9.1 Test Setup 1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 16 of 21 5.9.2 Test Setup 2 Figure 1. 30MHz to 1GHz Figure 2. above 1GHz Figure 1. 30MHz to 1GHz Figure 2. above 1GHz 5.9.3 Test Setup 3 Figure 1. Below 30MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 17 of 21 Figure 2. 30MHz to 1GHz Figure 3. above 1GHz Figure 2. 30MHz to 1GHz Figure 3. above 1GHz 5.9.4 Test Setup 4 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 18 of 21 5.10 Test Conditions Test Case Test Conditions Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Average Power, L, M, H RF Channels (TX) Total (L= low channel, M= middle channel, H= high channel ) Transmit Output Test Mode LTE/TM1;LTE/TM2;LTE/TM3. Power Test Environment Ambient Climate & Rated Voltage Data Average Power, Test Setup Test Setup 1 Spectral Density L, M, H (if required) RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1;LTE/TM2;LTE/TM3. Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Peak-to-Average Ratio L, M, H (if required) RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1;LTE/TM2;LTE/TM3. Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Modulation Characteristics M RF Channels (TX) (M= middle channe ) Test Mode LTE/TM1;LTE/TM2;LTE/TM3. Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Occupied Bandwidth L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1;LTE/TM2;LTE/TM3. Bandwidth Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Emission Bandwidth L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high (if required) channel ) Test Mode LTE/TM1;LTE/TM2;LTE/TM3. Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 Band Edges Compliance L, H RF Channels (TX) (L= low channel, H= high channel ) Test Mode LTE/TM1;LTE/TM2;LTE/TM3. Spurious Emission at Antenna Test Environment Ambient Climate & Rated Voltage This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 19 of 21 Terminals Test Setup Test Setup 1 L,M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1. Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 2 LTE/TM1; NOTE: If applicable, the EUT conf. that Field Strength of Spurious Test Mode has maximum power density (based on the Radiation equivalent power level) is selected. L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) (1) -30 °C to +50 °C with step 10 °C at Rated Voltage; Test Env. (2) VL, VN and VH of Rated Voltage at Ambient Climate. Frequency Stability Test Setup Test Setup 4 L, M, H RF Channels (TX) (L= low channel, M= middle channel, H= high channel ) Test Mode LTE/TM1;LTE/TM2;LTE/TM3. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 20 of 21 6 Main Test Instruments RE in Chamber Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic 1 ETS-LINDGREN N/A SEM001-01 2017-05-10 2018-05-10 Chamber Agilent 2 EMI Test Receiver N9038A SEM004-05 2017-10-09 2018-10-09 Technologies BiConiLog Antenna 3 ETS-LINDGREN 3142C SEM003-02 201711-15 2020-11-15 (26-3000MHz) Double-ridged horn 4 ETS-LINDGREN 3117 SEM003-11 2015-10-17 2018-10-17 (1-18GHz) Horn Antenna (18- 5 ETS-LINDGREN 3160 SEM003-12 2017-11-24 2020-11-24 26GHz) Pre-amplifier (0.1- Agilent 6 8447D SEM005-01 2017-04-14 2018-04-14 1300MHz) Technologies Compliance Pre-Amplifier (0.1- 7 Directions PAP-0126 SEM004-10 2017-10-17 2018-10-17 26.5GHz) Systems Inc. 8 Band filter Amindeon 82346 SEM023-01 N/A N/A Universal radio 9 communication Rohde &Schwarz CMU200 SEM010-01 2017-10-09 2018-10-09 tester Universal radio 10 communication Rohde &Schwarz CMW500 SEM010-03 2017-10-23 2018-10-23 tester 11 DC Power Supply Zhao Xin RXN-305D SEM011-02 2017-10-09 2018-10-09 BiConiLog Antenna 12 Schwarzbeck VULB9163 SEM003-05 2015-10-17 2018-10-17 (30MHz-3GHz) Horn Antenna 13 Rohde &Schwarz HF907 SEM003-06 2015-06-14 2018-06-14 (800MHz-18GHz) RE in Chamber Cal. Date (yyyy- Cal. Due date Item Test Equipment Manufacturer Model No. Inventory No. mm-dd) (yyyy-mm-dd) 10m Semi-Anechoic 1 SAEMC FSAC1018 SEM001-03 2017-05-10 2018-05-10 Chamber EMI Test Receiver 2 Rohde & Schwarz ESR SEM004-03 2017-04-14 2018-04-14 (9k-7GHz) Trilog-Broadband 3 Schwarzbeck VULB9168 SEM003-18 2016-06-29 2019-06-29 Antenna(30M-1GHz) Sonoma 4 Pre-amplifier 310N SEM005-03 2017-07-06 2018-07-06 Instrument Co 5 .Loop Antenna ETS-Lindgren 6502 SEM003-08 2015-08-14 2018-08-14 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180100021804 Page: 21 of 21 RF connected test Inventory Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. No. (yyyy-mm-dd) (yyyy-mm-dd) Humi/ Temp 1 MingGao TH101B W006-09 2017-03-09 2018-03-09 Indicator Rohde 2 Signal Analyzer FSV W005-02 2017-03-06 2018-03-06 Schwarz 3 Barometer ChangChun DYM3 SEL0088 2017-05-24 2018-05-24 Dual Output Mobile Agilent 4 Communication DC Technologies 66319D W009-02 2017-07-23 2018-07-23 Source Inc 5 Digital Multimeter Fluke 15B+ W055-01 2017-03-09 2018-03-09 Wideband Radio Rohde & 6 CMW500 W005-02 2017-03-06 2018-03-06 Communication Tester Schwarz Wideband Radio Rohde & 7 CMW500 W005-02 2017-03-06 2018-03-06 CommunicationTester Schwarz 7 Measurement Uncertainty For a 95% confidence level (k = 2), the measurement expanded uncertainties for defined systems, in accordance with the recommendations of ISO 17025 as following: Test Item Extended Uncertainty Data Transmit Output Power Data Power [dBm] U = 0.37 dB Bandwidth Magnitude [%] U = 0.2% Band Edge Compliance Disturbance Power [dBm] U = 2.0 dB Spurious Emissions, Conducted Disturbance Power [dBm] U = 2.0 dB For 3 m Chamber: U = 4.5 dB (30 MHz to 1GHz) Field Strength of Spurious U = 3.3 dB (above 1 GHz) ERP [dBm] Radiation For 10 m Chamber: U = 4.5 dB (30 MHz to 1GHz) U = 3.2 dB (above 1 GHz) Frequency Stability Frequency Accuracy [ppm] U = 0.24 ppm 8 Photographs - EUT Constructional Details Refer to Appendix A - Photographs of EUT Constructional Details for SZEM1801000218RG The End This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.


Document Created: 2018-03-05 03:26:56
Document Modified: 2018-03-05 03:26:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC