SAR test report_part 4

FCC ID: QISAMN-LX3

RF Exposure Info

Download: PDF
FCCID_4239084

Add: No.51 Xuey uan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax:+86—10—62304633—2504 E—mail: ettl@chinatil.com hitpsvww.chinsttlen Measurement Conditions DASY system configuration, as far as notgiven on page 1. DASY Version DASYS2 §2.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 2600 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temporature Permittivity Conductivity Nominal Head TSL parameters 22.0°C 39.0 1.96 mhaim Measured Hoad TSL parameters (22.0 £0.2) °C 40.1 2 6% 2.01 mho‘m £ 6 % Head TSL temperature change during test <1.0 °C — E+ SAR resultwith Head TSL SAR averaged over 1_cm* _(1 g) of Head TSL Condition SAR measured 250 mW input power 136 mW1 SAR for nominal Head TSL parameters normalized to 1W 54.1 mW Ig # 18.8 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL Condition SAR measured 250 mW input power 6.03 mW /g SARfor nominal Head TSL parameters normalized to 1W 24.1 mW 1g 4 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0°C §2.5 2.16 mhoim Measured Body TSL parameters (22.0 2 0.2) °C §2.1£6% 2.15 mho‘im & 6 % Body TSL temperature change during test <1.0 °C — m SAR result with Body TSL SAR avoraged over 1 _cm"_(1 g) of Body TSL Condition SAR measured 250 mW input power 13.6 mW/g SAR for nominal Body TSL parameters normalized to 1W 54.5 mW /g £ 18.8 % (k=2) SAR averaged over 10 Cm" (10 g) of Body TSL Condition SAR measured 250 mW input power 6.06 mW / g SAR for nominal Body TSL parameters normalized to 1W 24.3 mW /g £ 18.7 % (k=2) Certificate No: Z18—60094 Page 3 of 8

r\" in Collaboration with [ TTL s_p e a _ Add: No.$1 Xuey uan Road, Haidian District, Beljing, 100194, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettI@chinattLcom hitp:www.chinattlen Appendix(Additional assessments outside the scope of CNAS LO0570) Antonna Parameters with Head TSL Impedance, transformed to feed point 48.10—7.55]0 Returm Loss —22.008B Antenna Parameters with Body TSL Impedance, transformed to feed point 46.60—7.06]0 Retum Loss —21.908 General Antenna Parameters and Design Electrical Delay (one direction) | 1.014 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made ofstandard semirigid coaxial cable. The center conductor of the feeding lineis direcily connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend orthe soldered connections nearthe feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG ] Certificate No: Z18—60094 Page 4 of 8

7TL :f_z_fi_s_ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Te: +86—10—62304633—2079 Fax: +86—10—062304633—2504 E—mail: citl@chinattl.com hitp/www.chinattLon DASYS Validation Report for Head TSL Date: 05.02.2018 Test Laboratory: CTTL, Beijing China DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600 V2 — SN: 1025 Communication System: UID 0, CW; Frequency: 2600 MHz; Duty Cyele: 1 :1 Medium parameters used: £= 2600 MHz; 0 = 2.014 S/m; er= 40.09; p = 1000 kg/m3 Phantom section: F lat Section Measurement Standard: DAS Y5 (IEEEAEC/ANSI C63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN7464; ConvF(7.76, 7.76, 7.76); Calibrated: 9/12/2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn1525; Calibrated: 10/2/2017 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 + Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5 mm, dy=5mm, dz=5mm Reference Value = 98.50 V/m; Power Drift=0.00 dB Peak SAR (extrapolated) = 29.6 W/kg SAR(I g)=13.6 Wikg:; SAR(10 g)=6.03 W/kg Maximum value of SAR (measured) = 23.5 W/kg ~4.80 —0.59 ~14.39 +19.18 ~23.98 L. 0 dB =23.5 Wikg =13.71 dB Wkg Certificate No: Z1 8—60094 Page 5 of 8

* in Collaboration with TTL a CALIBRATION LABORATORY Add: No.51 Xuey wan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitprtwwnw.chinattLen Impedance Measurement Plot for Head TSL Tei SiT Log nag 10.00087 ref 0.000d0 [F] +*" rro—ma en rmanccs 10.00 30.00 20.00 10. 00 5.000 p 16. 68 h ~20. 00 ~30. 00 ~40. 00 «40. 00 [MIRRB s1 satch (r—Jx) scale 1.000u {ri cel] s1 2.6000000 oiz 48.007 o —7. 58502 0. .1 Certificate No: Z18—60094 Page 6 of 8

mm in Colleboration with ©7‘"7J, s p e a q \lipzzzzzee~" CALIBRATION LABORATORY Add: No.51 Xuey uan Road, Hadian District, Beijing, 100191,China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettI@chinattL.com hitpriwwwchinattLen DASYS Validation Report for Body TSL Date: 05.02.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600 V2 — SN: 1025 Communication System: UID 0, CW; Frequency: 2600 MHz; Duty Cycle: 1 :1 Medium parameters used: {= 2600 MHz; a = 2.146 S/m; s, = 52.09; p = 1000 kgfm’ Phantom section: Right Section Mcasurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: Probe: EX3DV4 — SN7464; ConvF(7.84,7.84, 7.84); Calibrated: 9/12/2017; m Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn1525; Calibrated: 10/2/2017 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 & Measurement SW : DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 # (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/(Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 83.79 V/m; Power Drift= 0.02 dB Peak SAR (extrapolated) = 29.7 W/kg SAR(L g)= 13.6 Wikg; SAR(IO g)= 6.06 Wikg Maximum value of SAR (measured) = 23.6 W/kg L. 0 dB =23.6 Wikg =13.73 dB Wikg Certificate No: £18—60094 Page 7 of 8

TTE a ©*6 C Add: No.51 Xueyusn Road, Haidian District, Bejjing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt!@chinaitl.com hitpoiwww.chinattLen Impedance Measurement Plot for Body TSL Tei siZ tog nay 10.00007 nef 0.000c0 [#i] 400 212000000ons~21—960 cb 40.c0 30.c0 20.c0 10.00 o.ccop) r( —10.00 «20.c0 —50.00 ~10.00 ~50.00 IPIMM 511 smith (refx) Scale 1.000u {e1 bel) »2.. 28000000 onz 46.641 o —7.0563 0. $.67 Certificate No: Z18—60094 Page 8 of 8

Calibration Laboratory of S Schwelzerischer Kalibrierdienst Schmid & Partner [ Service suisse détalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, $004 Zurich, Switzertand S swiss Calibration Sorvice Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one af the signatories to the EA Mutilateral Agreement for the recognition of calibration certificates Ctient TA—SH (Auden) Certificate No: DAE4—1291_Dec18 |CALIBRATION CERTIFICATE Onject DAE4 — SD 000 DO4 BM — SN: 1291 Calbration procedure(s) QA CAL—06.v29 Calibration procedure for the data acquisition electronics (DAE) Callbration cate: December 04, 2018 This calibrabion certiicate documents the traceabilty to national standards, which reallze the physical units of measurements (S1). The measurements and the uncertainties with confidence probabilty are given on the following pages and are part of the certificate. All callbrations have been conducted in the closed laboratory faciity: environment temperature (22 & 3)°C and humidity < 70%. Caltoration Equipment used (M&TE critical for calibration) Primary Standards 10 # Gal Date (Gertificate No.) Scheduled Calibration Keithiey Muttimeter Type 2001 Sh: os10278 03—Sep—18 (No:23488) Sep—19 Secondary Standards 10 # Chack Date (in house) Schedulad Check Auto DAE Calibration Unit SE UWS 053 AA 1001 O4<Jan—18 (in house chack) In house check: Jan—19 Caltbrator Box V2.1 SE UMS 006 AA 1002 04—Jan—18 (in house check) In house check: Jan—19 Name Function Signature Callbrated by: Dominique Steffen Laboratory Technician ,@ Approved by: (&ven Kann Deputy Manager f /gf% »¥. ;’ Issued: Decamber 4, 2018 This calibration certificate shall not be reproduced except in full without writtan approval of tha laboratory. Certificate No: DAE4—1291_Dec18 Page 1 of 5

Calibration Laboratory of Schweizerischer Kallbrierdienst Schmid & Partner Service sulsse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Callbration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Muttilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters * DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. * Connector angle; The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. * The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. * DC Voltage Measurement Linearity: Veritication of the Linearity at +10% and —10% of the nominal calibration voltage. Influence of offset voltage is included in this measurement. * Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. * Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. * AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage * Input Offset Measurement Output voltage and statistical results over a large numberof zero voltage measurements. * Input Offset Current: Typical value for information; Maximum channel input offset current, not considering the input resistance. * Input resistance: Typical value for information: DAE input resistance at the connector, during internal auto—zeroing and during measurement. * Low Baitery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. «_ Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—1291_Dec18 Page 2 of 5

C DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1198 6.1uV . full range = —100...+300 mV Low Range: 1LSB = 61nV , full range = > ... +8mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors s ¥ 2 High Range 402.580 + 0.02% (k=2) 408.249 £ 0.02% (k=2) 403.163 £0.02% (k=2) Low Range 3.97560 £ 1.50% (k=2) 3.97886 £ 1.50%(k=2) 3.97558 £ 1.50% (k=2) Connector Angle i Connector Angle to be used in DASY system 164.5°%41° Certificate No: DAE4—1291_Dec18 Page 3 of 5

Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltage Linearity High Range Reading (V) Difference (1V) Error (%) Channel X + Input 20003851 1.95 0.00 Channel X +Input 20006.61 1.29 0.01 Channel X > Input ©20003.34 2.94 —0.01 Channel Y + Input 200036.77 0.05 0.00 Channel Y + Input 20003.65 +1.54 —0.01 Channel Y > Input +20006.11 0.22 —0.00 Channel 2 + Input 200035.08 ~1.41 —0.00 Channel Z + Input 20002.62 —2.58 —0.01 Channel Z > Input +20006.40 —0.06 0.00 Low Range Reading (rV) Difference (V) Error (%) Channel X + Input 2001.29 0.31 0.02 Channel X + Input 201.13 0.32 0.16 Channel X ~Input —198.59 0.30 +0.15 Channel Y + Input 2000.40 —0.49 —0.02 Channel Y + Input 200.21 —0.66 —0.33 Channel Y > Input +199.89 —0.99 0.50 Channel Z + Input 2000.44 —0.41 —0.02 Channel Z + Input 199.70 —1.05 —0.52 Channel Z — Input —200.88 +1.78 0.89 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 seo; Measuring time: 3 sec Common mode High Range Low Range Input Voltage (mV) Average Reading (uV) Average Reading (1V) Channel X 200 10.02 7.91 —200 —6.52 —8.20 Channel Y 200 14.18 13.58 +200 +15.10 ~15.62 Channel Z 200 ~17.07 ~17.23 ~200 14.74 14.83 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec: Measuringtime: 3 sec Input Voltage (mV) Channel X (uV) Channel Y (uV) Channel Z (uV) Channel X 200 > —0.01 ~4.47 Channel Y 200 7.58 — 0.48 Channel Z 200 11.17 4.87 Certificate No: DAE4—1291_Deci8 Page 4 of 5

C 4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec: Measuring time: 3 sec High Range (LSB) Low Range (LSB) Channel X 16117 16241 Channel Y 15930 16718 Channel Z 16177 17128 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10MG Average (wV) min. Offset(uV) max. Offset (uV) * [(’:“,’;""‘" Channel X —0.59 +1.81 0.89 0.47 Channel Y 147 —0.04 2.05 0.45 Channel Z. 112 —2.70 0.51 0.57 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channel X 200 200 Channel Y 200 200 Channel Z 200 200 Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vee) +7.9 Supply (— Vee) —7.6 Power Consumption (Typical values for information) Typicalvalues Switched off(mA) Stand by (mA) Transmitting (mA) Supply (+ Vee) +0.01 +6 +14 Supply (— Vee) —0.01 —8 8 Certificate No: DAE4—1291_Dec18 Page 5 of 5

FCC SAR Test Report Report No: R1903H0043-S1 ANNEX K:The EUT Appearances and Test Configuration The Detailed EUT Appearance and Test Configuration refer to EUT Appearance and SAR Test Setup. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 175 of 175 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.


Document Created: 2019-04-15 09:14:03
Document Modified: 2019-04-15 09:14:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC