TEST REPORT

FCC ID: QEABEAR9R

Test Report

Download: PDF
FCCID_1052274

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 Application No. : LK228761(4) Client : KID GALAXY INC. TOWER 2, UNIT 425B MANCHESTER, 150 DOW STREET NH03101 U.S.A. Sample Description : One(1) submitted sample(s) stated to be RC POLAR BEAR of Model No. 10444 (K231) Radio Frequency : 49.860MHz Receiver Rating : 3 x 1.5V AAA size batteries No. of submitted sample : Three (3) piece(s) *** Date Received : 2008-08-29 Test Period : 2008-09-17 to 2008-09-24 Test Requested : FCC Part 15 Certification. Test Method : 47 CFR Part 15 (10-1-07 Edition) ANSI C63.4 – 2003 Test Result : See attached sheet(s) from page 2 to 11. Conclusion : The submitted sample was found to comply with requirement of FCC Part 15 Subpart B. For and on behalf of CMA Industrial Development Foundation Limited Authorized Signature : ____________________________________________________ Mr. Wong Lap-pong, Andrew Assistant Manager Electrical Division Page 1 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 Table of Contents 1 General Information ............................................................................................................................ 3 1.1 General Description .................................................................................................................... 3 1.2 Location of the test site ............................................................................................................... 4 1.3 List of measuring equipment....................................................................................................... 5 2 Description of the radiated emission test ............................................................................................ 6 2.1 Test Procedure............................................................................................................................. 6 2.2 Test Result................................................................................................................................... 6 2.3 Radiated Emission Measurement Data ....................................................................................... 7 3 Description of the Line-conducted Test.............................................................................................. 8 3.1 Test Procedure............................................................................................................................. 8 3.2 Test Result................................................................................................................................... 8 3.3 Graph and Table of Conducted Emission Measurement Data .................................................... 8 4 Photograph .......................................................................................................................................... 9 4.1 Photographs of the Test Setup for Radiated Emission and Conducted Emission....................... 9 4.2 Photographs of the External and Internal Configurations of the EUT........................................ 9 5 Supplementary document.................................................................................................................. 10 5.1 Bandwidth ................................................................................................................................. 10 5.2 Duty cycle ................................................................................................................................. 10 5.3 Transmission time ..................................................................................................................... 10 6 Appendices........................................................................................................................................ 11 Page 2 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 1 General Information 1.1 General Description The equipment under test (EUT) is a receiver for RC POLAR BEAR . It operates at 49.860MHz and the oscillation of radio control is generated by a LRC circuit. The EUT is powered by 3 x 1.5V AAA size batteries. When it switched on and received a radio control signal, it will be running to corresponding direction. The brief circuit description is listed as follows: - Q2 and associated circuit act as a RF receiver. - U1 and associated circuit act as a decoder. - Q3 – Q8 and associated circuit act as a motor driver. Page 3 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 1.2 Location of the test site Radiated emissions measurements are investigated and taken pursuant to the procedures of ANSI C63.4 – 2003. A Semi-Anechoic Chamber Testing Site is set up for investigation and located at: Ground Floor, Yan Hing Centre, 9 – 13 Wong Chuk Yeung Street, Fo Tan, Shatin, New Territories, Hong Kong. Conducted emissions measurements are investigated and also taken pursuant to the procedures of ANSI C63.4 – 2003. A shielded room is located at : Ground Floor, Yan Hing Centre, 9 – 13 Wong Chuk Yeung Street, Fo Tan, Shatin, New Territories, Hong Kong. Page 4 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 1.3 List of measuring equipment Equipment Manufacturer Model No. Serial No. Calibration Due Date EMI Test Receiver R&S ESCI 100152 2008-10-14 Broadband Antenna Schaffner CBL6112B 2692 2009-01-21 Page 5 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 2 Description of the radiated emission test 2.1 Test Procedure Radiated emissions measurements are investigated and taken pursuant to the procedures of ANSI C63.4 – 2003. The equipment under test (EUT) was placed on a non-conductive turntable with dimensions of 1.5m x 1m and 0.8m high above the ground. 3m from the EUT, a broadband antenna mounting on the mast received the signal strength. The turntable was rotated to maximize the emission level. The antenna was then moving along the mast from 1m up to 4m until no more higher value was found. Both horizontal and vertical polarization of the antenna were placed and investigated. For below 30MHz, a loop antenna with its vertical plane is placed 3m from the EUT and rotated about its vertical axis for maximum response at each azimuth about the EUT. And the centre of the loop shall be 1 m above the ground. A signal generator was used to radiate an unmodulated continuous wave (CW) signal to the EUT (superregenerative receiver) at its operating frequency in order to “cohere” the characteristic broadband emissions from the receiver. 2.2 Test Result The frequencies from 30MHz to 1000MHz were investigated, and emissions more 20dB below limited were not reported. Thus, those higher emissions were presented in next page (section 2.3) The emissions meeting the requirement of section 15.109 are based on measurements employing the CISPR quasi-peak detector below 1000MHz and average detector for frequencies above 1000MHz. It was found that the EUT meet the FCC requirement. Page 6 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 2.3 Radiated Emission Measurement Data Radiated emission pursuant to the requirement of FCC Part 15 subpart B Frequency Polarity Reading at Antenna and Field Limit at 3m Margin (MHz) (H/V) 3m Cable factor Strength (dBµV/m) (dB) (dBµV/m) (dB) (dBµV/m) 48.582 V 25.3 10.5 35.8 40.0 -4.2 49.002 V 26.9 10.5 37.4 40.0 -2.6 49.436 V 28.1 10.5 38.6 40.0 -1.4 50.295 V 29.6 8.8 38.4 40.0 -1.6 50.716 V 27.6 8.8 36.4 40.0 -3.6 52.808 V 24.2 8.8 33.0 40.0 -7.0 96.753 V 22.2 9.4 31.6 43.5 -11.9 97.177 V 22.5 9.4 31.9 43.5 -11.6 97.601 V 22.2 9.4 31.6 43.5 -11.9 98.017 V 21.5 9.4 30.9 43.5 -12.6 432.940 V 11.0 18.6 29.6 46.0 -16.4 Page 7 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 3 Description of the Line-conducted Test 3.1 Test Procedure Conducted emissions measurements are investigated and also taken pursuant to the procedures of ANSI C63.4 – 2003. The EUT was setup as described in the procedures, and both lines were measured. 3.2 Test Result No measurement is required as the EUT is a battery-operated product. 3.3 Graph and Table of Conducted Emission Measurement Data Not Applicable Page 8 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 4 Photograph 4.1 Photographs of the Test Setup for Radiated Emission and Conducted Emission For electronic filing, the photos are saved with filename TSup1.jpg to TSup2.jpg. 4.2 Photographs of the External and Internal Configurations of the EUT For electronic filing, the photos are saved with filename ExPho1.jpg to ExPho2.jpg and InPho1.jpg to InPho2.jpg. Page 9 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 5 Supplementary document The following document were submitted by applicant, and for electronic filing, the document are saved with the following filenames: Document Filename ID Label/Location LabelSmp.jpg Block Diagram BlkDia.pdf Schematic Diagram Schem.pdf PCB Layout PCB.pdf Part List PartList.pdf Users Manual UserMan.pdf Operational Description OpDes.pdf 5.1 Bandwidth Not Applicable 5.2 Duty cycle Not Applicable 5.3 Transmission time Not Applicable Page 10 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AK035593-001 Date : 2008-12-10 6 Appendices A1. Photos of the set-up of Radiated Emissions 1 page A2. Photos of External Configurations 1 page A3. Photos of Internal Configurations 1 page A4. ID Label/Location 1 page A5. Block Diagram 1 page A6. Schematics Diagram 1 page A7. PCB Layout 4 pages A8. Part List 2 pages A9. User Manual 1 page A10. Operation Description 1 page ***** End of Report ***** Page 11 of 11 FCC ID: QEABEAR9R This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com


Document Created: 2009-01-03 02:49:00
Document Modified: 2009-01-03 02:49:00
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC